Catos 7.4. losing config after reload

Hello,
A customer is having the following problem on severals sites.
After a reload, some cat6000-sup1a-withoutMSFC and some cat2948G all running release 7.4.3 lose some part (not all) of the configuration, after a reload.
Sometime the vlan configuration vanished, some other time the SNMP configuration disappeared.
Does anyone already get this kind of problem ?
I found no bug on the bug tools or on the RN for 7.4.x.
Regards,

Hello Prashanth,
On one cat6X00, the sh version from the sh tech do not show me any checksum failure, but I can find this on the "sh log" from the console port after a reload (and loosing some part of configuration):
Console> (enable) show logg buff 1023
2005 Aug 08 07:12:43 %SYS-4-NVLOG:check_block_and_log:Block 0 checksum failed: 0x2CCB(0x2CC9)
2005 Aug 08 07:12:52 %SYS-3-MOD_PORTINTFINSYNC:Port Interface in sync for Module 1
2005 Aug 08 07:12:54 %SYS-1-SYS_ENABLEPS: Power supply 1 enabled
2005 Aug 08 07:12:54 %SYS-1-SYS_ENABLEPS: Power supply 2 enabled
2005 Aug 08 07:12:54 %SYS-5-MOD_PWRON:Module 3 powered up
2005 Aug 08 07:12:55 %SYS-5-MOD_PWRON:Module 4 powered up
2005 Aug 08 06:12:57 %SYS-5-MOD_OK:Module 1 is online
2005 Aug 08 06:13:02 %DTP-5-TRUNKPORTON:Port 1/1 has become dot1q trunk
2005 Aug 08 06:13:02 %DTP-5-TRUNKPORTON:Port 1/2 has become dot1q trunk
2005 Aug 08 06:13:04 %ETHC-5-PORTTOSTP:Port 1/1 joined bridge port 1/1-2
2005 Aug 08 06:13:04 %ETHC-5-PORTTOSTP:Port 1/2 joined bridge port 1/1-2
2005 Aug 08 06:13:55 %SYS-5-MOD_OK:Module 3 is online
2005 Aug 08 06:13:55 %SYS-3-MOD_PORTINTFINSYNC:Port Interface in sync for Module 3
2005 Aug 08 06:13:56 %SYS-5-MOD_OK:Module 4 is online
2005 Aug 08 06:13:56 %SYS-3-MOD_PORTINTFINSYNC:Port Interface in sync for Module 4
So this cat6x00 could match this bug. Do you aggree with me ?
Best regards,

Similar Messages

Config Register Not changing after reload

Hi Al,
I am having an issue with a Cisco 3850 Catalyst switch, issue as below:
- Current config register is 0x142 and have configured the config register to 0x102 but even after reload the new config register does not come in place.
- Have reloaded the switch 2x but with no luck. Changed the config register on the primary and secondary switch yet no luck. It is running SSO.
Show version:
sh ver
Cisco IOS Software, IOS-XE Software, Catalyst L3 Switch Software (CAT3K_CAA-UNIVERSALK9-M), Version 03.03.02SE RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Thu 20-Feb-14 21:17 by prod_rel_team
Cisco IOS-XE software, Copyright (c) 2005-2014 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0.
(http://www.gnu.org/licenses/gpl-2.0.html) For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
BOOTLDR: CAT3K_CAA Boot Loader (CAT3K_CAA-HBOOT-M) Version 1.2, RELEASE SOFTWARE (P)
XXXX uptime is 1 day, 13 hours, 53 minutes
Uptime for this control processor is 1 day, 13 hours, 56 minutes
System returned to ROM by reload at 23:44:31 ADST Wed Feb 26 2014
System restarted at 23:50:23 ADST Wed Feb 26 2014
System image file is "flash:packages.conf"
Last reload reason: Reload command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
License Level: Lanbase
License Type: Permanent
Next reload license Level: Lanbase
9 Virtual Ethernet interfaces
56 Gigabit Ethernet interfaces
8 Ten Gigabit Ethernet interfaces
2048K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
250456K bytes of Crash Files at crashinfo:.
250456K bytes of Crash Files at crashinfo-2:.
1609272K bytes of Flash at flash:.
1609272K bytes of Flash at flash-2:.
0K bytes of Dummy USB Flash at usbflash0:.
0K bytes of Dummy USB Flash at usbflash0-2:.
0K bytes of at webui:.
Base Ethernet MAC Address          :
Motherboard Assembly Number        :
Motherboard Serial Number          :
Model Revision Number              :
Motherboard Revision Number        :
Model Number                       :
System Serial Number             :
Switch Ports Model              SW Version        SW Image              Mode
*    1 32    WS-C3850-24T       03.03.02SE        cat3k_caa-universalk9 INSTALL
     2 32    WS-C3850-24T       03.03.02SE        cat3k_caa-universalk9 INSTALL
Switch 02
Switch uptime                      : 1 day, 13 hours, 56 minutes
Base Ethernet MAC Address          :
Motherboard Assembly Number        :
Motherboard Serial Number          :
Model Revision Number              :
Motherboard Revision Number        :
Model Number                       : WS-C3850-24T
System Serial Number               :
Configuration register is 0x142 (will be 0x102 at next reload)

I have a 3850 switch with an identical issue. I have been unable to get the device to boot using the existing config .
I have the following output in 'sh ver'
Configuration register is 0x142 (will be 0x102 at next reload)
BUT the device does not reload with 0x102, at the next reload, but continues to exhibit identical behaviour after repeated reboots.
Kind regards

LMS 4.0.1 software distribution 3 out of 7 fail to pass traffic after reload

I've distributed (7) IOS C3560-ipbasek9-mz.150-1.SE2.bin upgrades on identical 3560G PS-S platform using LMS 4.0.1. All jobs come back successfully completed with the /MD5 hash matching exactly what Cisco has on their website. All devices have sufficient 32MB worth of Flash and verified enough was available prior to distribution.
Issue: After reload 2 of these 3560G devices would not pass traffic. Also, neighboring devices could see these devices through "show cdp neighbors detail" but the management IP was not being displayed. After consoling into these devices via (console port) the management IP address was there but was unable to ping this address locally and neighboring devices were unable to be pinged as well. Performed the "sh run" command and verified the config was correct.
***Cisco's engineers suggestion was to load a lower IOS.***
***I've perused the caveats with this release and have not found any solutions.***
I've already replaced the offending switches with new devices but don't want to keep upgrading with this many failures after reloading.

Your devices with the NX-OS versions you indicate should be OK per the LMS 4.0.1 Supported Devices Table.
Have you updated your LMS with the latest device packages? See the procedure here.

ACCESS POINTS LOSING CONFIG CAPWAP

I know there were a few post about users losing their access point config after a power loss to the ap. I wanted to share that I can confirm and reproduce this same issue with a number of access points that I have. I opened a tac case and will update this tread as the case progresses.
Wlc 5508
Ap 1242
7.0.220.0
Sent from Cisco Technical Support iPad App

You mean anything 5.x, no but I might have to .. So Im told a bug was open for this .. I will update thread as this progresses.
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin

What's wrong? Verify and compare Cisco 2901 config after loading old config from Cisco 2801

Hi Cisco Community / Friends,
I am new to this site though I have cisco account for many years. I am a CCNA ,I passed my certification on January 2013 I seldom use and utilized my skills on networking becuase of my type of work. I am Project Eng'r working in a System integrator company . Anyway, I would like to ask assistance on the configurations of my Cisco router for this gov't projects.. Here's the situation.
We have a new project for the VSAT Comm'n of Coast Watch Station , The VSAT was installed 7 years ago. The VSAT was only used for a year by this Gov't agency because of subscription issue. Now, they wants to revive and use their VSAT facilities for the Coast watch monitoring. Now, some of this routers are working up to now and for some site are already defective so I need to replace the old 2801 router with a new equivalent model which is Cisco 2901. My plan was just to load the old config into the new Cisco 2901 router. However, after loading it to the new router, I am a little worried because I've got some errors received. I load the old config by copying the old files, edit it in notepad, and load the config using Secure CRT (terminal emulator). When I copy the old config of cisco 2801 to new router cisco 2901 , below are the command not recognized on Cisco 2901. What's wrong ? What are these commands for?
Appreciate your comments and help on this matter.. Thank You very much
Note: I Attached the original config from Cisco 2801 and the other file is the config after I load the config file to Cisco 2901.
(Errors see below)
CWS_4_Pandami(config-erm)#mmi polling-interval 60
                         ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-erm)#no mmi auto-configure
                               ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-erm)#no mmi pvc
                               ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-erm)#mmi snmp-timeout 180
                                                        ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config-if)#interface GigabitEthernet0/1
CWS_4_Pandami(config-if)# description ===CWS4 SAT Modem===
CWS_4_Pandami(config-if)# bandwidth 256
CWS_4_Pandami(config-if)# ip address 192.168.42.1 255.255.255.0
CWS_4_Pandami(config-if)# duplex auto
CWS_4_Pandami(config-if)# speed auto
CWS_4_Pandami(config-if)# priority-group 1
                                                    ^
% Invalid input detected at '^' marker.
CWS_4_Pandami(config)#access-list 100 permit ip any any dscp cs5
CWS_4_Pandami(config)#priority-list 1 protocol ip high list 100
                          ^
% Invalid input detected at '^' marker.

Hi
From Cisco's website:
The Modem Management Interface (MMI) is software that enables auto-provisioning for the Cisco 827 routers. The MMI uses a fixed PVC to communicate with the Proxy Element (PE) residing on the digital subscriber line access multiplexer (DSLAM). Using MMI, the Cisco 827 router updates the running image and downloads the prescribed configuration using a configuration file or configuration values in a provisioning information database.
The customer premise equipment (CPE) can be automatically configured using the Cisco DSL CPE download, but it can be configured only with the image provisioning feature.
So because this is your device, you don't want to use MMI anyways.
And "priority-list" is QoS. Probably that QoS-command is old and removed, because now QoS is configured using class-maps and policy-maps.

I am unable to edit information I have typed into a spacebar, this includes backspace, and when I highlight it, even after reloading the page

I recently upgraded to Firefox 4 on my 3 yr old Macbook, though I am unsure if this is in fact connected. Now I am often unable to edit information I have typed into a search bar or text box (such as this one) even after reloading that page or pressing first the back, then the forward buttons. Has anyone else run into this, and does anyone know what is going on?

Start Firefox in [[Safe Mode]] to check if one of the add-ons is causing the problem (switch to the DEFAULT theme: Tools > Add-ons > Appearance/Themes).
* Don't make any changes on the Safe mode start window.
See:
* [[Troubleshooting extensions and themes]]
Create a new profile as a test to check if your current profile is causing the problems.<br />
See [[Basic Troubleshooting#Make_a_new_profile|Basic Troubleshooting: Make a new profile]]
If that new profile works then you can transfer some files from the old profile to that new profile (be careful not to copy corrupted files)
See http://kb.mozillazine.org/Transferring_data_to_a_new_profile_-_Firefox

Multicast VPN Extranet Support doesn't work after reload

Hi!
We have Cat6500 with configured Multicast VPN Extranet Support feature. After reload of the 6500 customers in the receive MVPN cannot get mcast stream. We connect test device into source MVPN on that 6500 - everything is OK, mcast stream is available.
Workaround is "no mls ip multicast/mls ip multicast". After these commands mcast in the receive MVPN works fine.
IOS 12.2 SXJ2
Looks like a bug. We have several Cat6500 but only two of them have this issue.
Does anybody faced with such trouble?

Hi!
We have Cat6500 with configured Multicast VPN Extranet Support feature. After reload of the 6500 customers in the receive MVPN cannot get mcast stream. We connect test device into source MVPN on that 6500 - everything is OK, mcast stream is available.
Workaround is "no mls ip multicast/mls ip multicast". After these commands mcast in the receive MVPN works fine.
IOS 12.2 SXJ2
Looks like a bug. We have several Cat6500 but only two of them have this issue.
Does anybody faced with such trouble?

10000: PPPoE session recovery after reload

Hi.
We have seen that there are a feature that recover the PPPoE sessions closed in one side and up in the other. This feature is called 'PPPoE Session Recovery After Reload '.
In the feature navigator, we can see that this feature is available for 7200 series. It seems not available for 10000.
But in the release notes of Cisco IOS 12.3(7)XI3,
http://www.cisco.com/en/US/partner/products/hw/routers/ps133/prod_release_note09186a008040929e.html
appears this bug as resolved:
CSCsa46626
PPP PADT messages are not sent by a PPPoX PTA router to a client when the PPPoX user is no longer connected to the PPPoX PTA router.
This feature is enabled only within the BBA Group configuration using:
bba-group pppoe pppoe1
sessions auto cleanup
This issue can occur when a Cisco 10000 Series router is used as a PPPoX PTA router, and there has been a network flap causing the PPPoX users to lose their connections. PPPoE will experience this issue when BBA Groups are in use. VPDN Group configuration does not support this feature.
There are no known workarounds.
We have tested the IOS 12.3(7)XI6, but the router (10000) doesn't send the PADT (auto cleanup). In 7200, it works correctly.
Anyone have has this problem?
Anyone can confirm if this feature is supported?
Regards.
Jose

Hi Jose ,
I checked it using feature navigator and noticed that cisco 10000 doesn't support ""PPPoE Session Recovery After Reload"" feature.
The following platforms support the feature.
1700
1800
2600
2800
3200
3600
3700
3800
7200
7301
7400
Thanks,
satish

IPhoto will not open even after reload

I have remove iPhoto and reloaded from disc. Still getting the same error message. I am basically pretty frustrated at this point, any ideas?
Interval Since Last Report: 13374 sec
Crashes Since Last Report: 8
Per-App Crashes Since Last Report: 8
Anonymous UUID: 41254D60-DDE4-4A37-A55C-DB4E70D14C3F
Exception Type: EXC_BREAKPOINT (SIGTRAP)
Exception Codes: 0x0000000000000002, 0x0000000000000000
Crashed Thread: 0
Dyld Error Message:
Library not loaded: /System/Library/PrivateFrameworks/iLifeSlideshow.framework/Versions/A/Framework s/iLifeSlideshowProducer.framework/Versions/A/iLifeSlideshowProducer
Referenced from: /System/Library/PrivateFrameworks/iLifeSlideshow.framework/Versions/A/iLifeSlid eshow
Reason: no suitable image found. Did find:
/System/Library/PrivateFrameworks/iLifeSlideshow.framework/Versions/A/Framework s/iLifeSlideshowProducer.framework/Versions/A/iLifeSlideshowProducer:
stat() failed with errno=5=

I am at my wits end with iPhoto error messages and inability to reload it. It has worked fine until yesterday when I started getting the library not loaded error message. I deleted the app, removed the pkg files from HD/Library/Receipts and reloaded the app from my iLife CD as suggested. I have done this 6 times without success and continue to receive the same error message. During reinstall it runs for a long time saying loading packages. After reload there are no new pkg files in teh HD/Library/Receipts location. I do not know what to do next . . . I am open to any assistance.

Anyway to recover photos on a iPhone 4s after reload of os?

Anyway to recover photos on a iPhone 4s after reload of os?

Only from your backup if you have any.

After reloading adobe creative suite cs3 on my mac 10.4.11 acrobat will not open any pdfs it previously opened. help!

after reloading adobe creative suite cs3 on my mac 10.4.11 acrobat will not open any pdfs it previously opened. help!

hello.   hey, thanks very much for writing back. i got some good info with a search or two. (info about what regedit is and what corresponds to it in OS X -- regedit allows you to edit "preference" keys for individual programs, OSX's equivalent for these keys are the .plists in User & System: Preferences and Application Support)
what i ended up doing was uninstalling Premiere Pro (not the suite, just PPro).   Then i deleted a few preference files:
from User /Preferences/Adobe:
com.adobe.AdobePremierePro.plist
com.Adobe.Premiere Pro.5.0.plist
and from System Preferences:
the file: Adobe Premiere Pro Prefs
and..
/.../Premiere Pro/5.0/...
AMEPrefs.xml     (i noticed that there's also a preference file in Media Encoder's own folder so i didn't sweat this one)
Debug Database.txt
Placeholder Preset.epr
PostEncodeCmds.pref
PresetCache.xml
Trace Database.txt
NOTE:
of course i don't know if deleting any files beyond the 2 .plist files in User Prefs was necessary, but... it seems to have worked.
I then reinstalled Premiere Pro CS5, and fired up an old project and i've got playback of HD and DV files, and snappy editing and rendering, so hopefully i'm good to go.   I'm just going to stick with v5.0.0 because i actually don't remember ever having any trouble with it, and i don't remember v5.0.4 adding anything i was 'missing' or 'needed'
hopefully, this thread will be useful for any future folks that run into trouble - and it's got a solution for both Windows and OS X
happy editing,
peace

After reloading a website its page is not active.

After reloading a website the page is not active. I have to click on a different program, minimize and restore, or click on the windows task bar and then things are able to be clicked on and pointer is recognized. All sites are affected
== URL of affected sites ==
http://ALL SITES
== User Agent ==
Mozilla/5.0 (Windows; U; Windows NT 5.1; en-US) AppleWebKit/533.16 (KHTML, like Gecko) Version/5.0 Safari/533.16

Hi ,
According to your description, my understanding is that you got an error when you clicked the link to a library.
Whether you customize the library page.
Please check Recycle Bin on your site, see whether there is the library in it. If yes, restore the library, then compare the result.
If this issue still exists, please find more information about this issue in the logging file, the path is C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\LOGS.
I hope this helps.
Thanks,
Wendy
Wendy Li
TechNet Community Support

CX Module failed after reload

Hi there!
I do know if it is some kind of bug, but all the time after reload the CX module all things stop work, regardless of what form do I reset the module.
I already tried to acccess the module and reload, tried to stop services with "services stop" command and after that "reload", tried to shutdown using ASA commands and reload it from ASA... everytime I reload when the module come back all services start perfectly, like example below:
spcx02>show services status
============================================================
Process           | PID   | Up    | Up Time
============================================================
AD Interface      | 6284 | True | 05:03:03
Message Nameserver| 6022 | True | 05:03:59
HTTP Auth Daemon | 6094 | True | 05:03:58
PDTS              | 6073 | True | 05:03:59
HTTP Inspector    | 6193 | True | 05:03:37
HTTP Server       | 5972 | True | 05:03:59
Data Plane        | 6270 | True | 05:03:06
Management Plane | 6115 | True | 05:03:45
HPM Monitor       | 6289 | True | 05:03:03
Updater           | 6399 | True | 05:02:52
Card Manager      | 5930 | True | 05:03:59
ARP Daemon        | 6089 | True | 05:03:58
Event Server      | 6133 | True | 05:03:41
TLS Proxy         | 6204 | True | 05:03:37
============================================================
spcx02>show ver
Cisco ASA CX Platform 9.1.2 (42)
Cisco Prime Security Manager 9.1.2 (42) for spcx02 firewall
spcx02>
I even can access the GUI using my browser, but all athentication with CDA or AD that before boot was working correctly show up the error:
"Connection failed with error: Could not connect to virtual directory interface."
Everytime I reload I must reinstall the entire module and reconfigure everything. Anyone know if this is a bug that crashes the database or something like this?
Regards,
Rodrigo Alves

Ah, I forgot to write down that after reload the module and it come back it stop all traffic passing through the firewall and I must remove the policy-map configuration:
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect rsh
inspect rtsp
inspect sqlnet
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
inspect h323 h225
inspect h323 ras
inspect skinny
class class-default
cxsc fail-open auth-proxy

Possible fix for OS X 10.5.7, losing connection after sleep, restart

Possible fix for OS X 10.5.7, Airport, losing connection after sleep, restart, or cold reboot.
Issue: (For OS X 10.5.7 on iMac5,1, Intel Core 2 Duo)
=============================================
- After sleep, restart, cold reboot, even though cannot connect to Internet, but the AirPort bars are still full, as if connected.
- Losing Internet connection after sleep, restart, cold reboot.
Possible Fix:
1.Open Network Preference, click on the Location drop down list > Edit Location... > click on the wheel button > Duplicate Location.
a)Select this newly setup location; Use Diagnostic button to connect to the internet. Select Network or enter WEP password if necessary.
b)Test to make sure you can connect to a web page.
c)Go to sleep & wake up.
d)This time, the Airport bar will start to show correctly. Before, it will always be full even when not connected. Now there will be no bars or grey out when not connected.
2.On the left hand side of the Network Preference Window, there is a list of services, such as Airport, build-in ethernet, built-in FireWire, bluetooth, etc.
a)Click on the wheel button on the bottom of the service list; select Set Service Order...; move Airport to the top of the list.
b)Delete any services which you are sure that you are not going to use, such as Bluetooth, etc.
3.Pick one of the locations mentioned in #1, and make it sure it is connected. If not, use Diagnostic button. If you have to select Network or enter WEP password to connect, make it so.
a)Check to make sure you can connect to a web page.
4.Go to sleep & wake up. The Airport bar should be filled up quickly. Try to connect to a web page.
5.Restart computer. Test a web page.
6.Shut down & Start computer. Test a web page.
7.When everything is working fine, you can delete the extra location that you created in step #1.
8.Click the lock on the left lower corner of the Network Preference window to safeguard the setting.

If my assessment is correct, the LIDE 200 driver is version 14.8.1 and dated 26-Sep-2008. It is possible that the driver will not work with the latest version of OSX. I would advise that you contact Canon and ask them the question.
(Removed link because of the way Flash drives the Canon site).
It is not uncommon (though irritating) that devices no longer work when an OS is upgraded. One has to ask the question if (or why) the driver was not written in such a way as to be OS version independent.
Chris
I spoke to Canon over here in Australia. Not helpful at all. In fact they were about as useful as an ashtray on on motorcycle. Having said that the tech seemed to think that there would be an update soon. But that is assuming that Canon are aware that there is a problem with that Scanner under OS X 10.5.7.
Message was edited by: 2point5

How to fix Gridview after reloading Grid in Adobe flex-

hi folks,
i have searched a lot but could not find the exact way to do this... you will understand better if you will look once this page.please open this in IE.
http://www.freescale.com/webapp/search/MainSERP.jsp?SelectedAsset=Orderable%20Parts#breadc rumb_anchor
Here is my scenario goes...
click om power Actuation present in leftnav under Analog & Power Management. you will get result table and above that i have a container which shows different filter criteria. now find a filterable header(match header name with filter header) that is out of the screen fold to the righ,then Choose a value for filter exercise, filter by it.
now here my problem arises
after reloading the results, the table-view comes back to it's starting position, which creates the confusion to end user about the results.
so my question is how can i prevent my table-view to gets back to it's starting point?
i want the scenario which i described above, should work in this way.
Value is chosen for filtering, filtering starts, the reloaded values appear in the same screen position, as before the value was chosen.
i thought about viewStack but could not figure about how to do?
any suggestion or solution will highly appreciated!!!!!
Thanks in advance for your valuable time which you spend to read my question.
Thanks,
Vivek

[discussion moved to Creating, Editing & Exporting PDFs forum]

Catos 7.4. losing config after reload

Similar Messages

Maybe you are looking for