CCM intergrate with CME!!!

CMM 4.13sr3c and CME3.3
I am not using hardware gatekeeper at all.
At CCM, I created Trunk(not gatekeeper controlled), and route group, list and pattern. I can make a call to CME's phone without any problem.
At CME:
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g729r8
voice class h323 1
h225 timeout tcp establish 3
dial-peer voice 1000 voip
destination-pattern [12]...
voice-class codec 1
voice-class h323 1
session target ipv4:10.0.0.21 (Sub)
dtmf-relay h245-alphanumeric
dial-peer voice 1001 voip
preference 1
destination-pattern [12]...
voice-class codec 1
voice-class h323 1
session target ipv4:10.0.0.20 (Pub)
dtmf-relay h245-alphanumeric
I could not call from CME to CCM, I got fast busy.
Thanks for help.
Ken

I would check if the phones in CCM you are calling is in a partition, then the Trunk in CM should have a Inbound call CSS set with access to that partition.
HTH
Sankar.
PS: please remember to rate posts!

Similar Messages

Registering SPA500 series IP phone with CME 8.6

Hello friends. I'm newbie with CME configuration, but now I'm asked to register SPA504G phones onto a CME 8.6 installed on a Cisco 2911 router using SIP protocol. I'm testing with a SPA 502G phone with software version 7.4.7. Within "voice register global" configuration I can't find "load" command for thisphoone model. About phone files, I only found "spa50x-30x-7-4-8a.bin" file for this phone and loaded into flash: unit.
How can I make SPA 500G phone be registered with this CME? I would appreciate somebody can help me with a guide to achieve this.
Thanks in advance for your help.
Best regards
Joe

I have the same problem.
Can anyone help?
Thank you.

Cisco ip phone 9971 registration failed with CME 8.6 on WAN

Dear Sir
Subject: Cisco ip
phone 9971 registration failed
with CME 8.6 on WAN
I have a WAN simulation with one Cisco2811 router one Cisco1841 router (connected with fast Ethernet interface) plus one layer 2 switch.
I upgraded the 2811 IOS to 15.4M and installed CME8.6, when we tried to add 9971 sip phone If the traffic goes throw LAN (Same subnet- directly from switch to 2811) everything is fine and the SIP phone (9971) added with no problem but when I change the subnet and traffic goes throw WAN
( from 1841 routed to 2811 with default route) my phone didn't register.
It will be great if anybody could help!!
If you can solve my problem, I will be happy to compensate.

Try binding SIP to an interface on which Phone can reach (Use "voice service voip" "sip" and then bind)
Udit

What types of third party loyalty solution can SAP POS 9.5 intergrate with

What types of third party loyalty solution can SAP POS 9.5 intergrate with (reserached already Rediron, and DBS)?
Looking For Loyalty\rewards and giftcard solution. Any advice would be appreciated.

Hi Hiram,
The SAP POS Suite has solutions already in place for Loyalty - Allegiance Analytics and for Gift Card - SVA. However, there are other 3rd party options that can be incorporated into the POS as well, but you would need to contact those vendors directly.
Regards,
Mark

7921 not registering with CME through repeater

I have this environment:
CME 7.0 running in Cisco2851.
WLC2106 with 6 1242 APs
15 phones 7921
I have to extend the wireless coverage to an specific point (warehouse), 150 meters away. This point only have a PC and a phone, so I don't think a bridge is necessary. I have an 1131 AP configured as repeater. In my tests (locally) I see the 1131 is registering to the main wireless network. Using site survey feature in the 7921 I see the SSID broadcast from the repeater AP, but if I use Neighbor list feature the network is not allocated and obviously the phone can't register with CME. Only for tests I had disabled all security features for this SSID.
The 1131 association table only shows the root AP but it indicates the IP address assigned to the controller.
Can somebody give me some tips to identify what I'm missing?
Thanks in advance

I think H-REAP is a feature not usable for this case, isn't
I'm reading the "Cisco Wireless LAN Controller Configuration Guide", in page 7-19 and follow, Workgrouup Bridge is explained. I think it should be the solution for my requirements, although I will test tomorrow (Wendesday), I have some questions:
The example shows a hub in remote site, I guess it can be replaced with a switch without any problem.
Could it be possible to set another AP attached to the switch to get wireless access? Otherwise, I will need a desktop phone.
The manual indicates NO VLAN are supported (page 7-21), so this option will need PC and phone for this site running in the same VLAN?
I appreciate your assistance.
Daniel Escalante.

Where can I find what phone loads are compatible with CME?

I recently upgraded one of our CME systems to CME v10.0
I noticed that even though the CMEv10 Supported Firmware page says the compatible phone load for my 7911 phones is 9-2-1TH1-13,
my 7911's running phone load 8-4-3-16 all seem to be registering and running just fine.
So I must conclude that 7911 phone load 8-4-3-16 is compatible with CME v10.0
Where can I go to find out what phone load versions are compatible with CME or perhaps, at least, where I can find what phone loads are no longer supported by a version of CME?

Hi Jared,
Specific CME versions are tested with the versions listed on the "requirements" doc like the one you mentioned (linked below), but are not limited to those firmware versions. The phone loads/firmware is completely independent from the CME/IOS version. And it is often appropriate to upgrade or downgrade phone firmware levels on CME and is fully supported :)
http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/requirements/guide/cme10spc.html
I would look at upgrading the 8-4-3 firmware for the 7911's BUT you will need to move to an interim mid-point release like 8-5-2 as a first step due to the "important notes" shown here;
Firmware Upgrade Issues for SCCP
Note For all SCCP firmware upgrades from firmware release versions earlier than 8.3(3) to version 8.5(3) or greater, you must first upgrade your firmware to version 8.5(2). Once you have upgraded to version 8.5(2), you can upgrade your IP Phone to version 8.5(3) or later.
http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/firmware/8_5_3/english/release/notes/7900_853.html#wp57602
Cheers!
Rob

Need help on displaying the callers name on ip phone with cme using external directory

Hello Guys,
Need help on displaying the callers name on ip phone with cme while using external directory
Thank you,
Khaja

Thanks for your help,
Does it 100% work with CME. We use SIP and 2ring for external directory? Thanks you.

Help with CME UF transport in Logic!

Can anybody help with CME UF transport keys in Logic? How to make them work?

I don't know if any of this applies to your specific situation, but here are some things I've noticed.
*Mono Audio Channel Strip:*
If you click on an empty send slot and select a buss, a mono Aux Channel Strip is created. Even if you open a Mono->Stereo version of a reverb plug-in on the mono Aux Channel Strip, the sound of the reverb will still be mono. *(Even if you turn the mono Aux Channel Strip into a stereo Aux Channel Strip _after the fact_.)*
To get the desired Post Pan behavior, you would need to change the mono Aux Channel Strip to Stereo before you open the reverb plug-in. (In this case, since the Aux is now stereo, the only choice for the reverb plug-in will be Stereo.)
*Stereo Audio Channel Strip:*
If you click on an empty send slot and select a buss, a stereo Aux Channel Strip is created. The only choice for the reverb plug-in will be Stereo. The sound of the reverb will be Stereo.
If you wanted to have "Post Pan" reverb for a Stereo Audio Channel Strip, you should use the Direction Mixer for the panning because the Pan knob on Stereo Channel Strips is a Balance control. (Not true pan)
*Also of note:*
You can also create Aux Channel Strips by clicking on the + button at the left of the Mixer Window. The first time you click it, the dialog that opens defaults to Mono. If you change it to Stereo, it will default to Stereo until you change it again.
With all that said, my questions to you:
1. Is the Channel Strip with the Post Pan sends a mono Channel Strip?
2. How did you create the Aux Channel Strip for the reverb?
3. Is the Aux Channel Strip with the reverb a stereo Aux Channel Strip?

CCMS-functinality with Solution Manager 4.0

Hello,
I am seeking for the documentation regarding the setup and use the CCMS-functionality with Solution Manager 4.0
Is there some documents describing this feature in details?
Thank you!
regards
Axel

Hi,
Check <a href="https://websmp108.sap-ag.de/sapidb/011000358700005479192006E.sim">this.</a> and <a href="https://websmp108.sap-ag.de/sapidb/011000358700006936062005E.sim">this</a>.
This will solve your problem.
Feel free to revert back.
--Ragu
Message was edited by:
Raguraman C

Blackberry registeration with CME

hi all,
I want to know whether one can install the client on blackberry phone same as nokia e71 and register the blackberry phone with cme via wifi. Can somebody provide the link for the documentation
Regards
Nareh

It seems BlackBerry launched complete product - the BlackBerry® Mobile Voice System that can be integrated with CME:
http://na.blackberry.com/eng/services/business/blackberry_mvs/
Here is Configuration Guide:
http://docs.blackberry.com/en/admin/deliverables/20062/BlackBerry_Mobile_Voice_System-Configuration_Guide--1079341-0901073810-001-5.0.1-US.pdf
What I have noticed from document is that "the BlackBerry® Mobile Voice System integrates your organization's PBX phone system with the BlackBerry® Enterprise Server to extend desk phone features to BlackBerry devices". In other words you will need BlackBerry® Enterprise Server working as well for the system to function.
So I guess to install all it if you have only couple of BlackBerry phones is senseless.
I'm curious if it would be possible to use without BlackBerry® Enterprise Server having just simple client on the phone like Nokia Call Connect, for instance with Nokia E-series phones.

Will CUE Unity Express 8.6.7 integrate & work with CME 10.0 & 10.5

Hi,
Will CUE Unity Express 8.6.7 integrate & work with CME 10.0 & 10.5
As i am having currently CUE 8.6.7 and wanted to upgrade my CME 9 to 10.0 or 10.5.
Thanks.

Hi there,
You would require CUE 8.6.9 or 8.6.10 as shown below;
Table 1: Cisco Unity Express: Unified CM Express and Unified SRST Versions
Cisco Unity Express Versions
2.0.x
2.1.x
2.2.x
2.3.x
3.2.x
7.0.x
7.1.x
7.2, 8.0
7.3, 7.4, 8.5, 8.6
8.6.7
8.6.9
8.6.10
3.1.x
Cisco Unified Communications Manager Express
Versions
and
Cisco Unified Survivable Remote Site Telephony Versions
3.0,
3.1
3.2,
3.2(1)
3.2(2)
3.3,
3.4
4.0
4.0(1), 4.0(2),
4.0(3)
4.1,
4.2
4.3/7.0
7.1
8.0
8.1
8.5, 8.6, 8.8, 9.x
10.0, 10.5
Before version 4.1, Cisco Unified Communications Manager Express was known as Cisco Unified CallManager Express.
From;
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/unity_exp/compatibility/cuecomp.html
Cheers!
Rob

Integation of Unity Express with CME

When i integate unity express with CME,on the unity express Admin page when configuring CME
what is
1.hostname
2.Web User Name
3.Password.
should I enter these parameters to integate?
thanks
kavi

Following are the commands I used on CME for the integration
interface Integrated-Service-Engine0/0
ip unnumbered Loopback1
service-module ip address 10.1.9.1 255.255.255.252
service-module ip default-gateway 10.1.9.2
ip route 10.1.9.1 255.255.255.255 Integrated-Service-Engine0/0
interface Loopback1
ip address 10.1.9.2 255.255.255.252
telephony-service
srst mode auto-provision all
srst ephone template 1
srst dn template 1
srst dn line-mode octo
max-ephones 10
max-dn 10
ip source-address 10.1.4.1 port 2000
system message CME1861E
voicemail 2000
max-conferences 4 gain -6
web admin system name cisco password cisco
transfer-system full-consult
create cnf-files version-stamp 7960 Jan 02 2013 17:50:08
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
dial-peer voice 300 voip
destination-pattern 2000
b2bua
session protocol sipv2
session target ipv4:10.1.9.1
dtmf-relay rtp-nte
Following are the commands used on unity express
ccn application voicemail aa
description "voicemail"
enabled
maxsessions 6
script "voicebrowser.aef"
parameter "uri" "http://localhost/voicemail/vxmlscripts/login.vxml"
parameter "logoutUri" "http://localhost/voicemail/vxmlscripts/mbxLogout.jsp"
end application
ccn trigger sip phonenumber 2000
application "voicemail"
enabled
locale "en_US"
maxsessions 6
end trigger
When Pressing the message button on the phone,its not routing to voicemail.instead there is a reorder tone.what could be the issu?

Does Cisco CP-8831 work with CME

Hello
Does Cisco CP-8831 phone work with the Call Manager Express
Thanks
Mohamed

As of now no.
http://www.cisco.com/en/US/prod/collateral/voicesw/ps6788/phones/ps12965/data_sheet_c78-726887.html
"Supported on Cisco Unified Communications Manager and Business Edition systems"
There is a defect open that the 8831 datasheet is incorrect with CME 10.0 support for the 8831 (https://tools.cisco.com/bugsearch/bug/CSCui95307/).

UCCE for CCM failover with DNS SRV.

we are testing UCCE for CCM failover with Local DNS SRV. We have enabled the "Use DNS SRV type query:YES"&"Resolve SRV records locally:1" on CVP Call server configuration SIP tab.
The srv.xml file updated with CCM IP addrs in this path \Cisco\CVP\conf\srv.xml
On testing, the agent state moved to reserved state, but call is not delivered. Static Route is added for Phone Extension as "500>,proxy.ipcc.com".
What will be the issue? Kindly let me know what needs to be done.
Thanks & Regards
JP.

So, as Markus already figured out, you need to make sure that your CUCM actually understands that it is the intended recipient for these SIP INVITEs. I.e. if you define the static route to point to cucm.cisco.com you have to specificy the specify the Custer FQDN to be cucm.cisco.com under the 'Cluster Wide Domain Settings' in the CUCM Enterprise Parameters.
A second thing to watch out for the CUCM Group assigned to your SIP Trunks. Each SIP Trunk, like any CUCM device, has a Device Pool, the device pool has a UCM Group defining on which UCM nodes that device 'exists'. For phones that typically means : which UCM nodes can I register to ?
But for SIP trunks this means : which UCM nodes have a SIP deamon process for this Trunk and so which of the UCM nodes will actually accept INVITEs for this trunk. The most common cause for 503 Service Unavailable is probably this, (not all) the CUCM nodes in your DNS / srv.xml round robin are in the UCM Group assigned to the Device Pool configured on the SIP trunk for this Call Server.
Cheers,
Kris

Really Need Some Help with CME 8.6 using IOS as Firewall and Anyconnect VPN on Phones

Hello,
I have a 2911 Router with IOS Security and Voice enabled and we are using CME 8.6. I am using a built-in Anyconnect VPN on 3 phones that are for remote users and thus I needed to enable security zones on the router which works because the remote phones will boot up, get their phone configs and I am able to call those remote phones from an outside line.
The issue I am having is that when I try to dial a remote phone connected via the VPN through port g0/0 from and internal office phone, i.e., NOT involving the PSTN then there is no audio. It's as if no audio is going back and forth. When I take off the security zones from the virtual-template interface and the g0/0 interface then the audio works great and I can reach the phone from internal as I am supposed to.
Could someone take a peek at my security config and see why audio would not be traveling through the VPN when I have my security zones turned on?
clock timezone PST -8 0
clock summer-time PST recurring
network-clock-participate wic 0
network-clock-select 1 T1 0/0/0
no ipv6 cef
ip source-route
ip cef
ip dhcp excluded-address 192.168.8.1 192.168.8.19
ip dhcp pool owhvoip
network 192.168.8.0 255.255.248.0
default-router 192.168.8.1
option 150 ip 192.168.8.1
lease 30
multilink bundle-name authenticated
isdn switch-type primary-ni
crypto pki server cme_root
database level complete
grant auto
lifetime certificate 7305
lifetime ca-certificate 7305
crypto pki token default removal timeout 0
crypto pki trustpoint cme_root
enrollment url http://192.168.8.1:80
revocation-check none
rsakeypair cme_root
crypto pki trustpoint cme_cert
enrollment url http://192.168.8.1:80
revocation-check none
crypto pki trustpoint TP-self-signed-2736782807
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2736782807
revocation-check none
rsakeypair TP-self-signed-2736782807
voice-card 0
dspfarm
dsp services dspfarm
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
vpn-group 1
vpn-gateway 1 https://66.111.111.111/SSLVPNphone
vpn-trustpoint 1 trustpoint cme_cert leaf
vpn-profile 1
host-id-check disable
voice class codec 1
codec preference 1 g711ulaw
voice class custom-cptone jointone
dualtone conference
frequency 600 900
cadence 300 150 300 100 300 50
voice class custom-cptone leavetone
dualtone conference
frequency 400 800
cadence 400 50 200 50 200 50
voice translation-rule 1
rule 1 /9400/ /502/
rule 2 /9405/ /215/
rule 3 /9410/ /500/
voice translation-rule 2
rule 1 /.*/ /541999999/
voice translation-rule 100
rule 1 /^9/ // type any unknown plan any isdn
voice translation-profile Inbound_Calls_To_CUE
translate called 1
voice translation-profile InternationalType
translate called 100
voice translation-profile Local-CLID
translate calling 2
license udi pid CISCO2911/K9 sn FTX1641AHX3
hw-module pvdm 0/0
hw-module pvdm 0/1
hw-module sm 1
username routeradmin password 7 091649040910450B41
username cmeadmin privilege 15 password 7 03104803040E375F5E4D5D51
redundancy
controller T1 0/0/0
cablelength long 0db
pri-group timeslots 1-12,24
class-map type inspect match-any sslvpn
match protocol tcp
match protocol udp
match protocol icmp
class-map type inspect match-all router-access
match access-group name router-access
policy-map type inspect firewall-policy
class type inspect sslvpn
inspect
class class-default
drop
policy-map type inspect outside-to-router-policy
class type inspect router-access
inspect
class class-default
drop
zone security trusted
zone security internet
zone-pair security trusted-to-internet source trusted destination internet
service-policy type inspect firewall-policy
zone-pair security untrusted-to-trusted source internet destination trusted
service-policy type inspect outside-to-router-policy
interface Loopback0
ip address 192.168.17.1 255.255.248.0
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description Internet
ip address dhcp
no ip redirects
no ip proxy-arp
zone-member security internet
duplex auto
speed auto
interface GigabitEthernet0/1
ip address 192.168.8.1 255.255.248.0
duplex auto
speed auto
interface GigabitEthernet0/2
no ip address
shutdown
duplex auto
speed auto
interface Serial0/0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
no cdp enable
interface Integrated-Service-Engine1/0
ip unnumbered Loopback0
service-module ip address 192.168.17.2 255.255.248.0
!Application: CUE Running on NME
service-module ip default-gateway 192.168.17.1
no keepalive
interface Virtual-Template1
ip unnumbered GigabitEthernet0/0
zone-member security trusted
ip local pool SSLVPNPhone_pool 192.168.9.1 192.168.9.5
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
ip http path flash:/cme-gui-8.6.0
ip route 192.168.17.2 255.255.255.255 Integrated-Service-Engine1/0
ip access-list extended router-access
permit tcp any host 66.111.111.111 eq 443
tftp-server flash:apps31.9-3-1ES26.sbn
control-plane
voice-port 0/0/0:23
voice-port 0/3/0
voice-port 0/3/1
mgcp profile default
sccp local GigabitEthernet0/1
sccp ccm 192.168.8.1 identifier 1 priority 1 version 7.0
sccp
sccp ccm group 1
bind interface GigabitEthernet0/1
associate ccm 1 priority 1
associate profile 1 register CME-CONF
dspfarm profile 1 conference
codec g729br8
codec g729r8
codec g729abr8
codec g729ar8
codec g711alaw
codec g711ulaw
maximum sessions 4
associate application SCCP
dial-peer voice 500 voip
destination-pattern 5..
session protocol sipv2
session target ipv4:192.168.17.2
dtmf-relay sip-notify
codec g711ulaw
no vad
dial-peer voice 10 pots
description Incoming Calls To AA
translation-profile incoming Inbound_Calls_To_CUE
incoming called-number .
port 0/0/0:23
dial-peer voice 20 pots
description local 10 digit dialing
translation-profile outgoing Local-CLID
destination-pattern 9[2-9].........
incoming called-number .
port 0/0/0:23
forward-digits 10
dial-peer voice 30 pots
description long distance dialing
translation-profile outgoing Local-CLID
destination-pattern 91..........
incoming called-number .
port 0/0/0:23
forward-digits 11
dial-peer voice 40 pots
description 911
destination-pattern 911
port 0/0/0:23
forward-digits all
dial-peer voice 45 pots
description 9911
destination-pattern 9911
port 0/0/0:23
forward-digits 3
dial-peer voice 50 pots
description international dialing
translation-profile outgoing InternationalType
destination-pattern 9T
incoming called-number .
port 0/0/0:23
dial-peer voice 650 pots
huntstop
destination-pattern 650
fax rate disable
port 0/3/0
gatekeeper
shutdown
telephony-service
protocol mode ipv4
sdspfarm units 5
sdspfarm tag 1 CME-CONF
conference hardware
moh-file-buffer 90
no auto-reg-ephone
authentication credential cmeadmin tshbavsp$$4
max-ephones 50
max-dn 200
ip source-address 192.168.8.1 port 2000
service dnis dir-lookup
timeouts transfer-recall 30
system message Oregon's Wild Harvest
url services http://192.168.17.2/voiceview/common/login.do
url authentication http://192.168.8.1/CCMCIP/authenticate.asp
cnf-file location flash:
cnf-file perphone
load 7931 SCCP31.9-3-1SR4-1S.loads
load 7936 cmterm_7936.3-3-21-0.bin
load 7942 SCCP42.9-3-1SR4-1S.loads
load 7962 SCCP42.9-4-2-1S.loads
time-zone 5
time-format 24
voicemail 500
max-conferences 8 gain -6
call-park system application
call-forward pattern .T
moh moh.wav
web admin system name cmeadmin secret 5 $1$60ro$u.0r/cno/OD2JmtvPq4w9.
dn-webedit
transfer-digit-collect orig-call
transfer-system full-consult
transfer-pattern .T
fac standard
create cnf-files version-stamp Jan 01 2002 00:00:00
ephone-template 1
softkeys connected Hold Park Confrn Trnsfer Endcall ConfList TrnsfVM
button-layout 7931 2
ephone-template 2
softkeys idle Dnd Gpickup Pickup Mobility
softkeys connected Hold Park Confrn Mobility Trnsfer TrnsfVM
button-layout 7931 2
ephone-dn 1 dual-line
number 200
label Lisa
name Lisa Ziomkowsky
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 2 dual-line
number 201
label Dylan
name Dylan Elmer
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 3 dual-line
number 202
label Kimberly
name Kimberly Krueger
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 4 dual-line
number 203
label Randy
name Randy Buresh
mobility
snr calling-number local
snr 915035042317 delay 5 timeout 15 cfwd-noan 500
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 5 dual-line
number 204
label Mark
name Mark McBride
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 6 dual-line
number 205
label Susan
name Susan Sundin
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 7 dual-line
number 206
label Rebecca
name Rebecca Vaught
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 8 dual-line
number 207
label Ronnda
name Ronnda Daniels
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 9 dual-line
number 208
label Matthew
name Matthew Creswell
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 10 dual-line
number 209
label Nate
name Nate Couture
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 11 dual-line
number 210
label Sarah
name Sarah Smith
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 12 dual-line
number 211
label Janis
name Janis McFerren
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 13 dual-line
number 212
label Val
name Val McBride
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 14 dual-line
number 213
label Shorty
name Arlene Haugen
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 15 dual-line
number 214
label Ruta
name Ruta Wells
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 16 dual-line
number 215
label 5415489405
name OWH Sales
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 17 dual-line
number 216
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 18 dual-line
number 217
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 19 dual-line
number 218
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 20 dual-line
number 219
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 21 dual-line
number 220
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 22 dual-line
number 221
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 23 dual-line
number 222
label Pam
name Pam Buresh
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 24 dual-line
number 223
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 25 dual-line
number 224
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 26 dual-line
number 225
label Elaine
name Elaine Mahan
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 27 octo-line
number 250
label Shipping
name Shipping
ephone-dn 28 dual-line
number 251
label Eli
name Eli Nourse
call-forward busy 500
call-forward noan 500 timeout 10
ephone-dn 29 dual-line
number 252
ephone-dn 30 dual-line
number 253
ephone-dn 31 octo-line
number 100
label Customer Service
name Customer Service
call-forward busy 500
call-forward noan 500 timeout 12
ephone-dn 32 octo-line
number 101
label Sales
name Sales
call-forward busy 214
call-forward noan 214 timeout 12
ephone-dn 33 dual-line
number 260
label Conference Room
name Conference Room
call-forward busy 100
call-forward noan 100 timeout 12
ephone-dn 100
number 300
park-slot timeout 20 limit 2 recall
description Park Slot For All Company
ephone-dn 101
number 301
park-slot timeout 20 limit 2 recall
description Park Slot for All Company
ephone-dn 102
number 302
park-slot timeout 20 limit 2 recall
description Park Slot for All Company
ephone-dn 103
number 700
name All Company Paging
paging ip 239.1.1.10 port 2000
ephone-dn 104
number 8000...
mwi on
ephone-dn 105
number 8001...
mwi off
ephone-dn 106 octo-line
number A00
description ad-hoc conferencing
conference ad-hoc
ephone-dn 107 octo-line
number A01
description ad-hoc conferencing
conference ad-hoc
ephone-dn 108 octo-line
number A02
description ad-hoc conferencing
conference ad-hoc
ephone 1
device-security-mode none
mac-address 001F.CA34.88AE
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:2 2:31
ephone 2
device-security-mode none
mac-address 001F.CA34.8A03
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:12
ephone 3
device-security-mode none
mac-address 001F.CA34.898B
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
ephone 4
device-security-mode none
mac-address 001F.CA34.893F
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
ephone 5
device-security-mode none
mac-address 001F.CA34.8A71
ephone-template 1
max-calls-per-button 2
username "susan"
paging-dn 103
type 7931
button 1:6
ephone 6
device-security-mode none
mac-address 001F.CA34.8871
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:7 2:31 3:32
ephone 7
device-security-mode none
mac-address 001F.CA34.8998
ephone-template 1
max-calls-per-button 2
username "matthew"
paging-dn 103
type 7931
button 1:9
ephone 8
device-security-mode none
mac-address 001F.CA36.8787
ephone-template 1
max-calls-per-button 2
username "nate"
paging-dn 103
type 7931
button 1:10
ephone 9
device-security-mode none
mac-address 001F.CA34.8805
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:5
ephone 10
device-security-mode none
mac-address 001F.CA34.880C
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:14
ephone 11
device-security-mode none
mac-address 001F.CA34.8935
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:3
ephone 12
device-security-mode none
mac-address 001F.CA34.8995
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:8 2:31
ephone 13
device-security-mode none
mac-address 0021.5504.1796
ephone-template 2
max-calls-per-button 2
paging-dn 103
type 7931
button 1:4
ephone 14
device-security-mode none
mac-address 001F.CA34.88F7
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:23
ephone 15
device-security-mode none
mac-address 001F.CA34.8894
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:26
ephone 16
device-security-mode none
mac-address 001F.CA34.8869
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:28 2:27
ephone 17
device-security-mode none
mac-address 001F.CA34.885F
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:11
ephone 18
device-security-mode none
mac-address 001F.CA34.893C
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:27
ephone 19
device-security-mode none
mac-address 001F.CA34.8873
ephone-template 1
max-calls-per-button 2
paging-dn 103
type 7931
button 1:27
ephone 20
device-security-mode none
mac-address A456.3040.B7DD
paging-dn 103
type 7942
vpn-group 1
vpn-profile 1
button 1:13
ephone 21
device-security-mode none
mac-address A456.30BA.5474
paging-dn 103
type 7942
vpn-group 1
vpn-profile 1
button 1:15 2:16 3:32
ephone 22
device-security-mode none
mac-address A456.3040.B72E
paging-dn 103
type 7942
vpn-group 1
vpn-profile 1
button 1:1
ephone 23
device-security-mode none
mac-address 00E0.75F3.D1D9
paging-dn 103
type 7936
button 1:33
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 67
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
transport input all
scheduler allocate 20000 1000
ntp master
ntp update-calendar
ntp server 216.228.192.69
webvpn gateway sslvpn_gw
ip address 66.111.111.111 port 443
ssl encryption 3des-sha1 aes-sha1
ssl trustpoint cme_cert
inservice
webvpn context sslvpn_context
ssl encryption 3des-sha1 aes-sha1
ssl authenticate verify all
policy group SSLVPNphone
functions svc-enabled
hide-url-bar
svc address-pool "SSLVPNPhone_pool" netmask 255.255.248.0
svc default-domain "bendbroadband.com"
virtual-template 1
default-group-policy SSLVPNphone
gateway sslvpn_gw domain SSLVPNphone
authentication certificate
ca trustpoint cme_root
inservice
end

I think your ACL could be the culprit.
ip access-list extended router-access
permit tcp any host 66.111.111.111 eq 443
Would you be able to change the entry to permit ip any any (just for testing purpose) and then test to see if the calls function properly. If they work fine then we know that we need to open som ports there.
Please remember to select a correct answer and rate helpful posts

CCM intergrate with CME!!!

Similar Messages

Maybe you are looking for