CATOS to IOS commands

Hi,
Just wandering if someone could tell me the IOS equivalent to these CATOS commands. I have been to the CATOS TO IOS Conversion utility Page and to be honest it doesn't work properly and skips a majority of commands.
The CATOS commands l need translated to IOS are :
set trunk 11/8 nonegotiate dot1q 1-1005,1024-4094
clear trunk 11/8 1006-1023
clear trunk 11/6 1-39,41-99,101-339,341-419,421-4094
set trunk 11/6 nonegotiate dot1q 40,100,340,420
clear trunk 11/13 1006-1023
set trunk 11/13 auto-negotiate 1-1005,1024-4094
#IPACLVLAN280
set qos acl ip IPACLVLAN280 dscp 32 ip any any
commit qos acl all
set qos acl map IPACLVLAN280 280
Thanks much appreciated

hi,
the three trunk command-blocks should be converted in this way:
clear trunk 11/8 1006-1023
set trunk 11/8 nonegotiate dot1q 1-1005,1024-4094
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-1005,1024-4094
switchport mode trunk
clear trunk 11/6 1-39,41-99,101-339,341-419,421-4094
set trunk 11/6 nonegotiate dot1q 40,100,340,420
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 40,100,340,420
switchport mode trunk
clear trunk 11/13 1006-1023
set trunk 11/13 auto-negotiate 1-1005,1024-4094
switchport trunk encapsulation negotiate
switchport trunk allowed vlan 1-1005,1024-4094
switchport mode dynamic auto
kind regards,
Bernhard

Similar Messages

Convert Qos commands from CATOS to IOS

Hello,
i've some problems converting some Qos commands from CATos to IOS can anybody help me?
set qos drop-threshold 1q4t rx queue 1 50 60 80 100
set qos map 2q2t tx 1 1 cos 0
set qos map 1p1q4t rx 1 3 cos 4
set qos wrr 1p2q2t 50 255
set qos txq-ratio 1p2q2t 70 15 15
set qos wred 1p2q2t tx queue 1 70:100 70:100
set qos bridged-microflow-policing disable 1,50-54,100-121,500,700-702,1006-1011,1016
set qos policed-dscp-map 1:1
set qos policed-dscp-map excess-rate 0:0
set qos acl default-action ip dscp 0
set qos acl default-action ipx
set qos acl default-action mac
set qos policy-source local
set qos rsvp disable
set qos rsvp policy-timeout 30
set qos rsvp local-policy forward
!Module with GE interfaces
set port qos 3/1-16 cos 0
set port qos 3/1-16 trust trust-cos
set port qos 3/1-16 port-based
set port qos 3/1-16 policy-source local
set qos statistics export port 3/1 disable
set qos statistics export port 3/2 disable
set qos statistics export port 3/3 disable
set qos statistics export port 3/4 disable
set qos statistics export port 3/5 disable
set qos statistics export port 3/6 disable
set qos statistics export port 3/7 disable
set qos statistics export port 3/8 disable
set qos statistics export port 3/9 disable
set qos statistics export port 3/10 disable
set qos statistics export port 3/11 disable
set qos statistics export port 3/12 disable
set qos statistics export port 3/13 disable
set qos statistics export port 3/14 disable
set qos statistics export port 3/15 disable
set qos statistics export port 3/16 disable

This URL should help you:
http://www.cisco.com/warp/public/473/73.html

6509 conversion from CatOS to IOS

I am interested in hearing from those who have converted from CatOS to IOS using 6500 as primarily a LAN switch with InterVLAN routing. Are there valid reasons / advantages to running IOS over CatOS? It seems to me that the CatOS is more efficient language for configuring switch ports and the IOS is better for configuring routing. I use 6509 in the core for server farms mostly and with the integration of many IOS based switches (3750) I am considering migrating the 6509 to IOS as well.
Thanks,
Greg

Greg,
Cisco may support CATOS for a while, but I do think that they may end of life it in the future. Thats why there is a big push on the IOS over CATOS.
I feel that the IOS is equally efficient in configuring switch ports as CATOS. You can use interface range commands to configure common parameters to a range of switch ports. And the great thing about configuring switchports in IOS is that it will have the same syntax like your 3750 switches.
Here is a link that compares commands on both switches which will help a lot after migration.
http://www.cisco.com/en/US/products/hw/switches/ps700/products_tech_note09186a008010e9d5.shtml
Sankar
PS: please rate helpful posts!

Catalyst 6509 Conversion from CatOS to IOS.

Hi,
I am converting a Cat6509 Sup720 CatOS to IOS.The switch also has a FWSM configured. During converting CatOS to IOS will the FWSM configuration be erased or affected by any means ?
Regards
Kas

there should be no affect or deletion/problems with the FWSM during your IOS conversion.
haven't seen any issues in my LAB. the conversion process has a part where the CatOS commands/config are converted to the IOS commands/config required.
you should make sure you backup the FWSM configuration and partitions before you begin.
please see the following link for the CatOS to IOS conversion tasks for the sup720:
http://www.cisco.com/en/US/products/hw/switches/ps708/products_tech_note09186a008015bfa6.shtml#conv_720

Aironet 1242 IOS Commands

I am trying to set airnoet 1242 access point model #AIR-LAP1242AG-A-K9 and I am using the guide found at
http://www.cisco.com/en/US/docs/wireless/access_point/12.3_7_JA/configuration/guide/s37frst.html
The IOS version is 12.3(11)JX1 but when I try any of the standard IOS commands(configure terminal is not a valid command) I get an "unreconized command" error I also can not access the web GUI. I have set the ip and can ping it but when I browse to it I get nothing.
I would be greatful for any help.

Hi,
If you follow Robs document, you need to download the IOS softeare and rename the filename to " c1240-k9w7-tar.default " as this is the filename the AP seaches for during boot up.
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
If you follow the steps i mentioned, you do not need to rename the file.
To get the IOS images you can go to the download software section on www.cisco.com.
The latest IOS release for 1240 APs is "c1240-k9w7-tar.124-21a.JY.tar".
HTH,
Tiago
If this helps you and/or answers your question please mark the question as "answered" and/or rate it, so other users can easily find it.

"Restart Now" IOS command for 1310 Wireless Bridge

I have 2 Cisco Aironet 1310 wireless bridges setup, line-of-sight, 3/4 mile apart, one as Root, the other as Non-Root. Occasionally they drop their connection but a hard restart of either or both bridges will reestablish the connection. What is the equivalent IOS command to the
"GUI > System Software > System Configuration > Restart Now" command? I would like to be able to telnet to either/both units and issue/script the appropriate command.

the command is "reload"
BRIDGE# reload
Regards
Surendra

ACS 5 and IOS command issued records

on ACS Ver5.2.0.26.11, where can i find the records of IOS command issued from a router?
thanks,
Han

Well, it depends.
If you're sending accounting messages for commands from your router, it would either be in the report with Radius Accounting or TACACS+ Accounting.
If you're performing command authorization it would be in the report for TACACS+ Authorization.
If you provide a 'show run | inc aaa' it should be enough detail to determine what report you need to look at.

Which IOS command allows me to check AP's current working mode?

Hi All,
I would like to know that my AP is working in root mode or workgroup bridge mode. I can check it via web browser. Just curious how to check it via IOS command. Thanks in advance.

Hi Robert,
Perform the "show run interface dot0" command to show the running-configuration for your dot11radio0 interface. Look for the command line that starts with "station-role". This will tell you what role your radio is in.
For example, if it is "station-role root bridge", the radio is configured as a root bridge. If it's just "station-role root", then it's configured as an infrastructure AP.
This is what Rob is saying, but a bit more specific. I don't know of there being a "show" command that states what the radio's role is.
Jeff

CatOS to IOS conversion without RP

We have a Cat 6509 with a WS-SUP32-GE-3B and want to convert the CatOS to IOS. We need to know if we can do the conversion, since we don't have a Route Processor implemented on the switch infrastructure. This environment consists of pure layer 2 switches with stand alone switch processors and no routing capabilities. Everything we've read shows navigating into the RP to load the new image. Would we be capable of converting to IOS in this instance?
Thanks for any help..

I am not at the remote site, but this is the show module for the CAT 6509:
Here's the list of modules within the chassis:
Mod Slot Ports Module-Type Model Sub Status
1 1 48 10/100/1000BaseT Ethernet WS-X6148A-GE-TX no ok
2 2 48 10/100/1000BaseT Ethernet WS-X6148A-GE-TX no ok
3 3 48 10/100/1000BaseT Ethernet WS-X6148A-GE-TX no ok
4 4 48 10/100/1000BaseT Ethernet WS-X6148A-GE-TX no ok
5 5 9 1000BaseX Supervisor WS-SUP32-GE-3B yes ok
6 6 48 10/100/1000BaseT Ethernet WS-X6148A-GE-TX no ok

CatOS to IOS Converter tool

Hi,
Does anybody have any experience of using the CatOS to IOS Converter tool on a Sup720?
Just to be clear, I'm not referring to the Configuration conversion tool but to the actual OS conversion tool. The CCO document (http://www.cisco.com/en/US/products/hw/switches/ps708/products_tech_note09186a008070f124.shtml)
indicates the tool was tested on a Sup2 only but i was wondering if it could be used with the Sup720's as well?
If not i assume everyone would suggest the manual method as the preferred method of converting from Hybrid to Native?
Thanks

Cisco Software Config. Tools for Cat6000:
http://www.cisco.com/cgi-bin/tablebuild.pl/cat6000-config-converter

Catalyst 5505 conversion from CatOS to IOS

I want to know if somebody has the CatOS to IOS conversion procedure for a Catalyst 5505.
Thank´s a lot
Jorge

The Cat 5000s always run only CATOS. Only the L3 module supports IOS.Only the sup engines on the6500 and7600 support theconversion from CATOS toIOS.

Sup32 from CATOS to IOS

I am about to begin a conversion from CATOS to IOS. I was wondering if I could do the following:
1: Use a new flash card, and format it in an NATIVE IOS Sup720
2: Put the correct code and configuration on it
3: Put it in the Sup32 and rebooted it
Would this then allow the Sup32 to boot up using IOS and not CATOS. I know I may have to copy the configuration from the flash to NVRAM but it seems like the quickest process, instead of the 30 minutes based on CCO documentation.
Thanks

I actually just tried this and it workerd. I took a sup32 that was running CATOS. Put in a CF card that was formated in a SUP720 with the IOS image on it. Replaced the on-board CF card with the new one. The system booted and couldn't find and files. I put the boot variable in ROMMON mode and bam up and running. Just had to change the bootvar in IOS and create the new config. Much faster than doing two copies of a 76MB file.

CatOS versus IOS

Hi all.
Can any body please explain to me what is the difference between CatOS and IOS.

Hi Friend,
CatOS on the Supervisor Engine and Cisco IOS Software on the MSFC (Hybrid): A CatOS image can be used as the system software to run the Supervisor Engine on Catalyst 6500/6000 switches. If the optional MSFC is installed, a separate Cisco IOS Software image is used to run the MSFC.
Cisco IOS Software on both the Supervisor Engine and MSFC (Native): A single Cisco IOS Software image can be used as the system software to run both the Supervisor Engine and MSFC on Catalyst 6500/6000 switches.
http://www.cisco.com/en/US/products/hw/switches/ps700/products_tech_note09186a008010e9d5.shtml#Diff
HTH, if yes please rate the post.
Ankur

What IOS command similar to catos command 'set port vtp X disable'

Hi,
Does anyone know if a similar command of catos command 'set port vtp X disable' exists in native IOS (12.1E or 12.2SX) on cat6500?
We still can play in native IOS with VTP pruning, transparent mode but it seems that we can no more disable VTP on a particular port/interface.
Many thanks.
Regards/Ludovic.

While one may not be able to disable VTP directly, I would think you could use a MAC ACL against the VTP MAC address of 01-00-0C-CC-CC-CC. (See http://www.cisco.com/en/US/partner/tech/tk389/tk689/technologies_tech_note09186a0080094c52.shtml for details on how that addressing works.)
See http://www.cisco.com/en/US/partner/products/hw/switches/ps708/products_configuration_guide_chapter09186a00801679f8.html#wp1359352 for details on the command syntax.
Hope this helps. Please rate helpful posts.

CatOS to IOS conversion

I would like to convert CatOS configuration file to IOS
I am trying to use the Configuration Conversion Tool on Cisco web
CatOS has two configuration file ( SUP Configuration & MSFC configuration )
Which file should I paste on the Conversion tool to be converted ?
Some commands can't be converted (Skipped Commands) ?
Any one has experince with the Cat configuration conversion tool can help me ?
Regards
Mohamed

Hi Mohamed,
The MSFC configuration you will not need to translate. This configuration is always in IOS mode and it will be the same in the native mode.
I have some translation to your CatOS commands:
set password xxxxxxxxx
set enablepass xxxxxxxxx
You will not need because you will use the password from your MSFC configuration.
set prompt tower_main --> hostname touwer_main
set system highavailability enable
set inlinepower defaultallocation 7000
These 2 commands I don't remember.
set spantree mode pvst+
This command you will not need because this is the default mode of spantree.
set vtp passwd portfast --> vtp passwd porfast
set vtp version 2 --> vtp version 2
set ip alias default 0.0.0.0
set logging server enable
set timezone PDT -7 0
set boot config-register 0x2102
These commands above you won't need because they must already exist in your MSFC configuration.
set boot system flash bootflash:cat6000-sup2k8.8-2-1.bin
Your will replace this with the new IOS image in the native mode, and the syntax is the same that in youe MSFC configuration:
boot system flash bootflash:image.bin
set igmp querier enable 1,500,700
set port dot1x 1/1 guest-vlan 0
set port qos 3/4,3/9,3/11 trust trust-cos
set port qos 3/1-4,3/9-12 policy-source local
set port qos 4/11 trust trust-cos
set port qos 4/9-12 policy-source local
These other commands above I don't remember.
set span 1 10/13 both inpkts disable learning enable multicast enable create
In the native mode you will replace the "set span" with the command "monitor session". Here is an example:
monitor session 1 source interface fastEthernet 0/1 both
monitor session 1 destination interface fastEthernet 0/9
It will monitor fast0/1 and will send all the traffic to interface fast0/9
I hope that this can help you.
Fabrício Nunes Monte
Network Analyst

CATOS to IOS commands

Similar Messages

Maybe you are looking for