CFP 2110 - Status led flashing continously

I'm running into problem with a cFP 2110.
During the debugging of my RT application on the cFP, I get an error message "Host IP address not in the access list". At this time, I was unable to download any application to the cFP. the VI server IP access list was configured with *. So all the IP address can access to the cFP.
I found a procedure on the ni web site to reset the system.
-Set to safe mode
-ftp the cFP and delete all the file
-Remove the safe mode.
It means that there is no more OS or LabVIEW RT on the system.
Now, When I restart the cFP, the Status led is flashing continously (1 flash / 1.5s) and I don't have access anymore to the cFP in MAX.. Can some one help me on this case ? .
Thanks
Attachments:
Ni_recommendations.pdf ‏126 KB

Hi Poussin,
I would recommend flipping the Reset IP dip switch (dip switch 7). This
should get the controller to show up in Measurement and Automation
Explorer(MAX) as 0.0.0.0. If you can't see the controller, you may want
to try turning off your firewall. Often computer firewalls will prevent
customers from seeing unconfigured controllers in MAX.
Once you find your controller, you can flip the reset IP dip switch back to the
off position and reset the IP address. For more information on this,
click on your FieldPoint controller in MAX that will be displayed as
0.0.0.0. In the MAX help that appears on the right, click on the link
titled, "Configure Network Settings." If you need assistance
choosing an IP address, please look at this KnowledgeBase.
Once you have assigned an IP address to the controller, the status light should
stop blinking once. You will then need to install software.
Here is a general
document that describes how to assign an IP address and install software.
Please let me know if you have any other questions.
Regards,
Ching P.
DAQ and Academic Hardware R&D
National Instruments

Similar Messages

CompactRIO unusual error status LED flashing continuously

Hi,
I have a cRIO 9014 controller with an error i can't solve.
After re-installing LV 8.5 on my laptop MAX could see the controller but with the VISA and NI-RIO error. I wanted to obtain the IP address from the DHCP server (before i used the static IP address without any problems), rebooted the controller and the status LED started flashing continuously every 1 second. (unrecoverable error or corrupted flash memory card)
I rebooted the controller several times with IP reset but LED is still flashing. Also in MAX i can't see the controller anymore so reformatting controller is not possible.
Firewall is off, crossover cable is connected, IP of host is ok but no cRIO in MAX
Found a similar problem on the forum http://forums.ni.com/ni/board/message?board.id=170&message.id=238333&query.id=24781#M238333 but it didn't solve my problem unfortunately.
Thanks for your help!
Greetings from the Netherlands

Hello TrabW,
Thank you for your post on our webforum.
Can you try to start up the controller in safe mode? Is it possible to ping the controller? Please try the default IP address and the one you entered (in case the controller didn't reset the IP). Please let me know the results,
Best regards,
Martijn S
Applications Engineer
NI Netherlands

Status LED Flashes 5 times?

There are only nine terminal bases in the back and no terminal bases were added to the bank while the power was supplied. Is there any other reason for this error? Any help would be greatly appreciated.

The status light flashing 5 times means different things for different network modules. Without knowing which network module you are using, I can not provide specific information.
It is most commonly seen with the FP-1000/1001 Serial Network modules when an I/O module is unrecognizable. This can happen in the following circumstances:
1) A module that may have been connected previously was not available when Find Devices! was issued.
2) The firmware of the network module may not be updated to support the I/O module. For the latest driver version of a FP-1000/1001, the link is:
ftp://ftp.ni.com/support/fieldpoint/Update/FPupdate.zip
3) There may be 10 bases on a bus but the system only supports up to 9.
4) There may be a bent pin at the point where the module connect
s to the base.
5) The terminal bases were connected or disconnected with power applied resulting in a bus failure condition.
Regards,
Aaron

Cabling problem? - all status LEDs flash - Link/Act, Full/Col and "100"

I have a CAT5 cable installed in my house. When I connected it to my WRT54G router and computer I have on the router all three of the Link/Act, Full/Col and 100 LEDs flash in sync. My PC tells me the LAN cable is not connected. I have reterminated the cable and still get the same dispaly on the router and message on my PC. The manual is silent on this. Can anyone help? The router's firmware is V1.02.0 and the router works fine with other cables connected to the other ports. I have tried all the ports with the cable in question. Thank you.
Message Edited by snowrider on 07-21-2006 11:58 AM
Message Edited by snowrider on 07-21-2006 11:59 AM
Message Edited by snowrider on 07-21-2006 12:02 PM

Hello,
solved the problem by my self. One statement was missing. IT was reverse-route, which is requiered to create the routing entries.
crypto dynamic-map CRYPTO_ISAKMP_CLIENT 1
set transform-set VPN-TRANSFORMSET
reverse-route

Blackberry Pearl 8100 randomly shuts off and the status LED flashes red

My pearl was reciently unlocked and changed from AT&T service to t-mobile. after this switch the pearl started having fits of rage where it will turn off randomly, weather any keys have been hit or even if it is idle. the device LED then flashes red, sometimes once, other times it will flash once every 4 seconds for hours. then it will randomly turn back on either to the exact screen it had been on before it powered off or it will reboot completley and start the normal start-up procedure and varify security checks just as if the battery were removed. i tried removing the batery and leaving the phone disassymbled for a few nights but in the morning the plague is back and unrelenting. sometimes all i have to do it pick the device up and it will shut off. other times i will be plugging away with it for 20 or so minutes on the internet and then it will die suddenly. it also cuts out in the middle of phone calls. if anyone can help,please let me know.
blackberry 8100 v4.2.1.96

Is it a new phone? If it's less then a month old see if you can return it, otherwise you can try reloading the OS.
So if you're willing to try that, do the following.
First download and install the Desktop Manager from here (4.6 without Media Manager is recommended): https://www.blackberry.com/Downloads/entry.do?code=A8BAA56554F96369AB93E4F3BB068C22
Next you can use the Backup and Restore feature present in the software to make a backup of all the data on your phone.
Next download and install the handheld software from here: http://na.blackberry.com/eng/support/downloads/download_sites.jsp
Afterwards try reloading the OS by connecting the device to your computer, open the Desktop Manager, then go into the Application Loader. This will open a wizard that steps you through reloading the OS onto your device. More detailed steps can be found here:
http://www.blackberry.com/btsc/KB03485
If someone has been helpful please consider giving them kudos by clicking the star to the left of their post.
Remember to resolve your thread by clicking Accepted Solution.

CRIO status led 2

I have two cRIO-9014 that are exhibiting the same problem... the status led flashes twice every three seconds. According to the documentation this indicates that "The controller has detected and error in its software". I can configure the cRIO from MAX but can not connect to the device from the LabVIEW develoment environement. I've tried formating the cRIO, setting up the IP addrs etc and reinstalling the software with no success. Another thing I've noticed while interrogating the cRIO using MAX is that there is a VISA Error and a NI-RIO Error present under Devices and Infaces. Is there a solution to restore my cRIO's to their original state or would I have to send it back to NI to be repaired?
Regards,
Rob

What Rev of 9014 Controller do you have? The later rev's require NI-RIO 2.4.1 due to a change in the Disk on Chip memory. Check out the following Knowledgbase:
National Instruments cRIO-9014 Disk On Chip Change Notification
Regards,
Basset Hound

CFP-2110 controller STATUS LED red blinking after powering up

Hi,
Have any one experienced this before: once we powered up the control panel to the instrument, the cFP-2110 controller would just start blinking the RED STATUS signal. I checked the manual on cFP-2110 and it says if the red signal comes off more than 4 times, it is an unrecoverable error. Any recommendation from the board?
Thanks a lot.

Hi,
The default IP is 0.0.0.0. Do you see this same behavior when booting into safe mode? Please see the cFP-21xx User Manual page A-2. You can also contact NI support at www.ni.com/support.
Lynn
National Instruments
Staff Systems Engineer

CFP status led - stays lit solid red!

Hi,
I have a problem with a cFP-2120 RT controller where the red LED status light stays lit. On the instruction manual it says that the unit was not powered up correctly and to contact NI. The controller used to work fine until we had a short on the mains side of the power supply The AI, AO and thermocouple modules did not power up but the DI and DO modules seemed to be getting power. Is there anything we can do or just send it back for repairs. When I replaced the controller with another one, the system worked fine and the status LED turned off after a few seconds.
rgds
Inzaghi_2

Sounds like you've proven that the controller is bad. Next step is an RMA from NI. Make sure NI tells you what failed in the controller and see if they will comment on what might have caused it. The idea being to see if you can do anything to prevent this failure in the future.

Apple TV Status LED is Flashing

It hasn't been plugged in a couple months. Just plugged it in and the Status LED keeps flashing. First thought that it may be receiving updates, but it's been ongoing for 15+ minutes. Tried powering it down and back up again a couple of times, but same thing happens. The TV only shows a graphic of the HDMI cable hookup, no menu options...
Anyone know about other options to try, or been here before?

You have to grab a micro usb cable and restore via iTunes
http://support.apple.com/kb/HT4367?viewlocale=en_US&locale=en_US

How to read the power and status LEDs on cFP2020

Can the cFP2020 Power and Status LEDs be monitored by a host program? Also, can the Power and Ready LEDs be monitored from the other cFP Modules?

You can not directly read the Network Module Power or Status LED from a host program. Likewise, you can not directly read the Power and Ready LED of an IO module.
However, even though you can not directly ready the LED status, there are ways of finding out most of the information that the LEDs convey.
For the Network Module Power LED, you can infer the status of the Power LED by looking at the channel status for any/all items that are on the bank. If the items have errors indicating that a communication timeout has occured or an addressed item does not exist, then it is probable that the unit is offline (either because of no power or a fault). The Status LED indicates the current operating status of the Network module and in most cases, if it is flashing
, then a fault has occured that shutdown the processor. In most cases, you will not be able to determine that the Status LED is flashing, as the Status LED indicates a fault condition which will put the unit into a non-standard operating mode (e.g. firmware corruption, unassigned IP Address, or an OS fault).
For the IO modules, each channel on a module can report status, and based upon the status you can infer the state of the LEDs. If the module does not have the Power LED lit, the most likely status will be "Addressed item does not exist". If the module has the Power LED but no Ready LED, then the status will indicate that the "item is unconfigured". If the module has both a Power and Ready LED, than the channel should report either a good status, or a channel specific error (if applicable).
Regards,
Aaron

WiSM Status LED 1 & Status LED 2 showing off. Is it normal?

Hi,
WiSM WLAN Service Module WS-SVC-WISM-1-K9 in 6509e running VSS IOs s72033-ipservicesk9_wan-mz.122-33.SXI2a.bin having trouble to get the IP from service-vlan DHCP also status LED 1 & Status LED 2 showing off.
The pertinent config is as follows.
vlan 300
name WiSM_Service_Vlan
interface Vlan300
description *** WiSM Service-Vlan
ip address 192.168.200.1 255.255.255.0
ip dhcp excluded-address 192.168.200.1
ip dhcp pool WiSM_Service-Vlan_300
   network 192.168.200.0 255.255.255.0
   default-router 192.168.200.1
wism service-vlan 300
vlan 183
name WiSM_Management
interface Vlan183
description *** WiSM Management Vlan ***
ip address 10.39.139.254 255.255.255.0
wism switch 1 module 4 controller 1 allowed-vlan 125,126,183,300
wism switch 1 module 4 controller 2 allowed-vlan 125,126,183,300
wism switch 2 module 4 controller 1 allowed-vlan 125,126,183,300
wism switch 2 module 4 controller 2 allowed-vlan 125,126,183,300
wism switch 1 module 4 controller 1 native-vlan 183
wism switch 1 module 4 controller 2 native-vlan 183
wism switch 2 module 4 controller 1 native-vlan 183
wism switch 2 module 4 controller 2 native-vlan 183
HO2NET0001#sh wism status
Service Vlan : 300, Service IP Subnet : 192.168.200.1/255.255.255.0
      WLAN
Slot Controller Service IP       Management IP    SW Version Status
----+-----------+----------------+----------------+-----------+---------------
20    1           0.0.0.0          0.0.0.0                      Service Port Up
20    2           0.0.0.0          0.0.0.0                      Service Port Up
HO2NET0001#sh module
Mod Ports Card Type                              Model              Serial No.
1    8 CEF720 8 port 10GE with DFC            WS-X6708-10GE      SAL13442Q5N
2    8 CEF720 8 port 10GE with DFC            WS-X6708-10GE      SAL13442GAL
3   48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX     SAL13410N8P
4   10 WiSM WLAN Service Module               WS-SVC-WISM-1-K9   SAD133101UY
5    5 Supervisor Engine 720 10GE (Active)    VS-S720-10G        SAL13442JE4
Mod MAC addresses                       Hw    Fw           Sw           Status
1 0025.84f1.55b8 to 0025.84f1.55bf   2.1   12.2(18r)S1 12.2(33)SXI2 Ok
2 0025.84f1.4e58 to 0025.84f1.4e5f   2.1   12.2(18r)S1 12.2(33)SXI2 Ok
3 0027.0da7.c240 to 0027.0da7.c26f   3.2   12.2(18r)S1 12.2(33)SXI2 Ok
4 0023.5e25.7168 to 0023.5e25.7177   2.3   12.2(14r)S5 12.2(33)SXI2 Ok
5 001f.9e2a.2608 to 001f.9e2a.260f   3.1   8.5(3)       12.2(33)SXI2 Ok
Mod Sub-Module                  Model              Serial       Hw     Status
1 Distributed Forwarding Card WS-F6700-DFC3C     SAL13442EG9 1.4    Ok
2 Distributed Forwarding Card WS-F6700-DFC3C     SAL13442H9T 1.4    Ok
3 Centralized Forwarding Card WS-F6700-CFC       SAL13442HU9 4.1    Ok
4 Centralized Forwarding Card WS-SVC-WISM-1-K9-D SAD133200D6 2.1    Ok
5 Policy Feature Card 3       VS-F6K-PFC3C       SAL13442E5S 1.1    Ok
5 MSFC3 Daughterboard         VS-F6K-MSFC3       SAL13421AJZ 2.0    Ok
Mod Online Diag Status
1 Pass
2 Pass
3 Pass
4 Pass
5 Pass
HO2NET0001#sh vlan
300 WiSM_Service_Vlan                active    Gi1/4/9, Gi1/4/10
The service IP is supposed to have been populated with an address from the dhcp pool. I am also unable to connect to access it by console as well as doing a session switch 1 slot 4 processor 1. I get the following upon attempting to do so:
Through Console.
It is giving following & then got stuck.
Bootloader 3.2.202.0 (Nov 13 2007 - 19:35:12)
Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200020
        CPU: 999 MHz
        CCB: 333 MHz
        DDR: 166 MHz
        LBC: 41 MHz
L1 D-cache 32KB, L1 I-cache 32KB enabled.
I2C:   ready
DTT:   1 is 33 C
DRAM: DDR module detected, total size:512MB.
512 MB
8540 in PCI Host Mode.
8540 not PCI Arbiter.
Memory Test PASS
FLASH:
Flash Bank 0: portsize = 2, size = 8 MB in 142 Sectors
8 MB
L2 cache enabled: 256KB
Card Id: 1537
Card Revision Id: 1
Card CPU Id: 1287
Number of MAC Addresses: 32
Number of Slots Supported: 4
Serial Number: FAM133200D6
Manufacturers ID: 30464
Board Maintenance Level: 00
In:    serial
Out:   serial
Err:   serial
                      .o88b. d888888b .d8888. .o88b. .d88b.
                     d8P Y8   `88'   88' YP d8P Y8 .8P Y8.
                     8P         88    `8bo.   8P      88    88
                     8b         88      `Y8b. 8b      88    88
                     Y8b d8   .88.   db   8D Y8b d8 `8b d8'
                      `Y88P' Y888888P `8888Y' `Y88P' `Y88P'
                    Model SVC-WiSM   S/N: FAM133200D6
Net:   TSEC ETHERNET
IDE:   Bus 0: OK
Device 0: Model: STI Flash 8.0.0 Firm: 01/17/07 Ser#: STI1MMJ109198093647
            Type: Removable Hard Disk
            Capacity: 488.7 MB = 0.4 GB (1000944 x 512)
Device 1: not available
Booting Primary Image...
Press <ESC> now for additional boot options...
Detecting Hardware . . .
Cryptographic library self-test....passed!
XML config selected
Validating XML configuration
Cisco is a trademark of Cisco Systems, Inc.
Software Copyright Cisco Systems, Inc. All rights reserved.
Cisco AireOS Version 5.2.178.0
Initializing OS Services: ok
Initializing Serial Services: ok
Initializing Internal Interfaces: ok
Initializing Network Services: ok
Initializing Licensing Services: ok
Starting ARP Services: ok
Starting Trap Manager: ok
Starting Network Interface Management Services: ok
Starting System Services: ok
Starting FIPS Features: ok : Not enabled
Starting Fast Path Hardware Acceleration: ok
Starting Switching Services: ok
Starting QoS Services: ok
Starting Policy Manager: ok
Starting Data Transport Link Layer: ok
Starting Access Control List Services: ok
Starting System Interfaces: ok
Starting Client Troubleshooting Service: ok
Starting Management Frame Protection: ok
Starting LWAPP: ok
Starting CAPWAP: ok
Starting Certificate Database: ok
Starting VPN Services: ok
Starting Security Services: ok
Starting Policy Manager: ok
Starting Authentication Engine: ok
Starting Mobility Management: ok
Starting LOCP: ok
Starting Virtual AP Services: ok
Starting AireWave Director: ok
Starting Network Time Services: ok
Starting Cisco Discovery Protocol: ok
Starting Broadcast Services: ok
Starting Logging Services: ok
Starting DHCP Server: ok
Starting IDS Signature Manager: ok
Starting RFID Tag Tracking: ok
Starting WLAN Control Protocol (WCP): ok
Starting Mesh Services: ok
Starting TSM: ok
Starting CIDS Services: ok
Starting Ethernet-over-IP: ok
Starting DTLS server: enabled in CAPWAP
Starting FMC HS: ok
Starting WIPS: ok
Starting SSHPM LSC PROV LIST: ok
Starting Management Services:
   Web Server: ok
   CLI: ok
   Secure Web: Web Authentication Certificate not found (error). If you cannot access management interface via HTTPS please reconfigure Virtual Interface.
(Cisco Controller)
Welcome to the Cisco Wizard Configuration Tool
Use the '-' character to backup
Would you like to terminate autoinstall? [yes]:
AUTO-INSTALL: starting now...
Through Session
HO2NET0001##session switch 1 slot 4 proc 1
The default escape character is Ctrl-^, then x. You can also type 'exit' at the remote prompt to end the session Trying 0.0.0.0 ...
Any assistance or ideas offered will be greatly appreciated.
Thanks,

Hi Tabish,
How many times do you have to open this same topic?
In my opinion, this is your THIRD thread for the same topic.

FP-1600 Status LED blinks 17 times.

My FieldPoint bank has 9 modules. I previously had a problem with the FP-TB-10 power and ready lights blinking, but that was because one of my dual-channel modules was not seated correctly. Now the status LED is blinking 17 times. The manual says to contact NI about this. The FieldPoint Explorer seems to find all of the modules correctly, though. Anyone know what's up?

Aaron,
I checked the firmware and the FieldPoint Explorer version, and I'm using 3.20 and 3.0, respectively. When I power cycle the FP-1600, the 17 blinks of the status LED go away. Communication works, and all of the devices are found. However, communication does drop out from time to time, and eventually the status LED begins blinking 17 times again.
A possibly related issue is that the FP-AI-V10 dual-channel module that I have plugged into slot 2 of the FP-TB-10 base causes the FP-TB-10 to flash its power and ready LEDs. Re-seating the FP-AI-V10 seems to fix this, although the module is definitely already clicked into place when I see this problem. Upon reseating (or just pressing on it without removing the module), the FieldPoint Explo
rer program finds this module.
I'm tempted to think that this issue with the FP-TB-10 and FP-AI-V10 are unrelated to the FP-1600's status LED blinking 17 times because even with the FP-TB-10 removed from the bank, I still get the flashing LED.
Any ideas? Also, what is a GPF type error?
Thanks,
Jake

CFP-2110 will only boot into safe mode + communication error?

Hello all,
I have a new cFP-2110 and I'm trying to configure it. I'm using Realtime 8.0, Fieldpoint drivers 5.1.2 on WIndows XP. My host computer versions match the FP controller software version and the safe-mode dip switch is in the 'off' position.
I even re-formatted the controller memory (like someone suggested in a different thread) but I keep getting the same thing: Connected - Safe Mode (Improper Installation)
Attached is a screen shot of the error I get when I try to 'find devices.' I have a good ethernet connection (although I have a yellow blinking LED on the RJ45 of the controller but not the green). I know this because I can reboot the controller from the host - It just always reboots into safe-mode. Does anybody have any suggestions for me?
Thanks - Paul
Attachments:
cFP-2110 error.JPG ‏365 KB

I finally found the problem and thought I'd share in case anyone else has similar issues:
In troubleshooting I wanted to eliminate network communication errors so I decided to connect directly to my host PC. I got a crossover ethernet cable and connected straight to my host PC's ethernet card. I had to log in as administrator on the host in order to change it's IP address to a static address. Then I re-formatted the FP controller, re-assigned it's IP and finally re-installed the RT and FP drivers. Finally - I had a normal connection!
This made me wonder if it was being directly connected to the host or being logged in as an administrator that was the fix. So I went to a second host PC, logged in as administrator (leaving it as a normal network connection), reformatted my second controller and re-installed the software - and hot damn - it worked!
Moral of this story is - be logged in as admin. before attempting to install any software...

Charge status LED bug in new firmware

After updating my 2nd generation iPod shuffle firmware from version 1.0.2 (which it came with) to version 1.0.4, the status LED does not correctly indicate when the battery is fully charged anymore.
According to the manual, the status LED should turn from yellow to green only after the battery has been fully charged, which takes about four hours if the battery was completey depleted. It worked that way with the original firmware.
Now with firmware 1.0.4, the LED turns to green after a little less than 90 minutes of charging the empty battery, which by then obviously isn't full yet. From runtime tests I conducted it seems that the battery has reached about 85% charge at this point.
So if you want to ensure a full charge, ignore the LED and charge the iPod shuffle for at least four hours until Apple fixes this issue.

I went to local Nokia service, and they told me that probably it was wrongly flashed. So I reinstalled firmware two more time, but it always have the same problem. Is there someone with 6300 that have the newest firmware and can test this ?
thank you
I will put this phone to service and see what they will do.

Problem Cisco AIR-LAP1131AG-E-K9 Ethernet LED = Off; Radio LED = RED ; Status LED = RED ;

hi,
I have a Cisco AIR-LAP1131AG-E-K9 when I boot one accesspoint it gives Ethernet LED = Off; Radio LED = RED ; Status LED = RED and only next listing in the screen:
Xmodem file system is available.
Flashfs[0]: unable to allocate available block.
The system has been interrupted, or encountered an error during initializion of the flash filesystem.
The foolowing commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init
ether_init
tftp_init
boot
When I type this commands, it doesn't help at all. The output will be following:
ap: flash_init
Initializing Flash...
flashfs[0]: out of memory
...done Initializing Flash.
ap: ether_init
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ap: tftp_init
Unable to get our ip address: no "IP_ADDR" variable set
ap: boot
Loading ""...; permission denied
Error loading ""
Interrupt within 5 seconds to abort boot process.
Boot process failed...
ap:
what i do ? please help , thanks

Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12154826/problem-cisco-air-lap1131ag-e-k9-ethernet-led-radio-led-red-status-led-red

CFP 2110 - Status led flashing continously

Similar Messages

Maybe you are looking for