CFP status led - stays lit solid red!

Hi,
I have a problem with a cFP-2120 RT controller where the red LED status light stays lit. On the instruction manual it says that the unit was not powered up correctly and to contact NI. The controller used to work fine until we had a short on the mains side of the power supply The AI, AO and thermocouple modules did not power up but the DI and DO modules seemed to be getting power. Is there anything we can do or just send it back for repairs. When I replaced the controller with another one, the system worked fine and the status LED turned off after a few seconds.
rgds
Inzaghi_2

Sounds like you've proven that the controller is bad. Next step is an RMA from NI. Make sure NI tells you what failed in the controller and see if they will comment on what might have caused it. The idea being to see if you can do anything to prevent this failure in the future.

Similar Messages

FP2015 status led stay lit

While turning on the system the status led stay on. Doing this few time, now the Status led doesn’t stay on but it seems that the controller doesn’t make the booting procedure (the Leds doesn’t turn on and off at the begging)

This issue can generally be solved by formatting the internal Compact FLASH memory on the controller. There is a < a href="http://digital.ni.com/public.nsf/websearch/6D0F9F74FD2DAD0186256EE5007198D4?OpenDocument">Knowledge Base that describes in detail how to format the controller. Sometimes you will first have to switch both the Safe Mode (switch 7) and Reset IP (switch 8) dip switches and cycle the power to first get the controller into a safe state.
The Compact FLASH corruption is generally due to losing power while writing to a sector on disk. This can cause that sector as well as other adjacent sectors to become corrupt.

FP2000 status light stays lit red can not communicate

I just tried to update the software on a FP2000 not the status light stays read and can not communicate. any ideas.
Solved!
Go to Solution.

TJE-
Based on the manual for this device, the status light staying lit refers to “the FieldPoint-20XX did not power on correctly.” I would suggest removing all software from this controller and reinstall it.
Regards,
Mike S
NI AE

1131AG - LED ring is solid red

Hello.
I appreciate anyone who can answer this question. I'm writing from a high school in Detroit, Michigan.
We have a Cisco Aironet 1131AG access point that broadcasts to our gym for parent meetings, etc.
Recently this device has stopped transmitting. No one can pick up a wireless signal. The LED ring is solid red.
I took it to my office and plugged it in, and the ring is still red.
The user's guide doesn't have any reference to this problem, and I couldn't find it on the Cisco website.
Could it have been hit by a power surge, or do you think it's something else?
Many thanks,
Ed Morykwas

Okay, I tried it but I don't think it worked. Here's what I did...
1. Unplugged the ap.
2. Downloaded and installed Hyperterminal Private Edition 7.0. on my computer.
3. Launched the program.
4. Pulled down the File menu and clicked New Connection. I gave the name "Cisco" to the new connection.
5. Click the Configure button and verified that the settings were 9600 8-N-1.
6. Connected a CAT5 cable from the Console port of the ap to the Ethernet port on the back of my computer.
7. Plugged in the power of the ap.
Nothing happened. No writing appeared on the screen.
The LED ring is still solid red. The small Ethernet LED light is also solid red. The small Radio LED light is a mixture of red and yellow.
I've never used Hyperterminal before. Did I miss something?

IPS status LED stays red

Dear Friends,
There is a IPS 4260 that reports the status LED to red. When reading the hardware installation guide, i came to know that this indicates a POST failure. I forced a POST again of the IPS by rebooting the IPS but i could not capture any significant error.
However, i am enclosing the captures of the boot process (Filename: IPS) and the sh tech-support (Filename: IPS Tech support).
Can you please help me on this?
Thanks a lot
Regards
Gautam

Shutdonw the IPS for 5 - 10 Minutes and the Restart i did and the issue has been resolved .
Thanks,
Mustafa

Hp Pavilion 750n just beeps and LEDs stay lit

My Hp Pavilion was on Saturday and now it just beeps every 2 seconds and the LEDs stay it and it never shuts off. And there is no video to the monitor. Can someone help me????
This question was solved.
View Solution.

If the XP machine is still functional, you can use the Easy Transfer XP to WIN7 or WIN8. In either case, the WIN8 link is a great read, as it covers a tutorial for WIN7 and 8. Easy Transfer Cable for the computers.
This simple device can be used to copy your folders (documents, picture, music) to another computer.
The following document, with videos, will assist you in removing the hard drive.
I am a volunteer. I am not an HP employee.
To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
(2) HP DV7t i7 3160QM 2.3Ghz 8GB
HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
Both Customs use Rosewill Blackhawk case.
Printer -- HP OfficeJet Pro 8600 Plus

AEBS: Status LED stays green even if modem unplugged?

I recently updated to 7.6.3. and since than have had loads of problems. I'm not sure if it's just coincidence or if they are 7.6.3. related. Problems included difficulty connecting to internet, slow wifi speeds and being unable to see the AEBS under Airport Utility on a Macbook (Mountain Lion 10.8.2) unless the device and Mac were rebooted. It would often then dissapear again. I've resolved most of those now by going back to 7.6.1. There is one more issue that I've noticed though that didn't seem to happen before.
Essentially, amidst all the testing and rebooting I was doing I noticed that when the modem (handling the PPPoE with the Airport in bridge mode - forced to this because my ISP does not play nice with Apple's PPPoE authentication) was unplugged or powered down, the green status light on the airport stayed on? I'm sure it never did this before, indeed I've seen the amber light on when there have been ISP outages. One thing I haven't tried yet is leaving the modem off for an hour or so to see if that prompts a change to amber.
As yet I haven't done another full factory reset (albeit one was done to get it all working again).as I've wasted two days with the 7.6.3 update and needless to say I need a break from the thing!!! Just strikes me as odd that despite the internet light on Airport Utility on all the devices shows amber when the ethernet cable is unplugged from the modem yet the green light on the BS stays on AND, under Aiport Utility 5.6 it shows a green light against the airport saying status is 'Normal'?
Surely this should not be happening? No internet, amber light on AEBS I would have thought?

Thanks. I'll have a look maybe over the weekend. I know resets are not that complex (albeit I did have loads of problems getting the AEBS to even show again when I did a reset under 7.6.3 when the problems started) but I spent so long sorting the mess out I need to get on and do things ON the internet for a couple of days, rather than trying to get it working LOL!!
I notice you say AU 5.6.1, the version I have other than 6 is 5.6. That wouldn't be causing any issues would it. One thing I did try to do when it was all completely screwed is use 5.6 to configure manually. I now seem to have various .XML profiles under
User/Library/Application Support/Apple/Airport/Configuration
My undesrtanding is that AU doesn't work this was and that these folders/files shouldn't be there? Maybe I'm wrong? Are they just profiles under my user name that won't be affecting anything. Or could they be interfering with AEBS operations and / or warnings in any way. Is the AEBS confused? I was tempted to delete the entire airport folder altogether or even just the config settings then do a factory restore of the AEBS under 5.6. Trouble is I'm not sure which AU Airport folder above belongs to (e.g. will it screw things up further if I delete any or all of it). Bit of a mess really
Yes the settings you mention are correct, the IP addess even picks up at 101, the resrved address on the router.

ASUS P6X58D Memory OK (MEMOK!) issue DRAM LED Stays solid red.

HI
This morning when I turned on my computer, it would not boot. Not even the most basic boot (I could not get to the ASUS bio DOS screen, for example).   It would only sound one beep, and then finally a second beep-- but the second beep did not sound immediately thereafter. . Usually, I recall, I hear two rapid beeps almost immediatley when I boot up.
I did some checking on the net. It appears to be a memory issue. I reset my memory in their slots. But that did not help.
I saw the on the ASUS motherboard the DRAM LED light was solid red. After checking the manual (and checking some YouTube videos), I pressed the MEMOK! button right next to the DRAM LED light.
According to the manual, when using WIndows OS the system will reboot as it does its "Flashing lights" test to try to use a memory failsafe setting. However, even after reboot the red light stayed solid and appeared not to do the testing.
Perhaps I am not doing the test correctly. For example, do I keep my finger on the MEMOK! button throughout the tests and reboots?? Or just press once, and never press it again.
ASUS USA support appears to be closed today for the New Year's holiday. So I am wondering if anyone here has some suggestions. My memory was working fine up until this morning.
I suppose I could wait until tomorrow when ASUS phone support is live again, but thought someone might have some suggestions / tests I can do today.
Thanks
Rowby

Well I fixed it.
Not sure exactly what I did that fixed it, but here is what I did.
1) I unplugged the computer.
2) I disconnected the power supply from the motherboard.
3) I removed the battery.
4) I let it sit for about an hour.
5) I pushed the motherboard reset button on the back of my computer (I perhaps should have done this first, but I did it.)
6) I put a new battery into the motherboard (perhaps the old one was dead or a zombie.)
7) I reconnected the power supply to the mother board.
8) I plugged in the box.
9) I heard the familiar two beeps, and sure enough the unit booted up.
Upon bootup the ASUS screen had me to into bios and double check everything.   Then it all rebooted again, and opened windows 7.
I will make sure I have the lastest ASUS bios. But I see that it is recognizing all 24 GB of memory, so I guess I am good to go.
Rowby

PM8M-V no beep no boot Solid Red LED

I've had the PC I've been using for about 2.5 years, no problems.
Last week a lightning storm killed all the AGP/PCI functionality of my old motherboard. At first, I thought it killed my AGP video card because the internal video to the old motherboard worked fine. This is where I decided to buy an MSI PM8M-V from CompUSA.
Tried installing the board today. I literally just powered down the PC with the OLD Board in it and it all was working fine. The two motherboards seem to be similar in quality and both have internal sound and video.
With the new motherboard hooked up when I press Power the CPU fan comes on, and the LEDS on the front of the tower come on. The RED LED [Which I believe is the HDD LED, will have to double check] comes on and stays lit. After about 20 seconds or so the system powers down. I get no beeps or anything. I doubt any of the components are bad because they were all just working 1 hour ago.
Does this point to a specific problem? I don't think the CPU is overheated as I have thermal paste the Heatsink fits snug.
Suggestions?

Ok, an update.
I have an Antec PSU 300W that appears to be working well.
At the moment I have 1gig of unknown brand DDR memory
I have a P4 Prescott 3.0GHz [I don't recall any of the other details as this PC is several years old]
All hardware pulled from a perfectly working system with the exception of an AGP slot on the old motherboard.
The old motherboard has nearly the exact same features and appears to be of very comparable quality.
I hooked the old motherboard up with the processor, memory, and same PSU and it booted to the BIOS just fine.
This new MSI motherboard WILL NOT boot to the BIOS with the exact same equipment installed. I have double and triple checked.
Is there anything else I should do before contacting CompUSA for a return. I've seen some recommendations about jumping pins to clear the CMOS or something.

HELP! BB Pearl 8130. Solid Red Led Light. Won't go away.. HELP!

My LED has turned a solid Red color. It's on all the time and is only off when I pull the battery out. My phone does still charge. I've done everything to get rid of it even wiping my blackberry and upgrading the software. I read something about Blackberry Music Gateway? I do use my pearl to listen to Pandora everyday and iheart radio with a 3.5 cable that plugs into the dash of my truck, but it never did this before. Any help would be greatly appreciated!
Thanks!
Justin

Justin, so you've wiped the device completely and reloaded a new OS... still does the same. Anytime the BlackBerry is powerd on, the LED lights up RED?
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Sup V with 4507R status led in Red

Hi,
I carried out an upgrade in 4507R with 2 sup V, I loaded in both card 12.2(53)SG10 and I confirmed the redundancy is working
I don't understand why both status led (for Sup V) are in red.
the loggs do not show error , any idea how can I identify the reason of red color in status led?
regards
Mod Redundancy role     Operating mode      Redundancy status
----+-------------------+-------------------+----------------------------------
1   Standby Supervisor SSO                 Standby hot
2   Active Supervisor   SSO                 Active
redundancy
mode sso
main-cpu
auto-sync standard

Hello,
The status LED can actually lend useful information regarding the potential culprits to your issue. You can check out the STATUS LED Error Indications in the 1601 User Manual.
In this case, it looks like you should contact National Instruments directly since it seems as though the module did not power on correctly. You may have to return your unit for replacement or repair.
Cheers,
Emilie K. | Applications Engineer | National Instruments

CFP 2110 - Status led flashing continously

I'm running into problem with a cFP 2110.
During the debugging of my RT application on the cFP, I get an error message "Host IP address not in the access list". At this time, I was unable to download any application to the cFP. the VI server IP access list was configured with *. So all the IP address can access to the cFP.
I found a procedure on the ni web site to reset the system.
-Set to safe mode
-ftp the cFP and delete all the file
-Remove the safe mode.
It means that there is no more OS or LabVIEW RT on the system.
Now, When I restart the cFP, the Status led is flashing continously (1 flash / 1.5s) and I don't have access anymore to the cFP in MAX.. Can some one help me on this case ? .
Thanks
Attachments:
Ni_recommendations.pdf ‏126 KB

Hi Poussin,
I would recommend flipping the Reset IP dip switch (dip switch 7). This
should get the controller to show up in Measurement and Automation
Explorer(MAX) as 0.0.0.0. If you can't see the controller, you may want
to try turning off your firewall. Often computer firewalls will prevent
customers from seeing unconfigured controllers in MAX.
Once you find your controller, you can flip the reset IP dip switch back to the
off position and reset the IP address. For more information on this,
click on your FieldPoint controller in MAX that will be displayed as
0.0.0.0. In the MAX help that appears on the right, click on the link
titled, "Configure Network Settings." If you need assistance
choosing an IP address, please look at this KnowledgeBase.
Once you have assigned an IP address to the controller, the status light should
stop blinking once. You will then need to install software.
Here is a general
document that describes how to assign an IP address and install software.
Please let me know if you have any other questions.
Regards,
Ching P.
DAQ and Academic Hardware R&D
National Instruments

FP 1601 status led shows red continuously

I am trying to use FP 1601 which was already configured long before. But now the status LED is continuously red .Power LEd is green and all other LEds are off. Am giving 24V power and checked that it is given to V and C properly .Ethernet connection is also proper. i tried to reset , but could not. i cant use it in anymore. can anyone help in troubleshooting

Hello,
The status LED can actually lend useful information regarding the potential culprits to your issue. You can check out the STATUS LED Error Indications in the 1601 User Manual.
In this case, it looks like you should contact National Instruments directly since it seems as though the module did not power on correctly. You may have to return your unit for replacement or repair.
Cheers,
Emilie K. | Applications Engineer | National Instruments

Problem Cisco AIR-LAP1131AG-E-K9 Ethernet LED = Off; Radio LED = RED ; Status LED = RED ;

hi,
I have a Cisco AIR-LAP1131AG-E-K9 when I boot one accesspoint it gives Ethernet LED = Off; Radio LED = RED ; Status LED = RED and only next listing in the screen:
Xmodem file system is available.
Flashfs[0]: unable to allocate available block.
The system has been interrupted, or encountered an error during initializion of the flash filesystem.
The foolowing commands will initialize the flash filesystem, and finish loading the operating system software:
flash_init
ether_init
tftp_init
boot
When I type this commands, it doesn't help at all. The output will be following:
ap: flash_init
Initializing Flash...
flashfs[0]: out of memory
...done Initializing Flash.
ap: ether_init
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ap: tftp_init
Unable to get our ip address: no "IP_ADDR" variable set
ap: boot
Loading ""...; permission denied
Error loading ""
Interrupt within 5 seconds to abort boot process.
Boot process failed...
ap:
what i do ? please help , thanks

Duplicate posts.
Go here: http://supportforums.cisco.com/discussion/12154826/problem-cisco-air-lap1131ag-e-k9-ethernet-led-radio-led-red-status-led-red

MDS 9216 - showing red status LED, not starting up

Hi,
In a recent power loss (took out our R&D UPS in the process), an MDS 9216 we have in R&D failed.
On power up, it shows a red status LED, and does nothing. We've pulled and swapped PSUs (something we're told is a common fix for a common problem with these chassis), to no avail.
Strangely, we pulled the fan card (which had a green light), and put it back in to see it now also has a red status light.
We've swapped all cards around for new and spares (even the main cards) and they show up with red status lights in the chassis (can't test them in another chassis at present) so I assume this problem is with the chassis itself (ie the backplane or PSUs).
Any ideas, any similar experiences?
Many thanks,

As far as warranty, it would be covered for 1 year or 90 days from purchase....not sure which, but since the 9216 is end of sale for a few years now, I doubt that is covered under warranty. If you have a maintenance contract covering that 9216 serial number, then it would be covered. The design on the 9216 is that the module 1 is not field replaceable. There is no Cisco part number for the slot1 line card. It is a hybrid of a 16 port FC module with a supervisor daughter card. It is basically considered part of the chassis. If you have your own spare 9216 and feel energetic you could replace the slot 1 line card....but from the official support perspective, it is not replaceable.
There are no other replaceable parts besides the chassis and PS that would cause this problem. (I assume you have removed any line card from slot2 to be sure it was not causing the problem).
Thanks,
Mike

CFP status led - stays lit solid red!

Similar Messages

Maybe you are looking for