Centro reboots when hotsync button is pressed or hotsync application is selected on the Applications screen

I had a Sony CLie (palm compatible) before and was using palm desktop for CLIE. I just bought Centro, installed palm desktop, hotsync worked fine. I had decided to 'copy everything'. All my contacts are now in centro, but now when hotsync is selected, Palm reboots. I rebooted my PC but no use. I tried using hotsync button as well as hotsync application icon in applications screen to the same result.
The other minor issue is how to take the hotsync cable out of centro? its tightly fitted in centro.
Post relates to: Centro (AT&T)

There is no Reset button on a Centro.
To soft reset a Centro, you remove the battery, wait at least 10 seconds, then replace.
Sending all the Clie's data and system files into the Centro may be the cause of all the problems!
Did you follow Palm's guide to updating to a new device?
How to Upgrade from a Previous Palm device to a Newer One: http://kb.palm.com/ and enter 12926 (General Upgrade guide) or 45175 (Upgrade to Centro) into the "solution ID:" box (lower right).
I'd try a Soft Reset first, check for normal operation. If it still malfunctions, you need to Hard Reset the device and rename you /Backup folder before doing another Hotsync.
WyreNut
Post relates to: Centro (AT&T)
I am a Volunteer here, not employed by HP.
You too can become an HP Expert! Details HERE!
If my post has helped you, click the Kudos Thumbs up!
If it solved your issue, Click the "Accept as Solution" button so others can benefit from the question you asked!

Similar Messages

Unlike IE When back button is pressed it takes too long. pleas do something for that. thnx.

Unlike IE When back button is pressed it takes too long. pleas do something for that. I like firefox and i get to use the back button more often.
thnx

In order to be able to find the correct solution to your problem, we require some more non-personal information from you. Please do the following:
*Click the Firefox button at the top left, then click the ''Help'' menu and select ''Troubleshooting Information'' from the submenu. If you don't have a Firefox button, click the Help menu at the top and select ''Troubleshooting Information'' from the menu.
Now, a new tab containing your troubleshooting information should open.
*At the top of the page, you should see a button that says "Copy text to clipboard". Click it.
*Now, go back to your forum post and click inside the reply box. Press Ctrl+V to paste all the information you copied into the forum post.
If you need further information about the Troubleshooting information page, please read the article [[Use the Troubleshooting Information page to help fix Firefox issues]].
Thanks in advance for your help!

Changing Navigation when cancel button is pressed

Hello All,
We are having custom responsibility for Offer and vacancy creation. New Menu of type(App Pref Menu Container) is created and the required functions and sub menus are attached to it. This was done earlier by someone else. Now when ever i start a transaction (i.e. create offer) and then cancel it, it goes to the custom home page of that responsibility. Now i want to change the navigation page when cancel button is pressed. I believe it was achieved through menu only. Can anyone suggest how?
Thanks and regards,
Pradeep

If a user is halfway ....Look at it this way...Various wizard pages insert rows into various tables. Mark all of them (or some appropriate "master" record) with a "Pending" flag.
Pressing Cancel is nothing special, just like closing your browser window, the Pending data would continue to hang around.
You could set up background jobs that purge pending data older than N days or something if you like.
What I was suggesting was that the "start wizard" button/process should first delete all these Pending rows before starting its real work.

Add a new check box when a button is pressed??

I was trying to add a check box dynamically when a button is pressed.
The check box contains title and a textbox for the user to enter data.
For example , when the user hits addnew button , a new check box (title-name)
with a textbox for entering name should appear on the form.
Please help
thanks

ganeshpuppala wrote:
Hi ,
Thanks for the reply , I want to just do the task in java script.
Can you explain with an example.
thanksSince you are on a Java forum, I can only assume you want to be talked out of using JavaScript. And since you didn't indicate your choice of GUI toolkit, the default assumption is that you want to use Swing. Congratulations! Start here:
[http://java.sun.com/docs/books/tutorial/]

Create a validation that runs when a button is pressed

Hi good people from this forum, I was wondering if it's possible to create a validation that runs when a button is pressed.
I'm using Oracle Apex 4.2.2 with Oracle Apex Listener 2.0 and Oracle Database XE 11g
Thank you so much for your time
P.S. On another note, How can I change my display picture =P?

You can create a validation and give it's condition like 'When Button Pressed' and select a button name or select the Condition Type as 'Request=Expression1' and give request(button name) in Expression1.
Thanks
Lakshmi

My iPhone 6 wont come on when home button is pressed and screen pixels out and fades. Any one have fix or same problem?

My iPhone 6 wont come on when home button is pressed and screen pixels out and fades. Any one have fix or same problem?
When I press the home page the screen activates but stays black. I have to press the side button to turn if off then may have to repeat several times to get my phone to come on. Sometimes while using the phone the screen will become pixelly and start to fade away leaving a white screen with vertical line on it. I have to use the close button to make it go away.

If one of the two major buttons of your phone is broken, it is unfair to expect normal operation to be available. The first resolution to any problem involves a usable Home button, as does the second option for resolving any problem. Get your Home button fixed.

TS2634 Why does my apple iPod touch just automatically stop playing songs and it also when I am doing a google search just goes back to the home screen

My iPod touch just stops playing songs automatically.
When doing a google search it sometimes times goes back to the home screen.
Also it sometimes takes several goes before it will accept the charger!
Would appreciate any help, thanks

- The charging issue could be due to a poor connection or a problem with the iPod. Try another cable first
- Try the following, it is mainly for the not playing and other problems:
Reset. Nothing is lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Restore from backup
- Restore to factory defaults/new iPod
If still problem time for an appointment at the Genius Bar of an Apple store.

My iphone 4 wont connect to my wifi, it usualy works fine, when i go to settings it says its connected but on the home screen it still says 3g and is running at 3g speeds still, please help :)

my iphone 4 wont connect to my wifi, it usualy works fine, when i go to settings it says its connected but on the home screen it still says 3g and is running at 3g speeds still? please help

http://support.apple.com/kb/ts1398

I have a ipod touch 8gb when i plug it in to charge it just blinks from the apple screen to the battery screen but will not charge what could be wrong it was fine yesterday?

I have a ipod touch 8gb . When I plug it in to charge it just blinks from the apple screen to the battery screen what could be wrong?

Maybe:
- See:
iPod touch: Hardware troubleshooting
- Try another cable
- Try another charging source
- Look at the dock connector on the iPod. Look for abnormalities like bent or corroded contacts, cracked or broken plastic.
- Make an appointment at the Genus Bar of an Apple store.
Apple Retail Store - Genius Bar
or
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

I have to press menu many times to get to the main screen? This just started happening.

I have to press menu many times to get to the main screen? This just started happening.

If you believe your Device to be faulty...
Take a Visit to an Apple Store or AASP (Authorized Apple Service Provider) and have it evaluated...
Be sure to make an appointment first...

HT201210 my iphone is stuck on the itunes screen and when i try to restore it it just go back to the itunes screen how do i get out of it

my iphone is stuck on the itunes screen and when i try to restore it it just go back to the itunes screen how do i get out of it

Connecting in recovery mode will help: http://support.apple.com/kb/HT1808

When I start up my Mac it won't go past the grey screen. Any suggestions?

When I start up my MAC it won't go past the grey screen. Any suggestion?

Mac OS X: Gray screen appears during startup

Centro rebooting when capturing video.

Hi,
I searched the forums, but couldn't find anyone else with the same problem.
I have a Centro, and a SanDisk 4GB Micro SDHC card.
I use the CamCorder app that came with the Centro to do video recording.
Whenever I record a clip longer than about 20 seconds, when I stop recording, the Centro reboots. When it comes back up, the video has been recorded, but it is a pain that it reboots every time.
Everything else seems to function as normal.
Could this be a problem with the SD card?
Also, what other apps would you recommend for capturing video on the Centro?
Thanks!
Post relates to: Centro (Sprint)

Hello GoGo
First check if the video is being saved to the SD card. Go to the camcorder application next look near the record button is on the right and select the drop down menu. Make sure it's set to Palm.
If the video was saved to the Rom and not the SD card it might have performance issues because it's running out of memory.
Also check if you are running any third party applications the might cause corruption on the device and remove them.
"Could this be a problem with the SD card?" - probably not, just check where the file is being stored to.
"Also, what other apps would you recommend for capturing video on the Centro?" - we do not recommend third party software. But you are more then welcome to look at the following sites for applications: www.palminfocenter.com/centro-software/
http://software.palminfocenter.com/platformMain.asp?platform=1
www.everythingcentro.com/

HP Palion dv7 Notebook PC will not power up when power button is pressed.

My HP Pavilion dv7 Notebook PC will not power on when the power button is pressed. I have removed the battery, unplugged the AC adapter and pressed the power button for 15+ seconds then plugged in the AC adapter and pressed the power button for 15+ seconds. Then I release the power button and then press the power button again and the Notebook will power up and operate normally. I can reinstall the battery once it has powered up. What is causing this problem and how do I remedy the problem?

Hello Griff83147,
Unfortunately there could be a number of different things that caused that issue from drivers, software, possibly hardware. I am glad you got it up and running but there isn’t a clear picture of what actually caused. If a technician got the chance to work on it then they could at least narrow it down.
Sorry I could not answer your question, but this is one of those questions that can have multiple answers.
If you have any further questions don’t hesitate to ask.
Thanks
Clicking the White Kudos star on the left is a way to say Thanks!
Clicking the 'Accept as Solution' button is a way to let others know which steps helped solve the problem!

Tring to save data for n iterations, beginning when SAVE button is pressed

OK, I'm STILL struggling with this vi. (See post from 12/16). I've cleaned up the code considerably, and better defined what it is I want to accomplish. When the vi begins, I want to immediately begin displaying on the front panel 3 values: Indicated Flow Rate O2, Indicated Flow Rate N2, and Helium Concentration. When the operator presses the SAVE button, I want the next n iterations to be saved to file. N is determined by the Measurement Duration (in minutes) divided by the measurement interval (in seconds). After the desired number of data points are saved, the operator can press the stop button, at which time the vi goes to frame 1 of the sequence, shuts off the Helium Solenoid and returns the detector to standby. The whole key to this vi is being able to monitor the data in real time, and decide based on measurement criteria when to begin saving the data, initiated by pressing the SAVE button. Somehow, I know I need to initiate the save with the case statement, and then save the data (n-1) more times. When I tried a loop within a loop, I just saved the same data for the given # of iterations, and then the displays began updating again. Is this making any sense at all? I'm beginning to understand what an aneurism feels like.
Attachments:
Master He Concentration 12_20 V5.vi ‏88 KB

One possibility solution is attached. Basically, we have a shift register that contains zero and regulates a case structure. Case zero is empty. If save is pressed, we feed a positive, nonzero number to it , which triggers the default case that (1) saves a data point and (2) decrements the shift register. This contiunes until the shift register reaches zero again.
Modify as needed.
btw: there is no reason for any local variables, use direct wires.
LabVIEW Champion . Do more with less code and in less time .
Attachments:
Master_He_Concentration_12_20_V5MOD.vi ‏75 KB

Centro reboots when hotsync button is pressed or hotsync application is selected on the Applications screen

Similar Messages

Maybe you are looking for