CE-565 CPU UTILISATION 100% DUE TO SPAM TRAFFIC
HI,
I have a ce-565 conifured as a proxy .
it was working fine till recently when due to spam in the network , the cpu utilisation reached 100%
and i had to remove the cache engine.
now whenever i put the cache engine, the network becomes slow.
WIll it become ok if i do a clear cache or do i need to re-format the hard-disks again.Pls suggest.It"s very urgent.
Thanks in advance,
Regards,
Amit.
Amit,
I don't think clearing the cache will have an effect on that... but you can try it since it does not have nay harm other than erasing cached data.
Make sure that you do not allow access to the cache from the Internet, so only your internal clients can access it. Also, you can configure some sort of authentication (Such as NTLM or LDAP) on the cache.
If those are not options, or do not resolve the issue, then you should open a case up with Cisco TAC.
Hope this helps..
-Steve
Similar Messages
-
Weblogic reaches 100% CPU utilisation
I am using WebLogic Server Version 10.3.1.0. I got an application deployed in this server, which is developed with java1.6, ejb, hibernate. I start the server with 8GB of RAM assigned to it and after a day or two the weblogic server causes the use of the CPU to reach to 100% and as a result the server sort of doesn't response anymore. I will be creating 30-40 thread per managed server and one server has two managed server. The volume will be around 30k per day. I dont know which is causing the 100% cpu utilisation and here below are the thread dumps which have taken at the time of high cpu in a server. Please let me know where is the exact issue and where is the stuck thread (if any)? In which part the issue is occuring?
10774:
===== FULL THREAD DUMP ===============
Thu Jun 19 16:57:39 2014
Oracle JRockit(R) R28.2.8-10-156881-1.6.0_51-20130611-1146-linux-x86_64
"Main Thread" id=1 idx=0x4 tid=10776 prio=5 alive, waiting, native_blocked
-- Waiting for notification on: weblogic/t3/srvr/T3Srvr@0xa4db4c58[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/t3/srvr/T3Srvr.waitForDeath(T3Srvr.java:981)
^-- Lock released while waiting: weblogic/t3/srvr/T3Srvr@0xa4db4c58[fat lock]
at weblogic/t3/srvr/T3Srvr.run(T3Srvr.java:490)
at weblogic/Server.main(Server.java:71)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"(Signal Handler)" id=2 idx=0x8 tid=10777 prio=5 alive, native_blocked, daemon
"(OC Main Thread)" id=3 idx=0xc tid=10778 prio=5 alive, native_waiting, daemon
"(GC Worker Thread 1)" id=? idx=0x10 tid=10779 prio=5 alive, daemon
"(GC Worker Thread 2)" id=? idx=0x14 tid=10780 prio=5 alive, daemon
"(GC Worker Thread 3)" id=? idx=0x18 tid=10781 prio=5 alive, daemon
"(GC Worker Thread 4)" id=? idx=0x1c tid=10782 prio=5 alive, daemon
"(Code Generation Thread 1)" id=4 idx=0x20 tid=10783 prio=5 alive, native_waiting, daemon
"(Code Optimization Thread 1)" id=5 idx=0x24 tid=10784 prio=5 alive, native_waiting, daemon
"(VM Periodic Task)" id=6 idx=0x28 tid=10785 prio=10 alive, native_waiting, daemon
"Finalizer" id=7 idx=0x2c tid=10786 prio=8 alive, native_waiting, daemon
at jrockit/memory/Finalizer.waitForFinalizees(J[Ljava/lang/Object;)I(Native Method)
at jrockit/memory/Finalizer.access$700(Finalizer.java:12)
at jrockit/memory/Finalizer$4.run(Finalizer.java:201)
at java/lang/Thread.run(Thread.java:662)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"Reference Handler" id=8 idx=0x30 tid=10787 prio=10 alive, native_waiting, daemon
at java/lang/ref/Reference.waitForActivatedQueue(J)Ljava/lang/ref/Reference;(Native Method)
at java/lang/ref/Reference.access$100(Reference.java:11)
at java/lang/ref/Reference$ReferenceHandler.run(Reference.java:82)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"(Sensor Event Thread)" id=9 idx=0x34 tid=10788 prio=5 alive, native_blocked, daemon
"VM JFR Buffer Thread" id=10 idx=0x38 tid=10789 prio=5 alive, in native, daemon
"Timer-0" id=13 idx=0x3c tid=10793 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: java/util/TaskQueue@0xa4d5d260[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[optimized]
at java/util/TimerThread.mainLoop(Timer.java:483)
^-- Lock released while waiting: java/util/TaskQueue@0xa4d5d260[fat lock]
at java/util/TimerThread.run(Timer.java:462)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '0' for queue: 'default'" id=14 idx=0x40 tid=10839 prio=5 alive, native_blocked, daemon
at java/util/HashMap.get(HashMap.java:385)[optimized]
at com/appl/vsms/pi/outbound/ControllerCache.getEntry(ControllerCache.java:48)[inlined]
at com/appl/vsms/bean/pi/MessageStatusConsumer.onMessage(MessageStatusConsumer.java:90)[optimized]
at weblogic/ejb/container/internal/MDListener.execute(MDListener.java:574)[inlined]
at weblogic/ejb/container/internal/MDListener.run(MDListener.java:893)[optimized]
at weblogic/work/ExecuteRequestAdapter.execute(ExecuteRequestAdapter.java:21)[optimized]
at weblogic/kernel/ExecuteThread.execute(ExecuteThread.java:145)[optimized]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:117)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '1' for queue: 'default'" id=15 idx=0x44 tid=10840 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: java/util/LinkedList@0xa8cbed08[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/ejb/container/internal/MDListener.getListener(MDListener.java:240)[optimized]
^-- Lock released while waiting: java/util/LinkedList@0xa8cbed08[fat lock]
at weblogic/ejb/container/internal/MDListener.transactionalOnMessage(MDListener.java:480)[inlined]
at weblogic/ejb/container/internal/MDListener.onMessage(MDListener.java:379)[optimized]
at weblogic/jms/client/JMSSession.onMessage(JMSSession.java:4659)[optimized]
at weblogic/jms/client/JMSSession.execute(JMSSession.java:4345)[optimized]
at weblogic/jms/client/JMSSession.executeMessage(JMSSession.java:3821)[optimized]
at weblogic/jms/client/JMSSession.access$000(JMSSession.java:115)
at weblogic/jms/client/JMSSession$UseForRunnable.run(JMSSession.java:5170)
at weblogic/work/ExecuteRequestAdapter.execute(ExecuteRequestAdapter.java:21)[optimized]
at weblogic/kernel/ExecuteThread.execute(ExecuteThread.java:145)[optimized]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:117)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '2' for queue: 'default'" id=16 idx=0x48 tid=10841 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4d5f0d0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4d5f0d0[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '3' for queue: 'default'" id=17 idx=0x4c tid=10842 prio=5 alive, native_blocked, daemon
at java/util/HashMap.get(HashMap.java:385)[optimized]
at com/appl/vsms/pi/outbound/ControllerCache.getEntry(ControllerCache.java:48)[inlined]
at com/appl/vsms/bean/pi/MessageStatusConsumer.onMessage(MessageStatusConsumer.java:90)[optimized]
at weblogic/ejb/container/internal/MDListener.execute(MDListener.java:574)[inlined]
at weblogic/ejb/container/internal/MDListener.run(MDListener.java:893)[optimized]
at weblogic/work/ExecuteRequestAdapter.execute(ExecuteRequestAdapter.java:21)[optimized]
at weblogic/kernel/ExecuteThread.execute(ExecuteThread.java:145)[optimized]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:117)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '4' for queue: 'default'" id=18 idx=0x50 tid=10843 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4d5fe50[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4d5fe50[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '5' for queue: 'default'" id=19 idx=0x54 tid=10844 prio=5 alive, native_blocked, daemon
at java/util/HashMap.get(HashMap.java:385)[optimized]
at com/appl/vsms/pi/outbound/ControllerCache.getEntry(ControllerCache.java:48)[inlined]
at com/appl/vsms/bean/pi/MessageStatusConsumer.onMessage(MessageStatusConsumer.java:90)[optimized]
at weblogic/ejb/container/internal/MDListener.execute(MDListener.java:574)[inlined]
at weblogic/ejb/container/internal/MDListener.run(MDListener.java:893)[optimized]
at weblogic/work/ExecuteRequestAdapter.execute(ExecuteRequestAdapter.java:21)[optimized]
at weblogic/kernel/ExecuteThread.execute(ExecuteThread.java:145)[optimized]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:117)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '6' for queue: 'default'" id=20 idx=0x58 tid=10845 prio=5 alive, native_blocked, daemon
at java/util/HashMap.get(HashMap.java:385)[optimized]
at com/appl/vsms/pi/outbound/ControllerCache.getEntry(ControllerCache.java:48)[inlined]
at com/appl/vsms/bean/pi/MessageStatusConsumer.onMessage(MessageStatusConsumer.java:90)[optimized]
at weblogic/ejb/container/internal/MDListener.execute(MDListener.java:574)[inlined]
at weblogic/ejb/container/internal/MDListener.run(MDListener.java:893)[optimized]
at weblogic/work/ExecuteRequestAdapter.execute(ExecuteRequestAdapter.java:21)[optimized]
at weblogic/kernel/ExecuteThread.execute(ExecuteThread.java:145)[optimized]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:117)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '7' for queue: 'default'" id=21 idx=0x5c tid=10846 prio=5 alive, native_blocked, daemon
at java/util/HashMap.get(HashMap.java:385)[optimized]
at com/appl/vsms/pi/outbound/ControllerCache.getEntry(ControllerCache.java:48)[inlined]
at com/appl/vsms/bean/pi/MessageStatusConsumer.onMessage(MessageStatusConsumer.java:90)[optimized]
at weblogic/ejb/container/internal/MDListener.execute(MDListener.java:574)[inlined]
at weblogic/ejb/container/internal/MDListener.run(MDListener.java:893)[optimized]
at weblogic/work/ExecuteRequestAdapter.execute(ExecuteRequestAdapter.java:21)[optimized]
at weblogic/kernel/ExecuteThread.execute(ExecuteThread.java:145)[optimized]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:117)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '8' for queue: 'default'" id=22 idx=0x60 tid=10847 prio=5 alive, native_blocked, daemon
at java/util/HashMap.get(HashMap.java:385)[optimized]
at com/appl/vsms/pi/outbound/ControllerCache.getEntry(ControllerCache.java:48)[inlined]
at com/appl/vsms/bean/pi/MessageStatusConsumer.onMessage(MessageStatusConsumer.java:90)[optimized]
at weblogic/ejb/container/internal/MDListener.execute(MDListener.java:574)[inlined]
at weblogic/ejb/container/internal/MDListener.run(MDListener.java:893)[optimized]
at weblogic/work/ExecuteRequestAdapter.execute(ExecuteRequestAdapter.java:21)[optimized]
at weblogic/kernel/ExecuteThread.execute(ExecuteThread.java:145)[optimized]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:117)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '9' for queue: 'default'" id=23 idx=0x64 tid=10848 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4d62010[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4d62010[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '10' for queue: 'default'" id=24 idx=0x68 tid=10849 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4d626d0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4d626d0[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '11' for queue: 'default'" id=25 idx=0x6c tid=10850 prio=5 alive, native_blocked, daemon
at java/util/HashMap.get(HashMap.java:385)[optimized]
at com/appl/vsms/pi/outbound/ControllerCache.getEntry(ControllerCache.java:48)[inlined]
at com/appl/vsms/bean/pi/MessageStatusConsumer.onMessage(MessageStatusConsumer.java:90)[optimized]
at weblogic/ejb/container/internal/MDListener.execute(MDListener.java:574)[inlined]
at weblogic/ejb/container/internal/MDListener.run(MDListener.java:893)[optimized]
at weblogic/work/ExecuteRequestAdapter.execute(ExecuteRequestAdapter.java:21)[optimized]
at weblogic/kernel/ExecuteThread.execute(ExecuteThread.java:145)[optimized]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:117)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '12' for queue: 'default'" id=26 idx=0x70 tid=10851 prio=5 alive, native_blocked, daemon
at java/util/HashMap.get(HashMap.java:385)[optimized]
at com/appl/vsms/pi/outbound/ControllerCache.getEntry(ControllerCache.java:48)[inlined]
at com/appl/vsms/bean/pi/MessageStatusConsumer.onMessage(MessageStatusConsumer.java:90)[optimized]
at weblogic/ejb/container/internal/MDListener.execute(MDListener.java:574)[inlined]
at weblogic/ejb/container/internal/MDListener.run(MDListener.java:893)[optimized]
at weblogic/work/ExecuteRequestAdapter.execute(ExecuteRequestAdapter.java:21)[optimized]
at weblogic/kernel/ExecuteThread.execute(ExecuteThread.java:145)[optimized]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:117)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '13' for queue: 'default'" id=27 idx=0x74 tid=10852 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4d648e8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4d648e8[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '14' for queue: 'default'" id=28 idx=0x78 tid=10853 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4d65568[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4d65568[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '0' for queue: 'weblogic.kernel.Non-Blocking'" id=29 idx=0x7c tid=10854 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4d65cc0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4d65cc0[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '1' for queue: 'weblogic.kernel.Non-Blocking'" id=30 idx=0x80 tid=10855 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4d663c0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4d663c0[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '2' for queue: 'weblogic.kernel.Non-Blocking'" id=31 idx=0x84 tid=10856 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4d66ac0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4d66ac0[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '0' for queue: 'weblogic.kernel.System'" id=32 idx=0x88 tid=10857 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4d671c0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4d671c0[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '1' for queue: 'weblogic.kernel.System'" id=33 idx=0x8c tid=10858 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4d67f48[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4d67f48[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '2' for queue: 'weblogic.kernel.System'" id=34 idx=0x90 tid=10859 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4d68cc0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4d68cc0[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '3' for queue: 'weblogic.kernel.System'" id=35 idx=0x94 tid=10860 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4d69a38[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4d69a38[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '4' for queue: 'weblogic.kernel.System'" id=36 idx=0x98 tid=10861 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4d977b8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4d977b8[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '0' for queue: 'weblogic.Rejector'" id=37 idx=0x9c tid=10862 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4d99570[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4d99570[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '1' for queue: 'weblogic.Rejector'" id=38 idx=0xa0 tid=10863 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cf2e38[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cf2e38[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"weblogic.time.TimeEventGenerator" id=39 idx=0xa4 tid=10864 prio=9 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/time/common/internal/TimeTable@0xa4dbed18[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at weblogic/time/common/internal/TimeTable.snooze(TimeTable.java:286)
^-- Lock released while waiting: weblogic/time/common/internal/TimeTable@0xa4dbed18[fat lock]
at weblogic/time/common/internal/TimeEventGenerator.run(TimeEventGenerator.java:117)
at java/lang/Thread.run(Thread.java:662)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"JMAPI event thread" id=40 idx=0xa8 tid=10865 prio=5 alive, in native, daemon
"weblogic.timers.TimerThread" id=41 idx=0xac tid=10866 prio=9 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/timers/internal/TimerThread@0xa4dc3f70[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at weblogic/timers/internal/TimerThread$Thread.run(TimerThread.java:262)
^-- Lock released while waiting: weblogic/timers/internal/TimerThread@0xa4dc3f70[fat lock]
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '0' for queue: 'weblogic.admin.RMI'" id=42 idx=0xb0 tid=10867 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cf3528[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cf3528[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '1' for queue: 'weblogic.admin.RMI'" id=43 idx=0xb4 tid=10868 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cf35f0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cf35f0[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '2' for queue: 'weblogic.admin.RMI'" id=44 idx=0xb8 tid=10869 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cf36b8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cf36b8[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '3' for queue: 'weblogic.admin.RMI'" id=45 idx=0xbc tid=10870 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cf3780[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cf3780[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '4' for queue: 'weblogic.admin.RMI'" id=46 idx=0xc0 tid=10871 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cf3848[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cf3848[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '0' for queue: 'ImageWorkManager'" id=47 idx=0xc4 tid=10896 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cf57e0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cf57e0[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '1' for queue: 'ImageWorkManager'" id=48 idx=0xc8 tid=10899 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cf58a8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cf58a8[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"JFR request timer" id=49 idx=0xcc tid=10900 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: java/util/TaskQueue@0xa4dc69d8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at java/util/TimerThread.mainLoop(Timer.java:483)
^-- Lock released while waiting: java/util/TaskQueue@0xa4dc69d8[fat lock]
at java/util/TimerThread.run(Timer.java:462)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '0' for queue: 'weblogic.logging.DomainLogBroadcasterClient'" id=53 idx=0xd0 tid=10902 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cf6550[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cf6550[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '0' for queue: 'weblogic.logging.LogBroadcaster'" id=54 idx=0xd4 tid=10903 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cf6d50[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cf6d50[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '0' for queue: 'weblogic.socket.Muxer'" id=55 idx=0xd8 tid=10904 prio=5 alive, blocked, native_blocked, daemon
-- Blocked trying to get lock: java/lang/String@0xa4cf78f8[fat lock]
at jrockit/vm/Threads.waitForUnblockSignal()V(Native Method)
at jrockit/vm/Locks.fatLockBlockOrSpin(Locks.java:1411)[optimized]
at jrockit/vm/Locks.lockFat(Locks.java:1512)[optimized]
at jrockit/vm/Locks.monitorEnterSecondStageHard(Locks.java:1054)[optimized]
at jrockit/vm/Locks.monitorEnterSecondStage(Locks.java:1005)[optimized]
at jrockit/vm/Locks.monitorEnter(Locks.java:2179)[optimized]
at weblogic/socket/EPollSocketMuxer.processSockets(EPollSocketMuxer.java:153)
at weblogic/socket/SocketReaderRequest.run(SocketReaderRequest.java:29)
at weblogic/socket/SocketReaderRequest.execute(SocketReaderRequest.java:42)
at weblogic/kernel/ExecuteThread.execute(ExecuteThread.java:145)
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:117)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '1' for queue: 'weblogic.socket.Muxer'" id=56 idx=0xdc tid=10905 prio=5 alive, blocked, native_blocked, daemon
-- Blocked trying to get lock: java/lang/String@0xa4cf78f8[fat lock]
at jrockit/vm/Threads.waitForUnblockSignal()V(Native Method)
at jrockit/vm/Locks.fatLockBlockOrSpin(Locks.java:1411)[optimized]
at jrockit/vm/Locks.lockFat(Locks.java:1512)[optimized]
at jrockit/vm/Locks.monitorEnterSecondStageHard(Locks.java:1054)[optimized]
at jrockit/vm/Locks.monitorEnterSecondStage(Locks.java:1005)[optimized]
at jrockit/vm/Locks.monitorEnter(Locks.java:2179)[optimized]
at weblogic/socket/EPollSocketMuxer.processSockets(EPollSocketMuxer.java:153)
at weblogic/socket/SocketReaderRequest.run(SocketReaderRequest.java:29)
at weblogic/socket/SocketReaderRequest.execute(SocketReaderRequest.java:42)
at weblogic/kernel/ExecuteThread.execute(ExecuteThread.java:145)
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:117)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '2' for queue: 'weblogic.socket.Muxer'" id=57 idx=0xe0 tid=10906 prio=5 alive, blocked, native_blocked, daemon
-- Blocked trying to get lock: java/lang/String@0xa4cf78f8[fat lock]
at jrockit/vm/Threads.waitForUnblockSignal()V(Native Method)
at jrockit/vm/Locks.fatLockBlockOrSpin(Locks.java:1411)[inlined]
at jrockit/vm/Locks.fatLockReacquire(Locks.java:1649)[optimized]
at jrockit/vm/Locks.lockFat(Locks.java:1517)[optimized]
at jrockit/vm/Locks.monitorEnterSecondStageHard(Locks.java:1054)[optimized]
at jrockit/vm/Locks.monitorEnterSecondStage(Locks.java:1005)[optimized]
at jrockit/vm/Locks.monitorEnter(Locks.java:2179)[optimized]
at weblogic/socket/EPollSocketMuxer.processSockets(EPollSocketMuxer.java:153)
at weblogic/socket/SocketReaderRequest.run(SocketReaderRequest.java:29)
at weblogic/socket/SocketReaderRequest.execute(SocketReaderRequest.java:42)
at weblogic/kernel/ExecuteThread.execute(ExecuteThread.java:145)
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:117)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '3' for queue: 'weblogic.socket.Muxer'" id=58 idx=0xe4 tid=10907 prio=5 alive, in native, daemon
at jrockit/ext/epoll/EPoll.epollWait0(ILjava/nio/ByteBuffer;II)I(Native Method)
at jrockit/ext/epoll/EPoll.epollWait(EPoll.java:123)
at weblogic/socket/EPollSocketMuxer.processSockets(EPollSocketMuxer.java:156)
^-- Holding lock: java/lang/String@0xa4cf78f8[fat lock]
at weblogic/socket/SocketReaderRequest.run(SocketReaderRequest.java:29)
at weblogic/socket/SocketReaderRequest.execute(SocketReaderRequest.java:42)
at weblogic/kernel/ExecuteThread.execute(ExecuteThread.java:145)
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:117)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"VDE Transaction Processor Thread" id=61 idx=0xe8 tid=10909 prio=2 alive, waiting, native_blocked, daemon
-- Waiting for notification on: com/octetstring/vde/backend/standard/TransactionProcessor@0xa46c3738[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at com/octetstring/vde/backend/standard/TransactionProcessor.waitChange(TransactionProcessor.java:367)
^-- Lock released while waiting: com/octetstring/vde/backend/standard/TransactionProcessor@0xa46c3738[fat lock]
at com/octetstring/vde/backend/standard/TransactionProcessor.run(TransactionProcessor.java:212)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"DoSManager" id=64 idx=0xf0 tid=10911 prio=6 alive, sleeping, native_waiting, daemon
at java/lang/Thread.sleep(J)V(Native Method)
at com/octetstring/vde/DoSManager.run(DoSManager.java:433)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '0' for queue: 'UserLockout'" id=65 idx=0xf4 tid=10920 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cf93c8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cf93c8[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '1' for queue: 'UserLockout'" id=66 idx=0xf8 tid=10921 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cf9490[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cf9490[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '2' for queue: 'UserLockout'" id=67 idx=0xfc tid=10922 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cf9558[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cf9558[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '3' for queue: 'UserLockout'" id=68 idx=0x100 tid=10923 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cf9620[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cf9620[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '4' for queue: 'UserLockout'" id=69 idx=0x104 tid=10924 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cf96e8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cf96e8[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '0' for queue: 'weblogic.unicast.DispatchWorkManager'" id=70 idx=0x108 tid=10958 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cfbbb0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cfbbb0[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '1' for queue: 'weblogic.unicast.DispatchWorkManager'" id=71 idx=0x10c tid=10959 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cfbc78[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cfbc78[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '2' for queue: 'weblogic.unicast.DispatchWorkManager'" id=72 idx=0x110 tid=10960 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cfbd40[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cfbd40[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '3' for queue: 'weblogic.unicast.DispatchWorkManager'" id=73 idx=0x114 tid=10961 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cfbe08[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cfbe08[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '4' for queue: 'weblogic.unicast.DispatchWorkManager'" id=74 idx=0x118 tid=10962 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4cfbed0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4cfbed0[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '0' for queue: 'weblogic.unicast.ForwardingWorkManager'" id=75 idx=0x11c tid=10963 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c66f40[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c66f40[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '1' for queue: 'weblogic.unicast.ForwardingWorkManager'" id=76 idx=0x120 tid=10964 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c67008[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c67008[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '2' for queue: 'weblogic.unicast.ForwardingWorkManager'" id=77 idx=0x124 tid=10965 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c670d0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c670d0[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '3' for queue: 'weblogic.unicast.ForwardingWorkManager'" id=78 idx=0x128 tid=10966 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c67198[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c67198[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '4' for queue: 'weblogic.unicast.ForwardingWorkManager'" id=79 idx=0x12c tid=10967 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c67260[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c67260[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '0' for queue: 'ClusterMessaging'" id=81 idx=0x134 tid=10969 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c692e0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c692e0[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '0' for queue: 'wl_oldBootStrap'" id=82 idx=0x138 tid=10972 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c69a90[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c69a90[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '1' for queue: 'wl_oldBootStrap'" id=83 idx=0x13c tid=10973 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c69b58[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c69b58[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '2' for queue: 'wl_oldBootStrap'" id=84 idx=0x140 tid=10974 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c69c20[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c69c20[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '3' for queue: 'wl_oldBootStrap'" id=85 idx=0x144 tid=10975 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c69ce8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c69ce8[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '4' for queue: 'wl_oldBootStrap'" id=86 idx=0x148 tid=10980 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c69db0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c69db0[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '5' for queue: 'wl_oldBootStrap'" id=87 idx=0x14c tid=10984 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c69e78[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c69e78[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '6' for queue: 'wl_oldBootStrap'" id=88 idx=0x150 tid=10987 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c69f40[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c69f40[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '7' for queue: 'wl_oldBootStrap'" id=89 idx=0x154 tid=10988 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c6a008[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c6a008[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"Thread-12" id=90 idx=0x158 tid=10989 prio=5 alive, parked, native_blocked
-- Parking to wait for: java/util/concurrent/locks/AbstractQueuedSynchronizer$ConditionObject@0xa4c66b48
at jrockit/vm/Locks.park0(J)V(Native Method)
at jrockit/vm/Locks.park(Locks.java:2230)
at sun/misc/Unsafe.park(ZJ)V(Native Method)
at java/util/concurrent/locks/LockSupport.park(LockSupport.java:156)
at java/util/concurrent/locks/AbstractQueuedSynchronizer$ConditionObject.await(AbstractQueuedSynchronizer.java:1987)
at java/util/concurrent/LinkedBlockingQueue.take(LinkedBlockingQueue.java:399)
at weblogic/utils/concurrent/JDK15ConcurrentBlockingQueue.take(JDK15ConcurrentBlockingQueue.java:89)
at weblogic/store/internal/PersistentStoreImpl.getOutstandingWork(PersistentStoreImpl.java:672)
at weblogic/store/internal/PersistentStoreImpl.run(PersistentStoreImpl.java:721)
at java/lang/Thread.run(Thread.java:662)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '0' for queue: 'JTACoordinatorWM'" id=91 idx=0x15c tid=10990 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c6d128[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c6d128[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '1' for queue: 'JTACoordinatorWM'" id=92 idx=0x160 tid=10991 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c6d1f0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c6d1f0[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '2' for queue: 'JTACoordinatorWM'" id=93 idx=0x164 tid=10992 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c6d2b8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at jrockit/vm/Locks.wait(Locks.java:1973)[inlined]
at java/lang/Object.wait(Object.java:485)[inlined]
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)[optimized]
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c6d2b8[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '0' for queue: 'JmsDispatcher'" id=94 idx=0x168 tid=10995 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c6e688[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c6e688[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '1' for queue: 'JmsDispatcher'" id=95 idx=0x16c tid=10996 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c6e750[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c6e750[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '2' for queue: 'JmsDispatcher'" id=96 idx=0x170 tid=10997 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c6e818[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c6e818[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '3' for queue: 'JmsDispatcher'" id=97 idx=0x174 tid=10998 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c6e8e0[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
at java/lang/Object.wait(J)V(Native Method)
at java/lang/Object.wait(Object.java:485)
at weblogic/kernel/ExecuteThread.waitForRequest(ExecuteThread.java:91)
^-- Lock released while waiting: weblogic/kernel/ServerExecuteThread@0xa4c6e8e0[fat lock]
at weblogic/kernel/ExecuteThread.run(ExecuteThread.java:115)
at jrockit/vm/RNI.c2java(JJJJJ)V(Native Method)
-- end of trace
"ExecuteThread: '4' for queue: 'JmsDispatcher'" id=98 idx=0x178 tid=10999 prio=5 alive, waiting, native_blocked, daemon
-- Waiting for notification on: weblogic/kernel/ServerExecuteThread@0xa4c6e9a8[fat lock]
at jrockit/vm/Threads.waitForNotifySignal(JLjava/lang/Object;)Z(Native Method)
Hi,
Based on the below doc , you can narrow down the actual Thread that is causing this high CPU.
Unexpected High CPU Usage with WebLogic Server (WLS) Support Pattern (Doc ID 779349.1)
Thanks,
Sharmela -
CS6 and AME 100% CPU utilisation
So this is an odd question to ask maybe as we often asked for max CPU utilisation when encoding in the past to get stuff done quicker.
But - this is entirely new behaviour for me at least. I have a 6 core i7 X980 with HT and 24GB ram. In the past, I could queue up several sequences and let them encode to H.264 in the background while i carry on editing. Worked fine with no problems.
I recently upgraded my GPU to a 4GB GTX680 from a 1.2GB GTX570. There have also been 2 updates to PPro as well since I noticed this behaviour.
So the issue is that when encoding, all 12 threads are at 100% CPU utilisation and my mouse control suffers terribly - very very slow mouse as obviously there's not enough CPU resources to drive the pointer properly. This never happened in the past as CPU utilisation was never maxed out like this.
Anyone seen anything similar?
Thanks,
Paul.Hi Darren,
I've not benchmarked the two cards in Premiere - I've not noticed any difference in real world use. Reading a few comparison reviews out there kind of said the same thing too (although gaming based reviews). The reason I went for the 680 was the availability of a 4GB VRAM model which was really important for me in After Effects using complex 3D models in the Video Copilot plugin, Element 3D.
So it was worth it for the memory but maybe not just for Premiere. I don't tend to do a load of video layers at once, the most is maybe a couple of layers PIP on virtual studio type projects but then most of them end up in AE really as its just hugely more flexible and fun to work with -
100% cpu utilisation SQL Dev 1.5 on XP
Using SQL Dev 1.5 prod version on XP on a P4 3ghz with 2gb of ram, SQL Dev executable regularly uses 100% cpu utilisation as reported by task manager.
Also frequently stops responding - no screen redraw and I have to end task.
Until recently I only had 512Mb of ram so put this down to that fact, but with 2gb still getting long 'satellite' delays - particularly with code/param insight.
Anybody else getting this?
taI know I was vahue - apologies, but it's most of the time - literally 99 to 100% cpu utilisation.
e.g.
restart pc, login, give it a couple of mins to settle down. (p4 3ghz, 3gb ram, xp pro, sp1)
start 1.5 sqldev - wait, see the splash screen, look at task manager - memory starts going up, cpu rises rapidly to 99 - 100%
once fully loaded, open 1 connection, open one package body, split screen vertically, so I have sql worksheet and my package body open and visible.
Now sit back and enjoy the vibration coming thru the desktop - the real wooden one - as the pc's fan struggles to cope.
If I leave it for maybe 5 to 10 mins - not doing anything on the pc at all, cpu utilisation will drop significantly.
then do something reckless like edit my package body (not that big ~1500 lines) and hold on to the desk again as we start shaking once more.
great for my typing skills too, as there is no point in looking at the screen to see if I am making mistakes, as it frequently won't display anything until 3 to 5 seconds after I have finished typing
mem usage is up to 250 mb - I have not touched my pc for nearly 10 mins since doing the last edit - still at 99% -
Hi All,
I have installed Oracle Enterprise Linux release 5 as a guest system in Virtual Box running on Windows XP SP2 as the host system. When the virtual machine is running, CPU utilisation of the PC where host OS is installed is 100% with VirtualBox.exe being the process responsible for this.
Could anyone suggest why this is happening and what I can try to resolve this issue?
Thank you.
Kind regards,
DenisNo, the bug was saying that having these things running on the host can use the same mechanisms that VBOX uses and everything gets in each others way.
There are test builds of Google Chromium available for Fedora 11 over at the http://spot.fedorapeople.org/chromium repository. Don't remember if the sources can be found there, but the RPM spec file can, so I guess you could roll your own. -
JVM utilising 100% CPU resources
I have an application deployed to Oracle9iAS application server running on sunE280 with 2 processors and 4 higs ram. I have 1 oc4j process (JVM) serving my application. When there is heavy load on the system CPU utilisation peaks to 100% and the application stops responding. My oc4j processes (JVM) is running with 128m max heap size. So i increased the heap from default setting to min256m and Max512m sizes. I also increased the number of oc4j processes from 1 to 2.
At some point of time, both the oc4j processes utilise 48% of the CPU resouces each and then the application stops hanging. I did a vmstat and iostat on the system and below is o/p
procs memory page disk faults cpu
r b w swap free re mf pi po fr de sr m1 m2 m3 m4 in sy cs us sy id
0 0 0 4516376 2536400 25 76 150 0 0 0 0 0 0 1 0 349 99 1440 7 3 90
16 0 0 3945456 1787720 0 12 16 0 0 0 0 0 0 0 0 544 85221 2399 83 16 0
14 0 0 3945456 1787712 0 15 12 0 0 0 0 0 0 0 0 574 82593 2547 81 18 1
16 0 0 3944856 1787288 54 483 28 0 0 0 0 0 0 16 1 667 93353 2792 76 24 0
15 0 0 3940208 1787088 34 276 16 0 0 0 0 6 0 8 0 667 93823 2736 75 25 0
14 0 0 3945208 1787544 0 11 16 0 0 0 0 0 0 0 0 695 92164 3103 85 15 0
14 0 0 3945248 1787584 0 1 8 0 0 0 0 1 0 14 0 647 96116 2818 83 16 1
14 0 0 3945208 1787544 0 27 0 0 0 0 0 0 0 16 5 689 96923 2718 83 14 3
11 0 0 3945184 1787520 23 229 32 12 12 0 0 0 0 0 0 628 81816 2683 79 21 0
iostat 2 10
tty md1 md2 md3 md4 cpu
tin tout kps tps serv kps tps serv kps tps serv kps tps serv us sy wt id
0 20 3 0 42 0 0 28 4 1 15 2 0 20 7 3 2 88
0 0 0 0 0 0 0 0 0 0 0 0 0 0 83 16 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 81 18 0 1
0 0 0 0 0 0 0 0 8 16 8 0 1 21 76 24 0 0
0 0 48 6 56 0 0 0 4 9 6 0 1 38 75 25 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 85 14 0 0
0 0 1 1 20 0 0 0 65 12 24 0 0 0 82 16 0 1
0 0 0 0 0 0 0 0 41 19 20 18 5 22 83 14 0 3
Can someone provide me any clue as to why the JVM peaks in CPU utilisations and then stops responding?Check Oracle's MetaLink (http:\\metalink.oracle.com) bug number 2218716. There is a problem with OC4J Containers and the FIXED_WAIT_SCHEME when the maximun number of connections is reached.
Just in case you don't have access to it, here is part of the document:
SUGGESTED FIX: Introduce a new cache property, CacheFixedWaitSleepTime, on OCCImpl (with setter/getter methods). In the while loop that yields when MAX+1 connection is requested, simply sleep for the number of milliseconds.
WORKAROUND: Use other cache schemes, (1) DYNAMIC_SCHEME (2) FIXED_RETURN_NULL_SCHEME
Hope the helps ... -
100% CPU Utilisation while reading from socket
I have writted a ServerSocket program to read data from ethernet client bridge. client-bridge is a system which converts serial data to TCP packet and vice versa. I can read from the client bridge only through creating a server socket and waiting for the client bridge to make a client socket connection (ServerSocket.accept() method.
The problem that I m facing is that, the client bridge is creating connection only once. I have created an infinite loop which keeps on reading from the socket. The performance of the application goes down drastically (100% CPU utilisation through task manager) when this application is run. Is there a better way of reading data from the client bridge. The client bridge is not in our control and the server can only wait for the client to make connection.
Please help. Thanking you all in anticipation.
Regards,
AmitabhaIf I close the client socket will the client create a new socket to
transmit data or it depends on the client application.
I have also tried creating a new socket connection for
reading each frame of the protocol. but the client
creates only one socket. What might be the problem?I bet it depends on the client app because your server app only waits for a connection from the client. So it's the client that initiates the connection. When you disconnect the client socket then you will have to wait for another client request. what you can do is to stay connected (unless of course client disconnects itself) and just keep on reading from the client socket. -
CPU utilisation is at 100% on SQL Server
Currently the CPU utilisation is at 100 % on the SQL Server and sql server.exe is utilising 98% in the task manager.Is this because of the query running for long time?
however I dont see any process in running state.
ThanksHi check WITH DB_CPU_Stats
AS
(SELECT DatabaseID, DB_Name(DatabaseID) AS [DatabaseName], SUM(total_worker_time) AS [CPU_Time_Ms]
FROM sys.dm_exec_query_stats AS qs
CROSS APPLY (SELECT CONVERT(int, value) AS [DatabaseID]
FROM sys.dm_exec_plan_attributes(qs.plan_handle)
WHERE attribute = N'dbid')
AS F_DB
GROUP BY DatabaseID)
SELECT ROW_NUMBER() OVER(ORDER BY [CPU_Time_Ms] DESC) AS [row_num],
DatabaseName, [CPU_Time_Ms],
CAST([CPU_Time_Ms] * 1.0 / SUM([CPU_Time_Ms]) OVER() * 100.0 AS DECIMAL(5,
2)) AS [CPUPercent]
FROM DB_CPU_Stats
WHERE DatabaseID > 4 -- system databases
AND DatabaseID <> 32767 -- ResourceDB
ORDER BY row_num OPTION (RECOMPILE);
check error log and trun on traceflag 1222,1204 and see errorlog.
check missing index.
update statistics. -
Windows 7 Gadgets slow to respond, 50% CPU utilisation with gadgets that "move"
I have a fresh installation of Windows 7 RC and everything was fine. I have no idea what may have caused this, but on day 2 of using Windows 7 RC, any desktop gadgets that move (like the CPU meter or the clock with its second hand enabled) cause the sidebar.exe process to go to 50% CPU utilisation (which is 100% of one core on my dual core CPU).
These gadgets then just become unresponsive and I have to close them. I can only keep the Weather gadget on because it doesn't have any animations. I have all Windows updates and the latest NVIDIA driver from Windows Update and even their own website doesn't help. There is something wrong with my gadgets. I have never installed any extra gadgets.
What could it be?Same issue, but after Vista x64 Home Prem upgrade to Win7 Home Prem x64. ATI Radeon HD 4850 graphics card, Quad Core & can't even change the settings of the Clock if I set the seconds hand. The clock takes up a continuous full core (25% of overall CPU) while the seconds hand is running; if the seconds hand is off then CPU utilization is 0% between minute updates. Other gadgets are similar, but many such as Calendar, Weather, and some non-MS gadgets work perfectly fine. Must be some kind of javascript issue. I have Avira Antivir before & after upgrade to Win7, so AVG isn't the issue for me - I even tried with Antivir and Comodo Firewall turned off. UAC on.
This machine is FAST & it can't handle a little gadget. (7.2/7.3 Windows Experience subscores on all but hard disk, which is 5.9) Didn't have this issue in Vista x64 Home Prem.
edit:
Checked the Win7 Resource Monitor CPU tab:
sidebar.exe - While not under heavy CPU load, "Analyze Wait Chain..." from context menu continually shows "One or more threads of sidebar.exe are waiting to finish network I/O", and indicates thread 4140 which is WinInet.dll (Internet Extensions for Win32 application extension.) Under heavy CPU load, several other threads starting from sidebar.exe were indicated from the same message from "Analyze Wait Chain..." as well.
All other non-sidebar processes indicate "running normally" from "Analyze Wait Chain..."
Another clue: If I login using the "Administrator" account, there is *** no performance problem ***! The sidebar.exe shows as "running normally" from "Analyze Wait Chain..."
So I also tried:
- w/UAC turned off on the normal user (administrator rights) account (no fix)
- tried creating a *new* normal user (administrator rights) account; still sloooowwww (also try this one w/o UAC, still bad)
-Problem Status: normal User Accounts have the sidebar performance problem, Administrator account runs fine.
Edit: 12/31/09
SOLVED!!!!
After digging into the sidebar.exe output from Sysinternals Process Monitor, I noticed a peculiar difference between the output for the properly functioning Administrator account & my User accounts. The admin acct showed the monitor profile for a good number of operations, while the User accts showed the wsRGB.cdmp value for the same operations, which was peculiar because I had my User accounts configured to use the system defaults, the same way I had the admin acct configured.
Going into the Windows Color Management, Advanced tab, I found that if I chose either of the "virtual device model profile" choices for the "Device Profile" setting, the performance hit was instant. If I used any of the "normal" icm profiles, performance was good. So I changed my system default Device Profile from "sRGB virtual device model profile" to the std sRGB.icm profile & everything is working great!
Note: In addition to the Gadgets, this also impacted the Windows Media Center Internet TV listings performance, which was also back to good performance after this WCM setting change. I'd expect there are numerous other apps that could be affected by the "virtual device model profile" handling. Googling "virtual device model profile" seems to bear that out, as I see others who ran into app problems when using that in the WCM applet. -
High cpu utilisation while generating HUM reports
Hi
i am facing the issue that while generating the HUM reports the CPU utilisation going to 100%. i am using HUM 300 + LMS 100. right now i am using 2GB RAMyou're right. i forgot that i made some changes to my igoogle page. the chat function is the culprit. adding it causes the spike. i've reported the problem. thanks for the help!
-
CPU clocking 100% for Master Scheduler
Hi
Most of the time my Master scheduler is clocking 100% CPU. There are 6 process schedulers. 2 are dedicated process scheduler(not defined as online app servres in Configuration.properties file on Webserver) where as 4 are process scheduler as well as online app servers. Problem is that all those users who are connected to Master scheduler server are experiencing Performance issue. Other 3 online servers are not so engaged as CPU utilisation for them is between 6% - 20% only.
My question is is this set is adviceable ? or making one of the dedicated process scheduler as Master scheduler will help?
My hardware configuration of all appservers is 2 x 2.4 Intel Xenon HT and 3GB Ram.
Regards
Vishal MahajanHi Marchiom
Thanks for your reply. Following were the processes that are running on Master Scheduler at time when it clocked 100%.
pspubdsp.exe
psqrysrv.exe
jsh.exe (20 different instances)
pssamsrv.exe
psappsrv.exe (350K x 2 instances)
Not sure which one was keeping CPU occupied? I'll keep an eye again and see which one is picking most CPU%.
Regards
Vishal Mahajan -
I have 2 CSS11501's configured with redundancy between them. On certain occasions I am noticing that the master is becoming the backup for a very short period of time, I think it is due to the fact that CPU utilisation on the master or backup is getting very high (90% plus) therefore causing the redundancy to kick in. I have had sniffers on the network to check that nothing is targeting the CSS's and causing the CPU to go through the roof or that the CSS's are getting overloaded with services going through them. Can anyone offer any other explanations ?
You can check to see which processes are consuming your CPU resources in debug mode:
CSS11501# llama
CSS11501(debug)# symbol-table load SPRITZ
Loading string table... 639,377
Loading symbols........ 23,571
Load complete.......... 1,205,081
CSS11501(debug)# cpu monitor 1 1 50
CPU Monitor Debug Options (1/1) threshold = 50 verbose = OFF
c) Clear data
d) Display data
Please enter selection [q=Quit]:
Select 'd' over the course of several minutes to gather a list of the processes that are utilizing more than 50% of your CPU. Note that the '50' in the command above is a threshold variable that you can set to whatever you want.
~Zach -
Hi,
The issue is my CPU utilisation is unusually high. I've got a dual core laptop and one core is at 100% all of the time. When I run top I can see that rpcbind is responsible for the high CPU usage. If I reboot the problem starts immediately.
I've only noticed this problem quite recently, but can't think of anything I've done that may have caused it.
This problem is really quite urgent because if I can't get it solved I will have to spend days installing another OS because at the moment my laptop battery is draining really fast.
Does anyone know what may be causing the problem, or how I can troubleshoot it?
Thanks in advance.I figured out the problem. When I upgraded my kernel the other day it turns out that the kernel was installed on my root partition instead of on my boot partition because /boot was not mounted at the time. As a result my old kernel was still being booted, but parts of the system were affected by the new kernel supposedly being installed. So what I did was mount the /boot partition, reinstall the latest kernel and reboot the system - problem solved - no rpcbind taking up 100% of the CPU now.
In the end I decided to scrap fam and use gamin anyway, based on the wiki recommendation. -
I have been using Thunderbird for a couple of years. On Friday 10 Apr my home email account stopped sending either new messages or replying to incoming emails. In addition I have Thunderbird get my work email and I can send and receive email just fine. I can also send email from my android phone and via the web.
The message that has started coming up is the following:
An error occurred while sending mail. The mail server responded: 5.7.1 [P4] Message blocked due to spam content in the message.. Please check the message and try again.
I have tried reinstalling Thunderbird but nothing changed, I tried changing the port from 25 to 587 to 465 but nothing changed. I do not understand what is going on as on Wednesday Apr 8 everything was working just fine.I have just tried ringing RCN and they tell me that because I am not using an RCN email as such they can not help but he suggested that it was a filter in Thunderbird but I have not set any filters and can not see if there are any or how to change them. The only way sending my website url right now is to make it not look like a url. Where do I need to look to solve this as I first wrote last week everything was fine.
-
Oracle Database 11.2.0.1.0 CPU hit 100% on Windows 2008 R2 64 bit Hyper-V
Oracle Environment Detail:
Oracle Database Enterprise Edition :11.2.0.1.0 (NON RAC, No failsafe)
O/S: Windows 2008 R2 64 bit (6.1)
Specifics: Virtual Server using Hyper-V
Memory: 9 GB RAM
Processor: E5540
Specific about the issue:
I have two database instance created on this server with ‘memory_target=3600M’ each.
I am getting into an issue where I find NO activity on database except regular schedule job running using DBMS_SCHEDULER –
• Database FULL export DAILY schedule time 7 & 7:30 PM accordingly for both instance (takes about 15-20 mins each)
• Database FULL RMAN DAILY schedule time 9 & 10 PM accordingly for both instance (takes about 35-40 mins each)
This was set up on Feb 25th 2011. Since then we have encounter CPU hit 100% TWICE in this system at around 8:30 PM (SAME TIME). Both database instance exports keep running and never finish. While RMAN schedule job has NO problem. Mostly everything runs every smoothly without any issue.
Replicate the issue:
I am unable to replicate this issue and do not know the cause of the issue.
Work Around:
Oracle services shutdown/Server reboot.
Would anyone know about this issue? Have any information could help? This system will become production soon and want to make sure we have solution for this.
Thanks in advance!I am finding that CPU hit 100% is very specific to Oracle 11.2.0.1.0 Export Utility (exp) used to take FULL database export. I understand Original Export is desupported from general use as of 11g but available for specific need.
Have anyone faced this issue with 11.2.0.1.0 Export Utility (exp)? Please help.
I have a need to use export utility which gives us migration options.
Thanks!
Maybe you are looking for
-
Error while executing the service request : : Login to Mail Service failed
I am getting the following error in Convergence while attempting to authenticate against the mail service. I am able to access the backend mail service directly from a mail client with the same account without any issue. Looking at the log file info:
-
We have a couple of users who have this problem occur at random times. They will have a bunch of shares mounted but there is one particular share that just refuses to disappear when the user "disconnects" from it. They can still browse the share afte
-
Problem in Creating New position in Siebel CRM 7.8 using java program
Hi We have Siebel CRM with Business Object and Business Component as Position. Position Business Component has a manadatory pick list Division. When we try to create a new Position by picking the Divison then we are getting the below error Logged in
-
I've just put together my system: Intel i7 2600K MSI Z68A-GD80 (G3) 2x4GB Corsair XMS3 DDR3 1600Mhz C9 Sapphire ATi Radeon HD 6950 2TB Samsung HDD Windows 7 Ultimate x64 SP1 I've just tested the system using the LinX stress test with the latest Linpa
-
Problem - insert JSON string into table in CLR function
Hi I create a CLR function to insert JSON string into table. With this line mt = JsonConvert.DeserializeObject<MyTable>(jsonStr.ToString()); The class is OK (no error), but when I try to add the Assembly in Microsoft SQL Server Management Studio, it