Catalyst 4507R-E
Hi
I am using catalyst 4507 R-E
I did the password recovery and then when I reloaded the below info appears in the rommom mode
please help
as how can solve this problem
I have reloaded several times but its the same
* Welcome to Rom Monitor for WS-X4515 System. *
* Copyright (c) 1999-2004 by Cisco Systems, Inc. *
* All rights reserved. *
Rom Monitor Program Version 12.2(20r)EW1
Supervisor: WS-X4515 Chassis: Unknown( 5 )
Hardware Revisions - Board: 2.14 CPLD: 32 Dagobah: 226
MAC Address : 00-15-c6-bd-d3-54
IP Address : 10.10.10.10
Netmask : 255.255.255.0
Gateway : Not set.
TftpServer : 10.10.10.11
Main Memory : 512 MBytes
***** The system will autoboot in 5 seconds *****
Type control-C to prevent autobooting.
******** The system will autoboot now ********
config-register = 0x2102
Autobooting using BOOT variable specified file.....
Could not find a valid file in BOOT environment variable.
BOOT variable can be set from IOS. To find currently set
Rom Monitor variables, please type 'set' command.
For help on choosing a boot method, type 'confreg' command.
rommon 1 >
rommon 1 >
Hi
I am using catalyst 4507 R-E
I did the password recovery and then when I reloaded the below info appears in the rommom mode
please help
as how can solve this problem
I have reloaded several times but its the same
* Welcome to Rom Monitor for WS-X4515 System. *
* Copyright (c) 1999-2004 by Cisco Systems, Inc. *
* All rights reserved. *
Rom Monitor Program Version 12.2(20r)EW1
Supervisor: WS-X4515 Chassis: Unknown( 5 )
Hardware Revisions - Board: 2.14 CPLD: 32 Dagobah: 226
MAC Address : 00-15-c6-bd-d3-54
IP Address : 10.10.10.10
Netmask : 255.255.255.0
Gateway : Not set.
TftpServer : 10.10.10.11
Main Memory : 512 MBytes
***** The system will autoboot in 5 seconds *****
Type control-C to prevent autobooting.
******** The system will autoboot now ********
config-register = 0x2102
Autobooting using BOOT variable specified file.....
Could not find a valid file in BOOT environment variable.
BOOT variable can be set from IOS. To find currently set
Rom Monitor variables, please type 'set' command.
For help on choosing a boot method, type 'confreg' command.
rommon 1 >
rommon 1 >
Similar Messages
-
Erasing a config and vlan.dat file in Catalyst 4507R Switch
Hi,
I am unable to erase the configuration from Catalyst 4507R Switch.When i do "write erase" and reload the switch,the configuration still remains on the switch.
Switch1#write erase
Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]
[OK]
Erase of nvram: complete
mp024-dc-nr00#sh start
startup-config is not present
After this i did reload and configuration still didn't get removed.
I tried
erase /all nvram:
reload
This also didn't help.
I also tried:
erase /all non-default
reload
This also didn't help.
Can anyone suggest how to erase the config on Catalyst 4507R Switch.
Thanks,Hi Saroj,
do you see the below symtoms:
Cat4500# write erase
Erasing the nvram filesystem will remove all files! Continue? [confirm]y[OK]
Erase of nvram: complete
Cat4500# reload
System configuration has been modified. Save? [yes/no]: n
!--- Do not save the configuration at this prompt. Otherwise, the switch
!--- reloads with the current running configuration and does not reset to default.
Proceed with reload? [confirm]y
2w0d: %SYS-5-RELOAD: Reload requested
To erase the vlan.dat file on the 6500/6000 switches, issue the erase const_nvram: command. On the 4500/4000 switches, issue the erase cat4000_flash: command. On the fixed configuration switches, issue the delete flash:vlan.dat command.
HTH
Regards
Inayath -
Password recovery at catalyst 4507R-E
Hi. I have catalyst 4507R-E and 2 engines are located at this catalyst. the engines are active standby. when i begin to recover i write the recover config at main engine then i must be reset the catalyst after reboot active engine go to satndby and standby go to active. so i can not recover it.
how can i solve this?
must i first remove standby engine and then recover active engine
then put the standby and active engine configuration go to standby.
am i rigth? i am afraid the i lost the configuration because i have not backup configuration.
i used this PDF.
please write your comment.
thank you very much.Hi teymur,
You never lost your configuration, what you need to do is...
1. Make a complete config synch between active and standby supervisor engine (I hope autosync is already enabled)
2. Write the config to NVRAM on standby supervisor engine.
3. Now when you put back the standby supervisor engine, reload the active supervisor engine whcih take the standby be active and active be standby.
Also I would like to infor the password recovery procedure for you...
Try the below procedure with only one supervisor in the chassis.
1) Connect the console cable to the Supervisor IV console port
2) Reset the 4507 by power cycling the unit.
3) Interrupt the boot sequence by hitting CTRL+C
4) Using the confreg command, I set it to skip the boot-up configuration.
5) I issue the reset command to reboot the 4507 again.
http://www.cisco.com/en/US/products/hw/switches/ps663/products_password_recovery09186a00800945f7.shtml
Please rate the helpful posts.
Regards,
Naidu. -
Catalyst 4507R plus E Switch Discovery Issue
Hi,
I am having issues doing automatic discovery for Cisco Catalyst 4507R plus E Switch IOS 12.2(54)SG, I am using IP ping sweep to discover devices on my network.
When i first setup LMS4.0 with few devices on the network, i discover the C4507 without a problem together with other devices i have on the network but for some reasons now its failing to discover C4507. I have large numbers of WS-C3560X and C4507 on the network, WS-C3560X always discovered just fine.
I tried to use SolarWinds network device monitor I installed on the server to check if there's any SNMP or connectivity issues. I can discover C4507 using Solarwinds without a problem, so im suspecting it could be LMS configuration issue.
Is there any special settings I need to tweak to make this working?A newer version of IOS should generally be fine.
It's generally the SNMP sysObjectID that LSM keys into. As noted in the table you cited, it should be 1.3.6.1.4.1.9.1.1286 for the 4507R+E. -
Catalyst 4507R+E Clock Module
Hi,
I noticed that my 4507R+E chassis have the following module installed:
WS-X4K-CLOCK-E
I found in this EOL announcement that it's the clock module for 4507R-E chassis and is EoS since 2013:
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-4500-series-switches/eol_C51-715893.html
Why the same module is installed in the new chassis and there are no spare parts available ?
Thanks,
AronThis catalyst 4507R-E whit this Supervisor Supervisor II+ WS-X4013+ suppourt thos module WS-X4648-RJ45V+E ?
No, your supervisor only supports classic linecards but the WS-4648-RJ45V+E is not a classic line card so it is not supported. Have a look at this link and refer to Table 1 which shows which supervisors you could use with this card -
http://www.cisco.com/en/US/prod/collateral/modules/ps2710/ps5494/product_data_sheet0900aecd802109ea.html
Jon -
Cisco Catalyst 4507R+E with WS-X4748 blade, ports not working
I have a Cisco Catalyst 4507R+E (with Sup7-E) and two blades; one WS-X4748-RJ45V+E and one WS-X4648-RJ45-E.
When I connect a device to a port on the WS-X4748-RJ45V+E blade the port will not come up, show interface shows the status as "notconnect". When I connect the same device to the WS-X4648-RJ45-E blade the interface comes up.
The WS-X4748-RJ45V+E blade seems to have initialised okay, it appears in the output of "show module" as OK.
I get exactly the same effect on a second, identically configured Catalyst 4507R+E.
The software version is IOS XE 3.1.0SG, which according to the release notes supports the WS-X4748-RJ45V+E blade. Has anybody else seen anything like this?I have 2 Core switches, single SUP on each.
Line cards #1 and #2 randomly stop forwarding packets, only solution is to reload the switch ( hw-module reset does not work ). I have cat4500e-universalk9.SPA.03.05.00.E.152-1.E.bin and the sympton looks the same as the described one,
although the code is newer than 3.2.2SG.
Now we are downgrading to cat4500e-universalk9.SPA.03.04.02.SG.151-2.SG2.bin to check if that solves the issue,
otherwise we´ll try removing/re-inserting the modules, and if issue persists, most probably RMA the Core1.
We´ve sent a show tech to Cisco support while the issue was happening.
Current modules on the Core switches.
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 48 10/100/1000BaseT EEE (RJ45) WS-X4748-RJ45-E CAT1627L48B
2 48 10/100/1000BaseT EEE (RJ45) WS-X4748-RJ45-E CAT1629L0ZY
3 4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7-E CAT1629L1PD
5 12 1000BaseX (SFP) WS-X4612-SFP-E JAE163007EO
M MAC addresses Hw Fw Sw Status
--+--------------------------------+---+------------+----------------+---------
1 30f7.0d57.80c0 to 30f7.0d57.80ef 1.1 Ok
2 30f7.0dac.fd40 to 30f7.0dac.fd6f 1.1 Ok
3 30f7.0dca.6c00 to 30f7.0dca.6c03 2.1 15.0(1r)SG10 03.05.00.E Ok
5 a493.4c44.13e8 to a493.4c44.13f3 1.1 Ok
Mod Redundancy role Operating mode Redundancy status
----+-------------------+-------------------+----------------------------------
3 Active Supervisor SSO Active -
i am confused if this one
Cisco Catalyst 4507R Module WS X4424GB RJ 45, Multi-speed Gigabit Ethernet Switching Module (24-port)
would be compatible to its chasis if change by this one
WS-X4424-GBRJ45-RF
Catalyst 4000 24port 101001000 Module RJ45 REFURBISHEDYes it you get the refurbished with the good one then it would get detected and works fine.
BTW- This module is EOL /EOS and below is the replacement part for the same:
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-4500-series-switches/eol_c51_574038.html
WS-X4424-GB-RJ45
Catalyst 4500 24-port 10/100/1000 Module (RJ45)
Replacement-PartWS-X4548-GB-RJ45
Catalyst 4500 Enhanced 48-Port 10/100/1000 Base-T (RJ-45)
HTH
Regards
Inayath
***** Plz rate all usefull posts. -
CISCO CATALYST 4507R+E + Supervisor 8-E
Hi,
I need help and clarification regarding the software license of Sup 7-E and Sup 8-E. Based on the catalog it ships with IOS XE universal image? Here are my inquiries.
1. With IOS XE universal image, what is the software license installed in Sup 7-E and Sup 8-E? Is it LAN Base or IP Base?
2. Is there an option to purchase the Sup 7-E or Sup 8-E with an Enterprise Base license?
3. How many priority queue does it support?
Thank you,Please find answer:
1- Cisco provides LAN Base software only when purchasing SUP7E or SUP7L-E bundle with a single Supervisor, in all other cases IP Base license is provided at no additional cost.
There will continue to be three packages: LAN Base, IP Base, and Enterprise Services. ( IP Base and Enterprise services to be purchases seperately)
2-
Q. Which licenses are available for Supervisor Engine 7-E, 7L-E or a Cisco Catalyst 4500-X Series system?
A. See Table 1 for package licenses. These will be delivered with new Supervisors or available as an upgrade through Cisco software activation. The Cisco Catalyst 4500-X Series only supports IP Base (default) and Enterprise Services (as an upgrade).
Table 1. Package licenses
Package Name
Prerequisites
License Types
LAN Base
None
Permanent
IP Base
IP Base
Permanent, temporary
Enterprise Services
IP Base
Permanent, temporary
Q. Where can I learn more about Cisco software activation?
A. http://www.cisco.com/go/sa.
3- http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-4500-series-switches/white_paper_c11-539588.html
HtH
Regards
Inayath
*Plz dont forget to rate usefull posts. -
Hi
I have 2 vlan : 192.168.38.0 and 192.168.31.0.
In the 38.0 network, I have an exchange server.
And in the 31.0 network, I have a clients(microsoft outlook).
The pb is when i configure the access-list, the client start a 135 port communication but it don't have an answer.
But if i open the all port, it's Ok.
Here, my access-list.
Could you confirm if it's ok
in advance, Thank you
access-list 131 remark sur interface vlan 31 Client NB
access-list 131 permit ip any 192.168.31.0 0.0.0.255
access-list 131 permit tcp any host 192.168.38.203 eq 135
access-list 131 permit icmp any 192.168.38.0 0.0.0.255
access-list 131 deny ip any any
access-list 138 remark sur interface vlan 38 Bureautique
access-list 138 permit ip any 192.168.38.0 0.0.0.255
access-list 138 permit icmp any 192.168.31.0 0.0.0.255
access-list 138 deny ip any anyHi,
Thank you very much.
When i see with the ethereal soft, the client need to open a range port(>1024).
Please give me the access-list
In advance thanks!! -
Can't make redirect-list on 4507R-E
I need to deploy WAAS between a branch and HQ.
The HQ side is a catalyst switch 6509-E (VSS) and branch side is a catalyst 4507R-E.
The 6509-E supports "Redirect Filter" (an access-list) filtering just the traffic you want. The following is my access-list on HQ side :
ip wccp 61 redirect-list WCCPLIST group-list 3
ip wccp 62 redirect-list WCCPLIST group-list 3
access-list 3 permit 10.X.X.X <--------- WAE IP address
ip access-list extended WCCPLIST
remark ** ACL used for WCCP redirect-list **
remark Deny VoIP Control Traffic
deny tcp any any eq 1300
deny tcp any any eq 2428
deny tcp any any eq 2000
deny tcp any any eq 2001
deny tcp any any eq 2002
deny tcp any any eq 2443
deny tcp any any eq 1718
deny tcp any any eq 1719
deny tcp any any eq 1720
deny tcp any any eq 5060
deny tcp any any range 11000 11999
remark Deny MGT Traffic
deny tcp any any eq telnet
deny tcp any eq telnet any
deny tcp any any eq 22
deny tcp any any eq 161
deny tcp any any eq 162
deny tcp any any eq 123
deny tcp any any eq 8443
remark Deny Routing
deny tcp any any eq bgp
remark Deny Authentication Traffic
deny tcp any any eq tacacs
remark Accelerate Traffic between Branch and HQ
permit tcp 10.Br.Br.0 0.0.0.255 10.HQ.HQ.0 0.0.0.255
permit tcp 10.HQ.HQ.0 0.0.0.255 10.Br.Br.0 0.0.0.255
Whereas on the Branch side, the platform 4507R-E doesn't support ACL with WCCP, so it means the WCCP will intercept all the TCP traffic.
What would be the impact and how do i deal with this situation.
Or is the WAEintellgent enough to pass through the unwanted traffic ?
Or do i need to make individual policy for pass-through for each of the unwanted traffic ?
Regards,
JilaniHi Jilani,
Can't see from your mail what kind of supervisor you are using in your 45xx switch.
But please be aware that if your're using af SUP-7-E or a SUP-7-L-E WCCP is NOT supported for the time being.
WCCP is supported in Hardware but we're waiting for a software release, which supports this.
This is according to the release notes :
SUP-7-L-E : http://www.cisco.com/en/US/partner/docs/switches/lan/catalyst4500/release/note/OL_25346.html
SUP-7-E : http://www.cisco.com/en/US/partner/docs/switches/lan/catalyst4500/release/note/OL_24726.html
Strange thing is that you can actually "configure" some WCCP stuff, but the config will never hit the running-config.
And you cannot enable WCCP.
Feature navigator states that WCCP is available in IOS XE 3.2.0XO (for SUP-7-L-E) but release notes tend to be more trustworthy that feature navigator.
Best Regards
Finn Poulsen -
Unable to connect a Netapp San to a Cisco Catalyst in 10Gb
I have a Cisco Catalyst 4507R with a WS-X4606-X2-E and X2-10GB-SR to be connected to a Netapp SAN and it does not work.
With show interface transceiver detail it seems that the power sent by netapp is good but the link stay in dwon down state
Any help?down/down is related to layer 1 issue. Make sure the SFP is correct on both ends (and same type: LR vs SR) and also make sure you are using the right fiber. You can loop back on the same catalyst both sfps with the cable to see if the link comes up.
-
I have a Catalyst 4507R as a core switch.
The Data center has more than 40 servers, but I need two of these 40 servers communicate only among themselves and with the remaining company networks.
Can you help me?
RegardsDisclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
So the two special servers need to NOT communicate with just the other 38 servers? If so, place in different subnet/VLAN from other servers and use ACL(s).
Or, if your equipment supports, place the two special servers within a PVLAN community separate from your other servers. -
WCCP version 2 on Catalyst 4507 w/SupII+
Hello,
I am try to do a lab with WAAS but I have a switch Catalyst 4507 with Supervisor II+.
When I am doing the configuration, I can´t use the "ip wccp redirect exclude in" on the vlan where reside the WAAS.
The show version is:
MBO-SW-01#
MBO-SW-01#
MBO-SW-01#sh ver
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(53)SG1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Fri 30-Oct-09 14:39 by prod_rel_team
Image text-base: 0x10000000, data-base: 0x11D20300
ROM: 12.2(31r)SGA1
Dagobah Revision 226, Swamp Revision 34
MBO-SW-01 uptime is 4 weeks, 6 days, 22 hours, 14 minutes
Uptime for this control processor is 4 weeks, 6 days, 22 hours, 15 minutes
System returned to ROM by power-on
System restarted at 16:57:06 CCS Mon May 10 2010
System image file is "bootflash:/cat4500-ipbasek9-mz.122-53.SG1.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html you require further assistance please contact us by sending email to
[email protected]. WS-C4507R (MPC8245) processor (revision 10) with 262144K bytes of memory.
Processor board ID FOX1151GHMY
MPC8245 CPU at 266Mhz, Supervisor II+
Last reset from PowerUp
7 Virtual Ethernet interfaces
48 FastEthernet interfaces
26 Gigabit Ethernet interfaces
511K bytes of non-volatile configuration memory.
If
cisco
Configuration register is 0x102
MBO-SW-01#
MBO-SW-01#
MBO-SW-01#
MBO-SW-01#sh mod
Chassis Type : WS-C4507R
Power consumed by backplane : 40 Watts
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 2 Supervisor II+ 1000BaseX (GBIC) WS-X4013+ JAE12035A3E
3 24 10/100BaseTX (RJ45)V, Cisco/IEEE WS-X4224-RJ45V JAE1038BPFF
4 24 10/100BaseTX (RJ45)V, Cisco/IEEE WS-X4224-RJ45V JAE1041D5JM
5 24 10/100/1000BaseT (RJ45)V, Cisco/IEEE WS-X4524-GB-RJ45V JAE11517SDQ
M MAC addresses Hw Fw Sw Status
--+--------------------------------+---+------------+----------------+---------
1 001f.9e15.32c0 to 001f.9e15.32c1 4.5 12.2(31r)SGA 12.2(53)SG1 Ok
3 0016.4617.b1b8 to 0016.4617.b1cf 2.3 Ok
4 0018.18b5.85e8 to 0018.18b5.85ff 2.3 Ok
5 0017.0ec4.6350 to 0017.0ec4.6367 2.3 Ok
Mod Redundancy role Operating mode Redundancy status
----+-------------------+-------------------+----------------------------------
1 Active Supervisor SSO Active
MBO-SW-01#
MBO-SW-01#sh ip wccp
Global WCCP information:
Router information:
Router Identifier: 192.168.166.1
Protocol Version: 2.0
Service Identifier: 61
Number of Service Group Clients: 0
Number of Service Group Routers: 0
Total Packets s/w Redirected: 0
Process: 0
CEF: 0
Redirect access-list: -none-
Total Packets Denied Redirect: 0
Total Packets Unassigned: 0
Group access-list: -none-
Total Messages Denied to Group: 0
Total Authentication failures: 0
Total Bypassed Packets Received: 0
Service Identifier: 62
Number of Service Group Clients: 0
Number of Service Group Routers: 0
Total Packets s/w Redirected: 0
Process: 0
CEF: 0
Redirect access-list: -none-
Total Packets Denied Redirect: 0
Total Packets Unassigned: 0
Group access-list: -none-
Total Messages Denied to Group: 0
Total Authentication failures: 0
Total Bypassed Packets Received: 0
MBO-SW-01#
MBO-SW-01#
MBO-SW-01#
MBO-SW-01#sh ip wccp in
MBO-SW-01#sh ip wccp interfaces
WCCP interface configuration:
FastEthernet3/5
Output services: 0
Input services: 1
Mcast services: 0
Exclude In: FALSE
MBO-SW-01#
Who can I do, to get this work????
Thank a lotHi Zach,
Thanks for your answer, but I don´t have clearly the scenario of your answer.
I´m attaching the Logical Topology; and the configuration is this:
Configration of the Edge Site:
MBO-RT-03#
MBO-RT-03#sh run
Building configuration...
Current configuration : 10757 bytes
version 12.4
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime localtime
service timestamps log datetime localtime
service password-encryption
service sequence-numbers
hostname MBO-RT-03
boot-start-marker
boot-end-marker
ip wccp 61
ip wccp 62
ip cef
interface FastEthernet0/0
description TRONCAL LAN
no ip address
duplex auto
speed auto
interface FastEthernet0/0.202
description *** Vlan for Connection with WAE / Edge ***
encapsulation dot1Q 202
ip address 10.201.201.1 255.255.255.248
ip wccp redirect exclude in
interface FastEthernet0/0.210
description *** Vlan for Users ***
encapsulation dot1Q 210
ip address 192.168.166.129 255.255.255.128
ip wccp 61 redirect in
interface FastEthernet0/1
description *** WAN LINK - EMULATION ***
bandwidth 128
ip address 10.100.100.2 255.255.255.252
ip wccp 62 redirect in
ip nbar protocol-discovery
ip flow ingress
load-interval 30
duplex auto
speed auto
traffic-shape rate 128000 128000 128000 1000
router eigrp 1600
passive-interface default
no passive-interface FastEthernet0/1
network 10.100.100.2 0.0.0.0
network 10.201.201.1 0.0.0.0
network 192.168.166.128 0.0.0.127
no auto-summary
control-plane
line con 0
privilege level 15
password 7 121A150402181B00787B7578
login authentication userauthen
line aux 0
line vty 0 4
session-timeout 5
privilege level 15
password 7 121A150402181B00787B7578
login authentication userauthen
scheduler allocate 20000 1000
end
MBO-RT-03#
MBO-RT-03#
MBO-RT-03#
MBO-RT-03#sh ip wccp
Global WCCP information:
Router information:
Router Identifier: 192.168.166.129
Protocol Version: 2.0
Service Identifier: 61
Number of Service Group Clients: 1
Number of Service Group Routers: 1
Total Packets s/w Redirected: 39212
Process: 0
CEF: 39212
Service mode: Open
Service Access-list: -none-
Total Packets Dropped Closed: 0
Redirect Access-list: -none-
Total Packets Denied Redirect: 0
Total Packets Unassigned: 0
Group Access-list: -none-
Total Messages Denied to Group: 0
Total Authentication failures: 0
Total Bypassed Packets Received: 0
Service Identifier: 62
Number of Service Group Clients: 1
Number of Service Group Routers: 1
Total Packets s/w Redirected: 38171
Process: 0
CEF: 38171
Service mode: Open
Service Access-list: -none-
Total Packets Dropped Closed: 0
Redirect Access-list: -none-
Total Packets Denied Redirect: 0
Total Packets Unassigned: 0
Group Access-list: -none-
Total Messages Denied to Group: 0
Total Authentication failures: 0
Total Bypassed Packets Received: 0
MBO-RT-03#
MBO-RT-03#
MBO-RT-03#
MBO-RT-03#sh ip wccp inter
WCCP interface configuration:
FastEthernet0/1
Output services: 0
Input services: 1
Mcast services: 0
Exclude In: FALSE
FastEthernet0/0.210
Output services: 0
Input services: 1
Mcast services: 0
Exclude In: FALSE
FastEthernet0/0.202
Output services: 0
Input services: 0
Mcast services: 0
Exclude In: TRUE
MBO-RT-03#
MBO-RT-03#
MBO-RT-03#sh ver
Cisco IOS Software, 2801 Software (C2801-ADVENTERPRISEK9-M), Version 12.4(24)T2, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Mon 19-Oct-09 18:21 by prod_rel_team
ROM: System Bootstrap, Version 12.3(8r)T8, RELEASE SOFTWARE (fc1)
MBO-RT-03 uptime is 4 hours, 55 minutes
System returned to ROM by reload at 11:39:53 CCS Wed Jun 16 2010
System image file is "flash:c2801-adventerprisek9-mz.124-24.T2.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html you require further assistance please contact us by sending email to
[email protected]. 2801 (revision 5.0) with 240640K/21504K bytes of memory.
Processor board ID FTX0926W2NP
2 FastEthernet interfaces
1 Serial(sync/async) interface
1 Virtual Private Network (VPN) Module
2 Voice FXO interfaces
3 DSPs, 40 Voice resources
DRAM configuration is 64 bits wide with parity disabled.
191K bytes of NVRAM.
62720K bytes of ATA CompactFlash (Read/Write)
If
Cisco
Configuration register is 0x2102
MBO-RT-03#
And the Core Site has a 4507R with this configuration:
MBO-SW-01#sh run
Building configuration...
Current configuration : 33778 bytes
! Last configuration change at 16:54:12 CCS Wed Jun 16 2010 by dsalazar
! NVRAM config last updated at 16:05:21 CCS Wed Jun 16 2010 by dsalazar
version 12.2
service nagle
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime localtime
service timestamps log datetime localtime
service password-encryption
service compress-config
service udp-small-servers
service tcp-small-servers
service sequence-numbers
hostname MBO-SW-01
boot-start-marker
boot system flash bootflash:/cat4500-ipbasek9-mz.122-53.SG1.bin
boot-end-marker
logging buffered 1024000
logging console critical
enable secret 5 $1$vzCG$bkRWJO0nJuUvYq5mmU8G00
username cps privilege 15 password 7 011016174B18110B731C1F59
username CNAC_User privilege 0 password 7 096F602829040401595C557A
aaa new-model
aaa authentication login default local-case group radius enable
aaa authentication dot1x default group radius
aaa authorization network default group radius
qos
qos aggregate-policer Prueba 128000 bps 1000 byte conform-action transmit exceed-action drop
ip subnet-zero
ip wccp 61
ip wccp 62
policy-map QoS_Prueba
class class-default
police aggregate Prueba
interface FastEthernet3/5
description *** WAN LINK - Emulation ***
no switchport
bandwidth 128
ip address 10.100.100.1 255.255.255.252
ip wccp 62 redirect in
load-interval 30
service-policy output QoS_Prueba
interface Vlan2
description *** Vlan of Server ***
ip address 192.168.162.1 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
ip wccp 61 redirect in
interface Vlan910
description *** Vlan for WAE / Core and Mgmt ***
ip address 10.200.200.1 255.255.255.248
router eigrp 1600
passive-interface default
no passive-interface Vlan1
no passive-interface Vlan710
no passive-interface FastEthernet3/5
no auto-summary
eigrp stub connected summary
eigrp event-logging
network 10.0.2.1 0.0.0.0
network 10.100.100.1 0.0.0.0
network 172.16.0.1 0.0.0.0
MBO-SW-01#
MBO-SW-01#sh ip wccp
Global WCCP information:
Router information:
Router Identifier: 192.168.166.1
Protocol Version: 2.0
Service Identifier: 61
Number of Service Group Clients: 0
Number of Service Group Routers: 0
Total Packets s/w Redirected: 0
Process: 0
CEF: 0
Redirect access-list: -none-
Total Packets Denied Redirect: 0
Total Packets Unassigned: 0
Group access-list: -none-
Total Messages Denied to Group: 0
Total Authentication failures: 0
Total Bypassed Packets Received: 0
Service Identifier: 62
Number of Service Group Clients: 0
Number of Service Group Routers: 0
Total Packets s/w Redirected: 0
Process: 0
CEF: 0
Redirect access-list: -none-
Total Packets Denied Redirect: 0
Total Packets Unassigned: 0
Group access-list: -none-
Total Messages Denied to Group: 0
Total Authentication failures: 0
Total Bypassed Packets Received: 0
MBO-SW-01#
MBO-SW-01#sh ip wccp in
MBO-SW-01#sh ip wccp interfaces
WCCP interface configuration:
FastEthernet3/5
Output services: 0
Input services: 1
Mcast services: 0
Exclude In: FALSE
Vlan2
Output services: 0
Input services: 1
Mcast services: 0
Exclude In: FALSE
MBO-SW-01#
As you can see on the Catalyst 4507R the following stats are 0
Number of Service Group Clients: 0
Number of Service Group Routers: 0
for the services 61 and 62.
In the Router that start reflect a diferent value.
I can appreciate a technical information about how can I configure WCCP for the comunication between the Catalyst 4507 with Sup II+ with the WAE 474.
I probed with other router instead the catalyst 4507 and the configuration and communication were succesfully; that was for verify posible error of configuration on WAEs; but the final objetive is to use the catalyst 4507R.
Thank for your assistance. -
Exec-timeout doesn't seem to work
I've been having a devil of a time getting exec-timeout to clear idle vty/ssh sessions. This investigation started when we were rolling out new Catalyst 4507R+E switches with Sup7L-E's under IOS XE 03.04.02.SG (what they shipped from the factory with.) Idle SSH sessions on the vty lines were not being cleared, despite the config being:
line vty 0 4
access-class VTY_ACL in
exec-timeout 30 0
logging synchronous
length 0
transport input ssh
So I opened a TAC case, and eventually they referred to bug CSCug31122. This wasn't terribly satisfying, as we are not talking about new or revolutionary functionality, and a general distribution release on a mature platform. Clearing an idle session does not require the most sophisticated programmer at Cisco. But this led me to do more tests, and I have yet to find a hardware/IOS combination where this works correctly. So far I have failures for:
4507R+E/Sup7L-E/IOS XE 03.04.02.SG, both vty and console lines
3560/12.2(40)SE, vty lines with ssh
3750/12.2(44)SE6, vty lines with both telnet and ssh
3845/12.4(24)T6
This seems more than coincidence. Is there something I am missing, or is this an unusually complicated programming issue?Hi,
Did you reload the SALTCONFIG file from the updated SALT deployment file with the wsloadcf command? If not, you will still be using the old value until you update the SALTCONFIG file.
Regards,
Todd Little
Oracle Tuxedo Chief Architect -
Greetings forum. So I am working on a project that could potentially make use of PVLANs to isolate some hosting servers we are possibly going to bring online in the coming weeks. We currently have Catalyst 4507R switches as the core at our DC running IOS version 15.0(2)SG7. We are using SVIs for Inter-vlan routing on the 4507Rs. We are running VTP version 2 currently. I am trying to lock down some answers with regards to running PVLANs in my environment. Any help here is much appreciated.
I have read that to run PVLANs, you need to put your switches in transparent mode before enabling PVLANs. The thing I am not sure on is why. Do they say this because only VTP version 3 supports the synchronization of PVLANs in the VTP domain, and without version 3 your PVLANS will not be propagated, or is there an another reason to put your switches in transparent other than this. I understand that without v3 I would have to manually configure the PVLANS on my switches that would needs them. Just trying to understand if thats the reason they say to put VTP in transparent mode before implementing PVLANS or if there is something else to it I am missing. Can I run PVLANs using VTPv2 and manually configure the PVLANs on the switches that need them?
Secondly, in order to switch to using VTPv3 from VTPv2, are there any gotchas I need to be aware of. I have two VTP servers in my VTP domain. I understand VTPv3 works differently with regards to VTP updates. When I change to version 3, will the current VLAN Database be overwritten causing me to loose my current VLANs, or will the current VLANs stay as is while I go about switching all my switches to VTPv3. Would like to avoid wiping out my network if possible.
Third, I have a VMWare ESX setup. These new hosts will be VM servers. We do not have a license to support the Distributed VSwitch which allows PVLAN support for ESX VMs. These VMs are running on a Dell M1000e chassis with Cisco WS-CBS3130G-S switches in it. They have limited support for PVLANs. We have VLAN trunk uplinked to our core switches from these blade switches, and then trunk to the VMWare standard switch so we can control VLAN placement of the VLAN hosts. Looks like this:
4507R---------------->WS-CBS3130G-S----------->VMWareStandardSwitch--------->VMWare Guests
Trunk Trunk Access
I believe there is some way to set up using PVLANs using a setup like this. I think using an isolated PVLAN trunk port. The Blade switch does not seem to support that feature (running 12.2(40)EX1). This is said to be the desired practice when you have upstream switches which do not support PVLANs. Since my VMWare switch does not support them, but the switch linking the core to the vswitch does somewhat I am trying to understand the issues that would be seen there.
Again lots if questions. Any help would be much appreciated.Hi Hoan, we have a new manual that may be of help to you. I have attached it here. It is the newScale Service Library Quick Reference Design Guide. The guide provides an overview of the decisions newScale made when organizing our available service libraries, when pairing images with categories and services, as well as other tips and best practices—all focused on ease of use and navigation for the end user.
The link to the guide on ou
Maybe you are looking for
-
IPhone 3G - Apps no longer working
Hey! I have had my iPhone 3G (8GB) for about a year now after inheriting it from a family member. It was working great at the start; I could virtually get any app I wanted without it asking to update or anything (like it does now...) and the apps wer
-
I bought a splitter, works great with all devices except you view, phoned humax they directed me to bt I rang technical support they could not help, they sent an engineer who said that because the box links directly to the tv there is nothing bt will
-
Registering a Japanese iPhone as an American
I'm an American military spouse currently stationed in Japan. I purchased an iPhone a little over a month ago, with a Japanese carrier, and obviously have a Japanese (11 digit) phone number. I already have an Apple ID, which is associated with my (pr
-
How to intigrate the web services?
Hi Experts. I created internt services in SE80 and activated using SICF,I'm able to test individaul service working fine, I wanted to call one service from others and estblish a flow, How we can do this ? Thanks Naveen
-
Can we execute more than one SQL in Stored Procedure?
Please help me with this. I am connecting to SQL SERVER Thanks Venu