Cat4507, Supervisor II+ and EIGRP support
Hello!
Could anyone explain me this phenomenon? I have Catalyst 4507R with redundant Supervisors II+ (WS-X4013+). Both supervisors have IOS 12.2(25)EWA3.
This Catalyst runs EIGRP and it works just fine.
But when I looked into this document
http://www.cisco.com/en/US/products/hw/switches/ps4324/products_data_sheet09186a0080197424.html
I found out that my switch doesn't support EIGRP!
Then I went to Feature Navigator to check it and again it states that Supervisor II+ doesn't support EIGRP.
But it works! I'm running EIGRP alright.
Could anyone explain it?
Thanks in advance!
With new IOS packaging(starting 12.2(25)SG), this has been taken care off
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/relnotes/ol_5184.htm#wp618071
Similar Messages
-
Is EIGRP an option with a UC540 or am I missing something? I see bgp, ospf, rip and a few others as options but no eigrp. I am trying to tunnel remote clinics back to our main site and have done this successfully with the UC540 and simple VPN tunnel.
Now I want to try and streamline the process by using a GRE tunnel and EIGRP. I seem to be striking out though.
Any help is much appreciated.
ThanksIs it that Cisco doesn't support it, or that it won't work? The CLI commands are there for other routing protocols, with the exception of EIGRP.
-
"EIGRP supports multiple protocols. EIGRP can exchange routes for IP, AppleTalk and IPX/SPX networks" What about RIP, IGRP, OSPF? They only support IP?
Hello Hector,
you can check using feature navigator
www.cisco.com/go/fn
then search by feature
write EIGRP and search
select
MPLS VPN support for EIGRP between Provider Edge and Customer Edge
in the case of C7200 I tried to search (I guessed it is using 12.3(8)T11)
the system says first release is 12.3(17c)
for sure it is supported on C6506 with 12.2(18)SXF because we are using it and so also for 12.2(33)SRB1 on C7606.
for 12.2(18)S you can see that 12.2(25)S supports it there are good chances it is fine.
I have some doubts that 12.3(10) and 12.2.(28a) supports it
12.3(22a) can be fine
another way to see is to search in the command reference here it is a list of first releases to introduce the command address-family ip vrf
Release
Modification
12.0(22)S
This command was introduced.
12.2(15)T
This command was integrated into 12.2(15)T.
12.2(18)S
This command was integrated into 12.2(18)S.
12.2(27)SBC
This command was integrated into 12.2(27)SBC.
12.2(33)SRA
This command was integrated into Cisco IOS Release 12.2(33)SRA.
12.2SX
This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.
see
http://www.cisco.com/en/US/docs/ios/iproute/command/reference/irp_eig1.html#wp1021830
Hope to help
Giuseppe -
I am having difficulty: we are running a windows server 2003 - mail and outlook support 2007 and upwards, how do I get the brand new apple machines to work with the 2003 version of server
I may be way out, but do you know about this product, would it help integrate the Macs for you.
https://www.thursby.com/sites/default/files/images/ADmitMacv8_SPD.pdf -
If anyone has a solution for getting the Mecury Playpack Engine GPU acceleration to work with Premiere Pro CS6 on an iMAC 2011, please let me know. Like I wonder if you could Thunderbolt an External graphics card somehow? Or is an upgrade possible? Ahh...not worth the risk.
Please, if you have a solution for me, let me know. Otherwise I find it pretty frustrating that I purchased a top-end iMAC, fully maxed-out in every way possible, and that the iMac doesn't support Adobe Premiere's Mercury Playback Engine GPU acceleration. Also, an old USB 2.0 Hub and thus the built-in SD card reader is slow. If you have SD cards with 95MB/s Transfer, Read and Write speeds, the iMAC will only transfer at around 30MB/s if you're lucky. Technically 480Mbs which is around 50MB/s but I haven't seen those speeds.
I figured this could at least be circumvented with a Thunderbolt SD card reader or a Thunderbolt to USB 3.0 adapter but of course no such thing exists.
Well, nothing with a reasonable price tag. This all might seem trivial to some but when you're uploading 24 hours of HD video footage from a 128GB SDXC card, the speed makes a big difference.
And come on, no BluRay support? Ridiculous. I get the politics of why but still, just ridiculous. It would be nice to be able to burn a BluRay to watch in my home theater system. There are other methods but BluRay is convenient and great for backing up large Video Files. Unfortunately BluRay looks like it's not going to make it. Maybe cable distribution companies will increase their Internet upload speeds one day and I can just store everything in the cloud and watch full length movies(that I've created) on Vimeo.
Anyways, I went and took a look at the hardware Apple stuffed inside my fancy (3.4 Ghz i7, 16GB 1333 DDR3, 2GB AMD 6970M, 256 GB SSD Internal and 2TB 7200 Internal) machine and it appears to be pretty middle of the range stuff. It's an iMAC, not a Mac Pro so why am I griping? Because my 2009 PC(which I tricked out over the last two years) is faster and does support the Mercury Playback Engine. I spent $2100 total on this PC which includes all my upgrades. I spent around $3300 on the iMAC. I feel ripped off.
Yes, I do love my iMAC on multiple levels but had I known my dated 2009 PC would render video projects faster, I would have gone with a MAC Pro or just a new PC. It seems that Mac is moving completely away from making high-end computers for niche markets(video editing) and focusing on their tiny laptops, IPADS and IPhones for the masses. Obviously smart from a capitalistic perspective(at present at least) but very frustrating for some.
I was actually told to purchase a MAC for video editing. I've been a PC guy for 15 years. I went with the iMAC because I had read many good things about it(probably just Apple propaganda) and also the MAC PRO was to be discontinued. Also the MAC Pro would have been triple the cost for what didn't seem like a whole lot more.
It's one's thing to prepackage a computer with inferior hardware(the iMAC I have is fast for most things and more than enough for 99% of the population) but to not allow us to pop open the computer and make a quit upgrade to the machine is what really makes me feel like I'm using a computer built for Grannies. I mean there is a reason my mother loves iMacs and Iphones. Amazing that I was able to upgrade my memory from 4 to 16GB but I've heard Apple has even done away with that. I get why they do it. Apple Warranty, Apple Care issues, Profit and World Domination: Apple wants a monopoly on everything.
Was great to see Adobe bounce back after the whole Flash/HTML5 thing and knock Final Cut Pro off the face of the Earth for good. People are still buying it b/c of the brand name but Final Cut is done. David Fincher used Adobe's Workflow for everything when he made The Girl with The Dragon Tattoo. Hollywood is making the shift and the world will follow. The Adobe Workflow has finally come together and there is just no way Apple can compete with Adobe Creative Cloud and an Engine that can just swap from Premiere to After Effects to Prelude to SpeedGrade to Photoshop to Story with speed for $29 bucks a month(or $49 for some). Apple better start supporting Adobe's Mercury Engine or they may have a problem. And if you're using Final Cut X, you're severely handicapping yourself. Problem is that people don't want to take the time to learn Adobe's products(steep learning curve for sure) which is where Apple's Granny software, and perhaps computers, comes in to play. Arnold Schwarzenegger once said "Milk is for babies, Real Men Drink Beer". I'm beginning to think that "Mac's are for Grannies, Real Men Use Adobe and PCs".
The major problem with Apple is you're forced to use Apple. Not sure but history has proven that people don't like to be forced into anything. Autocracies don't work. These systems eventually topple, even in the corporate world.
Amazon.com, now that's the company to emulate. What an amazing machine!
I've read that Apple may even discontinue the iMAC after 2013. Who knows?
If anyone has a solution for getting the Mecury Playpack Engine GPU acceleration to work with Premiere Pro CS6 on an iMAC 2011, please let me know. Like I wonder if you could Thunderbolt an External graphics card somehow? Or is an upgrade possible? Ahh...not worth the risk.
1) Graphcis Card - AMD Radeon HD 6970M 2048 MB (6990 would have been better or something from NVIDIA.
2) USB 2.0 Hub with only 480 Mb/sec
3) Seagate Baracude SATA I 7200 RPM drive with 3GB/s transfer rate and only a 32 GB Cach. It's ok. I would have expected at least a Western Digital Caviar Black 2 TB SATA III 7200 RPM 64 MB or the Velociraptor at 10,000RPM.
4)APPLE SSD TS256C Flash Drive. As you can see, it doesn't stack up so well against other SSD Drive.
Just average. http://www.harddrivebenchmark.net/hdd_lookup.phphdd=APPLE+SSD+TS256CWhining and ranting about how iMacs can't do this or iMacs/orMacs can't do that is not going to get you a lot of help here.
Your "I love my MAC" is typical of the ever ubiquitous PC whiner.
If your video work needs were that computer intensive and critical , you should've done some online research and you should have budgeted for a Mac Pro.
Mac Pros are completely expandable and upgradeable unlike the iMac.
Mac Pros have much more faster and more CPU cores than the iMac line.
iMac line is limited to CPUs with 8 cores. The Mac Pros, I believe, are up to 16 core CPUs, now.
The Mac Pros can have their GPU upgraded and you even add/expand to use specialty audio/video cards.
Mac Pros are the defacto standard for real video work.
iMacs, even the high end model, is not really designed to do really heavy and intensive video work.
iMacs do do video creation and editing. Just not on the level that is needed from a more "Pro" computer.
It seems to me you are asking your iMac to do more than it was originally designed for, in terms of professional video editing.
You get a lot more out of a Mac Pro than an iMac for any real serious video, CGI or animation work.
You just didn't want to spend that much cash on one.
iMacs are not user upgradeable or friendly to user upgrades at all!!!
If you purchased a Mac Pro, you could've had that better, faster HD, better faster SSDs.
That said, I can offer no real help to but because of the nature of your post and the fact you just simply annoyed me, I feel some advice and explanations are in order
First off, you picked Adobe video editing software suite as your video creation software on the Mac. It's no secret to long-time video content creators on the Mac that Adobe products, especially those for video creation and editing are very user unfriendly on the Mac. Even though Macs are supported from Adobe, Adobe for a long time has treated the Mac and Mac users as second class citizens.
Before purchasing and installing Adobe Premiere, did you even check Adobe's site for the preferred system hardware and software requirements? Hmmm?
This is why you should KNOW what software you are going to be running on a computer first then research what computer make and model will run said software.
That's why Apple has its own apps like Aoerture, Logic and Final Cut.
Despite your ignorance in this matter, Final Cut Pro X is alive and doing well, thank you, and using this software on your iMac would kick Adobe Premier in the you know whats.
Final Cut Pro X is a complete video solution for and completely designed around the Mac.
Why are you using USB 2.0 connections for video work when you have a perfectly good FireWire 800 connection.
In case you are not aware, FireWire 800 is called so because it has a max throughput of 800 Mbps.
Your 2011 iMac can take up to 32 GBs of RAM. Not just 16 GBs.
This changed when the 2010 model iMacs came out.
Blu-ray? I believe you can buy external Blu-ray writers that work with Mac using said FW800 connection.
So you cite one movie and one videographer using Adobe Premier for your premise that Final Cut is dead in Hollywood?
Your argument that Apple locks you into everything in their world can be countered by saying Windows and Windows PCs lock you into the Windows world. What's your point?
Apple is not discontinuing their computers platforms any time soon.
All you are regurgitating is rumor. Probably from all of the PC crowd.
iMacs and professional desktop Macs are not going anywhere.
Currently, Apple is the only desktop/laptop computer maker that is still making a profit on their Macs and increasing their market share percentages for the last 5 years during which the PC market has continually slumped/dropped in its market share. -
Mp3 and j2me supporting reliance mobile
hi,
if anyone know abt mp3 and j2me supporting Reliance phone in market.if so please give me the link where to get teh details I already checking it with reliance website and i want more information please help me.
thanx in advance
laxmihi laxmi
i dont know did you check this URL
www.dadp.com
there is one forum also avail for the j2me and realience phone you will get all the information tehre
regards
[email protected] -
Windows Vista 64 Bit and Button Support - Qosmio G30?
Windows Vista 64 Bit and Button Support?
Everybody claiming that Vista x64 (or Ultimate) can't be used with FN keys or Flash Cards is utterly wrong!
I have a Qosmio G30 running Vista x64 Ultimate, and have both FN keys, Toshiba Flash Cards and (partly) the hardware buttons at the top working.
After a lot of research, I found that Toshiba has released a 64-bit version of VAP called util_tvap_27581D. If you google it, you might discover it... -
I Purchase iPad mini retina screen on July 7 2014 at Malaysia local apple sale agent switch store somehow now my iPad did restore to latest iOS 7.1.2, before that and after also facing 1new issue is my iPad mini cant success download apps and error message show can't download at this time, either retry or click done. My internet is good condition no line down, I reboot my iPad only can download but sometime can't need to reboot twice only can download. Very sad local sale and tech support can't help to solve my problem...
Reset the device:
Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.
If that doesn't help, tap Settings > General > Reset > Reset All Settings
If that doesn't help, tap Settings > General > Reset > Reset Network Settings
You will have to re enter your Wi-Fi password.
No data is lost due to a reset.
If nothing above helped, try here > iOS: Troubleshooting Wi-Fi networks and connections -
MacBook Crash and Apple Support
Not sure if anyone else has had this experience. First, I am a brand new Mac user. Bought the new MacBook Pro i7 with 8GB of RAM as a switch from my PC laptops.
Any other big crashes out there? Just wondering if there is a systemic hardware issue?
I had the new laptop for a total of 4 days before it crashed hard. on the first full day of use, it started crashing with the veil of grey and the message that a serious error had occurred and I needed to hold down the power button to restart. It crashed a total of 6 times in 4 days (2 days of real use) before I could get to the Genius Bar.
They stated that was obviously not normal and that I should request a new unit from AppleCare, which I did as an advanced replacement. I was hoping to keep my crashing laptop just to get more used to the Mac. However, after the Genius Bar did an archive re-install, the computer immediately crashed twice while in the store.
We then attempted to do an Erase and Install, and the unit would not install the fresh load of Mac OS X. The Genius Bar rep said it definitely looked like a hardware issue since it would not re-install the software, so I had to send the unit back ahead of receiving a replacement.
As for customer service, there was absolutely no urgency to get a replacement laptop to me. It was a customized unit and it is finally due to arrive today, but it has taken 10 days since I ordered my advanced replacement.
I will tell you that this has been a very frustrating and disappointing start to my Mac usage. And customer support could have made that bad experience so much better, but their lack of action and mis-statements actually made it worse.
Sorry, I was hoping for a much better experience. I am still hoping that IF the second MacBook works I can see that I made the right decision.
LewieEHi A Brody,
Lemons do happen and while that was a disappointment, the Genius Bar guys did a great job. I will say my expectations were higher for Apple based on everything I heard trying to make my decision to swap from a PC.
The first customer service rep I spoke to when I setup the advanced replacement stated that this unit would be put at the head of the que as it was a replacement for defective unit. The second rep I spoke with said advanced replacements have the lowest priority and it should have been returned as a zero dollar replacement and by him changing it to that, especially since my return unit had been received, would cause it to jump to the head of the shipments. The third person I spoke to said it just had to be processed in the normal 5-7 day shipping replacement and there was nothing they could do.
When a customer has a problem, customer service can make or break that experience. In fact, customers that have had a problem and had a positive resolution to that problem are shown to be more loyal than customers that have never had a problem at all.
Regards,
LewieE -
You have to love HP products and their customer service and technical support
My daughter has one of your ZV5000 notebooks. She has been very happy with it until the last few months when she started having charging issues. After investigation I found out that HP had a class action suit over this very problem. I called customer support and I emailed customer support trying to get HP to live up to it's obligation and fix it. I got no where and after several hours I gave up. She decided to get a new notebook. She bought a Compact Presario CQ50-130US from Staples. When she got it home she tried to connect to my wireless router and couldn't. We called technical support and spend the following 2 hours trying to get it to connect. I spoke to several techs none of which knew what they were talking about. They would read step by step from some try this if that doesn't work try this directions they must have. If that wasn't bad enough we constantly had to ask for it to be repeated because we couldn't understand them. They spoke English but with such heavy accents you couldn't understand what they were saying. The last tech was going to call Comcast my internet provider. I told him they provided the internet service not the router. He couldn't understand that. After keeping me on the phone for 15 minutes he came back to say he couldn't get threw and would call me back when he did. There customer service must be as good as yours is to get threw to. I got a call 24hrs later to ask if everything was alright. They never fixed the problem how could it be alright? By then she had decided to return the new one and buy a product other than HP or Compact. I would up fixing her old laptop something HP should have paid for but didn't. I have always trusted and respected the HP name. I am very sorry to see what it has become to stand for. Inferior products that you don't stand behind and customer and technical support that can't speak English and don't have a clue as to what they are doing. How sad! Do you think any of my family or friends will be buying an HP product?
well, this IS a means of finding a resolution for some issues. so why SHOULDNT they read this forum? i can assure you that there are people who are not just reading stuff off a book or a document. in fact, that is the biggest cliche's that exists today.
Make it easier for other people to find solutions, by marking my answer with \'Accept as Solution\' if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"
I am an ex-HP Employee. -
Migration and SAP Support for BW 3.1
Hi,
I have couple of queries regarding Migration and SAP Support.
What is the required patch level that need to be mantained in BW 3.1 for a direct upgrade to BI 7.
I would like to know whether SAP still supports BW 3.1. I searched in SAP Service marketplace, but didn't get much information regarding this.
Your inputs are highly appreciated.
Regards,
HariHello,
BW Upgrade from 3.x to 7.0
http://www.sdn.sap.com/irj/scn/index?rid=/library/uuid/e62b9990-0201-0010-42a7-ddcf5c93cafd
Hope it will help you.
Regards, -
Problem with installing Photoshop elements 9 and adobe support advisor
Hi, I've received a graphic tablet with 2 programs: the first has been downloaded and works perfectly while the second, PSE9, has been giving me problems for at least a week!
I downloaded it and now I have a winzip file full of strange things (one of this is set up exe which tells me that I have to install adobe support advisor) and two files which said 3DF.tmp and PSEP9(1).zip.download and if I try to click them they tell me that I have to find on the Net the program to open them because I can't. And I don't know which program is required.
I tried a lot of times to download the adobe support advisor, I have enough space on my disc and my farewall is deactivated, but when the program begins I saw this annoyant message
cpsid_82829s5 Missing installation file bootstrapper error occured
with this code for a support from adobe 00-67325-032018052012
I unistalled it and retried, but nothing.
Please, I just want to use my tablet with the programs which are comprised in the package, why it's so difficult to download this damn photoshop elements 9????????????
Thank youIn the error message it doesn't tell me
"Installer has detected that a machine restart is pending. It is recommended that you quit the installer, restart try again,"
neither "Installer failed to initialize. File not found. Please download Adobe Support Advisor to detect the problem."
and I have enough space and I have Windows xp then I should be able to install it. I tried to unistall and install again the support advisor but nothing. I'm desperate.
Messaggio originale----
Da: [email protected]
Data: 18/05/2012 22.20
A: "Questionlady"<[email protected]>
Ogg: Problem with installing Photoshop elements 9 and adobe support advisor
Re: Problem with installing Photoshop elements 9 and adobe support advisor created by Jeff A Wright in Trial Download & Install FAQ - View the full discussion
Did you try the steps listed in http://helpx.adobe.com/creative-suite/kb/troubleshoot-error-messages-b ootstrapper-cs5.html which was identified by the Adobe Support Advisor? If so can you please list each step and the result of those steps. This will allow us to best advise you on your next steps.
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4420419#4420419
To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4420419#4420419. In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Trial Download & Install FAQ by email or at Adobe Forums
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746. -
Payment withheld and customer support unable to help
My payment for about $4,000 was withheld this month because of an outstanding $30 app ad campaign balance.
The balance exists because my bank issued me a new credit card, replacing my old credit card on file. Ok, fine, I assumed I can pay the balance and have my payment issued, right? Wrong, the problem is that there is no way to pay the balance. I was finally
able to add my new card as a payment option but even adding the new card as a payment option does nothing; the ad campaign remains unpaid and no payment can be issued.
I've created support tickets and customer support has been unable to resolve this issue, with no end in sight. What few responses I've received from customer support all read the same way: "we are investigating the issue but have no updates for you
at this time". Meanwhile I fully expect my next month's payment to be withheld as well, because the outstanding balance is still there.
Has this happened to anybody else? If so were you able to resolve this? I find it hard to believe I'm the only one who has an outstanding balance for an app ad campaign.
I am half-hoping that somebody higher up reads this who has the authority or resources to help with this. I'm amazed there is no solution for this after weeks. I am simply out of options, I have no idea what can be done about this.Hello Nate,
You might not be able to create a new campaign in the payment failed state, but you can go to campaign creation page, add a new credit card and select the same. This will change the credit card associated with your account. If the card is good for swipe,
the account will be unblocked during the next monthly swipe cycle.
Please do so before the end of this month, so that your accounts get unblocked before the next payout cycle which is usually in the first week of every month.
If you have other feedback, please do let us know at
[email protected]
Thanks,
Vikram -
RSPOR_SETUP = Different ABAP and Java support packages.
Hi all,
We have an ECC 6.0 system with abap+java stacks. When we run the RSPOR_SETUP report we get this error:
Different ABAP and Java support packages. Combination of support packages invalid
And with some more clicking we find this:
6. Compare version information of Java support package (com.sap.ip.bi classes) with ABAP support package (SAP BI)
ABAP Support Package: 13
Java Support Package: 0
On the Java stack we see (among others) these components:
sap.com BI-IBC 7.00 SP12 (1000.7.00.12.0.20070509050058)
sap.com BI_MMR 7.00 SP12 (1000.7.00.12.0.20070507084106)
sap.com BI_UDI 7.00 SP12 (1000.7.00.12.0.20070507084125)
sap.com BI-BASE-S 7.00 SP12 (1000.7.00.12.11.20080324092518)
sap.com BI-WDALV 7.00 SP12 (1000.7.00.12.1.20071105133039)
sap.com BI-REPPLAN 7.00 SP12 (1000.7.00.12.3.20080104101916)
So I believe all components are correctly installed.
What are we doing wrong?Hello.
Please be aware, that report RSPOR_SETUP should NOT be used with a Netweaver 04s system. This report has been replaced by the support desk tool. I request you to run the support desk tool as per note 937697 to check if there are any configuration issues in your system.You can resolve any red traffic lights that might be reported by the tool by following the corresponding actions suggested.
I hope I can be helpful.
Thanks,
Walter Oliveira. -
Hello, I am a user of the iPhone is not the place for bi çıkıcak turkey apple brand products and product support and equipment does not work as it used to fix and send back waiting for your help. Please support me in this regard quit
We are all iphone users just like you.
Do you have a question for fellow iphone users?
Maybe you are looking for
-
Itunes was working fine. Tried to install latest upgrade and get error message about an invalid character in the path "Program Files (x86)". PC, Win7, nothing else appears to be having same issue. Program still works, simply cannor upgrade.
-
Hyperlinks in a scrollable frame moving on scroll
Context: Application for iPad, created in inDesign with DPS. Situation: We have a table inserted into a vertically scrollable frame. On top, we have a series of links that correspond to the table text (please see screenshot below). Problem: When the
-
Decode Vs Case: context switching?
So I was told recently that among other reasons, CASE is "better" than Decode in SQL statements because Decode context switches to PL/SQL to perform the checks. I can't find anything in the documentation to support this. this site here: http://www.db
-
Java Update Release 1-Install Process Freeze
On downloading Java Release 1 for Mac OSX 10.5, after downloading, I was prompted to enter my user password for a second time. As of now 'CONFIGURING INSTALLATION' has been frozen for over an hour with no movement on the progress bar. Contemplating a
-
Wls1033_oepe111150_win32.exe vs. server103_win32.exe
We're working on upgrading from weblogic 9.2 to 10.3. So far it's gone pretty smooth until this morning. I notice in the wls1033_oepe111150_win32.exe install package, there was no workshop IDE present...weird. So I went on a search for the latest wor