Catalyst 4900M and Catalyst 2960S-48FPS-L interconnection

I have Catalyst 4900M as distribution level and several Catalyst 2960S-48FPS-L as access devices.
I am going to use "WS-X4908-10GE 8 Port 10 Gigabit Module Switch"
With CVR-X2-SFP10G converter module I can get 10Gig on optical ports from Catalyst 4900M side, but Catalyst 2960S-48FPS-L support only 1 Gig optical standard on their SFP ports. Will it work (optical 10Gig<->1Gig) or any other suggestions?

You've got an X2 port, don't you? If you do, then why don't you purchase a TwinGig converter.
The Cisco TwinGig Converter Module (below) converts a single 10 Gigabit Ethernet X2 interface into two Gigabit Ethernet port slots that can be populated with SFP optics, enabling customers to use Gigabit Ethernet SFPs on the same card in combination with 10 Gigabit Ethernet X2 optics.

Similar Messages

[SOLVED] catalyst-daemon and catalyst-hook are in conflict

hi
i want upgrade my system , but i see catalyst-hook and catalyst-daemon are in conflict and uneasy not install daemon and hook on system , so what can i do ?
[root@WhiteCrow1 arash]# pacman -Syu
:: Starting full system upgrade...
:: Replace catalyst with catalyst/catalyst-daemon? [Y/n] y
:: Replace catalyst with catalyst/catalyst-generator? [Y/n] y
:: Replace catalyst with catalyst/catalyst-hook? [Y/n] y
resolving dependencies...
looking for inter-conflicts...
error: unresolvable package conflicts detected
error: failed to prepare transaction (conflicting dependencies)
:: catalyst-daemon and catalyst-hook are in conflict
Last edited by arastoo.s (2011-02-13 14:04:57)

As far as I know catalyst-daemon and catalyst-hook provide the same module so they are in conflict. The difference is that catalyst-daemon uses a daemon at startup to check for a new kernel and compile a new module when needed. Catalyst-hook does the same thing with a hook.
I picked the daemon method and just answered no to replace with -hook or -generator (catalyst-generator also conflicts with the others). Just choose the one you like.
https://wiki.archlinux.org/index.php/AT … D_packages

Interconnecting Catalyst 3750 and 2948G-L3

I am trying to interconnect a Catalyst 3750 and a 2948G-L3 using fiber GBIC. The interfaces where the GBIC and fiber are attached show up as physically down. I have tried different ports and also changed both switches. No Luck. If I connect a 3524 to the 3750 using the same connection it works.
Are 2948G-L3 switches compatible with the 3750?
Thanks,
VT

Should have no problem. Can you try the following on the 3750's gig interface:
speed nonegotiate
See of the link comes up.
Please rate all posts.

EtherChannel between 6006 (catos) and Catalyst 2960 HELP

Hi All,
I want to create an etherchannel between 6006 (catos) and Catalyst 2960 to have failover and load balace.
My ports on 6006 (catos) 6/37,6/47 and on 2960 giga 0/1 and giga 0/2.
I have checked on 6006 it supports channel.
Please help to configure this.
Thanks,
AS

AS
Use this doc as a guide and if you have further questions please come back -
http://www.cisco.com/en/US/tech/tk389/tk213/technologies_configuration_example09186a0080094953.shtml#specialconsid
Jon

Catalyst 4900M OneX & Twinax

I am trying to connect a Nexus 5548UP to a Catalyst 4900M using Twinax.
On the 4900M I am using a OneX converter (CVR-X2-SFP10G) to provide me with the necessary SFP+ port. I am using a 3m Twinax for the link (
SFP-H10GB-CU3M=)
The 4900M recognizes the OneX but does not recognize the Twinax. If I switch to using 10GB-SR fiber SFPs everything works, but we are trying to move exclusively to Twinax.
I found a post from 2009 (here) which mentioned some compatibility issues with Twinax on the 4900M with OneX and that the poster was working with Cisco. Does this incompatibility still exist? Both the 4900M and Twinax are on the compatibility matrix for the OneX module.
Thanks!

this needs a v -02 twinax cable. possibly we have a older version twinax and that might wont work.
http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6974.pdf
please look at table 5 and the note below it.
Thanks, Vin

[Solved] XServer 1.13 and Catalyst...

Hi, after the last update i can't start my xserver.
Systemd says, that gdm starts fine but i can't see anything except my tty
Heres the Xorg.0.log:
[ 170.848]
X.Org X Server 1.13.0
Release Date: 2012-09-05
[ 170.878] X Protocol Version 11, Revision 0
[ 170.888] Build Operating System: Linux 3.6.0-1-ARCH x86_64
[ 170.899] Current Operating System: Linux arch247 3.5.6-1-ARCH #1 SMP PREEMPT Sun Oct 7 19:30:49 CEST 2012 x86_64
[ 170.899] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=7f15c92f-c86f-49dd-ab06-f89a4a37d526 ro init=/usr/lib/systemd/systemd nomodeset
[ 170.924] Build Date: 05 October 2012 01:57:18PM
[ 170.937]
[ 170.949] Current version of pixman: 0.26.2
[ 170.976] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 170.976] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 171.033] (==) Log file: "/var/log/Xorg.0.log", Time: Sat Oct 13 18:30:14 2012
[ 171.049] (==) Using config file: "/etc/X11/xorg.conf"
[ 171.064] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 171.064] (==) ServerLayout "aticonfig Layout"
[ 171.064] (**) |-->Screen "aticonfig-Screen[0]-0" (0)
[ 171.064] (**) | |-->Monitor "aticonfig-Monitor[0]-0"
[ 171.064] (**) | |-->Device "aticonfig-Device[0]-0"
[ 171.064] (==) Automatically adding devices
[ 171.064] (==) Automatically enabling devices
[ 171.064] (==) Automatically adding GPU devices
[ 171.065] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 171.065] Entry deleted from font path.
[ 171.065] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 171.065] Entry deleted from font path.
[ 171.065] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 171.065] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 171.065] Entry deleted from font path.
[ 171.065] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 171.065] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/Type1/
[ 171.065] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 171.065] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 171.065] (II) Loader magic: 0x7fcc20
[ 171.065] (II) Module ABI versions:
[ 171.065] X.Org ANSI C Emulation: 0.4
[ 171.065] X.Org Video Driver: 13.0
[ 171.065] X.Org XInput driver : 18.0
[ 171.065] X.Org Server Extension : 7.0
[ 171.068] (--) PCI:*(0:0:1:0) 1002:9802:1043:84a5 rev 0, Mem @ 0xc0000000/268435456, 0xfeb00000/262144, I/O @ 0x0000f000/256
[ 171.068] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 171.084] Initializing built-in extension Generic Event Extension
[ 171.099] Initializing built-in extension SHAPE
[ 171.114] Initializing built-in extension MIT-SHM
[ 171.130] Initializing built-in extension XInputExtension
[ 171.145] Initializing built-in extension XTEST
[ 171.160] Initializing built-in extension BIG-REQUESTS
[ 171.175] Initializing built-in extension SYNC
[ 171.190] Initializing built-in extension XKEYBOARD
[ 171.205] Initializing built-in extension XC-MISC
[ 171.220] Initializing built-in extension SECURITY
[ 171.235] Initializing built-in extension XINERAMA
[ 171.250] Initializing built-in extension XFIXES
[ 171.265] Initializing built-in extension RENDER
[ 171.280] Initializing built-in extension RANDR
[ 171.295] Initializing built-in extension COMPOSITE
[ 171.311] Initializing built-in extension DAMAGE
[ 171.326] Initializing built-in extension MIT-SCREEN-SAVER
[ 171.342] Initializing built-in extension DOUBLE-BUFFER
[ 171.358] Initializing built-in extension RECORD
[ 171.374] Initializing built-in extension DPMS
[ 171.390] Initializing built-in extension X-Resource
[ 171.406] Initializing built-in extension XVideo
[ 171.422] Initializing built-in extension XVideo-MotionCompensation
[ 171.439] Initializing built-in extension XFree86-VidModeExtension
[ 171.455] Initializing built-in extension XFree86-DGA
[ 171.472] Initializing built-in extension XFree86-DRI
[ 171.489] Initializing built-in extension DRI2
[ 171.489] (II) "glx" will be loaded by default.
[ 171.489] (II) LoadModule: "glx"
[ 171.489] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 171.490] (II) Module glx: vendor="Advanced Micro Devices, Inc."
[ 171.490] compiled for 6.9.0, module version = 1.0.0
[ 171.507] Loading extension GLX
[ 171.507] (II) LoadModule: "fglrx"
[ 171.508] (II) Loading /usr/lib/xorg/modules/drivers/fglrx_drv.so
[ 171.538] (II) Module fglrx: vendor="FireGL - AMD Technologies Inc."
[ 171.538] compiled for 1.4.99.906, module version = 9.0.2
[ 171.538] Module class: X.Org Video Driver
[ 171.538] (II) Loading sub module "fglrxdrm"
[ 171.538] (II) LoadModule: "fglrxdrm"
[ 171.539] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[ 171.539] (II) Module fglrxdrm: vendor="FireGL - AMD Technologies Inc."
[ 171.539] compiled for 1.4.99.906, module version = 9.0.2
[ 171.539] (II) AMD Proprietary Linux Driver Version Identifier:9.00.2
[ 171.539] (II) AMD Proprietary Linux Driver Release Identifier: 9.00.11
[ 171.539] (II) AMD Proprietary Linux Driver Build Date: Sep 20 2012 11:56:16
[ 171.539] (--) using VT number 2
[ 171.649] (WW) Falling back to old probe method for fglrx
[ 171.660] (II) Loading PCS database from /etc/ati/amdpcsdb /etc/ati/amdpcsdb.default
[ 171.663] ukiDynamicMajor: found major device number 251
[ 171.663] ukiDynamicMajor: found major device number 251
[ 171.663] ukiOpenByBusid: Searching for BusID PCI:0:1:0
[ 171.663] ukiOpenDevice: node name is /dev/ati/card0
[ 171.663] ukiOpenDevice: open result is 9, (OK)
[ 171.663] ukiOpenDevice: Get driver state failed
[ 171.663] ukiOpenByBusid: ukiOpenMinor returns 9
[ 171.664] ukiOpenByBusid: ukiGetBusid reports PCI:0:1:0
[ 171.665] (--) Chipset Supported AMD Graphics Processor (0x9802) found
[ 171.666] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:1:1) found
[ 171.666] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:17:0) found
[ 171.666] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:18:0) found
[ 171.666] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:18:2) found
[ 171.666] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:19:0) found
[ 171.666] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:19:2) found
[ 171.666] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:0) found
[ 171.666] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:2) found
[ 171.666] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:3) found
[ 171.666] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:4) found
[ 171.666] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:20:5) found
[ 171.666] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:21:0) found
[ 171.666] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:21:1) found
[ 171.666] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:21:2) found
[ 171.666] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:21:3) found
[ 171.666] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:22:0) found
[ 171.666] (WW) fglrx: No matching Device section for instance (BusID PCI:0@0:22:2) found
[ 171.668] (II) AMD Video driver is running on a device belonging to a group targeted for this release
[ 171.668] (II) AMD Video driver is signed
[ 171.669] (II) fglrx(0): pEnt->device->identifier=0x165d5a0
[ 171.669] (II) fglrx(0): === [xdl_xs113_atiddxPreInit] === begin
[ 171.670] (II) Loading sub module "vgahw"
[ 171.670] (II) LoadModule: "vgahw"
[ 171.670] (II) Loading /usr/lib/xorg/modules/libvgahw.so
[ 171.670] (II) Module vgahw: vendor="X.Org Foundation"
[ 171.670] compiled for 1.13.0, module version = 0.1.0
[ 171.670] ABI class: X.Org Video Driver, version 13.0
[ 171.670] (**) fglrx(0): Depth 24, (--) framebuffer bpp 32
[ 171.670] (II) fglrx(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
[ 171.670] (==) fglrx(0): Default visual is TrueColor
[ 171.670] (**) fglrx(0): Option "DPMS" "true"
[ 171.671] (==) fglrx(0): RGB weight 888
[ 171.671] (II) fglrx(0): Using 8 bits per RGB
[ 171.671] (==) fglrx(0): Buffer Tiling is ON
[ 171.671] (II) Loading sub module "fglrxdrm"
[ 171.671] (II) LoadModule: "fglrxdrm"
[ 171.671] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[ 171.671] (II) Module fglrxdrm: vendor="FireGL - AMD Technologies Inc."
[ 171.671] compiled for 1.4.99.906, module version = 9.0.2
[ 171.674] ukiDynamicMajor: found major device number 251
[ 171.675] ukiDynamicMajor: found major device number 251
[ 171.675] ukiOpenByBusid: Searching for BusID PCI:0:1:0
[ 171.675] ukiOpenDevice: node name is /dev/ati/card0
[ 171.675] ukiOpenDevice: open result is 12, (OK)
[ 171.675] ukiOpenDevice: Get driver state failed
[ 171.675] ukiOpenByBusid: ukiOpenMinor returns 12
[ 171.675] ukiOpenByBusid: ukiGetBusid reports PCI:0:1:0
[ 171.675] (EE) fglrx(0): The graphics processor is already set to console mode, set X mode fail. Cannot start X.
[ 171.675] (EE) fglrx(0): PreInit failed
[ 171.675] (II) fglrx(0): === [xdl_xs113_atiddxPreInit] === end
[ 171.683] SetVBEMode failed
[ 171.683] (II) UnloadModule: "fglrx"
[ 171.683] (II) UnloadSubModule: "fglrxdrm"
[ 171.683] (II) Unloading fglrxdrm
[ 171.683] (II) UnloadSubModule: "vgahw"
[ 171.683] (II) Unloading vgahw
[ 171.683] (II) UnloadSubModule: "fglrxdrm"
[ 171.683] (EE) Screen(s) found, but none have a usable configuration.
[ 171.683]
Fatal server error:
[ 171.683] no screens found
[ 171.683] (EE)
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 171.684] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 171.684] (EE)
[ 171.920] Server terminated with error (1). Closing log file.
Xserver is at version 1.13, catalyst should be at version 12.9
The xorg.conf-file was generated through aticonfig --inital and worked before the update. While searching the net i came across /etc/dbus-1/gdm.conf, maybe its a permission-problem?
Any help is appreciated
Last edited by D4ve (2012-10-13 21:31:54)

Had also a problem with xorg 1.13 and catalyst. (just not gdm but slim).
I found this:
The main graphics drivers have already been updated to support the new API. The proprietary NVIDIA graphics driver has also been updated for the X.Org Server 1.13 ABI. The only common driver not yet supporting this new xorg-server release is the AMD Catalyst binary driver, but the API/ABI support should be there within a few months.
Source: http://www.phoronix.com/scan.php?page=n … px=MTE3Njg
Seems that is the reason.
In this topic [1] Vi0L0 said that catalyst-test from AUR works with xorg 1.13 from [testing]. I didn't test that. I just downgraded xorg-server, xorg-server-common, catalyst-utils, lib32-catalyst-utils (and xf86-input-evdev because the newest package has always dep. to the newest xorg-server).
[1] https://bbs.archlinux.org/viewtopic.php … 0#p1172200
My package versions are (after downgrading):
xorg-server 1.12.4-1
xorg-server-common 1.12.4-1
catalyst 12.8-2
catalyst-utils 12.8-2
lib32-catalyst-utils 12.8-2
Edit: I just realised that there is a new catalyst package (catalyst-dkms) on the [community], i always used the package from the [catalyst] repo (Server = http://catalyst.apocalypsus.net/repo/catalyst/$arch).
Last edited by sysrmr (2012-10-13 18:37:54)

Compton, Openbox and Catalyst 14

Hi.
I'm new with Arch Linux, Openbox and Compton, so...
I install compton and after that ATI driver... when I do that...the screen freeze and I can't see what I type/click, but if I kill the process (CTRL+ATL+F2, ps aux, kill -9...), everything is back again.
I use the Vi0L0's catalyst, and the compton.conf you can see below.
How can I fix that, for enable transparency, shadow and of course: Steam.
# Backend
# Backend to use: "xrender" or "glx".
# GLX backend is typically much faster but depends on a sane driver.
backend = "glx";
# GLX backend
glx-no-stencil = true;
# GLX backend: Copy unmodified regions from front buffer instead of redrawing them all.
# My tests with nvidia-drivers show a 10% decrease in performance when the whole screen is modified,
# but a 20% increase when only 1/4 is.
# My tests on nouveau show terrible slowdown.
# Useful with --glx-swap-method, as well.
glx-copy-from-front = false;
# GLX backend: Use MESA_copy_sub_buffer to do partial screen update.
# My tests on nouveau shows a 200% performance boost when only 1/4 of the screen is updated.
# May break VSync and is not available on some drivers.
# Overrides --glx-copy-from-front.
# glx-use-copysubbuffermesa = true;
# GLX backend: Avoid rebinding pixmap on window damage.
# Probably could improve performance on rapid window content changes, but is known to break things on some drivers (LLVMpipe).
# Recommended if it works.
# glx-no-rebind-pixmap = true;
# GLX backend: GLX buffer swap method we assume.
# Could be undefined (0), copy (1), exchange (2), 3-6, or buffer-age (-1).
# undefined is the slowest and the safest, and the default value.
# copy is fastest, but may fail on some drivers,
# 2-6 are gradually slower but safer (6 is still faster than 0).
# Usually, double buffer means 2, triple buffer means 3.
# buffer-age means auto-detect using GLX_EXT_buffer_age, supported by some drivers.
# Useless with --glx-use-copysubbuffermesa.
# Partially breaks --resize-damage.
# Defaults to undefined.
glx-swap-method = "undefined";
# Shadows
# Enabled client-side shadows on windows.
shadow = true;
# Don't draw shadows on DND windows.
no-dnd-shadow = true;
# Avoid drawing shadows on dock/panel windows.
no-dock-shadow = true;
# Zero the part of the shadow's mask behind the window. Fix some weirdness with ARGB windows.
clear-shadow = true;
# The blur radius for shadows. (default 12)
shadow-radius = 5;
# The left offset for shadows. (default -15)
shadow-offset-x = -5;
# The top offset for shadows. (default -15)
shadow-offset-y = -5;
# The translucency for shadows. (default .75)
shadow-opacity = 0.5;
# Set if you want different colour shadows
# shadow-red = 0.0;
# shadow-green = 0.0;
# shadow-blue = 0.0;
# The shadow exclude options are helpful if you have shadows enabled. Due to the way compton draws its shadows, certain applications will have visual glitches
# (most applications are fine, only apps that do weird things with xshapes or argb are affected).
# This list includes all the affected apps I found in my testing. The "! name~=''" part excludes shadows on any "Unknown" windows, this prevents a visual glitch with the XFWM alt tab switcher.
shadow-exclude = [
"! name~=''",
"name = 'Notification'",
"name = 'Plank'",
"name = 'Docky'",
"name = 'Kupfer'",
"name = 'xfce4-notifyd'",
"name *= 'VLC'",
"name *= 'compton'",
"name *= 'Chromium'",
"name *= 'Chrome'",
"name *= 'Firefox'",
"class_g = 'Conky'",
"class_g = 'Kupfer'",
"class_g = 'Synapse'",
"class_g ?= 'Notify-osd'",
"class_g ?= 'Cairo-dock'",
"class_g ?= 'Xfce4-notifyd'",
"class_g ?= 'Xfce4-power-manager'"
# Avoid drawing shadow on all shaped windows (see also: --detect-rounded-corners)
shadow-ignore-shaped = false;
# Opacity
menu-opacity = 1;
inactive-opacity = 1;
active-opacity = 1;
frame-opacity = 1;
inactive-opacity-override = false;
alpha-step = 0.06;
# Dim inactive windows. (0.0 - 1.0)
# inactive-dim = 0.2;
# Do not let dimness adjust based on window opacity.
# inactive-dim-fixed = true;
# Blur background of transparent windows. Bad performance with X Render backend. GLX backend is preferred.
# blur-background = true;
# Blur background of opaque windows with transparent frames as well.
# blur-background-frame = true;
# Do not let blur radius adjust based on window opacity.
blur-background-fixed = false;
blur-background-exclude = [
"window_type = 'dock'",
"window_type = 'desktop'"
# Fading
# Fade windows during opacity changes.
fading = true;
# The time between steps in a fade in milliseconds. (default 10).
fade-delta = 4;
# Opacity change between steps while fading in. (default 0.028).
fade-in-step = 0.03;
# Opacity change between steps while fading out. (default 0.03).
fade-out-step = 0.03;
# Fade windows in/out when opening/closing
# no-fading-openclose = true;
# Specify a list of conditions of windows that should not be faded.
fade-exclude = [ ];
# Other
# Try to detect WM windows and mark them as active.
mark-wmwin-focused = true;
# Mark all non-WM but override-redirect windows active (e.g. menus).
mark-ovredir-focused = true;
# Use EWMH _NET_WM_ACTIVE_WINDOW to determine which window is focused instead of using FocusIn/Out events.
# Usually more reliable but depends on a EWMH-compliant WM.
use-ewmh-active-win = true;
# Detect rounded corners and treat them as rectangular when --shadow-ignore-shaped is on.
detect-rounded-corners = true;
# Detect _NET_WM_OPACITY on client windows, useful for window managers not passing _NET_WM_OPACITY of client windows to frame windows.
# This prevents opacity being ignored for some apps.
# For example without this enabled my xfce4-notifyd is 100% opacity no matter what.
detect-client-opacity = true;
# Specify refresh rate of the screen.
# If not specified or 0, compton will try detecting this with X RandR extension.
refresh-rate = 0;
# Set VSync method. VSync methods currently available:
# none: No VSync
# drm: VSync with DRM_IOCTL_WAIT_VBLANK. May only work on some drivers.
# opengl: Try to VSync with SGI_video_sync OpenGL extension. Only work on some drivers.
# opengl-oml: Try to VSync with OML_sync_control OpenGL extension. Only work on some drivers.
# opengl-swc: Try to VSync with SGI_swap_control OpenGL extension. Only work on some drivers. Works only with GLX backend. Known to be most effective on many drivers. Does not actually control paint timing, only buffer swap is affected, so it doesn’t have the effect of --sw-opti unlike other methods. Experimental.
# opengl-mswc: Try to VSync with MESA_swap_control OpenGL extension. Basically the same as opengl-swc above, except the extension we use.
# (Note some VSync methods may not be enabled at compile time.)
vsync = "opengl-swc";
# Enable DBE painting mode, intended to use with VSync to (hopefully) eliminate tearing.
# Reported to have no effect, though.
dbe = false;
# Painting on X Composite overlay window. Recommended.
paint-on-overlay = true;
# Limit compton to repaint at most once every 1 / refresh_rate second to boost performance.
# This should not be used with --vsync drm/opengl/opengl-oml as they essentially does --sw-opti's job already,
# unless you wish to specify a lower refresh rate than the actual value.
sw-opti = false;
# Unredirect all windows if a full-screen opaque window is detected, to maximize performance for full-screen windows, like games.
# Known to cause flickering when redirecting/unredirecting windows.
# paint-on-overlay may make the flickering less obvious.
unredir-if-possible = true;
# Specify a list of conditions of windows that should always be considered focused.
focus-exclude = [ ];
# Use WM_TRANSIENT_FOR to group windows, and consider windows in the same group focused at the same time.
detect-transient = true;
# Use WM_CLIENT_LEADER to group windows, and consider windows in the same group focused at the same time.
# WM_TRANSIENT_FOR has higher priority if --detect-transient is enabled, too.
detect-client-leader = true;
# Window type settings
wintypes:
tooltip =
# fade: Fade the particular type of windows.
fade = true;
# shadow: Give those windows shadow
shadow = false;
# opacity: Default opacity for the type of windows.
opacity = 0.85;
# focus: Whether to always consider windows of this type focused.
focus = true;
Last edited by patrickmaciel (2014-07-26 22:07:58)

emeres wrote:Just wanted to make sure. It is also the regular one, not catalyst legacy, right?
I install that (from the arch wiki):
Once you have added some Catalyst repository, update pacman's database and install these packages (see #Tools for more information):
- catalyst-hook
- catalyst-utils
- catalyst-libgl
- opencl-catalyst - optional, needed for OpenCL support
- lib32-catalyst-utils - optional, needed for 32-bit OpenGL support on 64-bit systems
- lib32-catalyst-libgl - optional, needed for 32-bit OpenGL support on 64-bit systems
- lib32-opencl-catalyst - optional, needed for 32-bit OpenCL support on 64-bit systems
So... after that I get:
- Videos in browser (firefox/chrome/chromium) freeze in fullscreen
- Resize windows is slowly
- Teamviewer stop working
- Record screen stop working
- Sometimes I can't see what I'm typing... but after kill compton, everything appears
I try using default compton.conf and "no" compton.conf... same problem.
Sorry for my english
Last edited by patrickmaciel (2014-07-27 01:56:54)

No GLX on latest kernel, X, and catalyst

local/catalyst 11.7-1
local/catalyst-utils 11.6-1
local/lib32-catalyst-utils 11.6-1 (lib32)
local/xorg-server 1.10.3.901-1 (xorg)
local/linux 3.0.1-1 (base)
01:00.0 VGA compatible controller: ATI Technologies Inc RV770 [Radeon HD 4870]
[max@gayforcetwo Steam]$ glxinfo
name of display: :0.0
X Error of failed request: BadRequest (invalid request code or no such operation)
Major opcode of failed request: 136 (GLX)
Minor opcode of failed request: 19 (X_GLXQueryServerString)
Serial number of failed request: 18
Current serial number in output stream: 18
[max@gayforcetwo Steam]$ fglrxinfo
X Error of failed request: BadRequest (invalid request code or no such operation)
Major opcode of failed request: 136 (GLX)
Minor opcode of failed request: 19 (X_GLXQueryServerString)
Serial number of failed request: 18
Current serial number in output stream: 18
Section "ServerLayout"
Identifier "aticonfig Layout"
Screen 0 "aticonfig-Screen[0]-0" 0 0
EndSection
Section "Module"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]-0"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]-0"
Driver "fglrx"
BusID "PCI:1:0:0"
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]-0"
Device "aticonfig-Device[0]-0"
Monitor "aticonfig-Monitor[0]-0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
What's going on?
Last edited by synthead (2011-08-11 17:53:31)

I don't know how you updated, but I use the catalyst repository, and in the last big update, there was an issue in the order of installing linux 3 and catalyst 11.7 (?), such that the fglrx hook failed. I had to redo building the image, whereupon the hook worked. Did you check for messages as it rebuilt the image?
Sorry if this was obvious, but I am not arch-guts/catalyst savvy.
HTH

ATI Catalyst Install Manager and catalyst Control Center Help

I just run the Windows 7 Upgrade
advisor report and it said that I should uninstall the ATI Catalyst Install Manager and Catalyst Control Center then reinstall after upgrade..
Could someone direct me where I might t find these programs for Windows 7

You must not do this. Just continue upgrade installation.
On my Satellite I got the same message but I have simply continued with upgrade.
At the end everything went fine.

LMS 3.2 and Catalyst 4500 WS-X4648-RJ45-E module card

Hi all,
I have a rpoblem with a specific client with LMS 3.2. We are using LMS 3.2 on Windows 2008 and everything seem to be working OK. The issue is in the CiscoView with the 4500 switches. CiscoView can see the supervisors on all 4500 switches (6); but cannot see the switchcards when the switchcards are WS-X4648-RJ45-E. Find the sh inv output below:
CSR-D1#sh inventory
NAME: "Switch System", DESCR: "Cisco Systems, Inc. WS-C4507R-E 7 slot switch "
PID: WS-C4507R-E       , VID: V01, SN: FOX1152GKR1
NAME: "Clock Module", DESCR: "Clock Module"
PID: WS-X4K-CLOCK-E    , VID: V01, SN: JAE120354DD
NAME: "Linecard(slot 1)", DESCR: "10/100/1000BaseT (RJ45) with 48 10/100/1000 baseT "
PID: WS-X4648-RJ45-E   , VID: V01, SN: JAE14410NLT
NAME: "Linecard(slot 2)", DESCR: "6 Dual media SFP or 10/100/1000BaseT (RJ45)V voice power ports (Cisco/IEEE)"
PID: WS-X4506-GB-T     , VID: V05, SN: JAE120351NC
NAME: "Linecard(slot 3)", DESCR: "Supervisor 6-E 10GE (X2), 1000BaseX (SFP) with 2 10GE X2 ports"
PID: WS-X45-SUP6-E     , VID: V01, SN: JAE120576HG
NAME: "TenGigabitEthernet3/1", DESCR: "10Gbase-LRM"
PID: FTLX1341E2-C1     , VID: A , SN: FNS1352175M
NAME: "TwinGig Converter 3/2", DESCR: "TwinGig Converter Module"
PID: 800-27645-01      , VID: A0 , SN: CAT1147H2WK
NAME: "Linecard(slot 4)", DESCR: "Supervisor 6-E 10GE (X2), 1000BaseX (SFP) with 2 10GE X2 ports"
PID: WS-X45-SUP6-E     , VID: V07, SN: JAE14080NL2
NAME: "TwinGig Converter 4/2", DESCR: "TwinGig Converter Module"
PID: 800-27645-01      , VID: A0 , SN: CAT1147H2BV
NAME: "Linecard(slot 7)", DESCR: "10/100/1000BaseT (RJ45) with 48 10/100/1000 baseT "
PID: WS-X4648-RJ45-E   , VID: V01, SN: JAE14420A2F
I have updated the s/w to 12.2(53) SG1 with no luck.
Any ideas?

Hi Nicos,
I have exactly the same issue with LMS 3.2 CiscoView under Windows 2003 and catalyst switch 4506-E.
4506-E are in IOS 12.2(53)SG2.
I installed latest 4500IOS V 19.0 ciscoview device package without success.
Did you fix your problem ?

Does Cisco ISE 1.2 support Catalyst SRW224G4P and Small business ESW520 Switches?

Hello all,
Does Cisco ISE 1.2 support Catalyst SRW224G4P and Small business ESW520 Switches?
Best regards.

Hi there, the link below outlines the ISE supported Cisco hardware:
http://www.cisco.com/c/en/us/td/docs/security/ise/1-3/compatibility/ise_sdt.html
Thank you for rating helpful posts!

Xmonad, xorg 1.9, and catalyst-test

Hi guys,
I'm running xorg 1.9 and catalyst-test on my HP Envy 15 (which contains a Radeon Mobility 5830.) Almost everything works; nothing strange appears in /var/log/Xorg.log or glxinfo. It's clear that my hardware acceleration is fine because I'm getting 200+ FPS in Extreme Tux Racer.
However, xmonad, of all things, is super-slow. When I switch workspaces or spawn tiled windows, the redraw lag is quite visible and I can see my CPU spike.
Amid other reports of X problems, I tried installing the backclear/catalyst-maximize-fix xserver packages from the catalyst repository, but those didn't seem to help. I also tried flipping the bit to enable XAA 2D acceleration, and that didn't seem to help either.
Any ideas as to why X doesn't seem to be accelerating this properly?

Yeeees, catalyst isn't supporting xserver 1.10 atm. Maybe 11.3 will support it, maybe.
Workaround is to:
- add xorg-server-* and xf86-input-* packages which you installed into pacman.conf's IgnorePkg list
- OR use [xorg19] repo - read wiki .

Dacl on ACS 5.1 and Catalyst switch 3560

Dear all
I have ACS 5.1 and Catalyst switch 3560 with version 12.2(53)SE. I configure a dacl on the ACS and I use it on authorization profile.
This authrization profile is used on access policy.
I tried the authentication but it doesn't work. I checked the ACS logs and I found that the user is authenicated successfuly but the dacl gives this error (The Access-Request for the requested dACL is missing a cisco-av-pair attribute with the value aaa:event=acl-download. The request is rejected)
Steps:
11001 Received RADIUS Access-Request
11017 RADIUS created a new session
11025 The Access-Request for the requested dACL is missing a cisco-av-pair attribute with the value aaa:event=acl-download. The request is rejected
11003 Returned RADIUS Access-Reject
DACL:
deny ip host 1.2.3.4 1.2.3.0 0.0.0.255 log
permit ip any any log
Thanks on advance,

Dear Tiago
I applied the command "radius-server vsa send". Now I can see the dacl is applied but I can't see it on the switch and even the authentication is succueeded ont the ACS logs but it give me unauthoized on the switchport. You can see the logs( started with the username acstest and the access-list is applied but it doesn't work and you can see theat it goes for mab after eap timed out). I hope you can help on this issue.
Dec 13,10 10:29:00.513 AM
00-23-AE-7A-58-A6
00-23-AE-7A-58-A6
Default Network Access
Lookup
Dot1x-3560-Switch
1.2.3.4
FastEthernet0/5
TESTACS
22056 Subject not found in the applicable identity store(s).
Dec 13,10 10:28:29.186 AM
#ACSACL#-IP-Guest-4cfcc14d
Dot1x-3560-Switch
1.2.3.4
TESTACS
Dec 13,10 10:28:28.726 AM
acstest
00-23-AE-7A-58-A6
Default Network Access
PEAP (EAP-MSCHAPv2)
Dot1x-3560-Switch
1.2.3.4
FastEthernet0/5
TESTACS
Thanks,

Business Catalyst tools and services

is Business Catalyst tools and services included in Muse membership ?

Hello,
and if i want a blog service, i pay for the difference or the next bigger price bc membership ?
De : Gaurav Sharma [email protected]
Envoyé : 28 avril 2014 17:40
À : visiongrid
Objet : Business Catalyst tools and services
Re: Business Catalyst tools and services
created by Gaurav Sharma <http://forums.adobe.com/people/Gaurav.S> in Help with using Adobe Muse CC - View the full discussion <http://forums.adobe.com/message/6338716#6338716

Business Catalyst mail and ios7

My iphone and iPad email account will not verify. Have set up email with the same settings in Mac Mail and it works fine. I have tried resetting password.

Hello,
and if i want a blog service, i pay for the difference or the next bigger price bc membership ?
De : Gaurav Sharma [email protected]
Envoyé : 28 avril 2014 17:40
À : visiongrid
Objet : Business Catalyst tools and services
Re: Business Catalyst tools and services
created by Gaurav Sharma <http://forums.adobe.com/people/Gaurav.S> in Help with using Adobe Muse CC - View the full discussion <http://forums.adobe.com/message/6338716#6338716

Catalyst 4900M and Catalyst 2960S-48FPS-L interconnection

Similar Messages

Maybe you are looking for