CCNP Lab setup

Hi Guys,
I've to propose a cisco equipment list to setup a complete lab for "CCNP R&S" course, this lab setup should be able to simulate the entire course contents/theories of the three modules including route, swithc and Tshoot).
So what is the recommended lab setup to met the above requirment? Further we are looking forward to purchase new equipment, rather than considering the re-purbished equipments. Please advise.
Regards,
Suthakar

Depends on your budget, of course.
To cover the switch portion, you would want two 3560 models (3560, 3560G, 3560E, 3560X, depending on how much money you have to burn) and two 2960 models (again, G, PoE, etc) depending on what you're after.
For routers, I haven't finished building my lab yet, but I'd want 1841's or 19xx's. Something that can run 15.x code. I think to really run anything, you'd want at least 4 routers, plus serial WIC-1T cards, serial crossover (DB-60) cables, and at least a 4 port serial module for one router. I'd probably want at least one big router, like a 3845 or 39xx.
I'd probably want 4 18xx/19xx remote site routers, and 1 38xx/39xx hq site router. You can use GNS3 to simulate the routers though really, so most of my focus has been on switches.
Good luck!
Andy

Similar Messages

Lab setup multiple SIP domains for federation

I have been setting up multiple Lync 2013 lab environments and have a question about my external DNS environment. I have installed server 2012R2 on the host running the lab with its own domain (contoso.local). I have this server which hosts a separate domain,
Hyper-V and a CA, this is what I am using for my external environment. The network IP is 10.0.0.0/16.
I set up a server called vRouter that has 3 NICs. In Hyper-v I have 3 virtual switches configured. One for the External environment - 10.0.0.0/16 (not necessary for lab, setup to transfer needed files from internet to VMs), one for 192.168.1.0/24, and one
with 192.168.2.0/24. The virtual router has RRAS installed and can route traffic between 192.168.1.0/24 and 192.168.2.0/24.
My VMs for the lab are as follows.
1test.local
AD1.1test.local -192.168.1.100
FE1.1test.local - 192.168.1.200
Edge1 - 192.168.1.210int, 10.0.5.10ext
2test.local
AD2.1test.local -192.168.1.100
FE2.1test.local - 192.168.1.200
Edge2.1test.local - 192.168.1.210int, 10.0.6.10ext
Both environments have users that can log into lync and message each other.
When installing the Edge servers I used the same FQDN and IP for the external interface since all ports are open and firewalls have been disabled internally. I installed the internal certificate from the AD server which has CA role in each environment. On
the external device I used the Host's CA to get certificates for both Edge servers. The Edge servers have 2 NICs one on their expected internal environment with no Gateway. And one on the external environment. These servers are not part of any domain. however
I did add the contoso.local to the primary DNS suffix when domain membership changes under system properties. I then created the two following A records on the host computer (10.0.0.0\16 network, contoso.local) to be able to see router their external traffic.
Edge1.contoso.local 10.0.5.10
Edge2.contoso.local 10.0.6.10
Both of these FQDNs are what is in my topology for the Access Edge service, Web Conferencing Edge Service, and A/v Edge Service with the same IP using different ports in both environments.
Both environments are set up to support the other SIP domain. However when I try to add a user from the other domain I cannot communicate with that user nor see their presence.
I looked over my external DNS settings and realized that I had not set a SRV record on the 10.0.0.0\16 network(external).
I then realized that if I try to add the traditional _sipfederationtls._tcp.contoso.local I will have 2 conflicting entries.
One for:
_sipfederationtls._tcp.contoso.local - 10.0.5.10 (1test.local edge)
and one for:
_sipfederationtls._tcp.contoso.local - 10.0.6.10 (2test.local edge)
Should I spin up another VM and make that a DC with a CA and trust it to the host computer, set up conditional forwarders. Something like Trust.local and correct the DNS, topology builder FQDN, and certificates on the second edge server?
Edge2.trust.local
Or can I add a new zone to my host computer then correct the DNS, topology builder FQDN, Certificates?
Or am I missing another external DNS record on my contoso.local environment?
Can I set up a CNAME entry that will mask the second edge server?
Any input would be appreciated.
Thanks

If contoso.com is not a sip domain, then you won't need that DNS record at all. Those records are autodiscover records that Lync uses based upon the sip domain.
So you'd need
_sipfederationtls._tcp.1test.local
and
_sipfederationtls._tcp.2test.local
What effectively happens, is when someone on the outside tries to IM
[email protected], their Lync edge server will see the 1test.local and query the appropriate above record for it so it knows where to communicate.
Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question please click "Mark As Answer".
SWC Unified Communications

Exchange Server 2013 - Lab setup with internal emails only

Hi,
I'm new to Exchange Server 2013. I've started a POC on the product by setting up a Lab environment with one 1 AD server and 1 Exchange server (Both Windows 2012 R2). As this is a POC I just need the internal email communication. I don't want the mails to
go over the internet.
I've completed the installation part and just started to configure Send/Receive connectors and got stuck with the question whether the connectors are required or not.
Could someone please help me out in configuring internal email setup for Exchange 2013 lab setup.
Regards,
Nithin

Hi,
You need not to configure send/receive connectors for internal email.
The following article for your reference:
http://technet.microsoft.com/en-us//library/aa996395(v=exchg.150).aspx
Default Receive connectors created during setup
Certain Receive connectors are created by default when you install the Mailbox server role.
Default Receive connectors created on a Mailbox server running the Transport service
When you install a Mailbox server running the Transport service, two Receive connectors are created. No additional Receive connectors are needed for typical operation, and in most cases the default Receive connectors don't require a configuration change.
These connectors are the following:
Default <server name>   Accepts connections from Mailbox servers running the Transport service and from Edge servers.
Client Proxy <server name>   Accepts connections from front-end servers. Typically, messages are sent to a front-end server over SMTP.
Each connector is assigned a TransportRole value. You can use it to determine the role the connector is running in. This can be helpful in cases where you are running multiple roles on a single server. In the case of each Receive connector previously
mentioned, their TransportRole value is HubTransport.
To view the default Receive connectors and their parameter values, you can use the
Get-ReceiveConnector cmdlet.
Default Receive connectors created on a Front End Transport server
During installation, three Receive connectors are created on the Front End transport, or Client Access server. The default Front End Receive connector is configured to accept SMTP communications from all IP address ranges. Additionally, there is a Receive
connector that can act as an outbound proxy for messages sent to the front-end server from Mailbox servers. Finally, there is a secure Receive connector configured to accept messages encrypted with Transport Layer Security (TLS). These connectors are the following:
Default FrontEnd <server name>   Accepts connections from SMTP senders over port 25. This is the common messaging entry point into your organization.
Outbound Proxy Frontend <server name>   Accepts messages from a Send Connector on a back-end server, with front-end proxy enabled.
Client Frontend <server name>   Accepts secure connections, with Transport Layer Security (TLS) applied.
In a typical installation, no additional Receive connectors are required.
Niko Cheng
TechNet Community Support

Cmexpress7 lab setup

what could be your suggestion of a lab setup for learning cm7 express..
router=
switch=
phones=

Hello,
I have my CUCME 7x running on a 2801 router, with an AIM-CUE daughtercard for voicemail. I have a 3560 switch with PoE, and you can use any phone that the system supports. In my lab I have a couple of 7931's, some 7961's, and 7942's. It works like a charm.
Hope that helped, if so please rate.

CCNA/CCNP Lab Requirements

Hi
First post, this is totally in the incorrect place for some reason all of the categories are greyed out and this is the only place I can post this question. Hopefully the mod will inbox me and move this tread.
Anyway!!
Just starting out in the Cisco world, I’m changing career from a Project Manager within the construction industry so don’t have a clue about any of this stuff.
I’ve been studying for about one month from Tod Lams book, so far I’m learning the OSI etc etc.
Cisco is very interesting and I’ve got the bug and just want to play about now with hardware.
I’ve bought,
2 x Catalyst 2950 10Base-T 100Base-TX 24 Ports
3 x 1760 Routers all with a 60 pin serial card output and WIC-1AM Card
There are two empty slots on each router and its says they are for voice, I’ve not bought any voice cards for them yet because firstly I don’t know if the routers are going to get me through the CCNP.
Here’s the question!
I know the above equipment will get me through my CCNA but will it get me through my CCNP too. I’m planning to keep on learning until I reach CCIE so I want a lab that’s going to last at least until I have my CCNP.
Thank-you
Regards
James

Hi all
Right so now I'm looking at layer 3 switches....£££pricey£££!!!
Anyway it's all good :)
The guy I bought the AS2511-R2 from will combine the postage on another item so it makes sense to get this layer switch from him... eBay job :)
He's not got any 3560 or 3750s however he does have a WS-3550-48-SMI is that any good or should I get a the 3560?
So I've booted up the 1760 router and I have the following information below.
Router>sh ver
Cisco IOS Software, C1700 Software (C1700-ADVENTERPRISEK9-M), Version 12.4(8), RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 15-May-06 12:42 by prod_rel_team
ROM: System Bootstrap, Version 12.2(7r)XM2, RELEASE SOFTWARE (fc1)
Router uptime is 5 minutes
System returned to ROM by power-on
System image file is "flash:c1700-adventerprisek9-mz.124-8.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 1760 (MPC860P) processor (revision 0x600) with 92231K/6073K bytes of memory.
Processor board ID FOC09220W3G (2598069861), with hardware revision 0000
MPC860P processor: part number 5, mask 2
1 FastEthernet interface
1 Serial interface
1 Serial(sync/async) interface
1 terminal line
32K bytes of NVRAM.
32768K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
Also the 2950 I have is the following
Switch>sh ver
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(19)EA1c, RELEASE SOFTWARE (fc2)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Mon 02-Feb-04 23:29 by yenanh
Image text-base: 0x80010000, data-base: 0x8058A000
ROM: Bootstrap program is C2950 boot loader
Switch uptime is 1 minute
System returned to ROM by power-on
System image file is "flash:/c2950-i6q4l2-mz.121-19.EA1c.bincopy"
cisco WS-C2950-24 (RC32300) processor (revision R0) with 20808K bytes of memory.
Processor board ID FCZ0918W08U
Last reset from system-reset
Running Standard Image
24 FastEthernet/IEEE 802.3 interface(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:13:C3:D9:C6:80
Motherboard assembly number: 73-5781-13
Power supply part number: 34-0965-01
Motherboard serial number: FOC09142Z1P
Power supply serial number: DAB0910496R
Model revision number: R0
Motherboard revision number: A0
Model number: WS-C2950-24
System serial number: FCZ0918W08U
Configuration register is 0xF
Please let me know your thoughts because at the moment this may as well be in Japanese.
Thanks for reading
Sent from Cisco Technical Support iPhone App

Pre-requisite for lab setup for database administration track.

Hi, does anybody know what setup is required to participate in Lab for database administration track on Feb 11?

The code you have in the rules file looks like it is incorrect. PCon would not be defined automatically and would therefore return zero. I think what you are actually looking for is something like:
Call Hs.Con ("",HS.Node.PCon(""),"")
Note that you can determine if the consolidation rules are used from you metadata under AppSettings. Look for the setting called ConsolidationRules. If you set this to Y, it uses the rules under Sub Consolidate(), if you set it N, it will automatically consolidate even if you have nothing under Sub Consolidate().
Further, you can affect what gets consolidated in the metadata. Some of your accounts etc. may not be set correctly. Some things to check:
For Accounts, make sure that IsConsolidated is checked and the AccountType is correct
Also for Accounts, ensure that EnableCustom1Aggr ... is checked
Finally, if the Entities have different currencies, check if you are getting data up to [Parent Total]. If not, the problem is your translation and not your consolidation.

UCCE 9.0.1 Lab Setup Sprawler

Hi,
I am trying to setup ucce 9.x lab as a Sprawler meachine. But when I try to run the UCCE Web admin page, I need to selct a deployment model. It doesn't let me select anything other than PCCE Lab only, which will cut down the configuration options in my lab. Anyone know if I want to use complete UCCE(not PCCE) in lab as a sprawler meachine, how can i do it?
Thanks

Hi Alejandro,
This error will normally come if u try open domain manager without installing the base setup of ICM. try installing ICM base setup first and then run Domain manager. You should not see that issue.
Hope this helps.
Thanks,
Ganapathi.S

Standalone ASA Lab setup context disabled

                   I've built a lab with two standalone ASA with no failover unit in firewall router and multiple context mode with failover active setup on each to make them act as primary and to simulate two separate Data Centers and DMZs. When I do a show failover on a context I get the message that shows the context disabled. What do I need to do make the context active on each standalone unit?
asalab03# sho fail
Failover Off
Failover unit Primary
Failover LAN Interface: not Configured
Unit Poll frequency 1 seconds, holdtime 15 seconds
Interface Poll frequency 15 seconds
Interface Policy 1
Monitored Interfaces 0 of 250 maximum
asalab03# changeto con C
asalab03/C# sho fail
Failover Off
Last Failover at: 12:56:49 UTC May 18 2012
        This context: Disabled
                Active time: 0 (sec)

Hellom
Have you already assigned a context to one of the failover groups?
hostname(config)#failover group 1
hostname(config-fover-group)#primary
hostname(config-fover-group)#exit
hostname(config)#failover group 2
hostname(config-fover-group)#secondary
hostname(config-fover-group)#exit
hostname(config)#context context_name
hostname(config-context)#join-failover-group {1 | 2}
hostname(config-context)#exit
You can share the configuration if this step is already done.
Regards.
Do rate all the helpful posts
Julio
Cisco Security Engineer

WLC 2125 - Lab setup

Good Afternoon,
I'm trying to setup a WLC lab here at work and I'm having a few issues. I'm trying to plug an AP directly into the WLC and I'm having issues with the AP getting an IP using the Internal DHCP server option.
Is this setup not going to work without a switch involved? Unfortunately, I don't have a switch available for use, but I'm trying to find anyway to setup this controller to have DHCP that can serve my AP an IP address to join the controller.
Any advice or help will be grateful. I can also provide my management and ap-manager information if needed. Also, I do have DHCP proxy enabled.
Matt Cooper

Hi.
the internal DHCP server is for clients. it can provide IPs to clients that connect over wireless. It does not provide IPs to anything on the wired side. So, its not going to work with your situation.
If you can't set up a switch and configure it with a DHCP pool to serve the APs what you can do is to configure a static ip on the AP.
check here: http://goo.gl/tEOdAa
Note: in the commands in the above link, if the keyord "lwapp" didn't work with you you try using the keyword "capwap". (using of either keywords depends on your AP model).
Regards,
Amjad

CCENT/CCNA/CCNP LAB - router/switches

Hello - I recently inherited the following equipment (below). I wanted to know if I could still train with this and if so, for how long before I need to add/replace equipment. I was told this could assist me upto CCNP. Thank you for all replys.
I'm currently interested in the Cisco Security path.
3 x 2610
2 x 2611
2 x 2503
1 x 2504
1 x 2511
1 x 2523
1 x Catalyst 1900
1 x Catalyst 2950
1 x VoIP Cisco Phone
1 x Frame Relay Switch

Hi kwarren7677
Your equipment seems strong enough for the CCNP R&S , but if you want to focus on the security path you have to add an ASA maybe an ASA5505 and make sure the IOS running on the devices are K9 images to have the full security features enable.
Also would be great to have an IPS, but I think they are too expensive to make up a lab , it's better is you use the integrated IPS solution or buy a IPS module for the ASA.
Rate helpful post !!
Hope this helps
- Randy -

SCCM 2012 Test Lab Setup Questions...

Hi all,
I'm trying to set up a SCCM test lab with VMs so I can test deployment of our software package (.msi). I downloaded the System Center 2012: Configuration Manager Test Lab Guide, which appears to consist of the following required machine setups...
-One server running System Center 2012 Configuration Manager named CM1. CM1 uses the Windows Server 2008 R2 SP1 Enterprise Edition operating system.
-One pre-existing server running SQL Server 2008 R2 Enterprise named APP1. APP1 uses the Windows Server 2008 R2 SP1 Enterprise Edition operating system.
-One pre-existing client running on Windows 7 Ultimate Edition named CLIENT1.
From this document, the first step is to Complete the Base Configuration. When I download that document, it lists the following needed systems...
One computer running Windows Server 2008 R2 Enterprise Edition named
DC1 that is configured as an intranet domain controller, Domain Name System (DNS) server, Dynamic Host Configuration Protocol (DHCP) server, and an enterprise root certification authority
(CA).
One intranet member server running Windows Server 2008 R2 Enterprise Edition named
APP1 that is configured as a general application and web server with secure sockets layer (SSL) support. APP1 also hosts the certificate revocation list (CRL) for the enterprise root CA
installed on DC1.
One roaming member client computer running Windows 7 Enterprise or Ultimate named
CLIENT1.
One intranet member server running Windows Server 2008 R2 Enterprise Edition named EDGE1 that is configured as an Internet edge server.
One standalone server running Windows Server 2008 R2 Enterprise Edition named
INET1 that is configured as an Internet DNS server, web server, and DHCP server.
The Base Configuration test lab consists of two subnets that simulate the following:
The Internet, referred to as the Internet subnet (131.107.0.0/24).
An intranet, referred to as the Corpnet subnet (10.0.0.0/24), separated from the Internet subnet by EDGE1.
My question(s)... How many separate VMs are required to set up the test lab, 7? Or are APP1 & CLIENT1 the same system for both setup guides, which I guess would bring the total of needed systems/vms to 5?
Can any of the images serve a dual purpose to lessen the number needed even further?
Any information would be greatly appreciated!
THANKS IN ADVANCE!!

There's no correct answer here as ConfigMgr itself can run on a single server or its roles can be spread out to many different servers. Ultimately, in a pure lab, there is rarely a reason to use more than a single server unless you are trying to simulate
a production deployment where the roles have been separated.
This single server doesn't include a DC though (as the ConfigMgr site server must be a member of an AD domain) or a client to manage though so that brings the total up to 3. You technically could put the ConfigMgr site server on the DC; however, that
is rarely done in production and cause a few unique configuration issues. You could also treat the DC as your managed client but that's typically not a great use case for testing client management.
I have no idea what lab guide you are following, but remember the lab guide is set up to walk you through many different scenarios -- some of which you many not care about. ConfigMgr is a huge and complex application that can be installed in many, many different
configurations based upon the goals of the installation and the organization it supports so it ultimately depends upon exactly what you are after. I'd suggested doing some additional supplemental reading like TechNet and/or one of the publishes books
available instead of just blindly following the lab guide. That's not to say the lab guide doesn't have value, but if you want to follow it, then you need to follow it.
Jason | http://blog.configmgrftw.com | @jasonsandys

Home LAB Setup Advice

Dear All,
I would like to know and get advices from you guys how to setup home lab?
The configuration i have
1 server with below mentioned config
Intel Xeon 2.3Ghz dual Processors in Intel s5000PSL Motherboard
12GB RAM
500GB SATA HDD
Rackable Server with Virtualization Bios enabled
I have installed Windows 2012 R2 Datacenter Evaluation for 180 days and i have setup Domain Controller and HYPERVServer in that Machine
I have created 3 Virtual Machines in that Server
1. Domain Controller Windows 2012 R2 Datacenter Eval
2. Additional DC same windows 2012 R2 Datacenter Eval
3. Win 7 64bit Client VM for me to test
Please advice me i need to configure more servers in this HyperV Server and to learn
Please advice what servers i can configure to setup home lab to learn and practice.
I need to install exchange 2013 also in my mind.I have aDSL at my home with domain name.
Your Valuble inputs are appreciated.
Thanks in advance
Tony

Hi Sir,
>>Please advice me i need to configure more servers in this HyperV Server and to learn
>>Please advice what servers i can configure to setup home lab
to learn and practice.
I agree with Tim .
Actually you can install any OS in the guest OS list to build what the lab you want :
https://technet.microsoft.com/en-us/library/dn792027.aspx
Best Regards,
Elton Ji
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] .

Lab setup- 2911/CME, aironet AP, and 7926

I need to setup a lab for testing / demo 2 7926 phones to call each other.
Do you have a simple sample CME config to accomplish this (ie, ephone command, realtive show commands to prove it connected or not)?
Can I plug my AP directly into the ethernet port on the 2911? If not will any switch do?
Also, there will be a VMXL server added later, where does this get connected physically?
Let me know on this sample config what else I would need to setup the phones. Thanks so much.

You have to plug your AP to PoE switch port configured as trunk port (assuming multiple vlan trunk to wireless network) if you are using it standalone mode (without WLC). If your switch is not POE then you need power injector to power the AP.
Then you have to configure necessary SSIDs to phones to join via wirelessly & register to your CME. In DHCP scope for the phones you need to provide option 150 which is CME IP address.
Do not know about VMXL server connetion.
HTH
Rasika

UCCE Lab Setup

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin-top:0in;
mso-para-margin-right:0in;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0in;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
Hi All
Can any one point me in the right direction on setting up a home UCCE CVP lab, I have all the Media and Lic File, how hard is it and is following Hardware enough.
I have downloaded the SRND, and Install Guide looking for more detail doc.
3 VMware Servers 24GB memory and 2 TB HD on each Server
2811 SIP gateway

I try to Setup the i am getting all kind of error and I was wondering
if there any Guide on the installs. SRND is every brief on the how works, but it’s hard
So Far what I have is only the CCM Custer and UCCE OS install for the Cluster
ICM 8 I have download the OVA template try to the do install based on the doc I have it not working right,
Any help will be grate…
Thank you for your help
Captin S

Voice lab setup

Hi,
I have a router 2811 and wanted to create a voice lab with max 5 ip phones.So i wanted to know what are the minimum devices and modules required for voice lab.I have read in a document stating that for voice requirement are
two cisco router,two pvdm2-32 and two vic2-2fxs and two vic2-2fxo .
What else do i need ?Please help
Regards
Aateek Singh
Network Engineer
Spooster IT Services

here is my lab equipements and config
PSTN Router:
PSTN_Router# sh inv
NAME: "2811 chassis", DESCR: "2811 chassis"
PID: CISCO2811 , VID: V02 , SN: FTX0952C2MF
NAME: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN: FOC14265LNF
NAME: "PVDMII DSP SIMM with four DSPs on Slot 0 SubSlot 4", DESCR: "PVDMII DSP SIMM with four DSPs"
PID: PVDM2-64 , VID: V01 , SN: FOC10252G0F
Branch1 Router:
VLAB-R1#sh inventory
NAME: "2811 chassis", DESCR: "2811 chassis"
PID: CISCO2811 , VID: V02 , SN: FTX1011A10J
NAME: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0", DESCR: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1"
PID: VWIC2-1MFT-T1/E1 , VID: V01 , SN: FOC13285C42
NAME: "PVDMII DSP SIMM with four DSPs on Slot 0 SubSlot 4", DESCR: "PVDMII DSP SIMM with four DSPs"
PID: PVDM2-64 , VID: V01 , SN: FOC14022CEA
and configs: this is only T1 config. you also need to create dial-peerCME phone registrations etc.
PSTN:
card type t1 0 0
network-clock-participate wic 0
controller T1 0/0/0
clock source internal
cablelength short 110
pri-group timeslots 1-24
interface Serial0/0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn protocol-emulate network
isdn incoming-voice voice
isdn negotiate-bchan resend-setup
no cdp enable
Branch1:
card type t1 0 0
network-clock-participate wic 0
controller T1 0/0/0
cablelength short 110
pri-group timeslots 1-24
interface Serial0/0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
no cdp enable
I think thats enough to built T1 connection between routers.
test commands
PSTN_Router# sh voice port summary
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
=============== == ============ ===== ==== ======== ======== ==
0/0/0:23 01 isdn-voice up dorm none none y
0/0/0:23 02 isdn-voice up dorm none none y
0/0/0:23 03 isdn-voice up dorm none none y
0/0/0:23 04 isdn-voice up dorm none none y
0/0/0:23 05 isdn-voice up dorm none none y
0/0/0:23 06 isdn-voice up dorm none none y
0/0/0:23 07 isdn-voice up dorm none none y
0/0/0:23 08 isdn-voice up dorm none none y
0/0/0:23 09 isdn-voice up dorm none none y
0/0/0:23 10 isdn-voice up dorm none none y
0/0/0:23 11 isdn-voice up dorm none none y
0/0/0:23 12 isdn-voice up dorm none none y
0/0/0:23 13 isdn-voice up dorm none none y
0/0/0:23 14 isdn-voice up dorm none none y
0/0/0:23 15 isdn-voice up dorm none none y
0/0/0:23 16 isdn-voice up dorm none none y
0/0/0:23 17 isdn-voice up dorm none none y
0/0/0:23 18 isdn-voice up dorm none none y
0/0/0:23 19 isdn-voice up dorm none none y
0/0/0:23 20 isdn-voice up dorm none none y
Oper is dorm. it means everithing is good

CCNP Lab setup

Similar Messages

Maybe you are looking for