Catalyst 4507R plus E Switch Discovery Issue

Hi,
I am having issues doing automatic discovery for Cisco Catalyst 4507R plus E Switch IOS 12.2(54)SG, I am using IP ping sweep to discover devices on my network.
When i first setup LMS4.0 with few devices on the network, i discover the C4507 without a problem together with other devices i have on the network but for some reasons now its failing to discover C4507. I have large numbers of WS-C3560X and C4507 on the network, WS-C3560X always discovered just fine.
I tried to use SolarWinds network device monitor I installed on the server to check if there's any SNMP or connectivity issues. I can discover C4507 using Solarwinds without a problem, so im suspecting it could be LMS configuration issue.
Is there any special settings I need to tweak to make this working?

A newer version of IOS should generally be fine.
It's generally the SNMP sysObjectID that LSM keys into. As noted in the table you cited, it should be 1.3.6.1.4.1.9.1.1286 for the 4507R+E.

Similar Messages

  • Erasing a config and vlan.dat file in Catalyst 4507R Switch

    Hi,
    I am unable to erase the configuration from Catalyst 4507R Switch.When i do "write erase" and reload the switch,the configuration still remains on the switch.
    Switch1#write erase
    Erasing the nvram filesystem will remove all configuration files! Continue? [confirm]
    [OK]
    Erase of nvram: complete
    mp024-dc-nr00#sh start
    startup-config is not present
    After this i did reload and configuration still didn't get removed.
    I  tried
    erase /all nvram:
    reload
    This also didn't help.
    I also tried:
    erase /all non-default
    reload
    This also didn't help.
    Can anyone suggest how to erase the config on Catalyst 4507R Switch.
    Thanks,

    Hi Saroj,
    do you see the below symtoms:
    Cat4500# write erase
    Erasing the nvram filesystem will remove all files! Continue? [confirm]y[OK]
    Erase of nvram: complete
    Cat4500# reload
    System configuration has been modified. Save? [yes/no]: n   
    !--- Do not save the configuration at this prompt. Otherwise, the switch
    !--- reloads with the current running configuration and does not reset to default.
    Proceed with reload? [confirm]y                             
    2w0d: %SYS-5-RELOAD: Reload requested
    To erase the vlan.dat file on the 6500/6000 switches, issue the erase const_nvram: command. On the 4500/4000 switches, issue the erase cat4000_flash: command. On the fixed configuration switches, issue the delete flash:vlan.dat command.
    HTH
    Regards
    Inayath

  • Cisco Catalyst 4507R Module WS X4424GB RJ 45, Multi-speed Gigabit Ethernet Switching Module (24-port)

    i am confused if this one
    Cisco Catalyst 4507R Module WS X4424GB RJ 45, Multi-speed Gigabit Ethernet Switching Module (24-port)
    would be compatible to its chasis if change by this one
    WS-X4424-GBRJ45-RF
    Catalyst 4000 24port 101001000 Module RJ45 REFURBISHED

    Yes it you get the refurbished with the good one then it would get detected and works fine.
    BTW- This module is EOL /EOS and below is the replacement part for the same:
    http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-4500-series-switches/eol_c51_574038.html
    WS-X4424-GB-RJ45
     Catalyst 4500 24-port 10/100/1000 Module (RJ45)
    Replacement-PartWS-X4548-GB-RJ45
     Catalyst 4500 Enhanced 48-Port 10/100/1000 Base-T (RJ-45)
    HTH
    Regards
    Inayath
    ***** Plz rate all usefull posts.

  • Password recovery at catalyst 4507R-E

    Hi. I have catalyst 4507R-E and 2 engines are located at this catalyst. the engines are active standby. when i begin to recover i write  the recover config at main engine then i must be reset the catalyst after reboot active engine go to satndby and standby go to active. so i can not recover it.
    how can i solve this?
    must i first remove standby engine and then recover active engine
    then put the standby and active engine configuration go to standby.
    am i rigth? i am afraid the i lost the configuration because i have not backup configuration.
    i used this PDF.
    please write your comment.
    thank you very much.

    Hi teymur,
    You never lost your configuration, what you need to do is...
    1. Make a complete config synch between active and standby supervisor engine (I hope autosync is already enabled)
    2. Write the config to NVRAM on standby supervisor engine.
    3. Now when you put back the standby supervisor engine, reload the active supervisor engine whcih take the standby be active and active be standby.
    Also I would like to infor the password recovery procedure for you...
    Try the below procedure with only one supervisor in the chassis.
    1) Connect the console cable to the Supervisor IV console port
    2) Reset the 4507 by power cycling the unit.
    3) Interrupt the boot sequence by hitting CTRL+C
    4) Using the confreg command, I set it to skip the boot-up configuration.
    5) I issue the reset command to reboot the 4507 again.
    http://www.cisco.com/en/US/products/hw/switches/ps663/products_password_recovery09186a00800945f7.shtml
    Please rate the helpful posts.
    Regards,
    Naidu.

  • Cisco Catalyst 4507R+E with WS-X4748 blade, ports not working

    I have a Cisco Catalyst 4507R+E  (with Sup7-E) and two blades; one WS-X4748-RJ45V+E and one WS-X4648-RJ45-E.
    When I connect a device to a port on the WS-X4748-RJ45V+E blade the port will not come up, show interface shows the status as "notconnect". When I connect the same device to the WS-X4648-RJ45-E blade the interface comes up.
    The WS-X4748-RJ45V+E blade seems to have initialised okay, it appears in the output of "show module" as OK.
    I get exactly the same effect on a second, identically configured Catalyst 4507R+E.
    The software version is IOS XE 3.1.0SG, which according to the release notes supports the WS-X4748-RJ45V+E blade. Has anybody else seen anything like this?

    I have 2 Core switches, single SUP on each.
    Line cards #1 and #2 randomly stop forwarding packets, only solution is to reload the switch ( hw-module reset does not work ). I have cat4500e-universalk9.SPA.03.05.00.E.152-1.E.bin and the sympton looks the same as the described one,
    although the code is newer than 3.2.2SG.
    Now we are downgrading to cat4500e-universalk9.SPA.03.04.02.SG.151-2.SG2.bin to check if that solves the issue,
    otherwise we´ll try removing/re-inserting the modules, and if issue persists, most probably RMA the Core1.
    We´ve sent a show tech to Cisco support while the issue was happening.
    Current modules on the Core switches.
    Mod Ports Card Type                              Model              Serial No.
    ---+-----+--------------------------------------+------------------+-----------
    1    48  10/100/1000BaseT EEE (RJ45)            WS-X4748-RJ45-E    CAT1627L48B
    2    48  10/100/1000BaseT EEE (RJ45)            WS-X4748-RJ45-E    CAT1629L0ZY
    3     4  Sup 7-E 10GE (SFP+), 1000BaseX (SFP)   WS-X45-SUP7-E      CAT1629L1PD
    5    12  1000BaseX (SFP)                        WS-X4612-SFP-E     JAE163007EO
    M MAC addresses                    Hw  Fw           Sw               Status
    --+--------------------------------+---+------------+----------------+---------
    1 30f7.0d57.80c0 to 30f7.0d57.80ef 1.1                               Ok      
    2 30f7.0dac.fd40 to 30f7.0dac.fd6f 1.1                               Ok      
    3 30f7.0dca.6c00 to 30f7.0dca.6c03 2.1 15.0(1r)SG10 03.05.00.E       Ok      
    5 a493.4c44.13e8 to a493.4c44.13f3 1.1                               Ok      
    Mod  Redundancy role     Operating mode      Redundancy status
    ----+-------------------+-------------------+----------------------------------
    3   Active Supervisor   SSO                 Active                           

  • Cisco Prime Infrastructure 2.2: Catalyst 2960X-24TS-LL Switch Collection Failure

    Hello,
    I've Upgraded Prime Infrastructure to Version 2.2.0.0.158. Now our Catalyst 2960X-24TS-LL switches show an error message, when they are added to the inventory. The error is as follows:
    Partial Collection Failure; Collection Status : Failed feature(s).
    The 2960X-24TS-LL is listed under the supported devices list and other switches (e.g. WS-C2960X-48FPS-L) got inventorized without any problems.
    Did anybody see this issue and can tell me how to solve it.
    - Benjamin

     - Getting that one too, since running 2.2 (Failed Features) ; suggest opening a TAC case.
    M.

  • Catalyst 4507R+E Clock Module

    Hi,
    I noticed that my 4507R+E chassis have the following module installed:
    WS-X4K-CLOCK-E
    I found in this EOL announcement that it's the clock module for 4507R-E chassis and is EoS since 2013:
    http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-4500-series-switches/eol_C51-715893.html
    Why the same module is installed in the new chassis and there are no spare parts available ?
    Thanks,
    Aron

    This catalyst 4507R-E whit this Supervisor Supervisor II+ WS-X4013+ suppourt thos module WS-X4648-RJ45V+E ?
    No, your supervisor only supports classic linecards but the WS-4648-RJ45V+E is not a classic line card so it is not supported. Have a look at this link and refer to Table 1 which shows which supervisors you could use with this card -
    http://www.cisco.com/en/US/prod/collateral/modules/ps2710/ps5494/product_data_sheet0900aecd802109ea.html
    Jon

  • Recommended IOS XE version for Cisco Catalyst 4500X-16 SFP+ Switch

    Could someone confirm IOS XE version for Cisco Catalyst 4500X-16 SFP+ Switch please.
    It already has 03.06.00.E on it. I am planning to configure VSS on it with similar switch.
    VSS will participate in various Etherchannels (MES).
    Just wondering if there are any known bugs in this IOS XE release.

    Use the Bug Search Tool to look for issues with vss, vsl, etc.
    https://tools.cisco.com/bugsearch/

  • Officejet pro 8600 plus power switch light stays on while in sleep mode. is this correct?

    officejet  pro 8600 plus  power switch light stays on while in sleep mode. is this correct?
    This question was solved.
    View Solution.

    The power light will slowly flash on and off when the Officejet Pro 8600 Plus is in a sleep mode state.
    -------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
    I am not an HP employee.

  • I need online Configuration Guide for Catalyst Express 500 Series Switches

    Hi Mates,
    Please is there an online help page for 500 series catalyst
    I have this one for IOS 12.2(25)FY http://www.cisco.com/en/US/products/ps6545/products_configuration_example09186a00806da6c9.shtml
    but I need more detailes like IOS 12.3(7)JA for Aironet 1300 http://www.cisco.com/en/US/products/ps5861/products_configuration_guide_book09186a00804ebd50.html
    Regards
    Saher

    I'm afraid there is not such document for IOS 12.2(25)FY since the Catalyst Express 500 Series switches are manageable through the GUI Device Manager or Cisco Network Assistant.
    I have also found key features and standards supported for that release:
    http://www.cisco.com/en/US/products/sw/iosswrel/ps5012/prod_bulletin0900aecd8033b8b3.html
    Hope this helps

  • Last version Cisco Catalyst 2960-24PC-L Switch (bugs study)

    Hi team,
          I need know, what´s  the last IOS version to Cisco Catalyst 2960-24PC-L Switch and understand the bug study about these versions?
    How make a bug study?
    If you have any information, please let me know.
    Regards,
    Yerko.

    Latest release as of January 14th is 15.0.2-SE5 (Release Nov 6, 2013)
    There aren't any public utilities in the Cisco website that provides you with a bug study.
    We have a bug tracker https://tools.cisco.com/bugsearch/?referring_site=popular but it will be extremely time consuming to identify each bugs and if you are affected.
    If you are a Cisco Advanced customer with optimization services in your contract, this deliverable can be done for you at no cost.

  • Monitoring Catalyst Switch (MIB issue)

    Hello,
    I am trying to monitor Catalyst WS-C3750G-24TS-E switches with Openview NNM. Before being able to do this, I have of course to import the MIB in Openview in order to interprete the traps, MIB entries,... that I get from/look at the switch.
    In the Management part of the datasheet of the switch, there is a list of about 20 MIB's, does this mean that I have to import all these MIBs in NNM in order to be able to monitor the switch??
    (I have the same issue also for Catalyst WS-4506 Chassis, WS-X4548-GB-RJ45 48x10/100/1000T ports blade an for the loadbalancer CSS11501, but probably the response for the catalyst will respond also the questions)
    Best regards
    CB

    Thanx for your reply.
    In fact, the core functionning of SNMP traps, requests is clear for me, perhaps I was not clear enough on that :-). What I need to know is if importing a single MIB allows me to interpret all the information that I get from the switch(all the traps and gets) or do I need to import all the MIBs that are indicated in the whitepaper. I could imagine that most of the MIBs contain redundant information so there would be no need in importing them all, but I am not sure on this point.
    Thanx
    CB

  • VLAN routing on Catalyst plus external WAN router issue......

    Hi,
    Bit of advice if possible.
    I've got a project to implement VLAN's on a MAN, which is easy enough, using CAT4506 and a mixture of 3750 and 2950 switches. The Vlan aspect is OK but I'm a bit unsure as to how to integrate the WAN into the design.
    I have two core WAN access sites each with 2 * cat4506 switches of which one at each site attach to a WAN router (3725)
    The CAT4506 switches will be doing the vlan routing but the 3725 routers (one at each site in a HSRP group) will be routing the WAN. Obviously these need to be attached to the catalysts for WAN access. As I have seperate routers for vlan routing and wan routing, what is the best way to configure this ?????
    Is configuring a seperate VLAN for the routers the best idea ? or is it best to use the sub interface option on the router ethernet ports ?
    Do I just use a static route of last resort on the Catalyst pointing to the routers ?
    Help :-)

    When you arte still in the design-phase, I want to strongly discourage you from designing a network with vlans that span multiple sites.
    You will always run int STP issues in one way or another. The following link will give some sensible information on this subject:
    http://www.cisco.com/en/US/netsol/ns340/ns394/ns147/ns17/networking_solutions_white_paper09186a00800a3e16.shtml
    I hope that it will point you to the right (or at leats an optimal) solution for your specific design.
    Regards,
    Leo

  • LMS 3.1 Device Discovery issue

    Hello,
    I have been getting myself familiar with LMS, but can't figure out why I am having issues seeing some devices. I can't find any solution to my problem on other posts.
    I have a server farm connected to my core switch, both can see each other via CDP, and the SF can ping the LMS server. However, I have 'device unreachable' on device discovery and CiscoView. SNMP community strings are the same on each device, and are configured on LMS.
    Any suggestions? Thanks in advance!

    Hi,
    LMS tries to contact each device directly via SNMP. If it can talk directly to the device, the device is added into DCR as Reachable. If it cannot talk directly to the device, the device is deemed as Unreachable and it is not added into DCR to be managed by LMS.
    If LMS is unable to communicate it could be due to any number of things including timeout, incorrect community string, snmp-server view, firewall or access list.
    A definitive way to determine the issue would be to perform a packet capture during discovery to see the SNMP transaction between LMS and an 'unreachable' device.
    You can also try increasing the timeout value.
    Thanks.

  • HP OfficeJet Pro 8600 Plus - "Scan to Computer" issue on Mac OSX 10.8 or 10.9

    Hi...
    I have started experiencing the notorious "scan to computer not working" issue on my 1-month OfficeJet Pro 8600 Plus, after having used the feature a number of times flawlessly.
    There are a lot of potential solutions mentioned in dozens of relevant posts for both Mac and Windows, e.g.:
    "Failed to open a session on the device"...
    Scan to computer does not work...
    Problem scanning to computer with an 8600 wireless
    Unable to enable print to computer...
    Enable Scan to Computer - Communication Error
    Officejet Pro 8600 Utility does not show my Mac computer in scan settings
    A 'Connection Error' or 'No Computer Detected' Error Message Displays during Scanning
    HP Wireless All-in-One Printers - Communication Error between the Scanner and Your Computer...
    Etc.
    However, in my case, no solution works, after several frustrating hours of trying to fix the issue, in Mac OS X Mountain Lion (10.8), or after upgrading to Maverics (10.9).
    The behavior of the device points to a software issue, since:
    The printer is visible on the network
    The print function has been working fine
    The HP Scan function works
    The generic Scan function from System Preferences works (although in earlier times it did not, or it stopped working soon after invoking it)
    The "Scan to Computer" option does not appear in the HP Utility screen (although occasionally, after random sequences of unistalling and installing the software, it reappears)
    The HP Installer crashes before completing the installation (this is a latest symptom, apparently happening before unvoking the HP Setup Assistant, which still works fine)
    As already mentioned, I have tried all possible solutions, including software and firmware updates, Apple drivers, HP drivers (full featured software), clean (un)installations, followed by computer and printer restarts. Nothing seems to work.
    The "Scan to Computer" feature of the 8600 always works on my Windows 7 laptop, after initial configuration. 
    The next step will be returning the device for a refund, but before resorting to that, I am giving it a last chance, in (the unlikely) case there is something new I have not tried yet.
    Thanks,
    PNS

    facman
    I am linking you to an HP Support document titled “Uninstalling the Printer Software” below. I am also providing you the link to the HP software for your printer titled “HP Officejet Pro Full Feature Software and Driver - Mac OS X 10.6, OS X 10.7, OS X 10.8” below as well.
    Follow the first document and uninstall the software. Reboot the computer than download and install the linked software. This should resolve your issue.
    Uninstalling the Printer Software
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c02259020
    HP Officejet Pro Full Feature Software and Driver - Mac OS X 10.6, OS X 10.7, OS X 10.8
    http://ftp.hp.com/pub/softlib/software12/COL44234/mp-107214-1/Officejet-Pro-8600_v12.23.0.dmg
    Please feel free to re-post if you have any further questions or concerns we are here to help.
    Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
    Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
    Dunidar
    I work on behalf of HP
    Find out a bit more about me by checking out my profile!
    "Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Maybe you are looking for