CD/DVD drive of Satellite A30 does not work properly

I have a satellite A30 - 921, but for some reason the cd/dvd has stopped working. In Drivers folder it says "driver corrupt/missing. (Error code 39). It will not roll-back or update either. Do i need to download the driver ( it is Toshiba dvd-rom SD-R6112) again & if so how/where? I cant use the recovery or installation disc as it wont read the drive. Any ideas pls.

So, you want to tell that your CD/DVD-drive is defective and you cannot read from it nor recover your system.
To download drivers you should take a look here:
http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp
Otherwise I suggest you to bring your machine to an authorized service partner for a hardwarecheckup. If your drive is really defective then it should be replaced.
If you need some help to find a service partner, then click on this link to find the nearest available ASP in your country:
http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT
Greets

Similar Messages

  • DVD-Rom drive in Satellite C655-S5128 not working properly in Windows 8

    I recently upgraded my system from Windows 7 to Windows 8. However, the DVD-Rom drive after the upgrade no longer works properly -- it now treats the pre-recorded disk as if it was completely blank. I tried reinstalling the Toshiba Disc Creator, but that did not work.
    Any solution?

    You apparently did not use the Toshiba Upgrade Assistant in upgrading to Windows 8.  See HERE for DVD and Disk Creator problems occurring during the upgrade and solutions.
    C.B.
    Toshiba Sat. C75D-B7260 Win 8.1 64 Bit--Toshiba Sat. L775D-S7132 Win 7 HP SP1 64 Bit and Win 10 PRO Technical Preview--Toshiba Sat. L305-S5921 Win Vista SP2 32 Bit

  • Toshiba DVD Player on Satellite U300 does not work

    I have a new Sat U300 and the Toshiba DVD player refuses to work a, the message is that a module is missing.
    Any ideas?

    Hi,
    wheres the problem. Uninstall the current installed version and reinstall the Toshiba HD-DVD player. It would be the best if you look at the [Toshiba Driver Download Site|http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp] for updates of this program.
    If this does not help, backup all your files and perform a full system recovery, which should really help.
    Otherwise, give some feedback here.
    bye

  • CD/DVD drive on Satellite Pro M70 wont work properly

    Following my up date to Vista Ultimate and SP1 my CD/DVD disk drive stopped working.
    I was able to adjuest this using the "HKEY_LOCAL_MACHINE/SYSTEM/ETC/.." but now only DVD will operate correctly.
    When I try to re-install my All-in One printer the installation only reaches step 1 and I then get the follwing message. 'the Installer cannot access the regristry key - HIKEY_LOCAL_MACHINE\SYSTEM\Current\ControlSEt\Enum .'
    The drive sems to be permanently in DVD RW. Can anyone assist.

    >Can anyone assist?
    Maybe Microsoft. Many different and very strange issues occur after SP1 installation. For better overview check http://aps2.toshiba-tro.de/kb0/TSB84026M0000R01.htm

  • Since installing Lion, I have not been able to utilize Time Machine (does not recognize the back-up drive); my wireless mouse does not function properly; I have experienced unreasonable delays in the system.  Is there a fix or upgrade coming?

    Is there a fix or upgrade to deal with the many problems I am experiencing since I installed Lion?  I can no longer utilize Time Machine (Does not see the back-up drive); my wireless mouse does not work properly; my iMac has slowed down considerably.  I am reminded of having a PC machine again.  Bummer!

    Either downgrade to Snow Leopard or try reinstalling Lion.
    Reinstalling Lion Without the Installer
    Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alterhatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
    Reinstall Lion: Select Reinstall Lion and click on the Continue button.
    Note: You can also re-download the Lion installer by opening the App Store application. Hold down the OPTION key and click on the Purchases icon in the toolbar. You should now see an active Install button to the right of your Lion purchase entry. There are situations in which this will not work. For example, if you are already booted into the Lion you originally purchased with your Apple ID or if an instance of the Lion installer is located anywhere on your computer.
    Downgrade Lion to Snow Leopard
    1.  Boot from your Snow Leopard Installer Disc. After the installer loads select your language and click on the Continue button.  When the menu bar appears select Disk Utility from the Utilities menu.
    2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area.  If it does not say "Verified" then the drive is failing or has failed and will need replacing.  SMART info will not be reported  on external drives. Otherwise, click on the Partition tab in the DU main window.
    3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID then click on the OK button. Click on the Partition button and wait until the process has completed.
    4. Quit DU and return to the installer. Install Snow Leopard.
    This will erase the whole drive so be sure to backup your files if you don't have a backup already. If you have performed a TM backup using Lion be aware that you cannot restore from that backup in Snow Leopard (see below.) I suggest you make a separate backup using Carbon Copy Cloner 3.4.1.
    If you have Snow Leopard Time Machine backups, do a full system restore per #14 in Time Machine - Frequently Asked Questions.  If you have subsequent backups from Lion, you can restore newer items selectively, via the "Star Wars" display, per #15 there, but be careful; some Snow Leopard apps may not work with the Lion files.

  • Satellite A30 - CD-ROM does not work properly

    My CD ROM does not work properly because of corrupted drivers. I have tried uninstalling etc. How do you load new drivers or even reformat from the recovery disc when the CD ROM drive won't work?
    Seems like catch 22. Anyone help?

    If it is really a problem with the drivers for your CD-Rom, you can recover it.
    Because you need to boot your Notebook with the Recovery CD/DVD.
    This has nothing to do with missing drivers in the Windows Operating System.
    And if you can not boot with the Recovery Disc, I would say your Disc drive is broken.

  • My dvd slot for imac10,1 does not work. It rejects the disc. Problem after reinstall of backup from hdd.

    My dvd slot for imac10,1 does not work. I had a new harddrive installed in November and the MacStore installed my backups from an external harddrive. I do not use it other than to upload programs, so I have not tried using it until tax season, but it rejects the disc. The ata file indicates no dvd firmware, but the serial-ata does indicate firmware for a dvdrw. What might I do about this to bring the dvd back, least expensive to most?

    Yesterday I started having the same problem. Can read disc (play movies and music) but blank disk are ejected or idvd cannot see the blank disk. I have a almost 12 month old 27" i7 imac.

  • My Iphoto does not work properly, after downloading Mavericks.  How can I fix it ?  loading Mavericks

    My Iphoto does not work properly after downloading Maverick. How can I fix it ?

    With the amount of information you've provided it's impossible to offer a potential solution.  We can't see your computer so we need to know the details of your problem and setup, i.e.:
    what version of iPhoto are you using?
    what system version are you running?
    what do you mean by not working properly? Explain in detail.
    what fixes have you tried?
    where is your library located?
    did you apply any updates or upgrades just prior to the problem occurring?
    are you running a "managed" or "referenced" library?
    what type of Mac?
    how much free space on your boot drive?
    OT

  • Accidentally removed from,sharing and permissions the admin user,and now i do not when i find the home icon at my computer i do not have permmission,and the mac does not works properly,lots of question mark at the dock ,please help

    accidentally removed from,sharing and permissions the admin user,and now i do not when i find the home icon at my computer i do not have permmission,and the mac does not works properly,lots of question mark at the dock ,please help

    I'm going to assume that since you deleted your hard drive and all its files, you had a backup, yes? If the backup has an OS (bootable clone), then you can boot into it by holding down the option key when you start up you iMac and choose the backup drive. Then use Carbon Copy Cloner or Super Duper to copy the files back to your iMac.

  • TS1702 When I update to IOS6 on my 4S Facebook does not work properly, the news feed never updates it only says no new storeys and shows a picture of an antenna. When I reset my phone and go back to IOS5 Facebook works fine. What's up with IOS6 ????

    When I update my iPhone 4S to iOS six Facebook does not work properly the newsfeed doesn't load properly and I can never see what's going on all I see is a picture of an antenna and a little thing underneath it says no new stories when I reset my phone back to iOS 5 then it works just fine and I don't have any issues so there must be something wrong with iOS six that isn't letting Facebook load properly

    No I did not use any unauthorized methods for anything, I simply reset my phone back to factory.
    <Edited By Host>

  • Adobe Creative Cloud (Desktop) does not work properly. The application is blocked : it could not be launch neither stopped. I'm on MAC Yosemite OS, does anyone know how to remove it properly or to force its stop. It does not appear in the launched applica

    Adobe Creative Cloud (Desktop) does not work properly. The application is blocked : it could not be launch neither stopped. I'm on MAC Yosemite OS, does anyone know how to remove it properly or to force its stop. It does not appear in the launched applications.

    I received no error message. The application was just trying to find applications unsuccessfully.
    I am using MAC OS 10.10.1
    I tried to uninstall the application  but it seems that a kind of deamon is still installed thus providing me to reinstall properly. Do you know where are the elements to remove in order to get my machine just like before ?
    Otherwise I would have to reinstall everything and this would be a pain.
    Thanks for your help.

  • Flash player does not work properly on Windows 7 32 bits

    Hello,
    My flash player does not work properly on Windows 7 32 bits with Firfox and IE8 (lasts versions).
    My Flash player version : 10.0.45.2, but I tried with version 9 too, with same problems.
    I have tried to uninstall, reboot, reinstall several times, ... witch did not worked.
    In fact, it works correctly on some sites, like youtube, but not on some others like :
    http://www.dailymotion.com/ => black screen instead of videos, right click gives flash context menu
    http://www.canalplus.fr/ => videos does not load, right click gives flash context menu
    http://www.myspace.com/ => no audio player, right click gives flash context menu
    some games in http://www.kongregate.com/ => black screen instead of games, right click gives flash context menu
    I have no problem with shockwave in http://www.adobe.com/shockwave/welcome/
    No problem too with flash player on http://www.adobe.com/software/flash/about/
    But in the Global Privacy Settings panel (http://www.macromedia.com/support/documentation/en/flashplayer/help/settings_manager02.htm l), I cannot change any settings :
    I cannot check boxes,
    My changes are not saved.
    In most of flash animations, videos, ...,
    when I click on parameters, I cannot do anything, even closing.
    when I am in full screen mode, the message "press escape to exit...." does not disappear.
    Last thing, all those problems was not there when I was on Windows XP, few weeks ago, and appear with my registered Windows 7 premium familly edition, with the same hardware configuration...
    Thank you for your help

    Hi eidnolb
    Thanks for your answer.
    This is what I have :
    Verify user permissions
    I have an administrator account.
    I tried (uninstall, install and run) with super-administrator account for same results
    Install the most current version.
    I am running the latest version (10.0.45.2)
    Run the Clean Installer to Fix 3rd Party Flash Player Cleaners
    I did not "clean" my computer.
    Troubleshoot Pop-up blockers
    I have no Pop-up or esle blocker  software.
    Ensure that Internet utilities do not block Flash Player
    I tried (uninstall, install and run) without Avast.
    I have windows 7 firewall. I do not know where I can allow ActiveX  controls and Flash (SWF) content. I do not see anything relative to ActiveX an Flash in allowed program list.
    Fix machine crashes when displaying Flash content
    I have no freez or crash.
    Using IE, Shockwave Flash Object is Enabled and vs 10.0.45.2
    Using FF, I have SWF vs  10.0.45.2 and it is Enabled
    I really do not understand !!
    Thanks,
    Ju'

  • Image display control scrolling does not work properly when zoomed in

    I am using a ROI on an image in the image display control. When zooming into the image to fine-adjust the positioning of the ROI, the image scrolling does not work properly. As far as I understand, the image should scroll automatically when the ROI is leaving the visible area. However, the scrolling behaviour seems to depend on the origin of the Labview panel, not the origin of the image display control, which might require to move the ROI way out of the visible area before the scrolling takes place. In other words: the coordinate system of the image display control is shifted with respect to the true visible image area, depending on where you place it on the front panel. As a consequence, when clicking on a ROI which is in the visible area, but is outside of what Labview thinks is the visible area, it might immediately jump to the left border of the image, making the positioning of the ROI really difficult.
    Has anyone noticed this behaviour, and what would be a reliable solution to avoid this? 
    Dirk

    Hello,
    no, I am not talking about the tools palette. Just place an image control with some image in it on a new VI front panel. Then, use the rectangle from the tools and select a ROI in the image. If you zoom in (using the magnification glass), and then grab the ROI and move it around, the image scroll with the ROI. So far, so good. If you now place the image control elsewhere on the panel, or add new control above it, resize the panel, etc. , this scrolling when moving the ROI will not work correctly if the origin (0,0) of the panel is far away from the image control.
    I have attached a VI for simplicity (although there is hardly any code in it).
    If you make a ROI and try to move it down, you will notice that scrolling starts if you move the mouse out to about 10cms below the image (depens on your screen, of course). After that, if you click on the ROI, the scroll bars and ROI might jump up to the upper end of the image. Imagine how annoying this is if you try to finely adjust the ROI position. 
    I think it is a bug in the implementation of the image display control.
    Thanks,
    Dirk
    Attachments:
    scrolling.vi ‏818 KB

  • Subvi does not work properly when called inside a vi

    Hello Every body
    thanks for your help. i am using a sub vi for sine signal generation. as a vi it works fine. but when i called this subvi inside another VI it gives some problems. for example timer indicator works properly.it reinitializes as well in the sub vi, but in the main VI it does not work properly. means does not count the time.in the sub vi on the fly i can change the values of frequency and amplitude in real time, but when i use as sub vi, it does not reponse as i change the values in the control arrays.similarly pause and continue works properly in the sub vi, but once again in the main VI, it does not work properly.graph indicator also work properly in the sub vi. but here once again it does not work properly in the main VI.the pause resume indicator also does not blink, when it is continue. in the subvi it blinks very well.generally why the sub vi does not work properly inside the VI?i am sending my VI and sub vis.
    any tips would be highly appreciated.
    thanks
    Regards
    Attachments:
    vi.zip ‏87 KB

    I just want to add some more details to Dan's answer. The subVI is acting exactly like you've coded it. The mistake is in understanding how subVIs work. When you call a subVI (or a function in any other language), you pass some parameters to it, the subVI does it's thing and returns values. the subVI does not accept new parameters from the calling VI until it returns to the caller and the caller runs the subVI again. In your case, you have a subVI with a while loop. You have some front panel control wired to the subVI's stop terminal. When first called, the value is false. So the subVI will keep running until the subVI's stop button becomes true but you cannot change it from main until the subVI finishes and returns so the subVI will never stop. As Dan says, the solution is pass references of front panel controls to the subVI and have the subVI monitor those references for changes and to update references to indicators on Main. You subVI does not need any front panel controls or indicators of it's own.

  • My Mac App Store on my MacBook Pro does not work properly.

    My Mac App Store on my MacBook Pro 15 inch does not work properly. When i go on to the app store, my wi-fi resets and then my app store quits. Why is this? How can i fix this problem? Please Help

    Back up all your files, on boot up when you first press the power button, press CMd and r and keep pressing until you get something apart from a apple logo. Then click reinstall Mac OS X or something like that. You may be prompted to insert your disk.
    Good luck

Maybe you are looking for