Catalyst 2948G: boot error

Does the following indicate a hardware problem? Can it be fixed? Please advise. Thanks.
This is the output when the switch is powered on and enters the "loading diagnostics" phase.
Loading diagnostics...
Power-on-self-test for Module 1: WS-X2948
Status: (. = Pass, F = Fail)
processor: . cpu sdram: . temperature sensor: .
enet console port: . nvram: . *** ERROR *** ttl=1 addr=70001210
expected=0000000000000242 actual=0000000400000242
*** ERROR *** ttl=2 addr=70001230 expected=0000000000000246 actual=0000000400000
246
*** ERROR *** ttl=3 addr=70001250 expected=000000000000024a actual=0000000400000
24a
*** ERROR *** ttl=4 addr=70001270 expected=000000000000024e actual=0000000400000
24e
*** ERROR *** ttl=5 addr=70001290 expected=0000000000000252 actual=0000000400000
252
*** ERROR *** ttl=6 addr=700012b0 expected=0000000000000256 actual=0000000400000
256
switch sram: F
switch registers: . switch port 6: F switch port 7: F
switch bandwidth: .
Module 1 Failed
After the switch boots, I get the message to: Use 'show test 1' to see results of tests.
Console> (enable) show test 1
Module 1 : 0-port Switching Supervisor
Network Management Processor (NMP) Status: (. = Pass, F = Fail, U = Unknown)
Control Processor Status:
DRAM : . EEPROM : . FLASH : . NVRAM : .
SX1000:
Register : . Network Memory : F
Mgmt Port Loopback Status: .

This is definitely a hardware problem. Appearently, your only hope is that it's a temperature related problem.
Therefore you could try to take the module out and remove the dirt from the last years. It might give your switch some more air and reseating the connectors isn't that bad either. If it doesn't help, please keep in mind that eventually we all pass away! ;-)
Regards,
Leo

Similar Messages

Share FCPX with Blu-ray USB3 LaCie writer boot error

Hi
I've been around the bush and back looking at how to burn a blu-ray movie to a disc from FCPX and a slim Blu-ray LaCie drive. I was able to burn a 5 minute movie from FCPX without any trouble but as soon as I try and burn something larger (like an 11gig movie) 1080 HD I get up in the morning to find an error referring to boot directory or something with a boot in it. Sorry can't be more secific than that. It's costing me everytime it goes wrong.
I logged a job with LaCie and they said any disc is compaitble so i'm wondering whether there is an issue with Final Cut Pro X ? Thank you for any assistance.
Mike

OK, I have FCPX. I burned DVDs etc all fine. I then burn a Blu-ray. Initially I tried to save to hard drive and burn from there but that didn't work. Seeing FCPX can burn directly to optical device (LaCie) I tried that (share menu in FCP) I got a boot error message that I didn't take a note of. Today I tried again after I checked a few things out. I put in my BD-R disc into the device. FCPX says it is "finishing create blu-ray disc: burning Blu-ray"
at 85% it then said Insert Disc, i did this and it is hanging.
I have been able to burn a 5 mintue Blu-ray sucessfully but as soon as I get to a 55 minute movie I have been unsuccessful. Layers are automatic. speed is automatic, it's a brand new mac running OS X 10.8.2 The guy I bought the discs from reccomends Roxio but why should I buy new software when FCPX says it burns.

Boot Error Sequence

IdeaCentre K210 57078894 works fine until I completely shut it down and restart it. I get errors like Boot Error Sequence, PXE-E53 No boot filename received, PXE-M0F. When I go to the BIOS setup it says Primary IDE not detected. Can anyone help fix this problem?

Hi,
You might try removing the hard drive and then put it in an external 3.5" USB enclosure and then test it on a different PC. This type of adapter could also be used to test the hard drive on another PC.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

Some boot error

I am getting some boot error at the very end at boot time and it moves to fast for me to catch it.
I did try with read -n1 added to rc.conf but as the error is at the very end so it just jumps past the error.
I had a look in /var/log files but could not really find anything.
Where to find the boot log? Or something else?

cell wrote:I did try with read -n1 added to rc.conf but as the error is at the very end so it just jumps past the error.
You should add read at the end of /etc/rc.local

[Solved]Syslinux "booting... boot error" when booting Windows 7

Hello, I've set up my computer to dual boot windows and arch. Windows is on a separate hard drive and I was able to configure syslinux with a boot menu allowing me to select Windows at startup. For a long time this has worked without any problems whatsoever, but this morning I tried selecting windows and I got what is probably the most vague error message I have ever seen.
"Booting...
Boot Error"
According to this post this problem comes in when the ldsyslinux.sys file cannot be found. Unfortunately I was not able to use his suggested fix
syslinux -U /dev/sdb1
I wasn't aware that there was a -U flag for syslinux and after checking it seems that there isn't one.
Last edited by samstr (2014-11-26 04:48:55)

Sorry, I actually just fixed it on my own, it turns out my BIOS settings were a bit... weird. For some reason I didn't have my windows drive listed and it tried to boot a USB drive I had plugged into my computer. I just had to fix the drive order and it worked fine. Sorry about starting a fairly useless discussion.

Compaq CQ62-215DX-fan boot error, even after fan replacement

I have a Compaq CQ62-215DX laptop. Everytime on startup I get this boot error "a system fan is not operation correctly" The system then automatically shuts itself down after a few seconds.
I ordered a replacement fan and installed it, however I'm still getting the same issue.
I figure the chances of the newly installed replacement fan being DOA are fairly low, so what should be next step to fixing my problem? Are there any common problems with the replacement of these fans on this particular computer? The laptop is a few months out of warranty so I'm either stuck paying a bunch of money to fix it, or buying a new computer if I can't fix it myself. Help!

It's either a bad fan which I agree is unlikely or a bad fan header on the motherboard which means a new motherboard. Sorry.

Hp Pavilion a6863w getting disc boot error..can't get windows vista to open...need help diagnosing

My computer will not open Windows Vista.. I get a disc boot error. I have run a few diagnostics but need help to preceed. Have important files on the computer I need access to. Can anyone help walk me through the process? Thanks Also when I look at the check s that have been done it says something about a registry problem. HP Pavilion a 6863w
{Edited for privacy}

Have you run a Hard Drive test in BIOS?
Jennifer P
I work for HP.
Please select the "Accept as Solution" button on the post that best answers your question. Also, you may select the "Kudos" button on any helpful post to give that person a quick thanks

"NI-488 boot error: OpenMarkedDrivers failed"

The GPIB card was working on wednesday, then Friday it was giving me the error "NI-488 boot error: OpenMarkedDrivers failed". I've tried installing an updated driver but nothing works. I don't know if it is a problem with the software or the GPIB card itself

Hi,
What OS and driver version are you using? When exactly does the error show up?.
I only found one (old) reference to this error.
DiegoF
National Instruments

Serious boot error. very annoying. P6NGM mobo. NVIDIA mcp73 chipset

Serious boot error. very annoying. P6NGM mobo. NVIDIA mcp73 chipset
I have a 80gb Western Digital that i installed xp on using another computer but it still wont boot nor will the cd drive boot even with a 100% original valid windows installation disc.
No matter what I do I always get the stupid "Reboot and Select proper Boot device or insert Boot Media in
selected Boot device and press any key."
At first i thought the motherboard was fried so i sent it back and had it replaced. Put it together, booted it, still the same problems. I have the hard drive set as master drive and it has windows xp installed but it still wont boot from it. please assist
System is:
# Intel Core 2 Duo E6750 Conroe 2.66GHz 4M shared L2 Cache LGA 775 65W Dual-Core Processor
# P6NGM Motherboard (MS-7366)
# 1GB RAM
# Onboard NVIDIA MCP73 Series Chipset
# Western Digital Caviar SE WD800JB 80GB 7200 RPM 8MB Cache IDE Ultra ATA100 Hard Drive
# Windows XP SP1 already installed on the hard drive using another computer
# 400W Power Supply

Take attention to WD jumper config:
Jumperless = Standalone
Jumper master = Master with Slave
Jumper slave = Slave with Master
Leave WD drive alone in the channel and remove jumper from the drive:
Make sure that IDE cable is connected in correct direction, (blue to mainboard and black to HDD in a picture below):

GE60 0NC booting error

Hey guys my GE60 0NC seems te have some kind of issues.
When I boot it and logg in the booting seems to stop at the WiFi connecting.
At that moment I can start a few minor programs but a lot of booting hasnt been finished yet.
To fix this I tried to:
-Systemrepair it to 1 day ago
This seemed to help, I could use it again although it ran a lot slower than normal.
In addition some programs seem to have some error, for instance League of Legends won't boot.
However when I shut it down and rebooted it again I was back to the same booting error.
What could be the problem here?
Thank you very much for your time.
Olav

I've been having the same problem for over a week (MSI GE60 - i5-3210M, 6GB RAM and GT650M; bought a bit over a year ago).
It started with a normal boot, but when I logged into my account I couldn't start any programs for 5-10 minutes. My S-Bar also stopped responding and crashed.
At first I suspected malware/virus, and actually found some shady files that I deleted with Malwarebytes Anti Malware.
The problem was still there though, so I did a system restore (I couldn't go back more than a few days) and that seemed to fix the problem - but after a reboot it was back.
I could find some errors, like the one you linked, in the Event Viewer - but also alot of Information-events from NvStreamSvc (several every sec) which is a part of Nvidia.
So today I uninstalled GeForce-experience (couldn't launch it apparently, got some error) and then installed an older display driver 310.90.
I also reinstalled my S-Bar and now it seems like I run pretty decent. The WiFi-logo has gone back to normal and I can start up programs early after a boot.
You could also try and uninstall some recent Windows Updates - I'm not sure if they're involved, but you could always give it a try.
Hopefully this helps you, or someone else, in some way.

BCD/boot error 0xc0000001 ~ stuck on broken windows partition

Okay so I have a macbook pro 2009 and I recently partitioned my hard drive to get windows 7 premium using bootcamp. While installing new software for my windows side it it froze up and I had to do a hardshut down. After I restarted my computer it came up with a black screen that says boot/bcd error - 0xc0000001
info: an error occurred while attempting to read the boot configuration data.
It instructs me to
1. insert your windows installation disk and restart my computer
2. choose your language settings and then click "next"
3.click "repair your computer"
problems I've come across while attempting to fix this
1. when selecting what operating system to repair after starting up the windows installation disk there are no operating system that shows up.
2. "repair your computer" option does not work and cannot repair the problem.
3. cannot hold down option to go back to Mac side because of EFI lock which I don't know the password to it.
4. cannot get to safeboot for reasons unknown, but holding down f8 doesn't work and holding down FN with F8 also does not work. It just goes to the boot error screen.
5. System restore does't work either.
6. went into command prompt and typed sfc / scannow but it says that another scan is in progress but needs to reboot to start. Every time I restart the same message pops up.
All I really want to do is get back to my mac side so I can delete the partition at this point. But it is IMPOSSIBLE so if anybody knows any solutions please do share. thanks!

Hi electrovalent,
I agree with Tripredacus,we seem to miss the important part that we should boot from the UEFI mode for a GPT format disk.To boot from the UEFI mode:
1.Insert the installation DVD or USB flash drive, and boot the computer.
2.When the firmware starts to initialize, press the key that opens the UEFI firmware boot device menu, such as Esc, F2, F9, F12.
3.Select an EFI drive, examples: EFI DVD/CD Drive, EFI USB Drive, or EFI Network Drive. You may be immediately prompted to press a key to boot from the drive to continue.
Here is a link for reference :
Walkthrough: Boot Windows PE from a UEFI-based Hard Disk
https://technet.microsoft.com/en-us/library/hh265131(v=ws.10).aspx
I have noticed you have tried the "Startup Repair"option before but I would suggest you try this option again .Because we have chosen the UEFI mode this time and this option is usually useful and convenient to repair the boot loader.
If the issue persists ,try the following command line .I also noticed you have tried the similar command line before but I have made a little modifications according to the screenshots you have posted.
diskpart
list vol
sel vol 2 (Volume 2 is the fat32 volume,this step is not included in the screenshot )
assign letter=v
exit
ren BCD BCD.old (Backup bcd )
bcdboot c:\Windows /s v:
Best regards
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
[email protected]

648 Max Boot Error

Hope someone can help...
I have just built a computer on the 648Max Motherboard.
My problem is, on first boot, the BIOS detects all hardware ok, but on re-boot, it fails after the MSI splash screen to find them and has a "boot error" on each, then asks for a boot disk in the FDD but this doesn't work either.
The "D Bracket" shows all four lights green.
I have checked all the connections countless times, even taken it back to barebone with no luck. I've checked the Hard Drive in an older computer and boot up fine into Win98.
I have no clue what else to try, the system spec is :-
P4 2.4Ghz
684 Max Motherboard
Xabre 128Mb DDR Ram Graphics
2x512Mb DDR Ram PC2100 Memory
128Gb IBM Deskstar 180GXP HDD
TEAC CD-W54E CDRW
Samsung DVD8E DVD
Windows 98SE
Thanks...
?(

Whipsnade...
Yes, i have tried other IDE cables that i know work fine.
Nope, i wasn't able to install windows, the hard drive was taken out of my older computer with it already installed which was working fine, and still does if i put the hard drive back.
All i have been able to do on the new computer is power up into BIOS, that's it...
The PSU i have is a brand new 350W which came with the case.
The hard drive does spin up yes...
Andy2
Yes, the hard drive is set to master and is in the primary connector on the board, its a working drive from a previous system...
Rob454
I've re-checked and i'm using a couple of older ide cables i know are ok, they actually have printed on them "board", "master and "slave"
Thank you all for your help, but i just don't know what to do with it now...
?(

Windows boot error 0xc00000e9, 0xc0000098 in Lenovo U400

I've been getting boot error in my 8 month old Lenovo U400. No changes were done in hardware or software. It says bootbcd file is missing. Doesn't boot through hardware, but boots just well when I go to advanced boot menu and select the SSD option. The functioning of the laptop seems to be just as good, fast and there's no problem whatsoever after I boot through this. Then why doesn't it boot normally? Why does it say it could not find a valid OS entry??
I tried resettting the boot file. During the process I noticed that the partition with the OS is marked hidden and is a RAW partition, rather than NTFS. Since this error, I haven't been able to use Lenovo one key recovery either. I have never reinstalled/formatted a system with SSD, and am not quite sure if a clean reinstallation of Win OS would help.
What should I do?

The moment you selected your drive to boot from start pressing F8 button, it should show you some extra boot options, where should be a repair option. Go there, it might ask you login, then there will be option to fix startup problems.

Boot Error 501 QuickWeb

My QuickWeb won't work.When ever I open by pressing the dedicated key it says Boot Error 501 BIOS Corrupt/Missing.
How to fix that error.
I have a Recovery Hard Drive (D and HP_Tools (E with one backup in with which was before I had deleted the previous User Account and all files associated with it. Which shall I use?
And if I use E will all my previous files come back? I do not want that .
Also, I have heard that pressing Windows+B and then powering it up does the trick.Will that work? What will be used ? D or E?
All , my previous files will be restored? I don't want that.
Please help.

Refer:
http://support.hp.com/us-en/document/c03738933
Wish you luck,
Karthik
--Say "Thanks" by clicking the Kudos (purple thumbs up icon in the lower right corner of a post)
--Please mark the post that solves your problem as "Accepted Solution"

Cisco catalyst 4506-e boot error

Rommon signature verification PASSED for golden image
Rommon signature verification PASSED for primary image
FPGA signature verification PASSED for primary image
* Welcome to Rom Monitor for WS-X45-SUP7-E System. *
* Copyright (c) 2008-2011 by Cisco Systems, Inc. *
* All rights reserved. *
Primary Rom Monitor Version 15.0(1r)SG5
CPU Rev: 2.2, Board Rev: 10, Board Type: 101, CPLD Moka Rev: 7.0x3718.0xb565
Chassis: WS-C4506-E
Got Mac Address: c0:67:af:40:24:c2
MAC Address : c0-67-af-40-24-c2
IP Address : 14.18.2.234
Netmask : 255.255.255.0
Gateway : 14.18.2.21
TftpServer : Not set.
Peer supervisor not detected or is not running IOS
Supervisor uplinks and all linecards have been reset
***** The system will autoboot in 5 seconds *****
Type control-C to prevent autobooting.
******** The system will autoboot now ********
config-register = 0x2101
Autobooting using the first file from bootflash.....
loading image
Checking digital signature
bootflash:/cat4500e-universal.SPA.03.05.02.E.152-1.E2.bin: Digitally Signed Release Software with key version A
Rommon reg: 0x00004F80
Reset2Reg: 0x00000F00
Image load status: 0x00000000
Snowtrooper 155 controller 0x044DDBD2..0x04688FA7 Size:0x0041DCD4 Program Done!
[ 57.324367] pci 0000:00:00.0: ignoring class b20 (doesn't match header type 01)
Starting System Services
Calculating module dependencies ...
Loading rtc-ds1307
RTNETLINK answers: Invalid argument
No Mountpoints DefinedNov 13 09:35:24 %IOSXE-3-PLATFORM: process sshd[4211]: error: Bind to port 22 on :: failed: Address already in use.
diagsk10-post version 5.1.4.0
prod: WS-X45-SUP7-E part: 73-14393-02 serial: CAT1837L75P
Power-on-self-test for Module 1: WS-X45-SUP7-E
CPU Subsystem Tests ...
seeprom: Pass
Traffic: L3 Loopback ...
Test Results: Pass
Traffic: L2 Loopback ...
post timeout
A Critical job [post] exited abnormally! Reloading the supervisor
Killed by signal [TERM]
Loading virtuclock as vuclock
Loading gsbu64atomic as gdb64atomic
Loading isp1362_hcd_k10
/dev/fd/13: line 273: /sys/devices/system/edac/mc/edac_mc_log_ce: No such file or directory
Starting IOS Services
AIPC Module Loaded...
cat4k-watchdog[6250]: Watchdog daemon initialized on 2 CPU(s)
cat4k-watchdog[6250]: Watchdog daemon started.
Dumping all the logs to /root/reload.20141113..Please be patient
All logs dumped
sysmgr: <<%SYSMGR-2-SERVICE_CRASHED>> Service "System Manager (parser)" (PID 6820) hasn't caught signal 15 (no core).
/bin/kill: 8178: No such process
/bin/kill: 8179: No such process
/bin/kill: 8197: No such process
/bin/kill: 8198: No such process
/etc/rc6.d/S01reboot: line 198: umount_cisco_filesystems: command not found
Please stand by while rebooting the system...
[ 266.041680] Restarting system.
Rommon signature verification PASSED for golden image
Rommon signature verification PASSED for primary image
FPGA signature verification PASSED for primary image
* Welcome to Rom Monitor for WS-X45-SUP7-E System. *
* Copyright (c) 2008-2011 by Cisco Systems, Inc. *
* All rights reserved. *
Primary Rom Monitor Version 15.0(1r)SG5
CPU Rev: 2.2, Board Rev: 10, Board Type: 101, CPLD Moka Rev: 7.0x3718.0xb565
Chassis: WS-C4506-E
Got Mac Address: c0:67:af:40:24:c2
MAC Address : c0-67-af-40-24-c2
IP Address : 14.18.2.234
Netmask : 255.255.255.0
Gateway : 14.18.2.21
TftpServer : Not set.
Peer supervisor not detected or is not running IOS
Supervisor uplinks and all linecards have been reset
***** The system will autoboot in 5 seconds *****
Type control-C to prevent autobooting.
******** The system will autoboot now ********
config-register = 0x2101
Autobooting using the first file from bootflash.....
loading image
Version: cat4500e-universal.SPA.03.05.02.E.152-1.E2.bin
Any help PLZ

config-register = 0x2101
Autobooting using the first file from bootflash.....
You need to provide more information. What are you trying to do? How many IOS file(s) do you have in the bootflash?
sysmgr: <<%SYSMGR-2-SERVICE_CRASHED>> Service "System Manager (parser)" (PID 6820) hasn't caught signal 15 (no core).
Break into the auto-boot process and post the output to the command "dir bootflash:".

Catalyst 2948G: boot error

Similar Messages

Maybe you are looking for