Cellphone turns off after 5min after i inserted a ...

my cellphone model is 6300. i inserted a bsnl sim in my cell n after that it got hung. i removed it n inserted the previous one and switched on my cell. but it would switch off after every 5 min. the bsnl sim works fine in sony erricsn cellphone.
i just cant understand what went wrong. help.

You have probably fixed the problem by now, but I also just bought a Nano and it was very frustrating with the music shutting off before the first half a dozen bars of the song.  I rang Apple and they sent me this page.... (if anyone else needs help)
http://support.apple.com/kb/TS3700?viewlocale=en_US
All it was that I hadn't pushed the headphones in until they were flush up against the Nano.
Thanks Apple!

Similar Messages

  • Laptop turns off after 3-4 seconds

    Hi there,  My Laptop turns off after 3-4 seconds of turning in on. When the battery is plugged in or mains lead, the on /off switch does absolutley nothing. When you open the lid however, it turns the laptop on for 3-4 seconds then cuts out. After taking the laptop appart, i have found that the only way to get the laptop to turn on properly is to take out the power switch chip unit strip cable, insert it so it turns on and then remove it quickly. this way the laptoip stays on. if you insert the power unit strip cable, it turns on fine, but if you leave it in, the laptop turns its self off after 3-4 seconds ( as if the power button was held down) Do you think this is a problem with the either, the power button chip unit, the main board, or maybe even the magnet switch in the lid!? i have upodated bios/cleared CMOS, ran all diagnostics, tried everyt combionation of resetting, e.g. hd/ram/cables /power button down for a minute, bat back in power lead back in...etc, everything installed fine and came back 100% ok as if there is no problem, but the power switch is doing nothing!. Please help or let me know if anyone else had this issue, i really need my laptop working. Kind Regards, James Hardy 

    Does it do it booting in these two modes?
    Safe Boot from the HD, (holding Shift key down at bootup).
    Bootup holding CMD+r, or the Option/alt key to boot from the Restore partition & use Disk Utility from there to Repair the Disk, then Repair Permissions.

  • Yoga display turns off after 1 minute

    I'm having an annoying problem with my new Yoga related to the display and have not seen any other posts with a similar complaint so perhaps this is a simple fix that I'm just not able to sort out on my own. My display turns off after 1 minute of inactivity. The only means for changing behavior like this that I am aware of is through the Control Panel Power Options. My settings for "turn off the display" are 10 minutes on battery and Never while plugged in (note screen shot attached). Regardless of my settings, the screen turns off after 1 minute. I've changed the settings to multiple configurations and restarted with no change in behavior. Perhaps there's some other settings area, maybe something specific to Lenovo that I'm not aware of (since this is my first Lenovo laptop). Anyone with similar problems or insight?

    This may be a Windows 8 issue. I finally fixed this problem by identifying the screen saver as the issue (and I wasn't using a screen saver). Type "lock the computer" into the search box after clicking the search charm, which brings up the screen saver dialog box. Mine was set to 1 minute, though I'd never set it myself. If you can't change it, choose a screen saver and you should be able to do so (and can then switch back to no screen saver). BUT, here's the problem. Other things you install (or settings within things you install) can apparently change and override whatever you type in for the delay time. Try applying your new time and exiting from the dialog box, then open it back up again. I was finding that it kept going back to 1 minute. To reset things so that you can get control again, type "user accounts" into the search box and when the dialog box comes up, choose "Reset Security Policies". Then you can go back to the screen saver dialog and successfully change the delay time. See http://social.technet.microsoft.com/Forums/windows/en-us/ace4085a-b0ba-4a98-898d-cd92d9e88e13/window... for some detail.

  • My screen darkens after 1 minute and turns off after 3.  All of a sudden, now, after the screen shuts down, it comes right back on????

    My screen darkens after 1 minute and then turn off after 3 minutes (energy saver).  Now, all of a sudden, after it shuts down it comes right on???

    thank you so much sir... i am very thank ful to u... it was an breath taking moment ... i was almost dead as it didnt work

  • Screen turns off after a few minutes and needs to be closed then opened

    hi, as the title suggests my powerbook screen turns off after a few minutes before my screensaver is set to come on and when i come back and press a key or move the pad it wont start up so i need to close the powerbook then open it up again for it to activate. its not a huge problem but my programs which connect to the internet seem to lose their connection when i open it up again. is this normal? is there a setting i can change?
    thanks
    ross

    Is there a way to "disable" Standby, Suspend and Off just when watching movies (in fullscreen or not)? I want them to do what they usually do in all other cases.
    Setting them to 0 in xorg.conf does the thing, but I need that functionality only when I'm wathing movies. Making a script that alters adjustments in xorg.conf isn't the best solution - you'd have to restart X every time you want to watch a movie .
    Cheers,
    Daniel

  • For the iphone4, my light is on all the time! the light is supposed to turn off after a few seconds of use. how can i fix this?

    for the iphone4, my light is on all the time! the light is supposed to turn off after a few seconds of use. how can i fix this?

    If what Allen says does not fix the issue I have seen this as a Hardware issue and I would get into an Apple Store if it is close by
    http://concierge.apple.com/reservation/us/en/

  • MacBook turns off after the startup bong when trying to restart

    Greetings,
    When I try to restart my MacBook it turns off after the startup bong.
    Thanks

    Have you tried resetting the System Management Controller? That is a good first step for power related issues such as this.
    Best of luck.

  • TS1363 apple sign shows up and then turns off after a few seconds, and i can not connect to my itunes

    apple sign shows up and then turns off after a few seconds, and i can not connect to my itunes

    I have the exact same problem trying to use the Remote app on both my iPhone 3gs and iPad 2 with either my Mac or ATV2.  My Remote app used to work on my phone - I can't recall if I ever actually used it with my iPad, but when I tried today, I got all the same results as you did (on both iPad, and then iPhone).  I  was using my ATV2 to play music from iTunes on my Mac and wanted to use the Remote app, but it would not connect to either device no matter what I did. 

  • My ipod shuffle turns off after exactly 30 seconds of play. Already had a similar problem?

    My ipod shuffle turns off after exactly 30 seconds of play. Already had a similar problem?

    Did you see my post above?
    Have you tried a different set up earbuds to see if that helps?
    What about resetting the Shuffle?
    Resetting iPod shuffle
    B-rock

  • HT1430 my iphone 4 turn off after appearing message "temprature high, need to be cool down after than doesn't becoming turn on"

    my iphone 4 turn off after appearing message 'temprature high, need to be cool down' after that does not getting turn on by anyhow.

    Hello vijaypatel,
    Thanks for the question. The following article outlines the temperature warning that you experienced:
    iPhone, iPad, and iPod touch (4th generation): Keeping device within acceptable operating temperatures
    http://support.apple.com/kb/HT2101
    If the iPhone is no longer powering on, we will need to isolate this issue to determine if it is hardware related.
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    - Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
    - Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion.
    Learn about LCIs and corrosion.
    - Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    - After at least 15 minutes, if:
                   - The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
                   - The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
                   - Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
    - If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
                   - If the display turns on, go to step 4.
                   - If the display remains black, go to next step.
    - Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to
    restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    - If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
    Thanks,
    Matt M.

  • Iphone turns off after a few mn of utilization with the battery full

    My iphone 3GS turns off after the battery is fully regenerated. I can only use it a few minutes before it turns off. I have to plug it again to turn it on, and the indicator of charge is around 98 %. The problem does not come from the battery. Has anybody found the same dis-functioning? A solution? Thanks!

    More than likely the iPhone has a hardware problem.
    If there is an Apple store nearby, make an appointment to have this confirmed.

  • 10.6: Internet Sharing turns off after restart

    I use Internet Sharing on my iMac to share the Ethernet connection from my computer wirelessly to my iPod touch. In Leopard, Internet Sharing would turn off after a restart. Snow Leopard fixed the problem for a while, but now it's acting up again. Any help?

    Using MacOS X 10.6.2 I have the same problem.
    My network configuration is just the other way around (wireless Internet and Ethernet LAN).
    Looking this up in Google first, I came across this older support link of Mac OS X 10.2:
    http://support.apple.com/kb/TA21168?viewlocale=en_US
    The solution provided there is not really helping though.
    However, it appears that this is a recurring issue Apple is struggling already longer with. Hope they straighten that out at one point.

  • HT4061 Iphone suddenly turned off after it was working fine. How can I turn it on again?

    Iphone suddenly turned off after it was working fine. How can I turn it on again?

    Hi Bobgriff43,
    If your iPhone will not turn on, you may find the following article helpful:
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/ts3281
    Regards,
    - Brenden

  • Yoga 13 display does not Turn off after idle

    I have the computer set to the balanced power option, and the disaplay is set to turn off after 5 minutes on battery and 10 minutes when plugged in. Unfortunately the screen never turns off.
    Anyone know how to fix this problem ?

    hi tmpst,
    Welcome to the Lenovo Forums.
    If a wireless device (mouse, keyboard, etc.) is plugged to the computer, the display, screen saver or sleep function might not work. If this is your case, try to:
    1. Remove your wireless device (might include a usb dongle)
    2. Apply the Moving mouse causes laptop to exit sleep mode fix
    If you have Power DVD installed, apply http://support.microsoft.com/kb/913405
    Let me know your findings.
    Cheers.
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • My ipod only goes to the apple screen and freezes then turns off after about a minute. Is this fixable?

    My ipod only goes to the apple screen and freezes then turns off after about a minute. Is this fixable?

    Try a system reset.  It's quick, easy and harmless...
    Hold down the on/off switch and the Home button simultaneously until the screen blacks out or you see the Apple logo.  Ignore the "Slide to power off" text if it appears.  You will not lose any apps, data, music, movies, settings, etc.

Maybe you are looking for

  • Error while creating Structure

    I am getting an error while creating a Structure. After filling the required fields in Components tab and Currency/Quantity filed tab, when activated it says "Warnings Occurred during activation"  "Do you want to see the log?" when i click "yes", it

  • Need to capture the output of parseEscapedXML() function in a variable

    Hi All, In my BPEL process, I am fetching the XML data from the database which is stored in a CLOB column, using the database adapter. As it is in a string type I am using parseEscapedXML() function to get the XML data out. I have done the following:

  • Export problems - Error compiling movie - Unable to Create or Open output file

    I've got a weird one here.  I cannot export projects to my main render Raid-0 harddrive, but I can to any other drive.  This is not unique to Premiere.  It's happening to me in AE and Cinema 4D, so I'm sure it's not an Adobe problem.  But I'm posting

  • Wi-Fi Networking in Location Services System Services

    Hello, I'm trying to figure out what the "Wi-Fi Networking" toggle controls.  This is located withing Settings > Location Services > System Services > Wi-Fi Networking. Thanks for the help if anyone can provide any.  I've been searching around the we

  • Web browsers not loading webpages

    Overnight, a couple of days ago, my web browsers (Safari and Chrome) both stopped loading webpages. When I click on a link, I get a blank page. But when I am logged as a guest or browse through Vmware's windows I can still browse normally. Thanks for