CD drive dead (but dvd's boot)???

Help!
A few monthes ago my internal CD reader/writer started acting funnny. Some days the door would not open and close, and it would mysteriously not show up in my system profiler. On other days only itunes would work to open and close the doors, and it would ONLY read music cd's not data cd's. THEN it disappeared completely and did not show up in the profiler, doors did not open and close. NOW it shows up in the profiler, and door will open and close - but
it will not read (or write) ANY cd i put in it. MEANWHILE DVD's work just FINE when put in.
my CD drive (internal) is a PHILIPS CDD5101, firmware A3.5
I have a G4 (mirror doors) Dual 867 MHz PowerPc (2.1)
I am running system X 10.4.11
and also have system 9 loaded (to run some old software i have not upgraded)
9 does not start up until i open old software so it isn't running in the back
ground all the time.
I have tried everything - does anyone have any ideas?
thanks - kimbat

I'm having very similar issues the past couple days with the Apple Combo Drive in my G4 867 MDD (i.e., door won't open, optical drive not showing up in profiler, iTunes cannot find a burner, etc). I opened the case and removed/reconnected the cables, then it worked fine, but a couple hours later the same symptoms showed up again... then disappeard for a while before returning. I have yet not checked to see if reads disks when its functioning. Pretty sure this is the original factory installed Apple combo drive.
Hoping to determine whether this is a system or hardware issue before purchasing a new drive. I did notice that when switching to another user account the problem didn't show up, but an hour or so later it did. A couple things I'll try later today when I get a chance -
- create a new user account with admin privs and see if the problem persists
- run disk utility from the tiger disks (if the drive is up and functioning)
Any other suggestions would be appreciated. Will report back on whether any of this helps.

Similar Messages

Hard drive detected but will not boot Windows Vista or recovery disk

Hi,
I have a very similar issue with a HP Pavillion a6355.uk, the hard drive kept crshing windows and then it finally just kept getting pass the HP boot menu options, and then all I get is the DOS "@press ctrl+alt+del to restart".
The hard drive is detected and passes all the tests, after pressing F9, going into the F10 options. F11 does not do anything, so cannot recover windows/the system.
I have tried changing the SATA connections on the motherboard, no difference. I tried the recovery boot disk I created when it was working and it will not boot with the old or new hard drive I bought to replace it (same size and compatable).
I cannot find where to partition the new hard drive or format the c: on the old one (it had D: for the recovery, but as it won't boot, cannot access this).
I have also tried the HP website to dowload the drivers for the new one, but the page does not load up to show any drivers or Windows to download.
http://support.hp.com/gb-en/product/HP-Pavilion-a6300-Desktop-PC-series/3644673/model/3671505/driver...
The next page just keeps looping or not proceeding when I put in details.
I can’t find anywhere to get hold of my copy of windows vista for this PC or get a disk to re-install on a new drive or fix the old detected drive, can someone please help!!

Just what size HD and is the drive Sata II or Sata III?
Vista 32bit .iso You must have a valid installation key, which should be on the COA sticker on the computer, to activate the installation once it completes. ImageBurn to create the .iso disk. Driver page Vista (not 64 bit)
I am a volunteer. I am not an HP employee.
To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
(2) HP DV7t i7 3160QM 2.3Ghz 8GB
HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Both Customs use Rosewill Blackhawk case.
Printer -- HP OfficeJet Pro 8600 Plus

Can't boot on hard drive or CD/DVD - grey/gray screen of death

A few weeks ago my PowerPC G5 Dual Processor running Leopard OS X froze while the screen saver was running. I hard-powered-off the computer --> held down power button for ~10 seconds. When I tried to start up again, I got the "gray/grey screen of death" with the Apple logo. The screen hung there and then fans starting ramping up to full speed with no sign off boot up. I know others have posted similar issues, but I wanted to start a new thread.
Basic Specs:
PowerPC G5 Dual 2.5 Hz Processors
4 Gb memory (recently upgraded form 2 to 4) ***
Bought in early 2005 (I think)
Here's a summary of what I've tried:
DOES NOT WORK
- booting up holding down C (for drive) --> straight to kill screen
- booting up from original discs for G5 (from both C mode and Option mode)
- booting up from 10.5 Leopard disc (from both C mode and Option mode)
- booting up holding down Option-Comman-P-R --> straight to kill screen
DOES WORK
- connecting to secondary computer using target mode (holding down T) - I can see both of my hard drives
- booting up holding down Option - I can select either my main drive (secondary is not present there but there is no OS on it) or CD/DVD in slot
- booting from Apple Hardware Test (AHT) disk from Option menu
-- I ran disk checks, had errors. I ran Disk Warrior from secondary computer in target mode and repaired the drive, running the AHT test again shows no errors
- ran disk repair from secondary computer to fix errors (using disk utility and disc warrior)
OTHER THINGS I'VE DONE
- replaced backup battery on motherboard that was weak at only ~70 mV with fresher battery at ~3.6V
- held down PMU (not SMU) reset button for 30 seconds
- (main fans were cleaned a few weeks before issue)
- two weeks before issue I installed more memory (from 2 Gb to 4 Gb with two new 1 Gb cards)
- backed up data - so I can delete drives if needed
THOUGHTS
- I'm concerned that under CPU it shows 158950.77 GHz - shouldn't it be showing two CPU?
- the drives look healthy when looking at them in target mode
- issue is occurring between power up and drive selection (since CD/DVD is also not viewable)
- maybe the new memory caused local over heating to the motherboard?
- I may be able to replace the heat sink, but the spare computer I have access to has different looking hardware. It's probably a different model of the G5. My computer has one metal case cover and the extra one has a split case cover.
NEXT STEP
- I need to back up secondary drive fully first
- pull out new memory sticks
- pull out all memory except originals
- pull out secondary drive
LAST RESORT
- buy external case for drives and cry about how no one will buy my dead desktop
Because this is a long description, I will post updates in the comments and a final comment here:
(Coming Soon)

The final lines in the log were all iTunes, but I think it's a hardware issue that's preventing me from booting.
Here is the line that includes the world "fatal" and a few lines before and after (it was the day before the crash):
Oct 9 02:05:50 Rys-Big-One com.apple.SystemStarter[28]: kextunload: unload kext /System/Library/Extensions/CiscoVPN.kext succeeded
Oct 9 02:05:51 Rys-Big-One kernel[0]: CiscoVPN : unloading cisco ipsec kernel module.
Oct 9 02:05:50 Rys-Big-One com.apple.SystemStarter[28]: Stopping Adobe Version Cue ...
Oct 9 02:05:50 Rys-Big-One vpnagent[88]: Termination reason code 7: The agent has been stopped.
Oct 9 02:05:51 Rys-Big-One kernel[0]: CiscoVPN : detaching from interface: en0.
Oct 9 02:05:50 Rys-Big-One vpnagent[88]: Function: getDownloaderMessage File: MainThread.cpp Line: 964 Invoked Function: CVpnMgr::processEvents Return Code: 0 (0x00000000) Description: fatal error, stopping service
Oct 9 02:05:51 Rys-Big-One kernel[0]: CiscoVPN : interface en0, filter has been safely detached.
Oct 9 02:05:51 Rys-Big-One vpnagent[88]: Cisco AnyConnect VPN Client Agent stopped, version 2, 4, 0
Oct 9 02:05:51 Rys-Big-One com.apple.SystemStarter[28]: Using CATALINA_BASE: /Applications/Adobe Version Cue/tomcat
Here is the last lines in the log:
Oct 10 15:59:53 Rys-Big-One com.apple.usbmuxd[26]: MuxSendToClient send failed for 0x1-ef497a0f0338225857a1061ea364e83ba6c46aa7@0x4b400000:64988->0x20da60-iTunes/ com.apple.iTunes:336: 32 - Broken pipe
Oct 10 15:59:53 Rys-Big-One com.apple.usbmuxd[26]: HandleUSBMuxDictionary client 0x20da60-iTunes/com.apple.iTunes using library usbmuxd-211 built on May 16 2011 at 00:10:00, running usbmuxd-211 built on May 16 2011 at 00:14:52
Oct 10 16:00:08 Rys-Big-One com.apple.usbmuxd[26]: HandleUSBMuxDictionary client 0x20e4d0-iTunes/com.apple.iTunes using library usbmuxd-211 built on May 16 2011 at 00:10:00, running usbmuxd-211 built on May 16 2011 at 00:14:52
Oct 10 16:00:09 Rys-Big-One com.apple.usbmuxd[26]: HandleUSBMuxDictionary client 0x20da60-iTunes/com.apple.iTunes using library usbmuxd-211 built on May 16 2011 at 00:10:00, running usbmuxd-211 built on May 16 2011 at 00:14:52
Oct 10 16:00:09 Rys-Big-One com.apple.usbmuxd[26]: HandleUSBMuxDictionary client 0x20da60-AppleMobileDeviceHelper/com.apple.SyncServices.AppleMobileDeviceHelper using library usbmuxd-211 built on May 16 2011 at 00:10:00, running usbmuxd-211 built on May 16 2011 at 00:14:52
Oct 10 16:00:09 Rys-Big-One com.apple.usbmuxd[26]: HandleUSBMuxDictionary client 0x20d740-iTunes/com.apple.iTunes using library usbmuxd-211 built on May 16 2011 at 00:10:00, running usbmuxd-211 built on May 16 2011 at 00:14:52
Oct 10 16:00:20 Rys-Big-One com.apple.usbmuxd[26]: HandleUSBMuxDictionary client 0x20e4d0-iTunes/com.apple.iTunes using library usbmuxd-211 built on May 16 2011 at 00:10:00, running usbmuxd-211 built on May 16 2011 at 00:14:52
Oct 10 16:00:50: --- last message repeated 1 time ---
Oct 10 16:01:20 Rys-Big-One com.apple.usbmuxd[26]: HandleUSBMuxDictionary client 0x20e4d0-iTunes/com.apple.iTunes using library usbmuxd-211 built on May 16 2011 at 00:10:00, running usbmuxd-211 built on May 16 2011 at 00:14:52
Oct 10 16:02:20 Rys-Big-One com.apple.usbmuxd[26]: HandleUSBMuxDictionary client 0x20e4d0-iTunes/com.apple.iTunes using library usbmuxd-211 built on May 16 2011 at 00:10:00, running usbmuxd-211 built on May 16 2011 at 00:14:52
Oct 10 16:03:20 Rys-Big-One com.apple.usbmuxd[26]: HandleUSBMuxDictionary client 0x20e4d0-iTunes/com.apple.iTunes using library usbmuxd-211 built on May 16 2011 at 00:10:00, running usbmuxd-211 built on May 16 2011 at 00:14:52
Oct 10 16:04:21 Rys-Big-One com.apple.usbmuxd[26]: HandleUSBMuxDictionary client 0x20e4d0-iTunes/com.apple.iTunes using library usbmuxd-211 built on May 16 2011 at 00:10:00, running usbmuxd-211 built on May 16 2011 at 00:14:52
Oct 10 16:04:23 Rys-Big-One iTunes[146]: _NotificationSocketReadCallback (thread 0xa03d1820): Unexpected connection closure...
Oct 10 16:04:23 Rys-Big-One iTunes[146]: AMDServiceConnectionSendMessage (thread 0xa03d1820): Could not send message size: Broken pipe

Dvd drive dead...and MANY more problems

hi there,
I had a bad sector on my hard drive, so i couldn't boot my machine. I had a diskwarrior cd, so i rebuilt the volume. AFter process, the machine restarted, and ejected the cd. I went to put it back in, and pop grrrrr buzz dvd drive crapped out...mechanically. I've restarted a few times since, in verbose mode, and it hangs up waiting for a cd...so i'm guessing the machine needs the diskwarrior cd present to finish the rebuilding job. how ultimately annoying.
i went out and bought, absolutely hesitatingly, a torx set which would open the 'scenester' screws on my tibook. took the optical drive out, and obviously the part that i beleive is unhinged/broken is hidden under a metal surface.
so now here's my thing. all i want is to start my bloody machine again. i rarely use the optical drive int he first place...so i'd consider an external drive. i dont need a fancy superdrive or anything as well. infact i'm skeptical about buying any other model optical drive, as i dont have the capability to install supplementary drivers...as my machine wont boot
i also can't afford the absurd price for the replacement (cw-8121-c), i've seen it a bunch of places for 200$USD. I'm a dead broke recent student. I'm fairly sure if i can't find a solution for under 50$ then it's over with apple and I.
So basically what this is, is a general call for anything sensical. I'm open to any suggestions anyone may have, and my gawd would i be thankful. I started as a mac person 15 years ago, but with my horrible track record im moving to 'indifferent' person status.
thanks in advance!

You could try this one on eBay perhaps, it's a risky one but it's no money so it may be worth it.

EMac optical drive: Reads but ceased writing. I get "Sense key=MEDIUM ERROR, Sense Code=0x0C, WRITE ERROR. Drive is Pioneer DVD-RW DVR-127D.

eMac optical drive: reads fine but has ceased writing. One day it's working fine, burning DVDs, then after repeated attempts stops copying and gives the following error message: "Sense key=MEDIUM ERROR, Sense Code=0x0C, WRITE ERROR". Drive is Pioneer DVD-RW DVR-127D. Is this a software issue or is the drive half dead? Get the same result with either Popcorn or Toast 10.

Are you using Roxio Toast? That error seems to be discussed a lot in the Roxio forums. Scroll down this thread:
http://forums.support.roxio.com/topic/1686-the-drive-reported-an-error-sense-key medium-error-etc/
and you'll find a step-by-step troubleshooting scheme.

CD/DVD Drive only reads DVDS Not CD But the computer reads it as a DVD RW Drive!

CD/DVD Drive only reads DVDS Not CD But the computer reads it as a DVD RW Drive.the drive door say RW DVD+R DL,Compact Disk Rewritable,Ultraspeed,DVD Multi Recorder.I was Wondering if Windows Loaded the wrong Driver?My Laptop S/N IsCNF62612TZ And P/N Is EZ601UA#ABA And The Front Of My Monitor says Hp Pavilion Dv 1000 Entertainment Notebook PC,And The Service Tag Is dv1738od and the Sticker On The Back Of The monitor say Hp Pavilion dv5- 1235dx Entertainment notebook PC.it Cme Factory With Win xp and when i got it the os was corrupted.i tried to reinstall xp but disk said no hard found.so i booted it up with vista ultimate and then downloaded the drivers and stuff from the here.should i had downloaded the 64 bit set as well?

della wrote:
My toshiba tecra a2 can only read DVDs. I cant read any type of cd. Ive tried so many things. My laptop is running on xp service pack 3 with a mat**bleep**a DVD RAm UJ 820s. I can burn/run any type of DVD but cant do anything with cds. Ive tried unistalling the drive and that didnt work. Ive uninstalled the IDE drivers and that didnt work. Nothing seams to work. I cant use recovery cds because there CDS. Please Help!!!!!!!!!
It's probable that the CD 'side' of the combo drive has failed. That you cannot boot from the recovery CD is pretty much proof of the failure.

Unable to boot from hard drive or install dvd

Out of the the blue my powerbook won't boot up. I've tried to reset the PRAM, I've tried to verbose thing but all it said was that it couldn't establish a connection to the windowserver. I've even tried to power on holding the option key but the hard drive and install dvd both have x's on them. What can I do to get this thing working again?

Have you tried rebooting in safe mode? Failing that, have you tried rebooting from the install disc so you can run Disk Repair? For either of these tests, insert your system disc and follow the instructions here: http://support.apple.com/kb/TS1417
Good luck!

Bootcamp woes, unable to boot from USB and DVD drive reads all DVDs blank

My partner and I are completely unable to install Windows using Bootcamp. We have tried dozens of solutions on the internet.
2011 iMac (purchased in by me and my partner 2012) reads all DVDs as blank. We have (hilariously) another Mac, an MBP, that has the same exact problem. You'd almost think "Superdrives" eventually just stop working or something. So obviously we can't install Bootcamp on the iMac using a DVD.
But what about a USB stick? Well after modifying the plist file and writing a bootable Windows USB and trying to boot from that, we were greeted with the mysterious and apparently yet-unsolved "no bootable device" error.
So our iMac can't boot from USB drives or read DVDs. We've only owned it for two years. And this is the second Mac we've owned where the Superdrive has died. And we don't even use DVDs more than like once a year.
But anyway, can someone tell me what we're supposed to do if we want to install Windows aside from throwing money away to buy another Superdrive that is probably going to die again in a year? Maybe a way to make our mac boot from our USB stick? Something?
Thanks.

Should you have another drive with a MBR, use it to rule that issue out. Alternatively create a GPT on the flash drive and try to boot from it.
What options are there for the usb controller/boot priorities/order/options? Does the laptop recognize the usb flash when already in bios setup? Should there be any form of choosing the device to boot, use that with the flash drive in the socket, then switch it with the external drive.

When I check my boot SSD drive using Disk Utility under Mavericks, I often get "Incorrect number of extended attributes" errors. But if I boot off an external drive and check the same SSD, no errors are reported. Is this a bug in Mavericks?

When I check my boot SSD drive using Disk Utility under Mavericks, I often get "Incorrect number of extended attributes" errors. But if I boot off an external drive and check the same SSD, no errors are reported.
This happens not just with the SSD in my Mac Mini, but with another SSD in my MacBook (both now running Mavericks). So far as I know, all of the kit I am using is in good order (despite the file corruption reports). So I am beginning to wonder if it could be due to a bug in Mavericks? Both SSD drives have been formatted to MacOS Extended (journaled) format. Should I have used a different format, I wonder?
Has anyone else encountered this issue?
Does anyone have a solution?
Or an explanation that might help my investigation of the issue?
Thanks guys,

I understand that the Corsair Force 3 is not one of the SSD drives that are supported on Apple Macs.
I did try downloading and using Trim Enabler, but the error message came up both when it was off and when it was on.
I understand that not everyone thinks Trim Enabler is a good program, though there is a new version out now, so I may give it another try.

Mid-2009 MacBook Pro sees internal SATA hard drive, but will not boot from or format

I inherited a Mid-2009 MacBook Pro (15-inch, 2.53 GHz model) with a very strange issue.
It first presented itself as not being able to boot from the internal SATA hard drive that came with the computer. Nothing I tried could get it to boot, so I assumed the file system was corrupted beyond repair and booted from a CD to try to format the drive. Disk Utility on the CD would not format the drive, giving me strange error messages like "Unable to write to the last block of the device".
At this point I figured the drive itself must be toast, so I pulled it out and put another known-good SATA hard drive in, booted from CD, and attempted to format. Again, same error messages and an unsuccesful format.
So I had the bright idea of formatting one of the drives in an external enclosure and then putting it in the MBP to see if OS X would even install. No dice. Get a cryptic error message before installation even begins.
So I installed OS X on the drive in the external enclosure and put it in the MBP, and it attempts to boot, but never goes anywhere.
So to sum up, the symptoms I'm seeing:
MacBook Pro CAN see internal SATA hard drives.
MacBook Pro WILL NOT boot from any internal SATA hard drive and cannot format or install OS X to any internal SATA hard drive.
MacBook Pro WILL boot from any CD or external device and seems to work properly otherwise.
At this point I'm thinking it's one of two things: the hard drive ribbon cable or the SATA controller on the logic board.
Since the MacBook Pro seems to work completely fine other than this one issue, and will boot properly from both external devices and the CD (also a SATA device), I'm thinking and hoping that it's just the hard drive ribbon cable. From my searches online, I've heard that this batch of MacBook Pros is known to have issues with the hard drive ribbon cable, but it seems in most cases this manifests itself by the Mac not being able to see a drive at all.
I've done quite a bit of troubleshooting to get to this point, but right now I'm just looking for any feedback at all. Specifically I'd love to know a way I can easily test to see whether it's the logic board or the cable.

UPDATE: An interesting development!
I just tried a third known-good SATA hard drive, one which I believe supports SATA I only (but I'm not sure), and unlike the other drives that the Mac sees but cannot properly interact with, the Mac can't even see this one when I put it inside.
Frustrating as this may be, I believe I'm actually getting closer to a solution since my symptoms now appear to be closely aligned with people having SATA ribbon cable issues.
Onward!

Pavilion Laptop dv6-1230 DVD CD RW drive dead.

In lieu of shipping the computer to HP for warranty repair, Is it possible to get a warranty replacement from HP and swap it out myself. It would certainly be less costly to HP to just send me a new drive.
I'm have tech skills, but no experience with laptop repairs. Is DVD drive replacement an easy task on this product?
How do I apply to HP for a replacement drive, i.e.. what documentation or testing info might they require? The drive is: Optiarc DVD RW AD-7561s
Thank you for your advice.

man......

Optical drive does not read CD's but DVD's please help!

My disc burning read-out is:
HL-DT-ST DVD-RW GWA-4165B
when i place any type of CD in my optical drive, after a few seconds the drive ejects. When i place any type of DVD media in the optical drive it reads perfect. any one have a solutions please help..
G5 Mac OS X (10.4.5) Dual 2.3 GHz PowerPC G5

Well, I bought a CD/DVD cleaner kit, and nothing happened--it didn't even recognize that the cleaner disc was in there and it didn't do anything.
I checked for an optical drive update, but the only one I found was for older Macs for 4X DVDs, which had nothing to do with CDs. Since even music discs won't mount, nor will discs that mount on every other Mac in the house, Macs both older and newer than my G5 and discs both older and newer, I suspect my drive is toast. Dang.

Dvd/cd drive works but won't allow me to install new programs from disk, doesn't recognize the disk,

dvd/cd drive works but won't allow me to install new programs from disk, doesn't recognize the disk, what can I do?

Well I was able to obtain a work around download of Flash and it installed fine but Firefox tells me it needs updating so I go out, thinking I'm "IN" finally to update it and I get that issue of not being able to get the update for it. It's a regular laptop, not a touch screen or one of those new fangled ones for todays world. In fact it's a refurb so it's probably origin date was a year or so ago before all this MS stuff took off fully. So not understanding why I'm feeling like I'm being BLOCKED from getting the updated Flash I need and desire. If I click on the little "X" and tell it to ignore the warning the vid will play just fine but don't want to have to do that every time. Must be a better way.
Again, I'm sorry for posting in the wrong forum, getting this posted in the Flash forum was my desire but the way Adobe has this set up I just couldn't figure it out. I belong to ALLOT of forums and most are pretty straight forward but this one is confusing!

New Hard Drive, Mac partition cloned and boots fine, but I can't seem to get my BOOTCAMP (windows) partition to boot! Any ideas?

Hello all!
I got a new hard drive for my Mac Book Pro and an enclosure so I could clone the old partitions on to the new drive.
So I...
Put the new hard drive in the enclosure.
Booted up off an install disk and ran disk utility.
Copied the Mac and Bootcamp partitions over to the new drive that was connected VIA USB.
Turned off the computer, took the old hard drive out and put it in the enclosure.
Put the new hard drive in the Mac Book Pro.
Booted into Mac OSX with no problem.
When I rebooted held down the option key to boot into the windows side, it didn't show up as an option.
When I went back into the Mac side, I loaded Disk Utility and saw that I had the Mac partition, the BOOTCAMP partition, and a bunch of unallocated space. When I went into the System Preferences and set the target boot drive to the BOOTCAMP partition and restarted, I got some crazy error about there not being any bootable info on it.
That's where I am at. I have found other posts with people who are having the same problem, but I have yet to find a solution that doesn't involve me buying some 3rd party software. I know it has something to do with (what is called in Microsoft world) the Master Boot Record, but I don't know how to modify that to reflect that the BOOTCAMP partition is a bootable logical drive. I remember in MS DOS land there was some command line FDSK /something command that you would run (I think it was /MBR) to reset the MBR. To me though, all of these terms are shadowy figures in the Ether.
What do I do???
-Ricardo
p.s. I read somewhere to boot off the windows 7 disk and run the system repair tools. I tried that and no change.

I got it. It CAN be done. At least on 10.6
How I made it happen (for free) on Snow Leopard:
1) partition, dupe etc all that jazz that you know. Make the mac side work, which it seems we've all been able to do no issues. I used SuperDuper! It worked just fine. (Had it on a disk. I assume you could use any other free way of doing this.)
2) New hard drive running, I used bootcamp assistant to partition the new drive for a new Bootcamp. I don't know if it's necessary to make the new partition this way for some reason, but it's what the process ultimately included, so maybe try without, but it worked with.
3) Natively running original drive on the windows side. Used DirveImage XML to clone windows partition onto new drive connected externally.
4) Back on new hard drive running natively. (Sorry for all the switching.) You'll note that the new Bootcamp partition is NOT bootable at this point. It won't come up in the usual 'alt on startup' boot menu.
Download rEFInd and install on mac side. Technically this is freeware or w/e, but for the love of god, throw money at this man. He totally deserves it.
5) Restarting the computer, rEFInd's boot manager finally recognizes windows. But you'll find windows is a little messed up and still won't quite boot. Get out your Windows CD and pop it in. Do the 'alt boot' thing. Your boot menu options are now "EFI Manager," "Bootcamp," and "Windows Disk." Or some such. Holy Crap! It recognizes Windows!
6) Boot to the CD and tell it to repair the windows volume. It will. My computer also had to do a disk check next time I booted to Windows, which took for-stupid-ever, but eventually worked. (I went to bed in between.)
7) Everything is running smoothly. Plus, you get the rEFInd boot manager, which is also great.
Deets: I have a late 2010 MBP 13". Snow leopard/Windows 7 32-bit (long story) Moved from original 320GB seagate momentus to new 750GB Seagate Momentus XT.
Feel free to share/copy&paste this solution as you see useful. Cheers!

New Hard Drive and trying to reinstall OS. Have Hp Recovery Discs but DVD drive broke

Hi to all,
I just put a new hard drive in my HP Dv7. I also ordered recovery discs. When I tried to put the disc in I then found out my DVD drive is not working
My question is can I transfer the recovery disc to a USB flash drive and then boot from there?
I would appreciate any insight!!
Thank you in advance,
Marc
This question was solved.
View Solution.

You cannot copy from recovery DVD to USB.
What is the problem with the drive, do you have a boot DVD to try?
Please mark my post as SOLVED if it has resolved your problem. It helps others with similar situations.

CD drive dead (but dvd's boot)???

Similar Messages

Maybe you are looking for