Catalyst 4006 with Supervisor Engine II Multicast Support?

Hi, I have a Catalyst 4006 with Supervisor Engine II. I would like to know if it is possible to enable multicast routing via CGMP or IGMP. I know it is possible with the Supervisor Engine III. Any advice would be appreciated.

Cat4006 wiht sup II runs a CatOS and it's stricly Layer 2 therefore it does not support any kind of routing (L3). It does support multicast services. Switches can use CGMP, IGMP filtering, or GMRP to dynamically configure switch ports so that IP multicast traffic is forwarded only to ports that are associated with IP multicast hosts.
Please refer to this link:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/8_3/configur/multi.htm#wp1019880
Please rate all posts.

Similar Messages

After upgrading ios Cisco Catalyst 6500 Series Supervisor Engine 2T to the latest release the ASA-SM module is not recognized

after upgrading ios Cisco Catalyst 6500 Series Supervisor Engine 2T to the latest release the ASA-SM module is not recognized it is disabled. the FPD
is not recognized any more. reverted back to previous ios with no luck

Duplicate post.
Being discussed actively in this thread.

After upgrading ios Cisco Catalyst 6500 Series Supervisor Engine 2T ASA-SM is disabled

after upgrading ios Cisco Catalyst 6500 Series Supervisor Engine 2T to the latest release the ASA-SM module is not recognized it is disabled. the FPD
is not recognized any more. reverted back to previous ios with no luck

What IOS are you running on your Supervisor 2T? As long as it's 15.0(1)SY1 or later you should be OK. (Reference).
If it's not working with that I'd try reload of the ASA SM module (from IOS cli - e.g. "hw-module <module#> reset" and, failing that, "no power-enable module <module#>" followed by "power-enable module <module#>) while the new Supervisor is installed. Watch the log for relevant messages during that process.

Supervisor Engine 8 Not Supported

Hi All,
Recently our customer has bought a new supervisor engine 8 for their catalyst 4507R-E chassis to replace the current supervisor engine 6l-e. The problem is when ever the chassis reload with the new supervisor engine 8, it appears a message stating some sort that this type of chassis is not supported by this supervisor engine thus the supervisor will shut down. When refer to the link http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/hardware/configuration/notes/OL_29676.html it stated there 1.The Cisco Catalyst 4507R-E Switch supports Supervisor Engine 8-E only on chassis that have hardware revision 2.0 or higher. Contact your Cisco customer service representative for more information. So then I have issued the show idprom chassis.
Chassis Idprom :
Common Block Signature = 0xabab
Common Block Version = 3
Common Block Length = 144
Common Block Checksum = 3909
Idprom Size = 256
Block Count = 4
FRU Major Type = 0x4001
FRU Minor Type = 52
OEM String = Cisco
Product Number = WS-C4507R-E
Serial Number = FOX1428H643
Part Number = 73-12778-01
Part Revision = C0
Manufacturing Deviation String = 0
Hardware Revision = 2.0
Top Assembly Number = 800-26494-03
Top Assembly Revision Number = A0
Power Consumption = 0
RMA Failure Code = 0 0 0 0
Chassis Block Signature = 0x4001
Chassis Block Version = 1
Chassis Block Length = 22
Chassis Block Checksum = 1167
Feature Bits = 0x0000000000000000
MAC Base = d0d0.fd85.15c0
MAC Count = 64
Clei Block Signature = 0x4601
Clei Block Version = 2
Clei Block Length = 26
Clei Block Checksum = 1142
Clei code string = IPMJ410BRB
Version ID string = V03
Clei ECI Number = 461486
SecSerialNum Block Signature = 0x4602
SecSerialNum Block Version = 1
SecSerialNum Block Length = 26
SecSerialNum Block Checksum = 773
SecSerialNum string = NWG1427026P
By right, this hardware revision is supported by the new supervisor engine 8. Idea anyone?
Thanks.

I think you need to upgrade the IOS-XE to 3.7.0E to be able to enable this feature.
Another thing, the Release Notes firmly states you need to upgrade the Bootstrap to SG5 in order to load 3.7.0E.
You can do this in just one reload with this process: Upgrading the Supervisor Engine ROMMON with Telnet

Cisco 4006 & 4506 sup engine

Hi,
My existing 4006 chassis is using Supervisor III (WS-X4014).
I have another 4506 chassis using Supervisor IV (WS-X4515) and a Netflow Services Card (WS-F4531) build on top of it.
I need Netflow Services Card in 4006, so can I just replace the Supervisor IV (WS-X4515) used in cisco 4006? Is it compatible with 4006?
Any suggestion?
Thanks,
HowYee

hi HowYee,
http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps4324/product_data_sheet0900aecd8035cf2b.html
according to that document, it is not possible if you want to put supIV to 4006 chassis
Chassis and Line-Card Support
You can deploy the supervisor engine IV in single-chassis nonredundant mode in the Cisco Catalyst 4503, 4503-E, 4506, and 4506-E chassis. You can also deploy it in single-chassis redundant mode as an option in the Cisco Catalyst 4507R chassis (slots 1 and 2 only) and Cisco Catalyst 4507R-E/4507R+E chassis (slots 3 and 4).
The supervisor engine IV is compatible with the classic Cisco Catalyst 4500 and the E-series Cisco Catalyst 4500 Line Cards. Table 1 gives performance information for the Cisco Catalyst 4500 Series Supervisor Engine IV.
regards,

Can 2 supervisor engine's ports both work at same time?

As I know that, when 1 supervisor engine is working, another engine's ports are totally down in redundancy mode .
Is there any way to let 2 supervisor engine's ports are both working at same time?

The two supervisor engines in a redundant supervisor engine configuration have different responsibilities. The active supervisor engine is responsible for controlling the system bus and all line cards. All protocols are running on the active supervisor engine and it performs all packet forwarding. The standby supervisor engine does not communicate with the line cards. It receives packets from the network and populates its forwarding tables with this information, but does not participate in any packet forwarding. The relevant protocols on the system are initialized, but not active, on the standby supervisor engine. The Cisco Catalyst 6500 Series supervisor engines are hot-swappable and the standby supervisor engine can be installed in a running, active system. Also please note that redundant supervisor engines do not perform load sharing. The active supervisor engine is providing the entire packet-forwarding intelligence for the system (N+1 redundancy). If the active supervisor engine fails, the standby supervisor engine can still maintain the same system load.
The standby supervisor engine polls the active supervisor engine through the Ethernet out-of-band channel (EOBC) every 5 to10 milliseconds to monitor the online status of the active supervisor engine. The active supervisor engine might go offline for a variety of reasons such as hardware failures, system overload conditions, memory corruption issues, removal from chassis, being reset by the operator, or real-time diagnostics-driven supervisor switchover (also known as Generic Online Diagnostics) 1. The standby supervisor engine detects this type of failure and becomes the new active supervisor engine. The Catalyst OS software on the supervisor engine is responsible for restoring the protocols, line cards, and forwarding engines to normal operation. This restoration takes place through a fast switchover or a high-availability switchover.
HTH

Cisco WS-4506-E Switch with Supervisor II (EOL, EOS)

Hello,
I have a Distribution/Access Switch Cisco WS-4506-E Switch with Supervisor II (EOL, EOS). when are the exact EOL/EOS dates and can only upgrade the supervisor engine to Supervisor 8?
Thanks

EoS/EoL: Cisco Catalyst 4003 Chassis, Supervisor Engine I & III

Catalyst 4006 latest software

Hi,
I have a Catalyst 4006, with moduels WS-X4013, WS-X4148-RJ, WS-X4232-L3 and WS-X4232-GB-RJ.
Can someone please let me know the latest firmware and IOS for this.
I've been told that the latest firmware is 8.4(7)GLX, but do not know what the latest version of IOS is.
Hope someone can help.
Thanks
Scott

For web interface, you will need the CV capable image in the bootflash in addition to the main 7.6(13) file.
You can download cat4000-cv.7-6-1.bin to the bootflash from the following page(CV image and the CAT OS image versions can be different)
http://www.cisco.com/cgi-bin/tablebuild.pl/cat4000
The following tech tip should help as well
http://www.cisco.com/warp/public/473/105_15954.shtml

Catalyst 4006 Supervisor Engine 3 - routing features

How to ensure the Supervisor Engine 3 module has been integrated into Catalyst 4006? Any command I can use to make sure this? I am going to use it to do all routing for a enterprise network.....

I do not understand your question. Sup3 for CAT 4006 runs IOS and can route EIGRP/OSPF/IS-IS with enhanced image and RIP/static routes with Basic image.

Catalyst 4006 chassis with CATALYST 4500 SUPERVISOR V

Hi Experts,
Can I use CATALYST 4500 SUPERVISOR V(WS-X4516) in an old 6-slot catalyst 4006 chassis( WS-C4006). I want to run the latest IOS available and I have the following line cards:
WS-X4232-RJ-XX
WS-X4418-GB
WS-X4148-RJ
thanks and regards
alex

Hi Alex
Yes you can run the Sup V in the 4006 chassis. See this link
http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/hardware/module/guide/01overvw.html#wp1015031
The Sup V also supports the WS-X4418-GB and WS-X4148-RJ modules - see attached link
http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps4324/product_data_sheet09186a00801fcaba_ps2797_Products_Data_Sheet.html
HTH
Jon

Does Supervisor Engine 6L-E compatible with Cisco Ws-C4506 Non-E switch?

Does Supervisor Engine 6L-E compatible with Cisco Ws-C4506 Non-E switch?

Yes, it is compatible with non-e chassis.
see below:
The Cisco Catalyst 4500 Supervisor Engine 6L-E is also compatible with classic Cisco Catalyst 4500 line cards, chassis (3-, 6-, and 7-slot), and power supplies, providing full investment protection.
link to data sheet:
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-4500-series-switches/data_sheet_c78-530856.html
HTH

Upgrade Catalyst 4500 Supervisor Engine 8-E(IOS XE Software)

Folks,
We are looking to upgrade the Catalyst 4500 Supervisor Engine 8-E(IOS XE Software). As of now we are running on 3.3.1XO and as per the Cisco notes version 3.3.2XO which is suggested version.
I would like to find some comparison documents on both these version and establish if there is a need to do the upgrade. What are the fixes that have been done in this version.
Thanks,!!

Hi Nikhil,
Please find release notes of version 3.3.2XO below which can provide you the details to upgrade.
Mainly you need to refer the features it supports and resolved cavets (which means the bugs resolved fro the earlier version on to this.).
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/release/note/OL_29983-01.html
HTH
Regards
Inayath
*Plz rate if this info is helpfull.

Catalyst 4006 Network Teaming with Linux server

hi ,
i need to setup network teaming and do ethernahcneel between
Catalyst 4006 & Linux server
i want to ask ,
does catalyst 4006 support lacp ???
if dont support lacp , does pagp cant be work if the 2nd side is not a cisco device ?? in my case "linux server "
regards

@CSCO12006413
Listen to ‘glen.grant’ – ‘pagp’ is propriety to Cisco devices, so your only option will be ‘lacp’.
However, my question to add to this post – would ‘CSCO12006413’ want to go with the MAC or IP Load-balancing methods? Question - If the destination address is the same, but source address different ‘CSCO12006413’ should use MAC based load-balancing; however, if this is for server-to-server configuration, I think you will want to use IP based load-balancing on the EtherChannel configuration?
Thanks
JJ

Monitoring dual core (Supervisor Engine 7-E) through EEM Script.

Hi,
I have a Cisco Catalyst 4500E Supervisor Engine 7-E and configured an EEM Script to monitor the dual core CPU Utilization through PRTG Network Monitor.
event manager applet dualcore authorization bypass
event timer cron cron-entry "* * * * 0-6"
action 100 cli command "en"
action 120 cli command "show process cpu | include five"
action 220 regexp "Core 0: CPU utilization for five seconds: ([^%]+)%; one minute: ([^%]+)%; five minutes: ([^%]+)%.*" $_cli_result result c0cpu5sec c0cpu1min c0cpu5min
action 240 if $_regexp_result eq 1
action 260 end
action 320 regexp "Core 1: CPU utilization for five seconds: ([^%]+)%; one minute: ([^%]+)%; five minutes: ([^%]+)%.*" $_cli_result result c1cpu5sec c1cpu1min c1cpu5min
action 340 if $_regexp_result eq 1
action 360 end
action 440 cli command "config t"
action 441 cli command "snmp mib expression owner cisco name c0cpu5sec"
action 442 cli command "expression $c0cpu5sec"
action 443 cli command "snmp mib expression owner cisco name c0cpu1min"
action 444 cli command "expression $c0cpu1min"
action 445 cli command "snmp mib expression owner cisco name c0cpu5min"
action 446 cli command "expression $c0cpu5min"
action 550 cli command "config t"
action 551 cli command "snmp mib expression owner cisco name c1cpu5sec"
action 552 cli command "expression $c1cpu5sec"
action 553 cli command "snmp mib expression owner cisco name c1cpu1min"
action 554 cli command "expression $c1cpu1min"
action 555 cli command "snmp mib expression owner cisco name c1cpu5min"
action 556 cli command "expression $c1cpu5min"
action 600 cli command "end"
end
It works fine but on the logging buffer there are a lot of %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:moncores) messages   -one per minute-   here an example:
Oct 29 17:54:01: %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:dualcore)
Oct 29 17:55:01: %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:dualcore)
Oct 29 17:56:01: %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:dualcore)
Oct 29 17:57:01: %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:dualcore)
I considered to use the logging suppress duplicates command to prevent the consecutive logging of more than one copy of the same system logging (syslog) message but it is only available to the Cisco IOS XR.
Someone could help me to determine if it is possible to avoid this messages through Embedded Syslog Manager, I tried to do that but
I was not successful.
Regards,
~Sergio

Hi,
I did transitioned CLI actions to the EXPRESSION-MIB SNMP but I could not receive anything information about the dualcore utilization on the PRTG Network Monitor and received a lot of %HA_EM-7-FMFD_SNMP_ERRCODE: fh_fd_snmp_errcode: Error status: 6 NO_ACCESS_ERROR: 1. messages on the WS-C4507.
Considering the initial EEM script, could ypu help me to avoid the %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:moncores)
messages using Embedded Syslog Manager.
Here some snmpwalk to validate that I could not get the OIDs to monitor both cores.
STEP 1     Only one value is given because there is only one physical cpu.
cpmCPUTotalPhysicalIndex
1.3.6.1.4.1.9.9.109.1.1.1.1.2
C:\usr>snmpwalk -v 2c -c m4nc4rc0 10.20.91.2 1.3.6.1.4.1.9.9.109.1.1.1.1.2
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.2.4000 = INTEGER: 4000
STEP 2
entPhysicalName
1.3.6.1.2.1.47.1.1.1.1.7
C:\usr>
C:\usr>snmpwalk -v 2c -c m4nc4rc0 10.20.91.2 1.3.6.1.2.1.47.1.1.1.1.7.4000
SNMPv2-SMI::mib-2.47.1.1.1.1.7.4000 = STRING: "Linecard(slot 4)"
#sh mod
Chassis Type : WS-C4507R+E
Power consumed by backplane : 40 Watts
Mod Ports Card Type                              Model              Serial No.
---+-----+--------------------------------------+------------------+-----------
1    18 10GE (X2), 1000BaseX (SFP)             WS-X4606-X2-E      JAE151904JC
2    24 1000BaseX (SFP)                        WS-X4624-SFP-E     JAE152001AE
4     4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP)   WS-X45-SUP7-E      CAT1522L0G1
5    48 10/100/1000BaseT (RJ45)V, Cisco/IEEE   WS-X4548-GB-RJ45V JAE12067N8K
M MAC addresses                    Hw Fw           Sw               Status
--+--------------------------------+---+------------+----------------+---------
1 e8b7.4880.e5db to e8b7.4880.e5ec 1.2                               Ok
2 e8b7.48cc.6167 to e8b7.48cc.617e 1.2                               Ok
4 4055.39d7.76c4 to 4055.39d7.76c7 1.0 15.0(1r)SG2 03.01.01.SG      Ok
5 001e.f7da.d290 to 001e.f7da.d2bf 4.1                               Ok
Mod Redundancy role     Operating mode      Redundancy status
----+-------------------+-------------------+----------------------------------
4   Active Supervisor   SSO                 Active
STEP 3
cpmCPUTotal1minRev
1.3.6.1.4.1.9.9.109.1.1.1.1.7
C:\usr>snmpwalk -v 2c -c m4nc4rc0 10.20.91.2 1.3.6.1.4.1.9.9.109.1.1.1.1.7
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.7.4000 = Gauge32: 9
C:\usr>
ADDITIONAL INFORMATION
C:\usr>
C:\usr>snmpwalk -v 2c -c m4nc4rc0 10.20.91.2 1.3.6.1.2.1.90
SNMPv2-SMI::mib-2.90.1.1.1.0 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.1.2.0 = Gauge32: 0
SNMPv2-SMI::mib-2.90.1.1.3.0 = Gauge32: 0
SNMPv2-SMI::mib-2.90.1.1.4.0 = Gauge32: 0
SNMPv2-SMI::mib-2.90.1.1.5.0 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = STRING: "9"
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = STRING: "11"
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = STRING: "8"
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = STRING: "13"
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = STRING: "13"
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = STRING: "11"
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = INTEGER: 2
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = INTEGER: 2
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = INTEGER: 2
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = INTEGER: 2
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = INTEGER: 2
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = INTEGER: 2
C:\usr>
C:\usr>snmpwalk -v 2c -c m4nc4rc0 10.20.91.2 1.3.6.1.2.1.47.1.1.1.1.2
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1 = STRING: "Cisco Systems, Inc. WS-C4507R+E 7 sl
ot switch "
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.3 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.6 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.7 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.8 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.9 = STRING: " WS-C4507R+E 7 slot switch backplane
SNMPv2-SMI::mib-2.47.1.1.1.1.2.10 = STRING: "Container of Fan Tray"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.11 = STRING: "FanTray"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.12 = STRING: "Container of Container of Power Sup
ply"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.13 = STRING: "Container of Power Supply"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.14 = STRING: "Power Supply ( AC 2800W )"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.15 = STRING: "Power Supply Fan Sensor"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.16 = STRING: "Container of Power Supply"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.19 = STRING: "Clock Module"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.20 = STRING: "Mux Buffers for Redundancy Logic"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.21 = STRING: "Mux Buffers for Redundancy Logic"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.22 = STRING: "Mux Buffers for Redundancy Logic"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.23 = STRING: "Mux Buffers for Redundancy Logic"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.24 = STRING: "Mux Buffers for Redundancy Logic"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1000 = STRING: "10GE (X2), 1000BaseX (SFP) with 6
10GE X2 ports"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1001 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1002 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1003 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1004 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1005 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1006 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2000 = STRING: "1000BaseX (SFP) with 24 SFP Ports
Jumbo Frame Support"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2001 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2002 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2003 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2004 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2005 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2006 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2007 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2008 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2009 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2010 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2011 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2012 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2013 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2014 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2015 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2016 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2017 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2018 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2019 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2020 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2021 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2022 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2023 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2024 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2047 = STRING: "1000BaseSX"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2048 = STRING: "1000BaseSX"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4000 = STRING: "Sup 7-E 10GE (SFP+), 1000BaseX (S
FP) with 4 SFP+ Ports"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4001 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4002 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4003 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4004 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5000 = STRING: "10/100/1000BaseT (RJ45)V with 48
10/100/1000 baseT voice power ports (Cisco/IEEE)"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5001 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5002 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5003 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5004 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5005 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5006 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5007 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5008 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5009 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5010 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5011 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5012 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5013 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5014 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5015 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5016 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5017 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5018 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5019 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5020 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5021 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5022 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5023 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5024 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5025 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5026 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5027 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5028 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5029 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5030 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5031 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5032 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5033 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5034 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5035 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5036 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5037 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5038 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5039 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5040 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5041 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5042 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5043 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5044 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5045 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5046 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5047 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5048 = STRING: "Gigabit Ethernet Port"
C:\usr>

CISCO CATALYST 4507R+E + Supervisor 8-E

Hi,
I need help and clarification regarding the software license of Sup 7-E and Sup 8-E. Based on the catalog it ships with IOS XE universal image? Here are my inquiries.
1. With IOS XE universal image, what is the software license installed in Sup 7-E and Sup 8-E? Is it LAN Base or IP Base?
2. Is there an option to purchase the Sup 7-E or Sup 8-E with an Enterprise Base license?
3. How many priority queue does it support?
Thank you,

Please find answer:
1- Cisco provides LAN Base software only when purchasing SUP7E or SUP7L-E bundle with a single Supervisor, in all other cases IP Base license is provided at no additional cost.
There will continue to be three packages: LAN Base, IP Base, and Enterprise Services. ( IP Base and Enterprise services to be purchases seperately)
2-
Q.    Which licenses are available for Supervisor Engine 7-E, 7L-E or a Cisco Catalyst 4500-X Series system?
A.     See Table 1 for package licenses. These will be delivered with new Supervisors or available as an upgrade through Cisco software activation. The Cisco Catalyst 4500-X Series only supports IP Base (default) and Enterprise Services (as an upgrade).
Table 1.       Package licenses
Package Name
Prerequisites
License Types
LAN Base
None
Permanent
IP Base
IP Base
Permanent, temporary
Enterprise Services
IP Base
Permanent, temporary
Q.    Where can I learn more about Cisco software activation?
A.     http://www.cisco.com/go/sa.
3- http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-4500-series-switches/white_paper_c11-539588.html
HtH
Regards
Inayath
*Plz dont forget to rate usefull posts.

Catalyst 4006 with Supervisor Engine II Multicast Support?

Similar Messages

Maybe you are looking for