Change Audit Prime Infrastructure 2.0

When looking at reports: Reports > Compliance > Change Audit
I only receive Inventory Reports with the user name System(which is not benefical).  Is there any way to obtain 24 hour Change Reports?
Thanks
CG

Hi,
I know this feature is there is LMS ,where you can configure the AUTOMATED Action based on Syslogs to get an Alert for config change or any other changes ,however I do not see this option available in PI  2.0.
Syslogs are not compltely supported in 2.0 but in PI 2.1 we should have the complete support for syslogs.
Thanks-
Afroz
[Do rate the useful post]

Similar Messages

  • Configuration Change Audit Report in Prime Infrastructure 2.1

    Is there any plan to implement a Configuration Change Audit report in future releases of Prime Infrastructure (ie. 2.2)?  When I go into the Reporting area and run a Change Audit report under the Compliance section it doesn't give me any information in regards to configuration changes, only inventory changes.  There are managers who would like the ability to receive an e-mailed report of configuration changes within a 24 hours period.  Currently the only way I can tell that you can get this information is by logging into Cisco Prime and going to Network Audit under Operation / Device Work Center.
    Thanks,
    Brian

    Configuration Change Management (with Baseline Compliance reporting) is projected for the next release after 2.2. As of now that's projected to be ca. April 2015.
    On a side note, last I heard, 2.2 should be out in the next couple of weeks.

  • Prime Infrastructure 2.0 - Alert on Switch Config Change

    We are in the process of testing out Prime Infrastructure 2.0, is there a way to get an alert when a device's configuration has changed, and send out what has changed in email? I have scheduled Config Archiving for all of my devices, and i can see the config differences when a changes is made in the Prime GUI, but we currently use Kiwi CatTools to send out emails that show what devices had configuration changes and what those changes were, it would be nice if Prime would do that so we could do away with that service. I have looked through all of the reports but do not see anything.

    Hi,
    I know this feature is there is LMS ,where you can configure the AUTOMATED Action based on Syslogs to get an Alert for config change or any other changes ,however I do not see this option available in PI  2.0.
    Syslogs are not compltely supported in 2.0 but in PI 2.1 we should have the complete support for syslogs.
    Thanks-
    Afroz
    [Do rate the useful post]

  • Cisco Prime infrastructure Change severity Switches and hubs - link down alarm

    Hi, I want to change the severity of the link down alarm in the Cisco Prime Infrastructure 1.3, but in the menu Administration -> System Settings -> Severity Configuration i can not find the alarm. Some body knows where is it? o where i can change the severity of that alarm?
    Thanks in advanced.

    Hi Rollin and Daniel,
    the first test i did changing the severity was with a new installation, with no devices added and it worked, when i did it in a Prime infrastructure with devices added it didn´t work, well, for this Prime with devices i upgraded it with the patch for 1.3 version and now it works too, the alarms is ok as the alarm severity, this is the link for the patch:
    http://software.cisco.com/download/release.html?mdfid=284652876&flowid=38562&softwareid=284272933&release=1.3.0&relind=AVAILABLE&rellifecycle=&reltype=all
    i hope this helps,
    Regards,
    Milton Tizoc.

  • Prime Infrastructure - Automating the change "mac@ - AP name" with CSV file

    Hi,
    We are going to deploy a lot of new LAP. For each site our  customer will give us an excel file with the MAC @ of the AP and the  target name.
    I was wondering if it was possible to automate the  injection of this file "mac <-> ap name" and then apply the  predefined template with P.I ?
    If yes, could you explain how, as I am new to Prime Infrastructure.,The goal is to avoid to rename each AP individually on prime as there is a lot of AP to deploy.
    Many thanks in advance !
    Oliv.

    Hi Oliv:
    In the Classic View of Prime Infrastructure, under Configure > Access Points, there's a menu option for Import AP Config.  This uses a .csv file to match APs by the MAC address and make changes in bulk.  From the online help:
    Sample File Header:
    AP Name,Ethernet MAC,Location,Primary Controller,Secondary Controller,Tertiary Controller
    ap-1, 00:1c:58:74:8c:22, sjc-14-a, controller-4404-1, controller-4404-2, controller-4404-3
    The CSV file can contain following fields. AP Ethernet MAC Address is mandatory, Optional fields are           AP Name, Location, Primary Controller, Secondary Controller and Tertiary Controller.            
    Optional fields can be empty. AP Config Import will  ignore empty optional field values. However, if Primary Controller and  Secondary Controller entries are empty then Unified AP update is not  done
    Ethernet MAC: AP Ethernet MAC Address
    AP Name:AP Name
    Location:AP Location
    Primary Controller:Primary Controller Name
    Secondary Controller:Secondary Controller Name
    Tertiary Controller:Tertiary Controller Name

  • Change Interface availability threshold from Cisco Prime Infrastructure 2.0

    Dear Community,
    I’m working in Cisco Prime Infrastructure 2.0 and I’m having the following problem:
    I want to monitor the interfaces availability from all the devices of my network. But only makes sense send an email notification  for the most critical interfaces. I don´t want to receive an email notification every time anyone unplugs the network wire.
    How can I achieve this?
    I already tried to change the interface availability threshold from the Interface Health Threshold Template, but this one isn´t available to configure.
    The idea was to change the severity of the alarm so I could distinguish what type of alarm would send email notification.
    I also created a Custom SNMP Template that gets the ifOperStatus using the MIB IF-MIB. This also didn’t work because Prime Infrastructure doesn’t allow me to define thresholds to a Custom SNMP Template.
    Without threshold, no alarm, without no alarm, no email notification!
    Can you help?
    Regards,
    Daniel CJ

    Only on the HA pair which would be the secondary.
    High Availability (HA) RTU: If Cisco Prime Infrastructure is deployed in a high availability configuration with one primary and one secondary instance in an HA pair, then an HA RTU is required. You only need to purchase a single set of the regular licenses (for example, Base, Lifecycle, and so on) for the primary instance.
    Thanks,
    Scott
    Help out other by using the rating system and marking answered questions as "Answered"

  • URGENT---cisco prime infrastructure 1.2. change default theme

    hello guys,
    I wanted to ask you a question.
    I have installed in my company the cisco prime infrastructure 1.2.
    As you know, the lifecycle theme  has enough bugs, but these bugs are overtaken if we use the classic theme.
    I have several users working with cisco prime infrastructure 1.2, and i was wondering if it is possible to define classic theme as default for all people.
    thnks

    I would think if they logged in they can change their own preference. You only can change it from the account you logged in as.
    Sent from Cisco Technical Support iPhone App

  • Upgrade Cisco Prime LMS 4.0 to Cisco Prime Infrastructure 2.1

    My company has asked me to migrate Prime LMS 4.0 to Prime Infrastructure 2.0 for a client and can not find the guide, the questions are? the migration is possible without an intermediate step? and There is a guide to update LMS 4.0 to PI 2.0 ??
    Thanks in advance.

    Prime LMS 4.2.2 added support for the PI template directly:
    Export Data for Prime Infrastructure
    Cisco Prime LAN Management Solution supports data migration to Prime Infrastructure 1.2. This feature enables user to export the Device Credentials Repository (DCR) data from LMS 4.2.x versions to Prime Infrastructure 1.2. The data backup status and backup location are displayed at the bottom of the Export Data for Prime Infrastructure page. The data being exported from LMS and the data imported back to PI are listed as follows.
    Data exported from LMS
    •Device Credentials Repository (DCR)
    •Software Image Management
    •Config Archive
    •Change Audit
    •Syslog
    Data Imported to PI
    Device Credentials Repository

  • Cisco Prime Infrastructure - not updating device details

    We run Cisco prime Infrastructure and I have found an interesting problem that I can't see an easy way round.
    If I have say a Cisco 2950 switch on my network, managed by Prime and I upgrade it to a 3560 - I then ask Prime to re-sync the device details.
    This works - you can see the updated configuration files etc but the device ID stays the same - Prime still thinks it is a 3560, which it was when the device was originally added.
    Is there a way, short of deleting the device and adding it again (losing the config archive) of getting prime to update it's details to reflect the hardware change?
    It came to light as it screwed up a network hardware audit I was doing - this is all showing up on Prime as the old 2050's which I have replaced with 3560's.
    There must be an easier way that just deleting the device and re-adding it?

    This is by no means a full solution, but deleting and re-adding only takes a few minutes if you use the "Export Device" and "Bulk Import" features from the Device Work Center. You can export the desired devices to a CSV file, delete them, then import from the CSV. 
    Of course, you might lose historical data when deleting the devices, but I'm guessing that's not as relevant since the devices themselves have been replaced by different hardware.

  • Prime Infrastructure 2.1.1 cannot add more than two interfaces in Dynamic Interface Controller Templates

    Cisco Prime Infrastructure is a damned nightmare of browser bugs (some features work in IE8, some in IE9, and some only in Firefox).  And I am not sure if what I am experiencing is a browser bug - or a real bug - or something that I was able to do before and can't any more?  I would love for someone to either explain why this is happening to me, or reproduce the bug!
    I'm running Prime 2.1.1.  I am doing this ...
    Configure > Controller Template Launchpad
    System > Dynamic Interface
    Select a command > Add interface (GO)
    Enter all the properties - roll to the bottom of the page, and click Apply to Controllers
    I have four controllers.  And normally I would add an interface for each controller.  But I can only create two out of the four.  It doesn't matter which two I choose.  When I click Add under Manage Interfaces for the third controller, I cannot click the Done button to apply it (see screenshot, attached).  I have found that if I change the VLAN to something else, it will let me save it.  But ... why?  I went back and reviewed all of my existing interface templates and I am not doing anything different.  Although, they were all created a long while ago using WCS 7.x.
    Any help, guidance, or confirmation of insanity would be appreciated.
    -Steve Ballantyne

    I doubt I will get any hits on this here but I always try.  I opened a TAC case.  I will come back and comment on whatever they find.

  • Prime Infrastructure 2.1 Client Statistic Report Issues

    Hello Community,
    I hope you can help with a couple of issues I am seeing on Prime Infrastructure 2.1, running an evaluation 60 day license.
    My PI 2.1 build is currently managing a WLC 5508 running 7.4.121.0, which has been added successfully. No configuration changes were applied to the WLCs, other than SNMP community. No AVC or medianet configuration is applied.
    When looking in the 'Operate>Client and Users' dashboard; I can see connected clients and if I select one of them, I can see further details like session, security and client statistics (showing traffic and 802.11 metrics). These are the table views that show current values, however, further down I see graphs but they do not contain any information for RSSI, SNR or traffic sent & received (packets or bytes).
    Question: Should I see this information under an evaluation license and if so, what could be stopping it?
    Also, when I run the reports 'Report>Report Launch Pad' and select 'Client>Client Traffic' or 'Client>Client Throughput' the resulting report contains 0 bps, when I select 'Report By' AP by Floor Area. I have created a single floor area and placed three access points into it.
    Out of interest if I do a report of the same type using 'Report By' All or AP by Controller, I do see traffic graphs for 3 out of 333 access points. Just not the access points that are in my floor area. Also the amount of traffic utilization is tiny (less than a kbps) for a WLC with 800 users.
    For a 'Client>Client Count' report using AP by Floor Area, I do see the client numbers connected to the WLC/APs in my configured floor area.
    Question: Should I see reports for client traffic and throughput under an evaluation license for floor areas and if so, what could be stopping it?
    I have checked the background task and the 'Client Statistics' task is enabled and run time is being updated.
    Kind regards,
    Ian

    Hi,
    here is an update:
    There are more than one Report you need to start to get data for Device, FAN, Power Supply, Module - look at these reports:
    Report > Report Launch Pad > Device > Inventory
    Report > Report Lauch Pad > Device > Wired Detailed Device Inventory
    Report > Report Lauch Pad > Device > Wired Module Detail > Wired Module Detail Report Details
    SFPs and GBICs cannot be reported til now - there are working on it.
    br,
    chris

  • Cisco prime Infrastructure alarms by e-mail

    hi all,
    my Cisco PI1.2 not send me a notification e-mail with specific alarm if occurred twice and the first time is not cleared or deleted.
    i.e.
    if a switch is down it send me a notification e-mail, and this switch comes up again but i did not remove the first alarm, the PI not send me a notification.
    please advice
    thanks in advance

    Alarm Status
    Description
    New
    When an event triggers a new alarm or an event is associated with an existing alarm.
    Acknowledged
    When you acknowledge an alarm, the status changes from New to Acknowledged.
    Cleared
    An alarm can be in these statuses:
    Auto-clear from the device—The fault is resolved on the device and an event is triggered for the same. For example, a device-reachable event clears the device-unreachable event. This in-turn, clears the device-unreachable alarm.
    Manual-clear from Prime Infrastructure users: You can manually clear an active alarm without resolving the fault in the network. A clearing event is triggered and this event clears the alarm.
    If the fault continues to exist in the network, a new event and alarm are created subsequently based on the event notification (traps/syslogs).
    This might be the reason, I believe.
    Please refer the following link for better understanding.
    http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/1-2/user/guide/prime_infra_ug/alarms.html
    Hope that helps.

  • Prime Infrastructure 2.0 Job Approval notifications?

    I have a question about notification for job approvers in Prime 2.0.  I'm trying to setup PI such that a restricted user can create a configuration change on a wireless controller and submit it for approval by the PI admin.
    The PI admin will likely not be logging in every day to check job approval status.   I can't see anywhere that notifies the admin via email that a job is waiting.  can this be done or am I missing something?
    -Tim

    Hi Tim,
    I don't think we have an email optiom to notify the ADMIN to approve the pending jobs ,however if you authorized any job then ONLY admin can approve to run the job.
    check the below link:
    http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/2.0/administrator/guide/config_server_settings.html#wp1081686
    Thanks-
    Afroz
    [Do rate the useful post]

  • Prime Infrastructure 2.0 Automatically add remove devices

    Dears,
    I'm basically looking for a dcrcli equivalent to use on prime infrastructure 2.0.
    Customer has a central repository of devices that must be monitored. When devices are added or removed there, they automagically appear or disappear in the other systems.
    Does something like this exist or is this on the roadmap?
    Cheers,
    Michel

    Hi Scott,
    Upto 7.3 config guide it was documented we have to reboot WLC when we configuring SNMP v3 which is wrong. (here is 7.3 config guide link for reference). May be older version (prior to 7.0) had that requirement, not too sure about it
    http://www.cisco.com/en/US/docs/wireless/controller/7.3/configuration/guide/b_wlc-cg_chapter_0100.html#d16741e4514a1635
    From 7.4 onwards config guide does not talk about it all. I deleted the default SNMPv3 user & create a new user in 7.4 & add it to prime without rebooting WLC.
    Once you configureed a SNMPv3 user on a WLC, I do no think you can edit/change the password. You have to delete the user & recreate it with modified username/password.Then re-add the WLC to prime
    The behaviour you mentioned is with any of later codes  of WLC ?
    Rasika

  • Cisco Prime Infrastructure 2.0 and Cisco ASA

    Hello,
    We've recently installed trial version of Cisco Prime Infrastructure 2.0 Express. We hoped that it already supports Cisco ASA 55xx series (especially 5505, we have pretty amount of them). But we had some problems with PI and asa durind the exploitation process.
    First, I've added ASA to PI, and Inventory Collection Status is Completed, but I can't see CPU and RAM utilization graphs. Inventory.logs are non-informative.
    Also, config backup is success, but when I try to watch the backuped configuration at Configuration Archive PI says "Failed to fetch raw configuration". And so on.
    ASA version is 5505, image is 9.1(2).
    So, I have a question: is it possible to manage ASAs with PI 2.0?
    UPD: I've just tried to upgrade asa to 9.1(4), and behavior of the equipment is quite the same. Seems we shall wait for 9.2 to be released.

    Have you downloaded and applied the latest Device Pack updates?
    PI enhanced ASA support after the initial 2.0 release and the Device Packs incorporate that change.
    The README file for Device Packs explains how to install them. (A bug currently does not allow the direct download in PI so you need to follow the method for installation from local storage after you manually download. Here is a link to the download location.

Maybe you are looking for