Catalyst 4507R+E Clock Module

Hi,
I noticed that my 4507R+E chassis have the following module installed:
WS-X4K-CLOCK-E
I found in this EOL announcement that it's the clock module for 4507R-E chassis and is EoS since 2013:
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-4500-series-switches/eol_C51-715893.html
Why the same module is installed in the new chassis and there are no spare parts available ?
Thanks,
Aron

This catalyst 4507R-E whit this Supervisor Supervisor II+ WS-X4013+ suppourt thos module WS-X4648-RJ45V+E ?
No, your supervisor only supports classic linecards but the WS-4648-RJ45V+E is not a classic line card so it is not supported. Have a look at this link and refer to Table 1 which shows which supervisors you could use with this card -
http://www.cisco.com/en/US/prod/collateral/modules/ps2710/ps5494/product_data_sheet0900aecd802109ea.html
Jon

Similar Messages

Cisco Catalyst 4507R Module WS X4424GB RJ 45, Multi-speed Gigabit Ethernet Switching Module (24-port)

i am confused if this one
Cisco Catalyst 4507R Module WS X4424GB RJ 45, Multi-speed Gigabit Ethernet Switching Module (24-port)
would be compatible to its chasis if change by this one
WS-X4424-GBRJ45-RF
Catalyst 4000 24port 101001000 Module RJ45 REFURBISHED

Yes it you get the refurbished with the good one then it would get detected and works fine.
BTW- This module is EOL /EOS and below is the replacement part for the same:
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-4500-series-switches/eol_c51_574038.html
WS-X4424-GB-RJ45
Catalyst 4500 24-port 10/100/1000 Module (RJ45)
Replacement-PartWS-X4548-GB-RJ45
Catalyst 4500 Enhanced 48-Port 10/100/1000 Base-T (RJ-45)
HTH
Regards
Inayath
***** Plz rate all usefull posts.

Cisco Catalyst 4507R+E with WS-X4748 blade, ports not working

I have a Cisco Catalyst 4507R+E (with Sup7-E) and two blades; one WS-X4748-RJ45V+E and one WS-X4648-RJ45-E.
When I connect a device to a port on the WS-X4748-RJ45V+E blade the port will not come up, show interface shows the status as "notconnect". When I connect the same device to the WS-X4648-RJ45-E blade the interface comes up.
The WS-X4748-RJ45V+E blade seems to have initialised okay, it appears in the output of "show module" as OK.
I get exactly the same effect on a second, identically configured Catalyst 4507R+E.
The software version is IOS XE 3.1.0SG, which according to the release notes supports the WS-X4748-RJ45V+E blade. Has anybody else seen anything like this?

I have 2 Core switches, single SUP on each.
Line cards #1 and #2 randomly stop forwarding packets, only solution is to reload the switch ( hw-module reset does not work ). I have cat4500e-universalk9.SPA.03.05.00.E.152-1.E.bin and the sympton looks the same as the described one,
although the code is newer than 3.2.2SG.
Now we are downgrading to cat4500e-universalk9.SPA.03.04.02.SG.151-2.SG2.bin to check if that solves the issue,
otherwise we´ll try removing/re-inserting the modules, and if issue persists, most probably RMA the Core1.
We´ve sent a show tech to Cisco support while the issue was happening.
Current modules on the Core switches.
Mod Ports Card Type                              Model              Serial No.
---+-----+--------------------------------------+------------------+-----------
1    48 10/100/1000BaseT EEE (RJ45)            WS-X4748-RJ45-E    CAT1627L48B
2    48 10/100/1000BaseT EEE (RJ45)            WS-X4748-RJ45-E    CAT1629L0ZY
3     4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP)   WS-X45-SUP7-E      CAT1629L1PD
5    12 1000BaseX (SFP)                        WS-X4612-SFP-E     JAE163007EO
M MAC addresses                    Hw Fw           Sw               Status
--+--------------------------------+---+------------+----------------+---------
1 30f7.0d57.80c0 to 30f7.0d57.80ef 1.1                               Ok
2 30f7.0dac.fd40 to 30f7.0dac.fd6f 1.1                               Ok
3 30f7.0dca.6c00 to 30f7.0dca.6c03 2.1 15.0(1r)SG10 03.05.00.E       Ok
5 a493.4c44.13e8 to a493.4c44.13f3 1.1                               Ok
Mod Redundancy role     Operating mode      Redundancy status
----+-------------------+-------------------+----------------------------------
3   Active Supervisor   SSO                 Active

Erasing a config and vlan.dat file in Catalyst 4507R Switch

Hi,
I am unable to erase the configuration from Catalyst 4507R Switch.When i do "write erase" and reload the switch,the configuration still remains on the switch.
Switch1#write erase
Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]
[OK]
Erase of nvram: complete
mp024-dc-nr00#sh start
startup-config is not present
After this i did reload and configuration still didn't get removed.
I tried
erase /all nvram:
reload
This also didn't help.
I also tried:
erase /all non-default
reload
This also didn't help.
Can anyone suggest how to erase the config on Catalyst 4507R Switch.
Thanks,

Hi Saroj,
do you see the below symtoms:
Cat4500# write erase
Erasing the nvram filesystem will remove all files! Continue? [confirm]y[OK]
Erase of nvram: complete
Cat4500# reload
System configuration has been modified. Save? [yes/no]: n
!--- Do not save the configuration at this prompt. Otherwise, the switch
!--- reloads with the current running configuration and does not reset to default.
Proceed with reload? [confirm]y
2w0d: %SYS-5-RELOAD: Reload requested
To erase the vlan.dat file on the 6500/6000 switches, issue the erase const_nvram: command. On the 4500/4000 switches, issue the erase cat4000_flash: command. On the fixed configuration switches, issue the delete flash:vlan.dat command.
HTH
Regards
Inayath

Password recovery at catalyst 4507R-E

Hi. I have catalyst 4507R-E and 2 engines are located at this catalyst. the engines are active standby. when i begin to recover i write the recover config at main engine then i must be reset the catalyst after reboot active engine go to satndby and standby go to active. so i can not recover it.
how can i solve this?
must i first remove standby engine and then recover active engine
then put the standby and active engine configuration go to standby.
am i rigth? i am afraid the i lost the configuration because i have not backup configuration.
i used this PDF.
please write your comment.
thank you very much.

Hi teymur,
You never lost your configuration, what you need to do is...
1. Make a complete config synch between active and standby supervisor engine (I hope autosync is already enabled)
2. Write the config to NVRAM on standby supervisor engine.
3. Now when you put back the standby supervisor engine, reload the active supervisor engine whcih take the standby be active and active be standby.
Also I would like to infor the password recovery procedure for you...
Try the below procedure with only one supervisor in the chassis.
1) Connect the console cable to the Supervisor IV console port
2) Reset the 4507 by power cycling the unit.
3) Interrupt the boot sequence by hitting CTRL+C
4) Using the confreg command, I set it to skip the boot-up configuration.
5) I issue the reset command to reboot the 4507 again.
http://www.cisco.com/en/US/products/hw/switches/ps663/products_password_recovery09186a00800945f7.shtml
Please rate the helpful posts.
Regards,
Naidu.

Clock module on 9140

Hello,
My switch is MDS9140. Here is the 'show envir' result:
`show environment`
Clock:
Clock Model Hw Status
A Clock Module -- not present/------
B Clock Module -- not present/------
IS my switch ok? Does it should have a clock module? Can anybody tell me that?
And I met some problems on MDS interfaces. I follow the guidance to do some 'show hardware internal fc-mac ...' command. Can anybody tell me where I can find command reference of these commands?
Thanks a lot.
Regards,
Sha

HI Nisha..
You can ensure that a PAI module is only called when a
certain condition applies by using the following
statement:
FIELD <f> MODULE <mod> ON INPUT|REQUEST|*-INPUT.
The additions have the following effects:
ON INPUT
The ABAP module is called only if the field contains a
value other than its initial value. This initial value is
determined by the data type of the field: Space for
character fields, zero for numeric fields. Even if the
user enters the initial value of the screen as the
initial value, the module is not called. (ON REQUEST, on
the other hand, does trigger the call in this case.)
ON REQUEST
The module <mod> is only called if the user has entered
something in the field. This includes cases when the user
overwrites an existing value with the same value, or
explicitly enters the initial value.
In general, the ON REQUEST condition is triggered
through any form of "manual input". As well as user
input, the following additional methods of entering
values also call the module:
The element attribute PARAMETER-ID (SPA/GPA parameters).
The element attribute HOLD DATA
CALL TRANSACTION ... USING
Automatic settings of particular global fields
ON *-INPUT
The ABAP module is called if the user has entered a "*"
in the first character of the field, and the field has
the attribute *-entry in the Screen Painter. When the
input field is passed to the program, the * is removed. *
behaves like an initial field in the ON INPUT condition.
If it helps Reward with Points
Regards,
Rk

Catalyst 4507R plus E Switch Discovery Issue

Hi,
I am having issues doing automatic discovery for Cisco Catalyst 4507R plus E Switch IOS 12.2(54)SG, I am using IP ping sweep to discover devices on my network.
When i first setup LMS4.0 with few devices on the network, i discover the C4507 without a problem together with other devices i have on the network but for some reasons now its failing to discover C4507. I have large numbers of WS-C3560X and C4507 on the network, WS-C3560X always discovered just fine.
I tried to use SolarWinds network device monitor I installed on the server to check if there's any SNMP or connectivity issues. I can discover C4507 using Solarwinds without a problem, so im suspecting it could be LMS configuration issue.
Is there any special settings I need to tweak to make this working?

A newer version of IOS should generally be fine.
It's generally the SNMP sysObjectID that LSM keys into. As noted in the table you cited, it should be 1.3.6.1.4.1.9.1.1286 for the 4507R+E.

Catalyst: fglrx and kernel module

I just installed arch linux 2009-08 on my laptop, and I installed catalyst using yaourt. My system is updated.
Catalyst driver and dependencies are installed, fglrx added on modules on rc.conf but on startup when loading modules it says:
FATAL: error inserting fglrx /lib/moduls/2.6.30-arch/video/fglrx.ko: unknown symbol in module, or unknown parameter (see dmesg)
what should I do?
thx

do:
lsmod | grep fglrx
To double check if you got it installed right

XFCE4: Could not open "clock" module [solved]

This has been a problem for me for a while, and it's utterly annoying. I can't add a clock to my GUI. And when I finally mess around with it and get it to appear one way or another, it disappears the next time I start XFCE.
How can I get a clock on my panel?!
Last edited by synthead (2007-05-31 09:05:53)

/usr/bin is not the start directory when starting xfce4-panel, probably your home directory so if there is a clock folder/file there, loading the module fails. But if you can add the clock and after a restart it is gone (and the ~/.config/xfce4/panel/panel.xml file has no clock entry), you probably have some permission problem.
Last edited by xerverius (2007-05-31 08:49:18)

Catalyst 3850 Stack - 10G Modules

I have installed a (3) switch stack of Catalyst 3850 switches. I installed a 10G module in the 1st switch (the master) configured it and plugged it into the network and all works fine. Now I would like to add a second 10 Gigabit Ethernet connection to the stack in a channel group. When I install the 10G module into the standby switch (switch 3) I can do a "show inventory" and the 10G module is there. I can configure TenGigabitEthernet 3/1/3 and do a show run interface TenGigabitEthernet 3/1/3 all looks normal, but when I do a "show interface status" it is not listed and I cannot get the interface to come up. Is there anything I maybe missing when installing the 10G module or in my configurations?
Thanks!

Hello Martin,
As a reference, please look at this link, it may help you,
https://supportforums.cisco.com/docs/DOC-36084
Berta.
MARTIN HUERTER escribió:I have installed a (3) switch stack of Catalyst 3850 switches. I installed a 10G module in the 1st switch (the master) configured it and plugged it into the network and all works fine. Now I would like to add a second 10 Gigabit Ethernet connection to the stack in a channel group. When I install the 10G module into the standby switch (switch 3) I can do a "show inventory" and the 10G module is there. I can configure TenGigabitEthernet 3/1/3 and do a show run interface TenGigabitEthernet 3/1/3 all looks normal, but when I do a "show interface status" it is not listed and I cannot get the interface to come up. Is there anything I maybe missing when installing the 10G module or in my configurations?Thanks!

Catalyst 4507R-E

Hi
I am using catalyst 4507 R-E
I did the password recovery and then when I reloaded the below info appears in the rommom mode
please help
as how can solve this problem
I have reloaded several times but its the same
* Welcome to Rom Monitor for WS-X4515 System. *
* Copyright (c) 1999-2004 by Cisco Systems, Inc. *
* All rights reserved. *
Rom Monitor Program Version 12.2(20r)EW1
Supervisor: WS-X4515 Chassis: Unknown( 5 )
Hardware Revisions - Board: 2.14 CPLD: 32 Dagobah: 226
MAC Address : 00-15-c6-bd-d3-54
IP Address : 10.10.10.10
Netmask : 255.255.255.0
Gateway : Not set.
TftpServer : 10.10.10.11
Main Memory : 512 MBytes
***** The system will autoboot in 5 seconds *****
Type control-C to prevent autobooting.
******** The system will autoboot now ********
config-register = 0x2102
Autobooting using BOOT variable specified file.....
Could not find a valid file in BOOT environment variable.
BOOT variable can be set from IOS. To find currently set
Rom Monitor variables, please type 'set' command.
For help on choosing a boot method, type 'confreg' command.
rommon 1 >
rommon 1 >

Hi
I am using catalyst 4507 R-E
I did the password recovery and then when I reloaded the below info appears in the rommom mode
please help
as how can solve this problem
I have reloaded several times but its the same
* Welcome to Rom Monitor for WS-X4515 System. *
* Copyright (c) 1999-2004 by Cisco Systems, Inc. *
* All rights reserved. *
Rom Monitor Program Version 12.2(20r)EW1
Supervisor: WS-X4515 Chassis: Unknown( 5 )
Hardware Revisions - Board: 2.14 CPLD: 32 Dagobah: 226
MAC Address : 00-15-c6-bd-d3-54
IP Address : 10.10.10.10
Netmask : 255.255.255.0
Gateway : Not set.
TftpServer : 10.10.10.11
Main Memory : 512 MBytes
***** The system will autoboot in 5 seconds *****
Type control-C to prevent autobooting.
******** The system will autoboot now ********
config-register = 0x2102
Autobooting using BOOT variable specified file.....
Could not find a valid file in BOOT environment variable.
BOOT variable can be set from IOS. To find currently set
Rom Monitor variables, please type 'set' command.
For help on choosing a boot method, type 'confreg' command.
rommon 1 >
rommon 1 >

CISCO CATALYST 4507R+E + Supervisor 8-E

Hi,
I need help and clarification regarding the software license of Sup 7-E and Sup 8-E. Based on the catalog it ships with IOS XE universal image? Here are my inquiries.
1. With IOS XE universal image, what is the software license installed in Sup 7-E and Sup 8-E? Is it LAN Base or IP Base?
2. Is there an option to purchase the Sup 7-E or Sup 8-E with an Enterprise Base license?
3. How many priority queue does it support?
Thank you,

Please find answer:
1- Cisco provides LAN Base software only when purchasing SUP7E or SUP7L-E bundle with a single Supervisor, in all other cases IP Base license is provided at no additional cost.
There will continue to be three packages: LAN Base, IP Base, and Enterprise Services. ( IP Base and Enterprise services to be purchases seperately)
2-
Q.    Which licenses are available for Supervisor Engine 7-E, 7L-E or a Cisco Catalyst 4500-X Series system?
A.     See Table 1 for package licenses. These will be delivered with new Supervisors or available as an upgrade through Cisco software activation. The Cisco Catalyst 4500-X Series only supports IP Base (default) and Enterprise Services (as an upgrade).
Table 1.       Package licenses
Package Name
Prerequisites
License Types
LAN Base
None
Permanent
IP Base
IP Base
Permanent, temporary
Enterprise Services
IP Base
Permanent, temporary
Q.    Where can I learn more about Cisco software activation?
A.     http://www.cisco.com/go/sa.
3- http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-4500-series-switches/white_paper_c11-539588.html
HtH
Regards
Inayath
*Plz dont forget to rate usefull posts.

Catalyst 4500 Gigabit Ethernet Module, 6-Ports (GBIC)

hi everybody
I want to know if this module "WS-X4306-GB" is hot swappable?
could you pls tell me asap.
thanks

Yex, it is hot-swappable. most of the line card in Cat4000 are hot-swappable.
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/hw_doc/mod_inst/01overvw.htm#wp1026199
Please rate helpful posts.

Pb access-list Catalyst 4507r

Hi
I have 2 vlan : 192.168.38.0 and 192.168.31.0.
In the 38.0 network, I have an exchange server.
And in the 31.0 network, I have a clients(microsoft outlook).
The pb is when i configure the access-list, the client start a 135 port communication but it don't have an answer.
But if i open the all port, it's Ok.
Here, my access-list.
Could you confirm if it's ok
in advance, Thank you
access-list 131 remark sur interface vlan 31 Client NB
access-list 131 permit ip any 192.168.31.0 0.0.0.255
access-list 131 permit tcp any host 192.168.38.203 eq 135
access-list 131 permit icmp any 192.168.38.0 0.0.0.255
access-list 131 deny ip any any
access-list 138 remark sur interface vlan 38 Bureautique
access-list 138 permit ip any 192.168.38.0 0.0.0.255
access-list 138 permit icmp any 192.168.31.0 0.0.0.255
access-list 138 deny ip any any

Hi,
Thank you very much.
When i see with the ethereal soft, the client need to open a range port(>1024).
Please give me the access-list
In advance thanks!!

LMS 3.2 and Catalyst 4500 WS-X4648-RJ45-E module card

Hi all,
I have a rpoblem with a specific client with LMS 3.2. We are using LMS 3.2 on Windows 2008 and everything seem to be working OK. The issue is in the CiscoView with the 4500 switches. CiscoView can see the supervisors on all 4500 switches (6); but cannot see the switchcards when the switchcards are WS-X4648-RJ45-E. Find the sh inv output below:
CSR-D1#sh inventory
NAME: "Switch System", DESCR: "Cisco Systems, Inc. WS-C4507R-E 7 slot switch "
PID: WS-C4507R-E       , VID: V01, SN: FOX1152GKR1
NAME: "Clock Module", DESCR: "Clock Module"
PID: WS-X4K-CLOCK-E    , VID: V01, SN: JAE120354DD
NAME: "Linecard(slot 1)", DESCR: "10/100/1000BaseT (RJ45) with 48 10/100/1000 baseT "
PID: WS-X4648-RJ45-E   , VID: V01, SN: JAE14410NLT
NAME: "Linecard(slot 2)", DESCR: "6 Dual media SFP or 10/100/1000BaseT (RJ45)V voice power ports (Cisco/IEEE)"
PID: WS-X4506-GB-T     , VID: V05, SN: JAE120351NC
NAME: "Linecard(slot 3)", DESCR: "Supervisor 6-E 10GE (X2), 1000BaseX (SFP) with 2 10GE X2 ports"
PID: WS-X45-SUP6-E     , VID: V01, SN: JAE120576HG
NAME: "TenGigabitEthernet3/1", DESCR: "10Gbase-LRM"
PID: FTLX1341E2-C1     , VID: A , SN: FNS1352175M
NAME: "TwinGig Converter 3/2", DESCR: "TwinGig Converter Module"
PID: 800-27645-01      , VID: A0 , SN: CAT1147H2WK
NAME: "Linecard(slot 4)", DESCR: "Supervisor 6-E 10GE (X2), 1000BaseX (SFP) with 2 10GE X2 ports"
PID: WS-X45-SUP6-E     , VID: V07, SN: JAE14080NL2
NAME: "TwinGig Converter 4/2", DESCR: "TwinGig Converter Module"
PID: 800-27645-01      , VID: A0 , SN: CAT1147H2BV
NAME: "Linecard(slot 7)", DESCR: "10/100/1000BaseT (RJ45) with 48 10/100/1000 baseT "
PID: WS-X4648-RJ45-E   , VID: V01, SN: JAE14420A2F
I have updated the s/w to 12.2(53) SG1 with no luck.
Any ideas?

Hi Nicos,
I have exactly the same issue with LMS 3.2 CiscoView under Windows 2003 and catalyst switch 4506-E.
4506-E are in IOS 12.2(53)SG2.
I installed latest 4500IOS V 19.0 ciscoview device package without success.
Did you fix your problem ?

Catalyst 4507R+E Clock Module

Similar Messages

Maybe you are looking for