CD Driver Issues after installing 11.1.4

After installing Itunes 11.1.4, my HP computer, running Windows 7, could no longer find the CD drive. Upon investigation, someone suggested I update my registry to remove some entries. I did the following:
Start, enter regedit in search bar,
Open regedit
Left hand menus click HKEY_LOCAL_MACHINE
SYSTEM
CURRENT CONTROL SET
CONTROL
CLASS
Then need to find {4D36E965-E325........... (are more figures but not needed)
on right hand window see if there is an upper filter or lower filter.....right click and delete the values if either are there.
RESTART...
This worked, but now Itunes complains every time I open it, saying some registry settings are missing for my CD drivers. I've used Itunes on this computer succssessfully for years, until this upgrade. Apple, whatever you did, please undo it. Horrible release...

Solving the iTunes Installation Problems in Windows
1. Apple has posted their solution here: iTunes 11.1.4 for Windows- Unable to install or open - MSVCR80 issue.
2. If the Apple article does not fully resolve the problem for you, then try Troubleshooting issues with iTunes for Windows updates - MSVCR80.

Similar Messages

Driver Issues After Installing Windows 8.1 Preview

Yesterday, I downloaded and installed Windows 8.1 Pro Preview, which I now regret because my wireless connection no longer works on my Lenovo IdeaPad N580. I check the status of the driver for the Realtek RTL 8192DE wireless LAN, and I get a message that I have the latest driver. However, when I check the status the the Realtek device, the system says it is disabled. I tried to enable it within BIOS as I read somewhere that that is the way to fix the problem, but I cannot find any reference to the wireless LAN device in BIOS. This problem has apparently happened a number of times on a number of brands of computers. Nothing I've read that I've tried works. Does anyone have any ideas?

zkeith wrote:
Yesterday, I downloaded and installed Windows 8.1 Pro Preview, which I now regret because my wireless connection no longer works on my Lenovo IdeaPad N580. I check the status of the driver for the Realtek RTL 8192DE wireless LAN, and I get a message that I have the latest driver. However, when I check the status the the Realtek device, the system says it is disabled. I tried to enable it within BIOS as I read somewhere that that is the way to fix the problem, but I cannot find any reference to the wireless LAN device in BIOS. This problem has apparently happened a number of times on a number of brands of computers. Nothing I've read that I've tried works. Does anyone have any ideas?
The only way I can think of is to erase your hdd and fresh install Windows 8 or 7.

Having issues after installing Essbase V9.3.1,configuring the SQL interface

I am having issues after installing Essbase V9.3.1 and configuring the SQL interface. we are using UNIX/AIX box for our Essbase server and UDB DB2 9.1 SP6 as our SQL Interface.
When tried to run an ESSCMD script to perform BUILDDIM operation on Essbase application using the load rule (with the SQL interface), got the error as recorded in the application log file and is attached at the bottom and the .odbc.ini file on the server looks as follows.
Can somebody tell me whether .odbc.ini needs any correction or what else should I do to correct the issue and able to work thru using SQL interface? Appreciate any help provided in this regard. Thanks,
.odbc.ini
[ODBC Data Sources]
DOLU003=IBM DB2 ODBC DRIVER
[DOLU003]
Driver=/home/db2inst1/sqllib/lib/libdb2.a
Database=DOLU003
[ODBC]
Trace=0
TraceFile=odbctrace.out
InstallDir=/home/db2inst1/sqllib/odbclib
[Mon Apr 20 15:16:29 2009]Local/New_Bud/Budget/Olapadm/Info(1021020)
Cannot read SQL driver name for [] from [home/hyperion/.odbc.ini]
[Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1013091)
Received Command [SQLRetrieve] from user [Olapadm]
[Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1021020)
Cannot read SQL driver name for [] from [home/hyperion/.odbc.ini]
[Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1021004)
Connection String is generated
[Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1021041)
Connection String is [DSN=DOLU003;UID=...;PWD=...]
[Mon Apr 20 15:16:43 2009]Local/New_Bud/Budget/Olapadm/Info(1021006)
SELECT Statement [SELECT * FROM DB2OLADM.BD_DIMENSION_DEF_PC WHERE DIMENSION_ID
= 12 ORDER BY TREE_NODE_NUM, PARENT_NODE, CHILD_NODE] is generated
[Mon Apr 20 15:16:44 2009]Local/New_Bud/Budget/Olapadm/Info(1021013)
ODBC Layer Error: [7] ==> [[DataDirect][ODBC 20101 driver]6013]
[Mon Apr 20 15:16:44 2009]Local/New_Bud/Budget/Olapadm/Info(1021014)
ODBC Layer Error: Native Error code [0]
[Mon Apr 20 15:16:44 2009]Local/New_Bud/Budget/Olapadm/Error(1021001)
Failed to Establish Connection With SQL Database Server. See log for more information
--------------------------------------------------------------------------------------------------------------------------------------------

I had similar errors when first setting up the SQL interface. Are you on a 64 bit operating system on the essbase server? If so Essbase needs to use the 32 bit odbc driver, not the default 64 bit driver.
The 32 bit driver is still available here SysWOW64\odbcad32.exe <-----This is the 32 bit (Use)
The Administrative tools by default uses system32\odbcad32.exe <----This is the 64 bit (Don't Use)
Once I opened the 32 bit driver interface directly and set it up the errors went away.

Issues after installing Classic on OS 10.4

Background and System
I have a Power Mac G3 350Mhz Rev 2 Blue and White, 512MB, 40GB, DVD ROM
running 10.4.9 installed from Retail DVD. Firmware up to date. 2x 20 GB partitions formatted as Extended
Prior to this issue OS X has been running well.
Issue:
After installing OS 9.2.1 to second partition OS X will now not boot up from DVD nor it's partition
Solutions tried:
I wanted to install a Classic environment so used a Retail OS 9.2.1 Bootable CD and did a full install to the second partition.
After the install finished and the system restarted, set on the OS X (Partition1) for start up the system hangs right after the Apple "Chime". with no signal to video card
Attempted to then boot from OS 10.4 DVD but this does not get detected when holding "c" down for boot up from CD option. This worked perfectly before.
Have run OS 9.2.1 Disk Aid Verify and both partitions are ok. The system will boot from the 9.2.1 CD and partition but anything to do OS X now will not work. I also tried an Ubuntu 6.06 Live CD but this will not now boot either.
Checked firmware and tried to re run firmware update and this advised my firmware was up to date.
Any other suggestions?
Thanks

The only thing I can think of is that when you installed the 10.4.9 OS you didn't option to install OS 9 drivers.

HT1923 how do you get the dvd drive back after installing itunes to windows 7

How do you get the dvd drive back after installing itunes to windows 7??

Safari/Preferences/General and set a new default.

Dreamweaver CS4 having issues after installing PS CS6 Beta

Hi All,
I'm having issues with Dreamweaver CS4 after installing Photoshop CS6 Beta. I'm getting the follwing erros when trying to open any html file (see attached image).
Once I click OK, the file will open, also now; any copy and paste commands will not work. Anyone else experiencing any problems with other apps after installing this beta version?
Any help and feedback is much appreciated, thanks!

Re :Re: Dreamweaver CS4 having issues after installing PS CS6 Beta
Just a thought ...
This may help!
Uninstall the Beta Version of Photoshop CS6 now and then restart your computer and see if that works.
Open the CS4 programs and see if that fixed the problem and it is all working as it should again.
It is worth a try!
All the best.

Issues after installing Mavericks

I am having a ton of issues after installing macericks on wed evening, on my MBP 15" 2.5 GHz i7 with 8GB of memory,
I have a task com.apple.internetaccouts, and com.apple.MailServiceAgent, taking upwards of 100% CPU at time and the fan will go full speed, and earlier today i had a msg come up that i had run out of usable memory and the sytem had paused programs, I have restarted a few times and still the same things are coming up and the system has become really slow.
would think that with this system not being that old, that i should not be having these types of issues, if there is something that someone could lead me to ths casue i thnk you
Thanks
Doug

Had this issue again today on my wife's iMac. This was after the Mail.app update that was recently released. I now have messed with this issue enough that I believe I have figured it out.
I used to have a plugin for Mail called HTTPMail that was used to access Hotmail prior to them having POP/IMAP. It seems that removing the account from Mail left some residual account details in the ~/Library/Mail/V2/MailData/Accounts.plist file. Mavericks Mail.app chokes on this account detail and starts duplicating it numerous times. That's why the Accounts.plist file grows so large.
If you open the Accounts.plist file in a text editor (TextWrangler would be my suggestion), find any <dict> entry that points to services.msn.com in any way and remove all those <dict>...</dict> entries, it should resolve the issue. Warning though - I had to delete hundreds of entries so it took a while to do. Once I finished it though, my wife's e-mail has been working fine.

Anyone else having battery life issues after installing Lion?

Anyone else having battery life issues after installing Lion?

Blue Sun Wing wrote:
I have 7.1
I think I would like to uninstall Lion as well. I'd rather have my battery life back.
See if this is helpful: http://www.iphone-my.com/mac/downgrading-lion-snow-leopard/

Hard drive issues after update 10.10.3

Question also posted here:Hard Drive Issues (Both new and old)
I'm trapped in a HDD nightmare with my MacBook Pro mid-2012.
I updated to Yosemite 10.10.3 (with the Photos app). A couple of days after the update, I was watching a movie on my TV screen via HDMI. In the middle of the movie I removed the HDMI cable from the MacBook Pro and everything freezes. I forced shut down (Note: My HDD was encrypted). After I forced shut down, I tried to turn on and the loading screen would never stop loading - like, 14 hours stuck with the progress bar. Since I have backups, I decided to access DU and format my HDD. I tried everything. For real. Every command line I could type on Terminal to format, repair, erase and/or partition. I read almost every issue-related questions on the forums and stack exchange groups for a week (even posted my issue here: http://apple.stackexchange.com/questions/181090/erasing-and-partitioning-hard-dr ive-from-internet-recovery?noredirect=1#comment215695_181090).
So, I decided that it was a HDD failure and bought a new one.
I bought the Seagate 1TB SSHD Hybrid - ST1000LM014. Installed the new fresh disk and guess what? All those same problems again. I´m not able to restore from Time Machine because it doesn't recognize the disk in the restore page. But the disk is recognized in the DU. When I try to erase or partition the new SSHD, the same old errors: File system formatter failed. Yes, I tired GUID Partition Table, all of the security options, etc.
Please. Any light that you can throw at this issue, I'll be very grateful for. BTW, the new SSHD is recognized and the SMART Status says: Verified.
Any ideas on *** is going on?
Thanks in advance!
MacBook Pro (13-inch Mid 2012), i7, 8GB RAM

After I erase the hard drive (I assume one pass of writing zeros is good enough, 7 passes not needed?) do I turn off the laptop, then turn on and insert the Install Disk? Will there be a prompt telling me when to put in the disk? Or do I put in the disc right after erasing?
One pass is fine. If you've previously backed up your hard drive to an external hard drive using SuperDuper!, which is what I use and recommend, or another program, if it created a bootable drive, you want to boot off of it, bring up SuperDuper! and copy the drive back to the internal hard drive. SuperDuper also makes the drive bootable. When done, reboot, and you should be all set. If you're using Time Machine, you'll want to install the operating system, then restore the Time Machine backup. SuperDuper! is available from http://www.shirt-pocket.com/superduper/superduperdescription.html
Finally- should I update the OS? Is there a problem with the newest update that caused this crash, or was it just a spurious glitch/bad luck?
I've been running 10.5.8 for awhile with no issues, and would recommend moving to it.

Hard drives damaged after installing Snow Leopard :(

After installing Snow Leopard all software seemed to work fine. Then I found out that e-sata doesn't seem to work well with Snow.
I've tried two different e-sata cards, including CalDigit's FASTA-2e, which CalDigit claims works fine with 10.6.
My external enclosure appeared and immediately gave me a kernel panic. I tried several times with different working drives and now they are all heavily damaged. Kernal panic after kernal panic, I am noe having a difficult time accessing the data.
Now here's the strange part...after going back to Leopard 10.5, my internal drives all seemed to be infected as well. After using Disk Warrior and apple's disc utility, I got those working ok.
What could be going wrong here? I installed Snow. It was fast. But it wasn't worth it...at least not yet.
If there's anything else I might be doing wrong or any way to fix these drives now, please let me know.
Thanks all!

It seems that Sonnet is not yet compatible with Snow Leopard either. That issue was covered here: http://discussions.apple.com/thread.jspa?threadID=2114442&tstart=0.
Anyone know if RocketRAID eSATA for Mac works with Snow? Apple sells it...
http://store.apple.com/us/product/TW106LL/A?mco=NzE2OTU5Nw
Thanks!

Facetime issue - after installing a new logic board due to liquid damage.

I installed a new logic board this week.. after installing the os x operation system and then upgrading it to mavericks and i used migration assistant to load my backuped user from an external disk.
I tried to log in using my apple id ( which is verified) it couldn't log in beacuse "could not sign in. please check your network connection and try again"
and i did all the updates of mavericks. i tried also before installing mavericks i thougt upgrading will fix it..
i saw on forums that i should add 2 DNS's (8888 and 8844) didn't work.
i tried connection to my phones hotspot - didn't work.
i also went to the firewall thing to allow it recieve cennections..
pleassee help!!
is there a way to reinstall the facetime or something?!?!?!

My problem solved could possiblly be your solution: Check to make sure your system serial number is being read by your logic baord. If the tech forgot to reenter the serial number, it's a known issue for Facetime and Messages (apparantly not know enough yet though, no tech bulliten exists on the topic).
I spent several days trouble shooting my inablility to login to my account with Facetime or Messages (other cloud services worked) after upgrading to Mavericks. I went as far as doing a clean install on my hard drive after spending two hours with a baffled mac tech in a retail store and many hours searching the message boards.
I have never had a logic board (or hard drive) replaced on my Macbook Air, but somehow after the Mavericks update the logic board stopped reading the serial number on my system. It took a call to Apple and a ticket opened to engineering to figure this out (after I uploaded log files).
They were puzzled I experienced this without a logic board replacement, but it was indeed the root cause of the facetime and messages apps failing to log in, and said they'd run in to it recently more than once.
Wish I knew how to post this unbiquitously across all the boards for folks to troubleshoot by simply looking at their system info in the Apple menu; Apple scheduled an appointment for me at an Apple genius bar and it was fixed in fifteen minutes.

Serious external drive problems after installing Mavericks

OK, so now I am seeing multiple external drive problems. Here is my setup: A GTech 4TB drive connected to MacBook Pro via Firewire, formatted of 2 partitions of 2TB each (called GT1 and GT2). This is then daisy chained to two WD drives of 2TB each, called WD1 and WD2.
After installing Mavericks everything worked fine (in fact I have an amazing speed increase). However, after restarting my machine this morning I have the following issues:
The GTech is now a single partition called MyBook (obviously a hangover from the WD drives. I suspect the WD drive managment software) with NO data files. Interestingly it shows the following USED 1,106,870,272 bytes (1.11 GB on disk). This suggests that one of the partitions has disapeared completely.
Whilst WD 1 launces ok, WD 2 causes the Finder to relaunch whenever selected, meaning I can't get to the files. I remember having this problem before when I upgraded to SL, and it having something to do with hidden files that needed to be deleted via the terminal. However, I have searched the web and can't find the solution again.
Given that WD 1 and 2 are my backups of GT 1 and 2, then I now have a situation where I cannot access my primary or backup files for GT 2. Very impressive - not!
Can anbody remember the hidden file solution for the finder relaunch?
Can anybody help me get back my GT1 and 2 partitions (as they have the latest work on them)?

FIrewire & Thunder bolt drives are having issues with Mavericks, avoid same until a fix is issued if you can.
many are reporting same, there is a firewire fault and TB HD on external HD from LaCie (Seagate) and from WD especially.
Technicians are looking into it.
Until there is resolution, consider setting up a USB ext. Time machine HD.
Until then consider confining Mavericks use with USB HD.
Ive tested a very long line of USB HD on Mavericks, all seem fine.
Recommend anyone DO NOT ATTACH any WD MyBook externals (firewire, thunderbolt or otherwise).
I dont have same to test, so I dont know if the problem is in the firmware on the SATA bridge or if its a problem with the WD software

Lenovo driver issues after upgrade to Windows 10

Hi, i recently upgraded my Y50 to windows 10 after i got the notification. Now the Fn+F6 to disable the trackpad and Fn+F5 for airplane mode don't work. others seem to be working properly. I was unable to find any rivers. Also, i noticed that league of legends now runs at 60fps when uncapped, while previously it ran at about 180. I am not sure if the nvidia graphics card is being detected or if it is using the intel one.

the problem has been fixed by 1- reinstalled win 10 2- win 10 removed intel hd 5500 driver as expected , but i didnt update it manually nor by update from device manager nor make any changes , so i ran windows 10 update tool from system and made all 100% update after restart things are ok now every thing is ok and new intel hd 5500 driver has been installed by win 10 update tool : 10.18.15.4248 //driver date : 29/06/2015 also invidia 840m driver has been updated thanx for any try to help and if any one still stuck with black screen the problem is that win 10 read two monitors instead of 1 so you have to click "windows button + P while black screen already on " and try to hit and click on first choise or other choises till you can see the desktop , sure u cant see any thing while u are trying to choose but you should try or may be you connect another monitor or tv and fix this issue by win button + P good luck

Cd burning issue after installing and updating snow leopard

After installing and updating snow leapard to the latest version, the cd burner for i-tunes quit working. it says" burning disk initializing" then "burning disk finishing" comes up with the error "the attempt to burn a disk failed. the disc drive didn't respond properly and can't recover or retry. Any suggestions to fix this problem?

First try other disks, brand new, then try another brand, then consider backup user files and (clean and polish then) c booting off the 10.6.3 disk and simply reinstalling OS X then updating to 10.6.8 again.
Hopefully this should fix the issue in OS X software, you may have to reinstall certain third party software again that it's kext files got kicked out of OS X by the reinstall.
If you get hung booting at any time, simply hold the shift key down and then update your software then reboot normally

Issues after installing Hotfix Rollup 5 for SP3

Hi,
Last weekend we installed Hotfix Rollup Pack 5 for SP3 on our (single) Exchange 2010 Enterprise server.
This was needed to fix the WebApp Light issue with IE11 and to fix the problem where users were unsable to delete mails sent from multifunctionals.
These 2 issues were fixed by installing the hotfix rollup pack, but now our users have different problems...
Some users (not all of them, haven't found a common denominator yet) report that they don't see new mails in their Outlook 2010 box, even though they got the envelope notifier.
When they change folder and back to the Inbox the new mail is suddenly visible.
Same sort of "delay" happens when users mark a message for follow-up or try to change a message from unread to read.
Some users also report that they see delegated mailboxes (mailboxes from other users that they have full mailbox access to) twice in their Outlook 2010.
Outlook 2010 is running in online mode (because it's running on terminal/citrix servers), so it's no issue with caching as far as I understand.
I've already checked if there are any updates for Outlook available, but we've installed them all already.
I though I'd found something:
Noticed a lot of errors in the application log on the Exchange Server which pointed me to this:
http://theintegrity.co.uk/2010/08/mapi-session-exceeded-the-maximum-of-500-objects-of-type-objtfolder/
I've added the registry values now with a value of 1500, but unfortunately this didn't help.
The errors in the eventlog are gone, but even after restarting the IS some users still have these problems.
One user reported that it takes about 7 minutes for a read mail to actually switch to "read" when looking at his inbox.
Did anyone else notice these problems? And maybe have a fix for them?
I really don't want to roll back the update :(
I even rebooted the Exchange Server after installing the rollup even though that wasn't even necessary
Thanks in advance!
Regards,
Jeroen

Correct - http://support.microsoft.com/kb/2925273 discusses this issue.
If you do raise a support case to request this, please ensure that you review and understand the requirements for IU installation and removal.
For example:   You *MUST* manually remove it prior to installing Exchange 2010 SP3 RU6.
Cheers,
Rhoderick
Microsoft Senior Exchange PFE
Blog:
http://blogs.technet.com/rmilne
Twitter:   LinkedIn:
  Facebook:
  XING:
Note: Posts are provided “AS IS” without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and/or fitness for a particular purpose.

CD Driver Issues after installing 11.1.4

Similar Messages

Maybe you are looking for