Ceaseless rapid blinking green

Recently my 3.5 year old Airport Express stopped working. When it's plugged in I get a rapidly blinking green light, but I can't connect to it through the Airport Utility. I've tried to reset it, but nothing happens, the light just keeps on blinking even while the reset button is depressed.
Any suggestions outside of buying a new Express?

droidlover0810 wrote:
is there a way to change the color of the blinking green light?
Only if the app itself lets you choose a different light color.
I downloaded the new Yahoo! email app and the light blinks purple when I get my yahoo mail, green for Gmail, but there's no way to choose that color. I've seen red, blue (from Handcent-I think), and I  think yellow, so the flashing light is capable of shining in different colors. 

Similar Messages

  • Cisco 1131AG LWAP status led yellow and other leds blinking green

    I have a problem with three AIR-LAP1131AG-E-K9  that joined the controller and the status led turns to yellow after joining the controller while other LEDs are blinking green.
    The APs has no coverage at all although the WCS shows that there is coverage and the 4400WLC shows that the AP interfaces are UP. (The ethernet interface and tha 802.11b,g radio interface is up).
    The SSID broadcast is enabled.
    On the switch the interface is up and there is traffic going in and out of the LAP.
    I tired power reset and factory reset for the APs but the problem remains the same.
    Any ideas for what might be the problem ?!!
    Regards

    Yes the clients are not able to see the SSID broadcasted by the AP.
    But these APs were functioning normally before without any changes to the WLC config.
    I had the same problem with other APs but they went back to normal state after a hardware reset to the APs.

  • 2nd gen Shuffle not syncing blinks green and orange

    My mom got a new computer. I installed Itunes and connected her 2nd gen Shuffle which previously had been administrated by her niece's computer. I deleted all music,restored to factory settings, bought new music but am unable to get music on her shuffle. Her shuffle appears in Itunes sidebar and in computer. Says it is syncing but no music is on Shuffle. Light blinks green and orange, green, orange. Troubleshoot says "current user not administrator". I followed steps in relevant topics but still no music on Shuffle. HELP

    Try this page http://support.apple.com/kb/ht1238

  • Seagate FreeAgent Go is making a clicking sound and the light is rapidly blinking. My Macbook is no longer recognizing it. Is there any way to fix it or recover my files? The SeaAgent is less than a month old!

    Seagate FreeAgent Go is making a clicking sound and the light is rapidly blinking. My Macbook is no longer recognizing it. Is there any way to pull all the songs I have saved on it? The SeaAgent is less than a month old!
    Does anyone know how to fix this issue?
    Or at least recover the lost data?
    Thanks!

    How to fix: the drive is in warranty, so contact Seagate for a replacement.
    How to recover your data: Do you have backups? (If not, you really, really, should.)
    You can try downloading Data Rescue, which will run in trial mode and let you know if the data is recoverable. (You can then choose to purchase the full version if it works for you.) A clicking drive, though, is usually (though not always) a sign that the drive cannot be recovered.
    Matt
    Edit: fixed link.

  • Blinking Green Light! Mount & Unmount on Intel Mac mini

    Hi all.
    This is my sister's iPod shuffle, lat night she plugged into her new Intel Mac mini Core Duo, and the shuffle mounts, everything appears to be in working order, she said today she still listened to it.
    Just now she accidently plugged the shuffle while in our Dad's account (on the Mac mini as well), then seemed like "all well broke loose", this is what she told me, first iTunes was not responsive, colour wheel, so she restarted but only arrived at the blank desktop and only the shadow of the Top Menu Bar
    I reset the iPod shuffle, was successful in plugging it in, quit iTunes (all in her own account now) and update the shuffle software.
    When inside iTunes, once I started Autofill, it suddenly unmounted by itself, followed by the red exclamation error message when you accidently remove an external device unproperly.
    When I tried plugging in again, it refuses to mount. Just blinking Green, or pull out again, blinking Yellow.
    Now I plug it into my own iMac G5, and it mounts and is blinking slowly with yellow light, what seems to be normal charging.
    Has this something got to do with the Intel Mac??
    Thanks and cheers

    This probably has nothing to do with the Mini, but everything to do with the Shuffle. Like all flash memory, it is susceptible to damage if unplugged at the wrong time.
    For the shuffle, you cannot remove it while it is updating or in Disk Mode. This warning is presented in the User's Guide and is repeated in several other places throughout the Support pages as well.
    The general rule is: If it's blinking amber, don't unplug it before you unmount it. Unmounting can be done either in iTunes or in the Finder.
    About all you can do, given the symptoms you're seeing, is try to Restore it. See the instructions in the User's Guide and/or on the iPod Shuffle Support Page.

  • Cisco AIR -LAP-1142 status led continuosly blinking green

    hello all,
                I have implemented around 46 access points (AIR-LAP-1142) in a customer site and i can see that the led of some of the access points are continously blinking green and no clients are associated to these access points. I have a WISM which has two controllers in it. I can see the particular aps to be joined  in the controller. But my question is that why its not giving me any signal. Please help me as this is very urgent!!.. even if am under the access point the signal is not there. I checked the radio status of the aps and its up. The WLANs are activated from the controller also. Please help mee....!!

    continously blinking green
    This could mean that the AP hasn't joined the WiSM yet.
    Can you console into the AP?  If you can, reboot the AP and post the entire power up and bootup process and include the "sh logs".

  • Airport Express Continues to Blink Green

    I got a airport express for my birthday and when trying to set it up it just blinks green. I plan to use it with speakers but i have also tried it as a router with the same problem. I have tried to reset and same problem happens. Any ideas?

    Start over by resetting your AirPort Express (AX) back to factory defaults as follows:
    Power down the AX for a few moments
    Hold in the reset button and keep holding it in as you plug the AX back in to power
    Release the reset button after 10 seconds
    By default, the AX creates a wireless network with a name like +apple network xxxxxx+, where the "x" can be either a letter or number. You will need to log on to this network with your computer. Once you have done this, you should be able to open AirPort Utility to "see" the AX.
    Click "Continue" and follow the guided setup to configure your AX.

  • Desktop won't start; blinking green light

    I have a Compaq Presario SR 1318NX which will not start!?  There is a blinking green light on the back of the power supply; which is normally solid green when 110V AC is plugged into it.  I have tried the trick of holding the start button while plugging in the power cord ..... no help.  I have also opened the case and carefully removed every power cord to all the internal devices ................ the light turns solid green only when I pull the main power from the motherboard!
     Do I need to replace the motherboard?  The troubleshooting site on hp.com would indicate the power supply is OK if the light is solid green.
    Thanks for any suggestions,
    Lou
    This question was solved.
    View Solution.

    My wife's computer has been having the same problem several times. One solution I found that worked before was to unplug the motherboard power cable and the PSU power cable from the back of the PC and then connect the power cable and connect the motherboard power cable while holding down the power button. Scary, to say the least, but it worked, until one day I accidentally flipped the wrong breaker and then spend two hours trying the same solution with no luck and Googling again. And here is what I found. This is the simplest yet crudest solution. It’s easy and non invasive and it doesn’t matter how tech savvy you are. Take a blow dryer and turn it on to blow air at the back of the power supply for a couple minutes. When you see the light turn green you’re all set. It's worked for me after it worked for a hundred others, maybe more. See the testimonials on this site: http://talk19.wordpress.com/2008/01/13/hp-m7088d-power-supply-led-blinks-green/. It’s a shame that nothing like this appears on any HP site. So don’t waste your money on a new MoBo or PSU. All you need is your wife’s hair drier.

  • What do I do when my macbook pro just shuts down and when I plug my charger in, it faintly blinks green and yellow and doesnt charge?

    what do I do when my macbook pro just shuts down and when I plug my charger in, it faintly blinks green and yellow and doesnt charge?

    Hi aaliyafrommarkham,
    In order to troubleshoot this, I would recommend that you start with an SMC reset. Information on this procedure can be found here:
    Intel-based Macs: Resetting the System Management Controller (SMC)
    http://support.apple.com/kb/HT3964
    Thanks for coming to the Apple Support Communities!
    Cheers,
    Braden

  • Tablet fails boot, red light, then blinking green....GRRR!!

    Just as my tablet recieved the OS update, it no longer booted.
    It was fully charged, and plugged into a standard micro USB at the time.
    It said download was successful, restart now... so I did.
    And I never could use it again.
    When I tried to boot it, it had a red light, then the red light blinked a few times, then nothing.
    And then, it blinked green six times. then nothing.
    I tried a USB to my computer to use Blackberry Manager (latest version).
    I tried of course, the various holding down the power button schemes, including the old one of holding down ALL the keys, and the new one with just the power and forward keys.  Nothing.
    I went on EBAY to get an OEM charger stand.  I hope that works, but I don't have much hope for that.
    And now, nothing.  My blackberry is a brick after the update.
    I came to like blackberry because of the reliability of the phone.  While all of my iphone friends were crazy about tech support of apple, I replied, I don't need tech support with my blackberry (curve) nothing ever goes wrong.
    But this whole situation, is getting me down.
    Solved!
    Go to Solution.

    Connect it to the OEM wall outlet charger.
    Press and hold down the power key ONLY for 20 seconds.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Have installed Airport express using windows vista, unit blinks green, selected the speakers from itunes but get no sound at all, even if I put a headphone in the airport express. Pls advise

    Have installed Airport express using windows vista, unit blinks green, selected the speakers from itunes but get no sound at all, even if I put a headphone in the airport express. Pls advise

    If the AX is working properly, it should not show up in your list of available networks (since it is "joined" to your router). Have you unplugged and replugged your AX? Unplugged and, after a minute, replugged your router? Do you have MAC address filtering enabled on your router? (if so, disable it to see if the AX works ... it will broadcast its MAC address to the router, and you can add it.) Is your firewall turned on? Turn it off and see if you can access Airtunes. You will have to open a port in your firewall if that is the case.
    The AX should have the same network name as your router the wireless tab. When it shows up, what name is it broadcasting?

  • FBUS-HSE/H1 not detecting 100Mbps and status light blinking green

    I had the HSE/H1 connected to my network, but it decided to go crazy on me and drop off the map. I know the IP Address of the unit, but am unable to connect with it anymore. I did a factory reset on the unit, but am unsure if that resets the IP address as well. If that is the case what is the best way to force an IP address on the unit? The status light blinks green at a rather fast rate as well. I can add the ethernet interface board in the interface fonfiguration utility, but can not add the hse/h1 LD since it just sits there and listens for the board forever. I hope it is an easy fix and not a matter of the unit died on me.
    Thanks
    Kyle

    The blinking status LED indicates that the linking device is in standby state. The linking device will be assigned an IP address automatically through DHCP. 
    Please check whether the linking device and the host PC are in the same subnet. Otherwise, the linking device will not be detected.
    Feilian (Vince) Shen

  • HT1655 i can't hear music and i know its on it, i can see it on my comptuer. now, it is blinking green then orange.

    I found my old ipod shuffle. It has music on it. But, i can't hear it.
    I tried reseting it. Now, it blinks green, orange, green, orange, so on.

    I figured it out.
    When you plug them in, you have to adjust the volume directly from the headphones or you don't hear anything. So use the little control on your apple headset and the sound will work. I feel like such an idiot for not figuring that out sooner *facepalm*

  • ITouch camera blinks green and black, sometimes purple

         I have an iTouch 4G and a few months ago I dropped it, there are cracks but everything worked fine, now after five months the camera will not work. The screen blinks green and black and sometimes purple, I reset it, restored it, but it still doesnt work. I'm sure it wasn't from dropping it because it's the camera on the back that does not work. I'm still eligible for the warranty but will they not honor it because of the cracked screen? Thanks

    Apple will exchange your iPOd for a refurbished one for $99, $149 or $199 depending upon the capacity.
    Accidental damage like dropping the iPod voids the warranty for the entire iPod.

  • Background contrast on Apps screen & blinking green light

    Newbie here.  The Apps screen had a blue background but is now white and I am unable to read the titles of the icons at the bottom of the screen.  How can I get rid of the white background and return to the blue contrast?
    Additionally the green indicator light is blinking non-stop.  Why is it doing that now when it never did before?
    Thanks!  

    Greetings, and welcome to the forums!
    Not sure about an answer to your 1st question, but the blinking green light simply means that your phone is connected to your carrier. I use it just so I know at a glance whether my phone's actually on or not. To disable that blinker, go to Options > Screen/Keyboard > LED Coverage Indicator and change the setting to "off".
    "Cats may taste like chicken, but they have more bones than rabbits."
    Blackberry 101
    Tips & Tricks
    Videos to learn from on youtube

Maybe you are looking for

  • Diff bet. run_product and srw.run_report

    In reports 6i is there any difference in architecture between using run_product and srw.run_report(which according to 6i doc calls rwrun60.exe)? The reason is I that have the same report submitted by the above two processes produce font difference in

  • Display form guide in browser using ES2

    I am trying to render a form guide in worspace and also in a browser so you can access the guide via a url outside the workspace environment. Can someone refer me to a good guide or tutorial for this. Thanks

  • Strange problem... any ideas?

    I started out with a working JavaHelp system, copied it to another development folder, added the same type of code to my new application, to display the same help, but it didn't work. The help sets are found, but the only thing that is displayed is t

  • Add radio button when a radio button is selected (pop up)

    How do you Add a 2 radio buttons when (pop up when d1 is selected) For example d1a and d1b When d1 is selected. <cfoutput> <cfif isdefined("url.msg")> #urldecode(url.msg)# <BR /> </cfif> </cfoutput> <table border="0" cellpadding="5"> <form id="form1"

  • Inbound for Service ticket creation

    Dear all, An inbound FM being triggered for Service ticket creation which those info are coming from legacy system. My requirement is, at the end of the inbound processing, i need to send back the newly created SAP ticket number back to legacy. I fou