Change default username on Cisco 2960
Hi! It is possible to change de default username "admin" from Cisco 2960?
Ports Model SW Version SW Image
WS-C2960-24TC-L 12.2(35)SE5 C2960-LANBASEK9-M
Hello,
If you have console access, please try the following:
configure terminal
##### Create a new username/password pair ############
username priv 15 password
##### Configure HTTP access using local username ######
ip http authentication local
##### Configure telnet access using local username #####
line vty 0 4
login local
exit
If you want to delete a username, please use the following command:
no username
Hope this helps.
Regards,
NT
Similar Messages
-
How to change default admin password on Cisco Aironet 1040
How do I change the default username and password on the Cisco Aironet 1040. There is a default set and I want to change that to secure the device. I've checked the manual and can't seem to find the directions. Any ideas?
Hi Brian,
If this AP is already registered with a WLC then you can change it via WLC.
In WLC GUI, go to Wireless -> Select the AP -> Credential -> Override Global Credential-> Update username/pw/enable pw
In WLC CLI, you can configure it like this. If it is for all APs, then select all, otherwise AP name.
(WLC3) >config ap mgmtuser add username admin password Cisco123 secret Cisco123 ?
all Applies the configuration to every AP that does not have a specific user name.
Enter the name of the Cisco AP.
(WLC3) >config ap mgmtuser add username password secret
(WLC3) >save config
Are you sure you want to save? (y/n) y
If it is Autonomous AP you can configure using the "username xxxx password xxx" IOS command
HTH
Rasika
*** Pls rate all useful responses **** -
Cisco 2960-X & ISE accounting- username Radius attribute missing
Hi,
I'm facing an issue with cisco 2960 switch radius accounting with Cisco ISE1.2.1 .here is my senario:
- Username (vendor1) is configured in ISE local database, under group (VENDOR)
- Authentication protocol : wired MAB
- Authentication method : webauth using guest portal , the user is a vendor , so no dot1x configured on his NIC .
the problem is that , the switch is not sending the username as a part of radius attribute , in the authentication log , the username shown as the MAC address of the user machine , therefor , I can not configure my authorization condition using internaluser:Name Equal vendor1
while if I configure the condition using the identity group condition IdentityGroup:Name Equal VENDOR , it works .
The same configuration is working on 3750 switch with no issue .
Here is my Switch config:
aaa authentication login default local
aaa authentication dot1x default group radius
aaa authorization network default group radius
aaa authorization auth-proxy default group radius
aaa accounting auth-proxy default start-stop group radius
aaa accounting dot1x default start-stop group radius
aaa accounting update periodic 5
username admin password
username radius-test password
aaa server radius dynamic-author
client 172.16.2.20 server-key 7 04490A0206345F450C00
client 172.16.2.21 server-key 7 03165A0F0F1A32474B10
radius server ISE-RADIUS-1
address ipv4 172.16.2.20 auth-port 1812 acct-port 1813
automate-tester username radius-test idle-time 15
key 7 111B18011E0718070133
radius server ISE-RADIUS-2
address ipv4 172.16.2.21 auth-port 1812 acct-port 1813
automate-tester username radius-test idle-time 15
key 7 0214055F02131C2A4957
radius-server attribute 6 on-for-login-auth
radius-server attribute 8 include-in-access-req
radius-server attribute 25 access-request include
radius-server attribute 31 mac format ietf upper-case
radius-server attribute 31 send nas-port-detail
radius-server dead-criteria time 5 tries 3
radius-server vsa send accounting
radius-server vsa send authentication
any help !!!Thanks for your reply , I know what's MAB , if you read my explanation again , i mentioned that the user is authenticated in the guest portal which mean that I have web authentication , and it is working fine .. The only issue is that I can not use the vendor1 username as part of authorization condition and this is because the switch is not sending the radius attribute type 1 to the ISE , thus , on the ise authentication log the MAC address of the client machine is shown as a username not the actual username ( vendor1)
as I mentioned also , I have exactly the same setup with ise 1.2 and 3750 switch and I do not have this issue .I experience this with 2960x only . -
I recently changed my username n password. Now that I'm trying to update my apps, it still default at my old username. How can I change it to new username?
Sorry, you can't. Apps are forever tied to the Apple ID used to originally obtain them. They cannot be updated using any other Apple ID, nor can they be transferred to another Apple ID. You will have to update them using the ID used to originally obtain them.
-
IEEE 802.1x with EAP-TLS issue in cisco 2960
In My Cisco 2960 switch is not working with EAP-TLS mechanism of 802.1x but its works well with other protocols like EAP-PEAP or MAC Address authentication.
Below is the configuration
aaa authentication login default group tacacs+ local
aaa authentication enable default group tacacs+ enable
aaa authentication dot1x default group radius
aaa authorization commands 15 default group tacacs+ local
aaa authorization network default group radius
aaa authorization configuration default group radius
aaa accounting update periodic 30
aaa accounting dot1x default start-stop group radius
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 0 default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa accounting network default start-stop group tacacs+
aaa accounting connection default start-stop group tacacs+
aaa accounting system default start-stop group tacacs+
interface FastEthernet0/1
switchport access vlan 11
switchport mode access
speed 100
duplex full
authentication order dot1x mab webauth
authentication port-control auto
mab
dot1x pae authenticator
dot1x timeout tx-period 3
dot1x timeout supp-timeout 3
spanning-tree portfast
spanning-tree bpduguard enable
Can anyone suggest me ?Thanks for the reply jatin.
I have a client on the interface fa0/1 with a valid client certificate. And have a debug logs as below
*Mar 8 00:03:06.266: dot1x-ev(Fa0/1): Interface state changed to UP
*Mar 8 00:03:06.266: AAA/BIND(000001C7): Bind i/f
*Mar 8 00:03:06.266: dot1x_auth Fa0/1: initial state auth_initialize has enter
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_initialize_enter called
*Mar 8 00:03:06.266: dot1x_auth Fa0/1: during state auth_initialize, got event 0(cfg_auto)
*Mar 8 00:03:06.266: @@@ dot1x_auth Fa0/1: auth_initialize -> auth_disconnected
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_disconnected_enter called
*Mar 8 00:03:06.266: dot1x_auth Fa0/1: idle during state auth_disconnected
*Mar 8 00:03:06.266: @@@ dot1x_auth Fa0/1: auth_disconnected -> auth_restart
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_enter called
*Mar 8 00:03:06.266: dot1x-ev(Fa0/1): Sending create new context event to EAP for 0xB0000DBA (0000.0000.0000)
*Mar 8 00:03:06.266: dot1x_auth_bend Fa0/1: initial state auth_bend_initialize has enter
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_initialize_enter called
*Mar 8 00:03:06.266: dot1x_auth_bend Fa0/1: initial state auth_bend_initialize has idle
*Mar 8 00:03:06.266: dot1x_auth_bend Fa0/1: during state auth_bend_initialize, got event 16383(idle)
*Mar 8 00:03:06.266: @@@ dot1x_auth_bend Fa0/1: auth_bend_initialize -> auth_bend_idle
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_enter called
*Mar 8 00:03:06.266: dot1x-ev(Fa0/1): Created a client entry (0xB0000DBA)
*Mar 8 00:03:06.266: dot1x-ev(Fa0/1): Dot1x authentication started for 0xB0000DBA (0000.0000.0000)
*Mar 8 00:03:06.266: dot1x-ev:DOT1X Supplicant not enabled on FastEthernet0/1
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): Posting !EAP_RESTART on Client 0xB0000DBA
*Mar 8 00:03:06.266: dot1x_auth Fa0/1: during state auth_restart, got event 6(no_eapRestart)
*Mar 8 00:03:06.266: @@@ dot1x_auth Fa0/1: auth_restart -> auth_connecting
*Mar 8 00:03:06.266: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_enter called
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_connecting_action called
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): Posting RX_REQ on Client 0xB0000DBA
*Mar 8 00:03:06.274: dot1x_auth Fa0/1: during state auth_connecting, got event 10(eapReq_no_reAuthMax)
*Mar 8 00:03:06.274: @@@ dot1x_auth Fa0/1: auth_connecting -> auth_authenticating
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authenticating_enter called
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_authenticating_action called
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): Posting AUTH_START for 0xB0000DBA
*Mar 8 00:03:06.274: dot1x_auth_bend Fa0/1: during state auth_bend_idle, got event 4(eapReq_authStart)
*Mar 8 00:03:06.274: @@@ dot1x_auth_bend Fa0/1: auth_bend_idle -> auth_bend_request
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
*Mar 8 00:03:06.274: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:06.274: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.274: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:06.274: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:06.274: EAPOL pak dump Tx
*Mar 8 00:03:06.274: EAPOL Version: 0x3 type: 0x0 length: 0x0005
*Mar 8 00:03:06.274: EAP code: 0x1 id: 0x1 length: 0x0005 type: 0x1
*Mar 8 00:03:06.274: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (0000.0000.0000)
*Mar 8 00:03:06.274: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_request_action called
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.794: dot1x-packet(Fa0/1): queuing an EAPOL pkt on Auth Q
*Mar 8 00:03:06.794: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
*Mar 8 00:03:06.794: EAPOL pak dump rx
*Mar 8 00:03:06.794: EAPOL Version: 0x1 type: 0x1 length: 0x0000
*Mar 8 00:03:06.794: dot1x-ev:
dot1x_auth_queue_event: Int Fa0/1 CODE= 0,TYPE= 0,LEN= 0
*Mar 8 00:03:06.794: dot1x-packet(Fa0/1): Received an EAPOL frame
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Received pkt saddr =d43d.7e65.4fc1 , daddr = 0180.c200.0003,
pae-ether-type = 888e.0101.0000
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Couldn't find the supplicant in the list
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): New client detected, notifying AuthMgr
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Sending event (0) to Auth Mgr for d43d.7e65.4fc1
*Mar 8 00:03:06.794: dot1x-packet(Fa0/1): Received an EAPOL-Start packet
*Mar 8 00:03:06.794: EAPOL pak dump rx
*Mar 8 00:03:06.794: EAPOL Version: 0x1 type: 0x1 length: 0x0000
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): Posting EAPOL_START on Client 0xB0000DBA
*Mar 8 00:03:06.794: dot1x_auth Fa0/1: during state auth_authenticating, got event 4(eapolStart)
*Mar 8 00:03:06.794: @@@ dot1x_auth Fa0/1: auth_authenticating -> auth_aborting
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authenticating_exit called
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_aborting_enter called
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): 802.1x method gets the go ahead from Auth Mgr for 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.794: %AUTHMGR-5-START: Starting 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EE240F5BAB
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): Posting AUTH_ABORT for 0xB0000DBA
*Mar 8 00:03:06.794: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 1(authAbort)
*Mar 8 00:03:06.794: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_initialize
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_initialize_enter called
*Mar 8 00:03:06.794: dot1x_auth_bend Fa0/1: idle during state auth_bend_initialize
*Mar 8 00:03:06.794: @@@ dot1x_auth_bend Fa0/1: auth_bend_initialize -> auth_bend_idle
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_enter called
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): Posting !AUTH_ABORT on Client 0xB0000DBA
*Mar 8 00:03:06.794: dot1x_auth Fa0/1: during state auth_aborting, got event 20(no_eapolLogoff_no_authAbort)
*Mar 8 00:03:06.794: @@@ dot1x_auth Fa0/1: auth_aborting -> auth_restart
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_aborting_exit called
*Mar 8 00:03:06.794: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_enter called
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Resetting the client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.794: dot1x-ev(Fa0/1): Sending create new context event to EAP for 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.802: dot1x-sm(Fa0/1): 0xB0000DBA:auth_aborting_restart_action called
*Mar 8 00:03:06.802: dot1x-sm(Fa0/1): Posting !EAP_RESTART on Client 0xB0000DBA
*Mar 8 00:03:06.802: dot1x_auth Fa0/1: during state auth_restart, got event 6(no_eapRestart)
*Mar 8 00:03:06.802: @@@ dot1x_auth Fa0/1: auth_restart -> auth_connecting
*Mar 8 00:03:06.802: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_enter called
*Mar 8 00:03:06.802: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_connecting_action called
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): Posting RX_REQ on Client 0xB0000DBA
*Mar 8 00:03:06.811: dot1x_auth Fa0/1: during state auth_connecting, got event 10(eapReq_no_reAuthMax)
*Mar 8 00:03:06.811: @@@ dot1x_auth Fa0/1: auth_connecting -> auth_authenticating
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authenticating_enter called
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_authenticating_action called
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): Posting AUTH_START for 0xB0000DBA
*Mar 8 00:03:06.811: dot1x_auth_bend Fa0/1: during state auth_bend_idle, got event 4(eapReq_authStart)
*Mar 8 00:03:06.811: @@@ dot1x_auth_bend Fa0/1: auth_bend_idle -> auth_bend_request
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.811: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:06.811: EAPOL pak dump Tx
*Mar 8 00:03:06.811: EAPOL Version: 0x3 type: 0x0 length: 0x0005
*Mar 8 00:03:06.811: EAP code: 0x1 id: 0x1 length: 0x0005 type: 0x1
*Mar 8 00:03:06.811: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_request_action called
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.811: dot1x-packet(Fa0/1): Queuing an EAPOL pkt on Authenticator Q
*Mar 8 00:03:06.811: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
*Mar 8 00:03:06.811: EAPOL pak dump rx
*Mar 8 00:03:06.811: EAPOL Version: 0x1 type: 0x0 length: 0x0022
*Mar 8 00:03:06.811: dot1x-ev:
dot1x_auth_queue_event: Int Fa0/1 CODE= 2,TYPE= 1,LEN= 34
*Mar 8 00:03:06.811: dot1x-packet(Fa0/1): Received an EAPOL frame
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): Received pkt saddr =d43d.7e65.4fc1 , daddr = 0180.c200.0003,
pae-ether-type = 888e.0100.0022
*Mar 8 00:03:06.811: dot1x-packet(Fa0/1): Received an EAP packet
*Mar 8 00:03:06.811: EAPOL pak dump rx
*Mar 8 00:03:06.811: EAPOL Version: 0x1 type: 0x0 length: 0x0022
*Mar 8 00:03:06.811: dot1x-packet(Fa0/1): Received an EAP packet from d43d.7e65.4fc1
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): Posting EAPOL_EAP for 0xB0000DBA
*Mar 8 00:03:06.811: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 6(eapolEap)
*Mar 8 00:03:06.811: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_response
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_enter called
*Mar 8 00:03:06.811: dot1x-ev(Fa0/1): dot1x_sendRespToServer: Response sent to the server from 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.811: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_response_action called
*Mar 8 00:03:06.811: AAA/AUTHEN/8021X (000001C7): Pick method list 'default'
*Mar 8 00:03:06.819: RADIUS/ENCODE(000001C7):Orig. component type = DOT1X
*Mar 8 00:03:06.819: RADIUS(000001C7): Config NAS IP: 0.0.0.0
*Mar 8 00:03:06.819: RADIUS/ENCODE(000001C7): acct_session_id: 724
*Mar 8 00:03:06.819: RADIUS(000001C7): sending
*Mar 8 00:03:06.819: RADIUS/ENCODE: Best Local IP-Address 10.26.237.11 for Radius-Server 10.26.13.59
*Mar 8 00:03:06.819: RADIUS(000001C7): Send Access-Request to 10.26.13.59:1812 id 1645/83, len 251
*Mar 8 00:03:06.819: RADIUS: authenticator A1 79 FA E5 F4 B7 7F 4F - 2B 73 3A 0D 1F D8 89 20
*Mar 8 00:03:06.819: RADIUS: User-Name [1] 31 "host/D0902MALL005.IN.intranet"
*Mar 8 00:03:06.819: RADIUS: Service-Type [6] 6 Framed [2]
*Mar 8 00:03:06.819: RADIUS: Framed-MTU [12] 6 1500
*Mar 8 00:03:06.819: RADIUS: Called-Station-Id [30] 19 "D4-A0-2A-EE-14-81"
*Mar 8 00:03:06.819: RADIUS: Calling-Station-Id [31] 19 "D4-3D-7E-65-4F-C1"
*Mar 8 00:03:06.819: RADIUS: EAP-Message [79] 36
*Mar 8 00:03:06.819: RADIUS: 02 01 00 22 01 68 6F 73 74 2F 44 30 39 30 32 4D 41 4C 4C 30 ["host/D0902MALL0]
*Mar 8 00:03:06.819: RADIUS: 30 35 2E 49 4E 2E 69 6E 74 72 61 6E 65 74 [ 05.IN.intranet]
*Mar 8 00:03:06.819: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:06.819: RADIUS: D6 6F 7B CD 36 46 5E F6 90 6F 85 A8 BD BD AE D8 [ o{6F^o]
*Mar 8 00:03:06.819: RADIUS: EAP-Key-Name [102] 2 *
*Mar 8 00:03:06.819: RADIUS: Vendor, Cisco [26] 49
*Mar 8 00:03:06.819: RADIUS: Cisco AVpair [1] 43 "audit-session-id=0A1AED0B000000EE240F5BAB"
*Mar 8 00:03:06.819: RADIUS: NAS-Port-Type [61] 6 Ethernet [15]
*Mar 8 00:03:06.819: RADIUS: NAS-Port [5] 6 50001
*Mar 8 00:03:06.819: RADIUS: NAS-Port-Id [87] 17 "FastEthernet0/1"
*Mar 8 00:03:06.819: RADIUS: NAS-IP-Address [4] 6 10.26.237.11
*Mar 8 00:03:06.819: RADIUS: Acct-Session-Id [44] 10 "000002D4"
*Mar 8 00:03:06.819: RADIUS(000001C7): Started 3 sec timeout
*Mar 8 00:03:06.861: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
*Mar 8 00:03:06.903: RADIUS: Received from id 1645/83 10.26.13.59:1812, Access-Challenge, len 76
*Mar 8 00:03:06.903: RADIUS: authenticator 7B 1C DC CA A8 92 E9 34 - 17 86 25 2F 9D 7E 63 96
*Mar 8 00:03:06.903: RADIUS: EAP-Message [79] 8
*Mar 8 00:03:06.903: RADIUS: 01 02 00 06 0D 20 [ ]
*Mar 8 00:03:06.903: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:06.903: RADIUS: DD F3 7B 33 37 6D 40 BD F3 D2 78 DF F1 14 4D E4 [ {37m@xM]
*Mar 8 00:03:06.903: RADIUS: State [24] 30
*Mar 8 00:03:06.903: RADIUS: 00 7D 00 9B 00 C1 00 40 ED B8 45 00 FC DD 50 2E DC 0E E6 03 FC 7B AD 4C B7 E7 B1 70 [ }@EP.{Lp]
*Mar 8 00:03:06.911: RADIUS(000001C7): Received from id 1645/83
*Mar 8 00:03:06.911: RADIUS/DECODE: EAP-Message fragments, 6, total 6 bytes
*Mar 8 00:03:06.911: dot1x-sm(Fa0/1): Posting EAP_REQ for 0xB0000DBA
*Mar 8 00:03:06.911: dot1x_auth_bend Fa0/1: during state auth_bend_response, got event 7(eapReq)
*Mar 8 00:03:06.911: @@@ dot1x_auth_bend Fa0/1: auth_bend_response -> auth_bend_request
*Mar 8 00:03:06.911: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_exit called
*Mar 8 00:03:06.911: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
*Mar 8 00:03:06.911: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:06.911: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.911: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:06.911: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:06.911: EAPOL pak dump Tx
*Mar 8 00:03:06.911: EAPOL Version: 0x3 type: 0x0 length: 0x0006
*Mar 8 00:03:06.911: EAP code: 0x1 id: 0x2 length: 0x0006 type: 0xD
*Mar 8 00:03:06.911: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.911: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_request_action called
*Mar 8 00:03:06.920: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:06.920: dot1x-packet(Fa0/1): Queuing an EAPOL pkt on Authenticator Q
*Mar 8 00:03:06.920: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
*Mar 8 00:03:06.920: EAPOL pak dump rx
*Mar 8 00:03:06.920: EAPOL Version: 0x1 type: 0x0 length: 0x0069
*Mar 8 00:03:06.920: dot1x-ev:
dot1x_auth_queue_event: Int Fa0/1 CODE= 2,TYPE= 13,LEN= 105
*Mar 8 00:03:06.920: dot1x-packet(Fa0/1): Received an EAPOL frame
*Mar 8 00:03:06.920: dot1x-ev(Fa0/1): Received pkt saddr =d43d.7e65.4fc1 , daddr = 0180.c200.0003,
pae-ether-type = 888e.0100.0069
*Mar 8 00:03:06.920: dot1x-packet(Fa0/1): Received an EAP packet
*Mar 8 00:03:06.920: EAPOL pak dump rx
*Mar 8 00:03:06.920: EAPOL Version: 0x1 type: 0x0 length: 0x0069
*Mar 8 00:03:06.920: dot1x-packet(Fa0/1): Received an EAP packet from d43d.7e65.4fc1
*Mar 8 00:03:06.920: dot1x-sm(Fa0/1): Posting EAPOL_EAP for 0xB0000DBA
*Mar 8 00:03:06.920: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 6(eapolEap)
*Mar 8 00:03:06.920: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_response
*Mar 8 00:03:06.920: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_enter called
*Mar 8 00:03:06.920: dot1x-ev(Fa0/1): dot1x_sendRespToServer: Response sent to the server from 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:06.920: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_response_action called
*Mar 8 00:03:06.920: AAA/AUTHEN/8021X (000001C7): Pick method list 'default'
*Mar 8 00:03:06.920: RADIUS/ENCODE(000001C7):Orig. component type = DOT1X
*Mar 8 00:03:06.920: RADIUS(000001C7): Config NAS IP: 0.0.0.0
*Mar 8 00:03:06.920: RADIUS/ENCODE(000001C7): acct_session_id: 724
*Mar 8 00:03:06.920: RADIUS(000001C7): sending
*Mar 8 00:03:06.920: RADIUS/ENCODE: Best Local IP-Address 10.26.237.11 for Radius-Server 10.26.13.59
*Mar 8 00:03:06.920: RADIUS(000001C7): Send Access-Request to 10.26.13.59:1812 id 1645/84, len 352
*Mar 8 00:03:06.920: RADIUS: authenticator 41 72 8D 6A B4 72 19 84 - 1B C8 33 F7 95 DD 07 BC
*Mar 8 00:03:06.928: RADIUS: User-Name [1] 31 "host/D0902MALL005.IN.intranet"
*Mar 8 00:03:06.928: RADIUS: Service-Type [6] 6 Framed [2]
*Mar 8 00:03:06.928: RADIUS: Framed-MTU [12] 6 1500
*Mar 8 00:03:06.928: RADIUS: Called-Station-Id [30] 19 "D4-A0-2A-EE-14-81"
*Mar 8 00:03:06.928: RADIUS: Calling-Station-Id [31] 19 "D4-3D-7E-65-4F-C1"
*Mar 8 00:03:06.928: RADIUS: EAP-Message [79] 107
*Mar 8 00:03:06.928: RADIUS: 02 02 00 69 0D 80 00 00 00 5F 16 03 01 00 5A 01 00 00 56 03 01 52 C5 45 4F 07 CA B3 29 50 A7 CE 40 76 B6 BD F0 50 D4 CE 9A 8A 02 C4 3D 40 35 B5 F0 E1 E2 75 [i_ZVREO)P@vP=@5u]
*Mar 8 00:03:06.928: RADIUS: 50 00 00 18 00 2F 00 35 00 05 00 0A C0 13 C0 14 C0 09 C0 0A 00 32 00 38 00 13 00 04 01 00 00 15 FF 01 00 01 00 00 0A 00 06 00 04 00 17 00 18 00 0B 00 02 01 00 [ P/528]
*Mar 8 00:03:06.928: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:06.928: RADIUS: A3 28 CE 27 20 C0 D6 2C 11 01 D6 61 1F C3 6F 03 [ (' ,ao]
*Mar 8 00:03:06.928: RADIUS: EAP-Key-Name [102] 2 *
*Mar 8 00:03:06.928: RADIUS: Vendor, Cisco [26] 49
*Mar 8 00:03:06.928: RADIUS: Cisco AVpair [1] 43 "audit-session-id=0A1AED0B000000EE240F5BAB"
*Mar 8 00:03:06.928: RADIUS: NAS-Port-Type [61] 6 Ethernet [15]
*Mar 8 00:03:06.928: RADIUS: NAS-Port [5] 6 50001
*Mar 8 00:03:06.928: RADIUS: NAS-Port-Id [87] 17 "FastEthernet0/1"
*Mar 8 00:03:06.928: RADIUS: State [24] 30
*Mar 8 00:03:06.928: RADIUS: 00 7D 00 9B 00 C1 00 40 ED B8 45 00 FC DD 50 2E DC 0E E6 03 FC 7B AD 4C B7 E7 B1 70 [ }@EP.{Lp]
*Mar 8 00:03:06.928: RADIUS: NAS-IP-Address [4] 6 10.26.237.11
*Mar 8 00:03:06.928: RADIUS: Acct-Session-Id [44] 10 "000002D4"
*Mar 8 00:03:06.928: RADIUS(000001C7): Started 3 sec timeout
*Mar 8 00:03:07.004: RADIUS: Received from id 1645/84 10.26.13.59:1812, Access-Challenge, len 1188
*Mar 8 00:03:07.004: RADIUS: authenticator 7B 52 29 05 7E C3 EF 8E - 13 38 30 03 4B 65 64 0F
*Mar 8 00:03:07.004: RADIUS: EAP-Message [79] 255
*Mar 8 00:03:07.004: RADIUS: 01 03 04 56 0D C0 00 00 05 78 16 03 01 00 51 02 00 00 4D 03 01 52 C5 45 4F 0F 04 37 77 A0 C2 68 66 4E 45 92 AB 3D 7F 94 70 AF 36 [VxQMREO7whfNE=p6]
*Mar 8 00:03:07.004: RADIUS: 1D C5 17 23 5C F1 FA CA 60 B0 20 A5 48 16 D5 3F F9 B0 FF 38 1D D5 13 B3 88 13 06 EF DC 87 5C AE 17 E7 7E 80 84 21 58 64 F7 A6 36 00 35 00 00 05 FF 01 00 01 00 16 03 01 02 1C 0B 00 02 18 00 02 15 00 02 12 30 82 02 0E 30 [#\` H?8\~!Xd6500]
*Mar 8 00:03:07.004: RADIUS: 82 01 77 A0 03 02 01 02 02 09 00 88 7A CB 35 3F 1E 3E 62 30 0D 06 09 2A 86 48 86 F7 0D 01 01 05 05 00 30 2F 31 15 30 13 06 03 55 04 03 13 0C 53 50 [wz5?>b0*H0/10USP]
*Mar 8 00:03:07.004: RADIUS: 49 4E 41 56 44 30 30 30 30 34 31 16 30 14 06 03 55 04 0A 13 0D 50 6F 6C [INAVD0000410UPol]
*Mar 8 00:03:07.004: RADIUS: 69 63 79 4D 61 6E 61 67 65 72 30 1E 17 0D 31 33 30 38 32 [icyManager013082]
*Mar 8 00:03:07.004: RADIUS: 37 30 37 32 34 33 30 5A 17 0D 31 34 30 38 32 37 30 37 [7072430Z14082707]
*Mar 8 00:03:07.004: RADIUS: 32 34 33 30 5A 30 2F 31 15 30 13 06 03 55 04 03 13 0C 53 50 49 4E 41 56 [2430Z0/10USPINAV]
*Mar 8 00:03:07.004: RADIUS: 44 30 30 [ D00]
*Mar 8 00:03:07.004: RADIUS: EAP-Message [79] 255
*Mar 8 00:03:07.004: RADIUS: 30 30 34 31 16 30 14 06 03 55 04 0A 13 0D 50 6F 6C 69 63 79 4D 61 6E 61 [00410UPolicyMana]
*Mar 8 00:03:07.004: RADIUS: 67 65 72 30 81 9F 30 0D 06 09 2A 86 48 86 F7 0D 01 01 01 05 00 03 81 8D 00 30 81 89 02 81 81 00 C9 B9 03 65 83 EB 39 86 14 BC 95 7B DB 07 7E C5 8A D7 DA C7 8A CA 5A 88 6E 0B 93 06 35 57 [ger00*H0e9{~Zn5W]
*Mar 8 00:03:07.012: RADIUS: 6E DE 93 CD C9 FE 8E 9F E1 5F A9 04 5C BD A9 AD 5A 04 6E 35 47 76 A1 58 E5 C4 32 D7 49 9E 17 75 20 C6 6F 45 40 [n_\Zn5GvX2Iu oE@]
*Mar 8 00:03:07.012: RADIUS: AC EF 40 6D 15 38 F9 C2 28 7E C9 68 37 52 3B BF F4 C1 5E B8 BA 46 68 43 79 B1 65 66 [@m8(~h7R;^FhCyef]
*Mar 8 00:03:07.012: RADIUS: 9E 58 ED EC 8C 95 A2 D8 BF AA 77 AC 85 90 E3 AB C6 27 3A A2 22 AC 1C 48 B3 BF BE F7 85 CF 5C BB 2D 02 03 01 00 01 A3 32 30 30 30 0F 06 03 55 1D 11 04 08 30 06 87 04 0A 1A 0D 3B 30 [Xw':"H\-2000U0;0]
*Mar 8 00:03:07.012: RADIUS: 1D 06 03 55 1D 25 04 16 30 14 06 08 2B 06 01 05 05 07 03 01 06 08 2B 06 01 05 05 07 03 03 30 0D 06 09 2A 86 48 86 F7 0D 01 01 [ U?0++0*H]
*Mar 8 00:03:07.012: RADIUS: EAP-Message [79] 255
*Mar 8 00:03:07.012: RADIUS: 05 05 00 03 81 81 00 C4 46 3E 38 3D 53 0F 28 34 C1 A6 ED DC 70 76 9B 70 6B A8 95 7C 44 8E 7D 6E D6 8B 6D [F>8=S(4pvpk|D}nm]
*Mar 8 00:03:07.012: RADIUS: 90 49 83 06 E4 BF 68 2F 9D 77 78 A3 76 76 19 84 AD 26 3F F3 ED AA 88 52 35 0E 35 DD 00 E5 96 88 44 30 79 A0 71 [Ih/wxvv&?R55D0yq]
*Mar 8 00:03:07.012: RADIUS: 8D 25 3E 77 A0 E0 43 92 33 55 40 E1 C8 EE 88 11 25 E2 70 28 11 6C 5A 4E 3D F1 93 57 0A 6F [?>wC3U@?p(lZN=Wo]
*Mar 8 00:03:07.012: RADIUS: 36 51 72 04 08 C0 C0 DF F0 94 A9 F7 A1 05 C8 37 D6 F8 D4 9C 20 1A 7B CD 2C 17 83 7B 8E 20 F7 2D B6 16 03 01 02 FC 0D 00 02 F4 03 01 02 40 02 EE 00 63 30 61 31 0B 30 [6Qr7 {,{ -@c0a10]
*Mar 8 00:03:07.012: RADIUS: 09 06 03 55 04 06 13 02 55 53 31 15 30 13 06 03 55 04 0A 13 0C 44 69 67 69 43 65 72 74 20 49 [UUS10UDigiCert I]
*Mar 8 00:03:07.012: RADIUS: 6E 63 31 19 30 17 06 03 55 04 0B 13 10 77 77 77 2E 64 69 67 69 63 65 72 [nc10Uwww.digicer]
*Mar 8 00:03:07.012: RADIUS: 74 2E 63 6F 6D 31 20 30 1E 06 03 55 04 03 13 17 44 69 67 69 43 65 72 [t.com1 0UDigiCer]
*Mar 8 00:03:07.012: RADIUS: 74 20 47 6C 6F 62 61 6C 20 52 6F 6F 74 20 43 41 [t Global Root CA]
*Mar 8 00:03:07.012: RADIUS: 00 48 [ H]
*Mar 8 00:03:07.012: RADIUS: EAP-Message [79] 255
*Mar 8 00:03:07.012: RADIUS: 30 46 31 18 30 16 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 08 69 6E 74 72 61 6E 65 74 31 [0F10&,dintranet1]
*Mar 8 00:03:07.020: RADIUS: 12 30 10 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 02 49 4E 31 16 30 14 06 03 55 04 03 13 0D 49 6E 64 69 61 20 52 [0&,dIN10UIndia R]
*Mar 8 00:03:07.020: RADIUS: 6F 6F 74 20 43 41 00 4A 30 48 31 18 30 16 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 08 69 6E [oot CAJ0H10&,din]
*Mar 8 00:03:07.020: RADIUS: 74 72 61 6E 65 74 31 12 30 10 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 02 49 4E 31 18 30 16 06 03 55 [tranet10&,dIN10U]
*Mar 8 00:03:07.020: RADIUS: 04 03 13 0F 45 6E 74 65 72 70 72 69 73 65 20 43 41 2D 31 00 4D [Enterprise CA-1M]
*Mar 8 00:03:07.020: RADIUS: 30 4B 31 18 30 16 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 08 69 6E 74 72 61 6E 65 74 31 [0K10&,dintranet1]
*Mar 8 00:03:07.020: RADIUS: 12 30 10 06 0A 09 92 26 89 93 F2 2C 64 01 19 16 02 49 4E 31 1B 30 19 06 03 55 04 03 13 12 49 4E 2D 53 50 49 4E [0&,dIN10UIN-SPIN]
*Mar 8 00:03:07.020: RADIUS: 43 52 54 30 30 30 30 33 2D 43 41 00 D5 30 81 D2 31 0B 30 09 06 03 55 04 06 13 02 55 [CRT00003-CA010UU]
*Mar 8 00:03:07.020: RADIUS: 53 31 13 30 11 06 03 55 04 [ S10U]
*Mar 8 00:03:07.020: RADIUS: EAP-Message [79] 100
*Mar 8 00:03:07.020: RADIUS: 08 0C 0A 43 61 6C 69 66 6F 72 6E 69 61 31 12 30 10 06 03 55 04 07 0C 09 53 75 6E [California10USun]
*Mar 8 00:03:07.020: RADIUS: 6E 79 76 61 6C 65 31 17 30 15 06 03 55 04 0A 0C 0E 41 72 75 62 61 20 4E [nyvale10UAruba N]
*Mar 8 00:03:07.020: RADIUS: 65 74 77 6F 72 6B 73 31 40 30 3E 06 03 55 04 03 0C 37 43 6C 65 [etworks1@0>U7Cle]
*Mar 8 00:03:07.020: RADIUS: 61 72 50 61 73 73 20 4F 6E 62 6F 61 72 64 20 4C [arPass Onboard L]
*Mar 8 00:03:07.020: RADIUS: 6F 63 61 6C 20 43 65 72 74 69 [ ocal Certi]
*Mar 8 00:03:07.020: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:07.020: RADIUS: 12 75 40 41 6F 40 6B 6F A5 FE AB 85 F3 B3 CF A4 [ u@Ao@ko]
*Mar 8 00:03:07.020: RADIUS: State [24] 30
*Mar 8 00:03:07.020: RADIUS: 00 6F 00 51 00 4B 00 6E EE B8 45 00 4B AA 6B A9 B6 D6 C8 CC 48 1A 91 99 7F 77 D3 C1 [ oQKnEKkHw]
*Mar 8 00:03:07.029: RADIUS(000001C7): Received from id 1645/84
*Mar 8 00:03:07.029: RADIUS/DECODE: EAP-Message fragments, 253+253+253+253+98, total 1110 bytes
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): Posting EAP_REQ for 0xB0000DBA
*Mar 8 00:03:07.037: dot1x_auth_bend Fa0/1: during state auth_bend_response, got event 7(eapReq)
*Mar 8 00:03:07.037: @@@ dot1x_auth_bend Fa0/1: auth_bend_response -> auth_bend_request
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_exit called
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:07.037: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:07.037: EAPOL pak dump Tx
*Mar 8 00:03:07.037: EAPOL Version: 0x3 type: 0x0 length: 0x0456
*Mar 8 00:03:07.037: EAP code: 0x1 id: 0x3 length: 0x0456 type: 0xD
*Mar 8 00:03:07.037: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_request_action called
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:07.037: dot1x-packet(Fa0/1): Queuing an EAPOL pkt on Authenticator Q
*Mar 8 00:03:07.037: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
*Mar 8 00:03:07.037: EAPOL pak dump rx
*Mar 8 00:03:07.037: EAPOL Version: 0x1 type: 0x0 length: 0x0006
*Mar 8 00:03:07.037: dot1x-ev:
dot1x_auth_queue_event: Int Fa0/1 CODE= 2,TYPE= 13,LEN= 6
*Mar 8 00:03:07.037: dot1x-packet(Fa0/1): Received an EAPOL frame
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): Received pkt saddr =d43d.7e65.4fc1 , daddr = 0180.c200.0003,
pae-ether-type = 888e.0100.0006
*Mar 8 00:03:07.037: dot1x-packet(Fa0/1): Received an EAP packet
*Mar 8 00:03:07.037: EAPOL pak dump rx
*Mar 8 00:03:07.037: EAPOL Version: 0x1 type: 0x0 length: 0x0006
*Mar 8 00:03:07.037: dot1x-packet(Fa0/1): Received an EAP packet from d43d.7e65.4fc1
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): Posting EAPOL_EAP for 0xB0000DBA
*Mar 8 00:03:07.037: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 6(eapolEap)
*Mar 8 00:03:07.037: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_response
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_enter called
*Mar 8 00:03:07.037: dot1x-ev(Fa0/1): dot1x_sendRespToServer: Response sent to the server from 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:07.037: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_response_action called
*Mar 8 00:03:07.037: AAA/AUTHEN/8021X (000001C7): Pick method list 'default'
*Mar 8 00:03:07.046: RADIUS/ENCODE(000001C7):Orig. component type = DOT1X
*Mar 8 00:03:07.046: RADIUS(000001C7): Config NAS IP: 0.0.0.0
*Mar 8 00:03:07.046: RADIUS/ENCODE(000001C7): acct_session_id: 724
*Mar 8 00:03:07.046: RADIUS(000001C7): sending
*Mar 8 00:03:07.046: RADIUS/ENCODE: Best Local IP-Address 10.26.237.11 for Radius-Server 10.26.13.59
*Mar 8 00:03:07.046: RADIUS(000001C7): Send Access-Request to 10.26.13.59:1812 id 1645/85, len 253
*Mar 8 00:03:07.046: RADIUS: authenticator 1C D7 6D 40 A3 D6 BA B1 - A7 E6 70 DA 32 83 2E 19
*Mar 8 00:03:07.046: RADIUS: User-Name [1] 31 "host/D0902MALL005.IN.intranet"
*Mar 8 00:03:07.046: RADIUS: Service-Type [6] 6 Framed [2]
*Mar 8 00:03:07.046: RADIUS: Framed-MTU [12] 6 1500
*Mar 8 00:03:07.046: RADIUS: Called-Station-Id [30] 19 "D4-A0-2A-EE-14-81"
*Mar 8 00:03:07.046: RADIUS: Calling-Station-Id [31] 19 "D4-3D-7E-65-4F-C1"
*Mar 8 00:03:07.046: RADIUS: EAP-Message [79] 8
*Mar 8 00:03:07.046: RADIUS: 02 03 00 06 0D 00
*Mar 8 00:03:07.046: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:07.046: RADIUS: 73 1D 89 5C 66 19 32 B6 63 C2 64 C1 04 42 A9 F9 [ s\f2cdB]
*Mar 8 00:03:07.046: RADIUS: EAP-Key-Name [102] 2 *
*Mar 8 00:03:07.046: RADIUS: Vendor, Cisco [26] 49
*Mar 8 00:03:07.046: RADIUS: Cisco AVpair [1] 43 "audit-session-id=0A1AED0B000000EE240F5BAB"
*Mar 8 00:03:07.046: RADIUS: NAS-Port-Type [61] 6 Ethernet [15]
*Mar 8 00:03:07.046: RADIUS: NAS-Port [5] 6 50001
*Mar 8 00:03:07.046: RADIUS: NAS-Port-Id [87] 17 "FastEthernet0/1"
*Mar 8 00:03:07.046: RADIUS: State [24] 30
*Mar 8 00:03:07.046: RADIUS: 00 6F 00 51 00 4B 00 6E EE B8 45 00 4B AA 6B A9 B6 D6 C8 CC 48 1A 91 99 7F 77 D3 C1 [ oQKnEKkHw]
*Mar 8 00:03:07.046: RADIUS: NAS-IP-Address [4] 6 10.26.237.11
*Mar 8 00:03:07.046: RADIUS: Acct-Session-Id [44] 10 "000002D4"
*Mar 8 00:03:07.046: RADIUS(000001C7): Started 3 sec timeout
*Mar 8 00:03:07.113: RADIUS: Received from id 1645/85 10.26.13.59:1812, Access-Challenge, len 378
*Mar 8 00:03:07.113: RADIUS: authenticator 1A 85 26 09 58 84 BC D4 - E0 A9 E3 C0 25 31 2D 31
*Mar 8 00:03:07.113: RADIUS: EAP-Message [79] 255
*Mar 8 00:03:07.121: RADIUS: 01 04 01 32 0D 00 66 69 63 61 74 65 20 41 75 74 68 6F 72 69 74 [2ficate Authorit]
*Mar 8 00:03:07.121: RADIUS: 79 20 28 53 69 67 6E 69 6E 67 29 31 3F 30 3D 06 09 2A [y (Signing)1?0=*]
*Mar 8 00:03:07.121: RADIUS: 86 48 86 F7 0D 01 09 01 16 30 64 36 62 62 34 66 37 30 2D 66 34 31 32 2D [H0d6bb4f70-f412-]
*Mar 8 00:03:07.121: RADIUS: 34 35 35 32 2D 61 65 65 32 2D 63 37 61 30 32 36 [4552-aee2-c7a026]
*Mar 8 00:03:07.121: RADIUS: 66 62 61 32 31 38 40 65 78 61 6D 70 6C 65 2E 63 [[email protected]]
*Mar 8 00:03:07.121: RADIUS: 6F 6D 00 CB 30 81 C8 31 0B 30 09 06 03 55 04 06 13 02 55 53 31 13 30 11 06 03 55 04 08 0C 0A 43 61 6C 69 66 [om010UUS10UCalif]
*Mar 8 00:03:07.121: RADIUS: 6F 72 6E 69 61 31 12 30 10 06 03 55 04 07 0C 09 53 75 6E 6E 79 76 61 6C [ornia10USunnyval]
*Mar 8 00:03:07.121: RADIUS: 65 31 17 30 15 06 03 55 04 0A 0C 0E 41 72 75 62 61 20 4E 65 74 77 6F 72 [e10UAruba Networ]
*Mar 8 00:03:07.121: RADIUS: 6B 73 31 36 30 34 06 03 55 04 03 0C 2D 43 6C 65 61 72 50 61 73 [ks1604U-ClearPas]
*Mar 8 00:03:07.121: RADIUS: 73 20 4F 6E 62 6F 61 72 64 20 4C 6F 63 61 6C 20 [s Onboard Local ]
*Mar 8 00:03:07.121: RADIUS: 43 65 72 74 69 66 69 63 61 74 65 20 41 75 74 68 [Certificate Auth]
*Mar 8 00:03:07.121: RADIUS: 6F 72 69 74 79 31 3F 30 3D 06 09 2A 86 48 86 F7 0D 01 09 01 16 [ ority1?0=*H]
*Mar 8 00:03:07.121: RADIUS: EAP-Message [79] 55
*Mar 8 00:03:07.121: RADIUS: 30 64 36 62 62 34 66 37 30 2D 66 34 31 32 2D 34 [0d6bb4f70-f412-4]
*Mar 8 00:03:07.121: RADIUS: 35 35 32 2D 61 65 65 32 2D 63 37 61 30 32 36 66 [552-aee2-c7a026f]
*Mar 8 00:03:07.121: RADIUS: 62 61 32 31 38 40 65 78 61 6D 70 6C 65 2E 63 6F [[email protected]]
*Mar 8 00:03:07.121: RADIUS: 6D 0E 00 00 00 [ m]
*Mar 8 00:03:07.121: RADIUS: Message-Authenticato[80] 18
*Mar 8 00:03:07.121: RADIUS: 4C 46 AA B9 A5 D5 DF EA DB E7 2B 7B 51 7E 58 3F [ LF+{Q~X?]
*Mar 8 00:03:07.121: RADIUS: State [24] 30
*Mar 8 00:03:07.121: RADIUS: 00 EF 00 B9 00 0A 00 00 EF B8 45 00 EF D2 C4 3C 81 6C 72 0E 23 FE 11 EA 12 17 50 A1 [ E
*Mar 8 00:03:07.121: RADIUS(000001C7): Received from id 1645/85
*Mar 8 00:03:07.121: RADIUS/DECODE: EAP-Message fragments, 253+53, total 306 bytes
*Mar 8 00:03:07.130: dot1x-sm(Fa0/1): Posting EAP_REQ for 0xB0000DBA
*Mar 8 00:03:07.130: dot1x_auth_bend Fa0/1: during state auth_bend_response, got event 7(eapReq)
*Mar 8 00:03:07.130: @@@ dot1x_auth_bend Fa0/1: auth_bend_response -> auth_bend_request
*Mar 8 00:03:07.130: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_exit called
*Mar 8 00:03:07.130: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_request_enter called
*Mar 8 00:03:07.130: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:07.130: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:07.130: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:07.130: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:07.130: EAPOL pak dump Tx
*Mar 8 00:03:07.130: EAPOL Version: 0x3 type: 0x0 length: 0x0132
*Mar 8 00:03:07.130: EAP code: 0x1 id: 0x4 length: 0x0132 type: 0xD
*Mar 8 00:03:07.130: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:07.130: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_request_action called
*Mar 8 00:03:07.138: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:07.138: dot1x-packet(Fa0/1): Queuing an EAPOL pkt on Authenticator Q
*Mar 8 00:03:07.138: dot1x-ev:Enqueued the eapol packet to the global authenticator queue
*Mar 8 00:03:07.138: EAPOL pak dump rx
*Mar 8 00:03:07.138: EAPOL Version: 0x1 type: 0x0 length: 0x05D4
*Mar 8 00:03:07.138: dot1x-ev:
dot1x_auth_queue_event: Int Fa0/1 CODE= 2,TYPE= 13,LEN= 1492
*Mar 8 00:03:07.138: dot1x-packet(Fa0/1): Received an EAPOL frame
*Mar 8 00:03:07.138: dot1x-ev(Fa0/1):
^Z
Malleswaram_2960#
*Mar 8 00:03:07.180: RADIUS: State [24] 30
*Mar 8 00:03:07.180: RADIUS: 00 EF 00 B9 00 0A 00 00 EF B8 45 00 EF D2 C4 3C 81 6C 72 0E 23 FE 11 EA 12 17 50 A1 [ E
*Mar 8 00:03:07.180: RADIUS: NAS-IP-Address [4] 6 10.26.237.11
*Mar 8 00:03:07.180: RADIUS: Acct-Session-Id [44] 10 "000002D4"
*Mar 8 00:03:07.180: RADIUS(000001C7): Started 3 sec timeout
Malleswaram_2960#
*Mar 8 00:03:07.893: %SYS-5-CONFIG_I: Configured from console by jameela on vty0 (10.26.20.5)
Malleswaram_2960#
*Mar 8 00:03:10.225: RADIUS(000001C7): Request timed out
*Mar 8 00:03:10.225: RADIUS: Retransmit to (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:10.225: RADIUS(000001C7): Started 3 sec timeout
Malleswaram_2960#
*Mar 8 00:03:13.354: RADIUS(000001C7): Request timed out
*Mar 8 00:03:13.354: RADIUS: Retransmit to (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:13.354: RADIUS(000001C7): Started 3 sec timeout
Malleswaram_2960#
*Mar 8 00:03:16.307: RADIUS(000001C7): Request timed out
*Mar 8 00:03:16.307: RADIUS: Retransmit to (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:16.307: RADIUS(000001C7): Started 3 sec timeout
Malleswaram_2960#
*Mar 8 00:03:19.369: RADIUS(000001C7): Request timed out
*Mar 8 00:03:19.369: RADIUS: Retransmit to (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:19.369: RADIUS(000001C7): Started 3 sec timeout
Malleswaram_2960#
*Mar 8 00:03:22.456: RADIUS(000001C7): Request timed out
*Mar 8 00:03:22.456: RADIUS: Fail-over denied to (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:22.456: RADIUS: No response from (10.26.13.59:1812,1813) for id 1645/86
*Mar 8 00:03:22.456: RADIUS/DECODE: parse response no app start; FAIL
*Mar 8 00:03:22.456: RADIUS/DECODE: parse response; FAIL
*Mar 8 00:03:22.456: dot1x-ev(Fa0/1): Received an EAP Fail
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): Posting EAP_FAIL for 0xB0000DBA
*Mar 8 00:03:22.456: dot1x_auth_bend Fa0/1: during state auth_bend_response, got event 10(eapFail)
*Mar 8 00:03:22.456: @@@ dot1x_auth_bend Fa0/1: auth_bend_response -> auth_bend_fail
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_exit called
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_fail_enter called
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_response_fail_action called
*Mar 8 00:03:22.456: dot1x_auth_bend Fa0/1: idle during state auth_bend_fail
*Mar 8 00:03:22.456: @@@ dot1x_auth_bend Fa0/1: auth_bend_fail -> auth_bend_idle
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_bend_idle_enter called
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): Posting AUTH_FAIL on Client 0xB0000DBA
*Mar 8 00:03:22.456: dot1x_auth Fa0/1: during state auth_authenticating, got event 15(authFail)
*Mar 8 00:03:22.456: @@@ dot1x_auth Fa0/1: auth_authenticating -> auth_authc_result
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authenticating_exit called
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_authc_result_enter called
*Mar 8 00:03:22.456: %DOT1X-5-FAIL: Authentication failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID
*Mar 8 00:03:22.456: dot1x-ev(Fa0/1): Sending event (2) to Auth Mgr for d43d.7e65.4fc1
*Mar 8 00:03:22.456: %AUTHMGR-7-RESULT: Authentication result 'fail' from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EE240F5BAB
*Mar 8 00:03:22.456: %AUTHMGR-5-FAIL: Authorization failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EE240F5BAB
*Mar 8 00:03:22.456: dot1x-redundancy: State for client d43d.7e65.4fc1 successfully retrieved
*Mar 8 00:03:22.456: dot1x-ev(Fa0/1): Received Authz fail for the client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): Posting_AUTHZ_FAIL on Client 0xB0000DBA
*Mar 8 00:03:22.456: dot1x_auth Fa0/1: during state auth_authc_result, got event 22(authzFail)
*Mar 8 00:03:22.456: @@@ dot1x_auth Fa0/1: auth_authc_result -> auth_held
*Mar 8 00:03:22.456: dot1x-sm(Fa0/1): 0xB0000DBA:auth_held_enter called
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:22.464: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:22.464: EAPOL pak dump Tx
*Mar 8 00:03:22.464: EAPOL Version: 0x3 type: 0x0 length: 0x0004
*Mar 8 00:03:22.464: EAP code: 0x4 id: 0x4 length: 0x0004
*Mar 8 00:03:22.464: dot1x-packet(Fa0/1): EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): Posting FAILOVER_RETRY on Client 0xB0000DBA
*Mar 8 00:03:22.464: dot1x_auth Fa0/1: during state auth_held, got event 21(failover_retry)
*Mar 8 00:03:22.464: @@@ dot1x_auth Fa0/1: auth_held -> auth_restart
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_held_exit called
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_enter called
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending create new context event to EAP for 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_held_restart_action called
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): Posting !EAP_RESTART on Client 0xB0000DBA
*Mar 8 00:03:22.464: dot1x_auth Fa0/1: during state auth_restart, got event 6(no_eapRestart)
*Mar 8 00:03:22.464: @@@ dot1x_auth Fa0/1: auth_restart -> auth_connecting
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_enter called
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_restart_connecting_action called
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): Posting REAUTH_MAX on Client 0xB0000DBA
*Mar 8 00:03:22.464: dot1x_auth Fa0/1: during state auth_connecting, got event 11(reAuthMax)
*Mar 8 00:03:22.464: @@@ dot1x_auth Fa0/1: auth_connecting -> auth_disconnected
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_disconnected_enter called
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): d43d.7e65.4fc1:auth_disconnected_enter sending canned failure to version 1 supplicant
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:22.464: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:22.464: EAPOL pak dump Tx
*Mar 8 00:03:22.464: EAPOL Version: 0x3 type: 0x0 length: 0x0004
*Mar 8 00:03:22.464: EAP code: 0x4 id: 0x5 length: 0x0004
*Mar 8 00:03:22.464: dot1x-packet(Fa0/1): dot1x_auth_txCannedStatus: EAPOL packet sent to client 0xB0000DBA (d43d.7e65.4fc1)
*Mar 8 00:03:22.464: dot1x-sm(Fa0/1): 0xB0000DBA:auth_connecting_disconnected_reAuthMax_action called
*Mar 8 00:03:22.464: dot1x_auth Fa0/1: idle during state auth_disconnected
*Mar 8 00:03:22.464: @@@ dot1x_auth Fa0/1: auth_disconnected -> auth_restart
*Mar 8 00:03:22.464: dot1x-ev(Fa0/1): Sending event (1) to Auth Mgr for d43d.7e65.4fc1
*Mar 8 00:03:22.464: dot1x-ev:Delete auth client (0xB0000DBA) message
*Mar 8 00:03:22.464: dot1x-ev:Auth client ctx destroyed
*Mar 8 00:03:22.674: AAA/BIND(000001C8): Bind i/f
*Mar 8 00:03:22.674: dot1x_auth Fa0/1: initial state auth_initialize has enter
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_initialize_enter called
*Mar 8 00:03:22.674: dot1x_auth Fa0/1: during state auth_initialize, got event 0(cfg_auto)
*Mar 8 00:03:22.674: @@@ dot1x_auth Fa0/1: auth_initialize -> auth_disconnected
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_disconnected_enter called
*Mar 8 00:03:22.674: dot1x_auth Fa0/1: idle during state auth_disconnected
*Mar 8 00:03:22.674: @@@ dot1x_auth Fa0/1: auth_disconnected -> auth_restart
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_restart_enter called
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Sending create new context event to EAP for 0x4A000DBB (0000.0000.0000)
*Mar 8 00:03:22.674: dot1x_auth_bend Fa0/1: initial state auth_bend_initialize has enter
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_initialize_enter called
*Mar 8 00:03:22.674: dot1x_auth_bend Fa0/1: initial state auth_bend_initialize has idle
*Mar 8 00:03:22.674: dot1x_auth_bend Fa0/1: during state auth_bend_initialize, got event 16383(idle)
*Mar 8 00:03:22.674: @@@ dot1x_auth_bend Fa0/1: auth_bend_initialize -> auth_bend_idle
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_idle_enter called
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Created a client entry (0x4A000DBB)
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Dot1x authentication started for 0x4A000DBB (0000.0000.0000)
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): Posting !EAP_RESTART on Client 0x4A000DBB
*Mar 8 00:03:22.674: dot1x_auth Fa0/1: during state auth_restart, got event 6(no_eapRestart)
*Mar 8 00:03:22.674: @@@ dot1x_auth Fa0/1: auth_restart -> auth_connecting
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_connecting_enter called
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_restart_connecting_action called
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): Posting RX_REQ on Client 0x4A000DBB
*Mar 8 00:03:22.674: dot1x_auth Fa0/1: during state auth_connecting, got event 10(eapReq_no_reAuthMax)
*Mar 8 00:03:22.674: @@@ dot1x_auth Fa0/1: auth_connecting -> auth_authenticating
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_authenticating_enter called
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_connecting_authenticating_action called
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): Posting AUTH_START for 0x4A000DBB
*Mar 8 00:03:22.674: dot1x_auth_bend Fa0/1: during state auth_bend_idle, got event 4(eapReq_authStart)
*Mar 8 00:03:22.674: @@@ dot1x_auth_bend Fa0/1: auth_bend_idle -> auth_bend_request
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_enter called
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Role determination not required
Malleswaram_2960#
*Mar 8 00:03:22.674: dot1x-registry:registry:dot1x_ether_macaddr called
*Mar 8 00:03:22.674: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:22.674: EAPOL pak dump Tx
*Mar 8 00:03:22.674: EAPOL Version: 0x3 type: 0x0 length: 0x0005
*Mar 8 00:03:22.674: EAP code: 0x1 id: 0x1 length: 0x0005 type: 0x1
*Mar 8 00:03:22.674: dot1x-packet(Fa0/1): EAPOL packet sent to client 0x4A000DBB (0000.0000.0000)
*Mar 8 00:03:22.674: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_idle_request_action called
*Mar 8 00:03:22.791: dot1x-ev(Fa0/1): New client notification from AuthMgr for 0x4A000DBB - d43d.7e65.4fc1
*Mar 8 00:03:22.791: %AUTHMGR-5-START: Starting 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:03:25.761: dot1x-sm(Fa0/1): Posting EAP_REQ for 0x4A000DBB
*Mar 8 00:03:25.761: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 7(eapReq)
*Mar 8 00:03:25.761: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_request
*Mar 8 00:03:25.761: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_request_action called
*Mar 8 00:03:25.761: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_enter called
*Mar 8 00:03:25.761: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:25.761: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:25.761: dot1x-registry:registry:dot1x_ether_macaddr called
Malleswaram_2960#n
*Mar 8 00:03:25.761: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:25.761: EAPOL pak dump Tx
*Mar 8 00:03:25.761: EAPOL Version: 0x3 type: 0x0 length: 0x0005
*Mar 8 00:03:25.761: EAP code: 0x1 id: 0x1 length: 0x0005 type: 0x1
*Mar 8 00:03:25.761: dot1x-packet(Fa0/1): EAPOL packet sent to client 0x4A000DBB (d43d.7e65.4fc1)
Malleswaram_2960#no debu
Malleswaram_2960#no debug
*Mar 8 00:03:28.848: dot1x-sm(Fa0/1): Posting EAP_REQ for 0x4A000DBB
*Mar 8 00:03:28.848: dot1x_auth_bend Fa0/1: during state auth_bend_request, got event 7(eapReq)
*Mar 8 00:03:28.848: @@@ dot1x_auth_bend Fa0/1: auth_bend_request -> auth_bend_request
*Mar 8 00:03:28.848: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_request_action called
*Mar 8 00:03:28.848: dot1x-sm(Fa0/1): 0x4A000DBB:auth_bend_request_enter called
*Mar 8 00:03:28.848: dot1x-ev(Fa0/1): Sending EAPOL packet to group PAE address
*Mar 8 00:03:28.848: dot1x-ev(Fa0/1): Role determination not required
*Mar 8 00:03:28.848: dot1x-registry:registry:dot1x_ether_macaddr called
Malleswaram_2960#no debug all
*Mar 8 00:03:28.848: dot1x-ev(Fa0/1): Sending out EAPOL packet
*Mar 8 00:03:28.848: EAPOL pak dump Tx
*Mar 8 00:03:28.848: EAPOL Version: 0x3 type: 0x0 length: 0x0005
*Mar 8 00:03:28.848: EAP code: 0x1 id: 0x1 length: 0x0005 type: 0x1
*Mar 8 00:03:28.848: dot1x-packet(Fa0/1): EAPOL packet sent to client 0x4A000DBB (d43d.7e65.4fc1)
Malleswaram_2960#no debug all
All possible debugging has been turned off
Malleswaram_2960#
*Mar 8 00:03:31.180: AAA: parse name=tty1 idb type=-1 tty=-1
*Mar 8 00:03:31.180: AAA: name=tty1 flags=0x11 type=5 shelf=0 slot=0 adapter=0 port=1 channel=0
*Mar 8 00:03:31.180: AAA/MEMORY: create_user (0x21D1684) user='jameela' ruser='Malleswaram_2960' ds0=0 port='tty1' rem_addr='10.26.20.5' authen_type=ASCII service=NONE priv=15 initial_task_id='0', vrf= (id=0) key=C9A1F1D1
*Mar 8 00:03:31.389: TAC+: (-1901802859): received author response status = PASS_ADD
*Mar 8 00:03:31.389: AAA/MEMORY: free_user (0x21D1684) user='jameela' ruser='Malleswaram_2960' port='tty1' rem_addr='10.26.20.5' authen_type=ASCII service=NONE priv=15
*Mar 8 00:03:31.935: %DOT1X-5-FAIL: Authentication failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID
*Mar 8 00:03:31.935: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:03:31.935: %AUTHMGR-7-FAILOVER: Failing over from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:03:31.935: %AUTHMGR-7-NOMOREMETHODS: Exhausted all authentication methods for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:03:31.935: %AUTHMGR-5-FAIL: Authorization failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#no deb
Malleswaram_2960#no debug al
Malleswaram_2960#no debug all
All possible debugging has been turned off
Malleswaram_2960#
*Mar 8 00:04:32.677: %AUTHMGR-5-START: Starting 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:04:41.938: %DOT1X-5-FAIL: Authentication failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID
*Mar 8 00:04:41.938: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:04:41.938: %AUTHMGR-7-FAILOVER: Failing over from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:04:41.938: %AUTHMGR-7-NOMOREMETHODS: Exhausted all authentication methods for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:04:41.938: %AUTHMGR-5-FAIL: Authorization failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:05:42.654: %AUTHMGR-5-START: Starting 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:05:51.915: %DOT1X-5-FAIL: Authentication failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID
*Mar 8 00:05:51.915: %AUTHMGR-7-RESULT: Authentication result 'no-response' from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:05:51.915: %AUTHMGR-7-FAILOVER: Failing over from 'dot1x' for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
*Mar 8 00:05:51.915: %AUTHMGR-7-NOMOREMETHODS: Exhausted all authentication methods for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Malleswaram_2960#
*Mar 8 00:05:51.915: %AUTHMGR-5-FAIL: Authorization failed for client (d43d.7e65.4fc1) on Interface Fa0/1 AuditSessionID 0A1AED0B000000EF240F9BC3
Pls dont worry about day and time. -
Cisco 1941 Router-on-a-Stick w/ 11VLANs trunked to a Cisco 2960: From the Switch I can Ping a device in another VLAN, that device cannot ping back. Some devices can ping devices in other VLANs and the device in the other VLAN can successfully return the Ping. Have a look at the attached diagram.
Router Config:
show run
Building configuration...
Current configuration : 7224 bytes
! Last configuration change at 09:05:48 EDT Wed Aug 6 2014
version 15.2
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname ROUTER
boot-start-marker
boot-end-marker
no aaa new-model
clock timezone EDT -8 0
ip cef
ip name-server 8.8.8.8
no ipv6 cef
multilink bundle-name authenticated
license udi pid CISCO1941/K9
object-group network Net_Obj_Group1
description This network group allows all 10.0.0.0 and Email Forwarder server through to the Plt PCs
205.191.0.0 255.255.0.0
10.0.0.0 255.0.0.0
object-group network Net_Obj_Group2
description This Network Group includes the Host IPs allowed through the Plant Router
host 10.194.28.23
host 10.194.28.25
host 10.194.28.26
host 10.194.28.27
host 10.194.28.28
host 10.194.28.29
host 10.194.28.37
host 10.194.28.39
host 10.194.28.40
host 10.194.28.70
host 10.194.28.130
host 10.194.28.131
host 10.194.28.132
host 10.194.28.133
host 10.194.28.134
host 10.194.28.135
host 10.194.28.136
host 10.194.28.137
host 10.194.28.138
host 10.194.28.139
host 10.194.28.140
host 10.194.28.141
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description Port Ge0/0 to IT Enterprise network Switch GE1/0/38
ip address 10.194.28.111 255.255.255.0
ip access-group 105 in
ip access-group 106 out
ip nat outside
ip virtual-reassembly in
shutdown
duplex full
speed auto
no mop enabled
interface GigabitEthernet0/1
description Port to Plant PCN-K/L24 Sw1 Port 0/24
no ip address
duplex auto
speed auto
no mop enabled
interface GigabitEthernet0/1.102
description Port to VLAN 102
encapsulation dot1Q 102
ip address 192.168.102.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.104
description Port to VLAN 104
encapsulation dot1Q 104
ip address 192.168.104.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.105
description Port to VLAN 105
encapsulation dot1Q 105
ip address 192.168.105.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.106
description Port to VLAN 106
encapsulation dot1Q 106
ip address 192.168.106.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.107
description Port to VLAN 107
encapsulation dot1Q 107
ip address 192.168.107.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.111
description Port to VLAN 111
encapsulation dot1Q 111
ip address 192.168.111.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.117
description Port to VLAN 117
encapsulation dot1Q 117
ip address 192.168.117.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.121
description Port to VLAN 121
encapsulation dot1Q 121
ip address 192.168.121.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.125
description Port to VLAN 125
encapsulation dot1Q 125
ip address 192.168.125.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.150
description Port to to VLAN 150
encapsulation dot1Q 150
ip address 192.168.150.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/1.999
description Port to VLAN 999
encapsulation dot1Q 999
ip address 192.168.0.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip forward-protocol nd
ip http server
no ip http secure-server
ip nat inside source static 192.168.102.201 10.194.28.23
ip nat inside source static 192.168.121.201 10.194.28.25
ip nat inside source static 192.168.106.251 10.194.28.26
ip nat inside source static 192.168.107.245 10.194.28.27
ip nat inside source static 192.168.102.251 10.194.28.28
ip nat inside source static 192.168.150.201 10.194.28.29
ip nat inside source static 192.168.107.179 10.194.28.37
ip nat inside source static 192.168.111.201 10.194.28.39
ip nat inside source static 192.168.105.201 10.194.28.40
ip nat inside source static 192.168.106.21 10.194.28.70
ip nat inside source static 192.168.107.146 10.194.28.130
ip nat inside source static 192.168.107.156 10.194.28.131
ip nat inside source static 192.168.107.161 10.194.28.132
ip nat inside source static 192.168.107.181 10.194.28.133
ip nat inside source static 192.168.107.191 10.194.28.134
ip nat inside source static 192.168.106.202 10.194.28.135
ip nat inside source static 192.168.106.212 10.194.28.136
ip nat inside source static 192.168.117.190 10.194.28.137
ip nat inside source static 192.168.117.100 10.194.28.138
ip nat inside source static 192.168.106.242 10.194.28.139
ip nat inside source static 192.168.125.100 10.194.28.140
ip nat inside source static 192.168.125.99 10.194.28.141
ip nat outside source static 10.194.28.23 10.194.28.23
ip nat outside source static 10.194.28.25 10.194.28.25
ip nat outside source static 10.194.28.26 10.194.28.26
ip nat outside source static 10.194.28.27 10.194.28.27
ip nat outside source static 10.194.28.28 10.194.28.28
ip nat outside source static 10.194.28.29 10.194.28.29
ip nat outside source static 10.194.28.37 10.194.28.37
ip nat outside source static 10.194.28.39 10.194.28.39
ip nat outside source static 10.194.28.40 10.194.28.40
ip nat outside source static 10.194.28.70 10.194.28.70
ip nat outside source static 10.194.28.130 10.194.28.130
ip nat outside source static 10.194.28.131 10.194.28.131
ip nat outside source static 10.194.28.132 10.194.28.132
ip nat outside source static 10.194.28.133 10.194.28.133
ip nat outside source static 10.194.28.134 10.194.28.134
ip nat outside source static 10.194.28.135 10.194.28.135
ip nat outside source static 10.194.28.136 10.194.28.136
ip nat outside source static 10.194.28.137 10.194.28.137
ip nat outside source static 10.194.28.138 10.194.28.138
ip nat outside source static 10.194.28.139 10.194.28.139
ip nat outside source static 10.194.28.140 10.194.28.140
ip nat outside source static 10.194.28.141 10.194.28.141
ip route 0.0.0.0 0.0.0.0 10.194.28.1
access-list 105 permit ip object-group Net_Obj_Group1 object-group Net_Obj_Group2
access-list 106 permit ip object-group Net_Obj_Group2 object-group Net_Obj_Group1
dialer-list 1 protocol ip permit
control-plane
banner login ^CC
Login banner for Plant Router #01^C
banner motd ^CC
MOTD Banner for Plant Router^C
line con 0
password XXXXXXXXX
logging synchronous
login
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
password XXXXXXXXX
logging synchronous
login
transport input all
scheduler allocate 20000 1000
ntp server 10.199.100.92
end
Switch Config:
sh ru
Building configuration...
Current configuration : 6513 bytes
version 12.2
no service pad
service timestamps debug uptime
service timestamps log datetime localtime show-timezone
service password-encryption
hostname K24Sw01
boot-start-marker
boot-end-marker
no aaa new-model
clock timezone EDT -5
clock summer-time EDT recurring
udld aggressive
crypto pki trustpoint TP-self-signed-593746944
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-593746944
revocation-check none
rsakeypair TP-self-signed-593746944
4B58BCE9 44
quit
spanning-tree mode pvst
spanning-tree extend system-id
vlan internal allocation policy ascending
interface FastEthernet0
no ip address
interface GigabitEthernet0/1
description Trunk port for vlans 105, 111, 125 and 999 from K24Sw01 port Ge0/1 to P22Sw01 port Ge0/24
switchport trunk allowed vlan 105,111,125,999
switchport mode trunk
interface GigabitEthernet0/2
description Trunk port for vlans 150 and 999 from K24Sw01 port Ge0/2 to N25Sw01 port Ge0/26
switchport trunk allowed vlan 150,999
switchport mode trunk
interface GigabitEthernet0/3
description Trunk port for vlans 102, 104, 106, 107, 117 and 999 from K24Sw01 port Ge0/3 to K28Sw01 port Ge0/26
switchport trunk allowed vlan 102,104,106,107,117,999
switchport mode trunk
interface GigabitEthernet0/4
description Trunk port for vlans 102, 106, 107 and 999 from K24Sw01 port Ge0/4 to H23Sw01 port Ge0/26
switchport trunk allowed vlan 102,106,107,999
switchport mode trunk
interface GigabitEthernet0/5
description Trunk port for vlans 121, 125 and 999 from K24Sw01 port Ge0/5 to M21Sw01 port Ge0/24
switchport trunk allowed vlan 121,125,999
switchport mode trunk
interface GigabitEthernet0/6
description OPEN
spanning-tree portfast
interface GigabitEthernet0/7
description OPEN
spanning-tree portfast
interface GigabitEthernet0/8
description OPEN
spanning-tree portfast
interface GigabitEthernet0/9
description OPEN
spanning-tree portfast
interface GigabitEthernet0/10
description VLan 102 access port
switchport access vlan 102
spanning-tree portfast
interface GigabitEthernet0/11
description - VLan 104 access port
switchport access vlan 104
spanning-tree portfast
interface GigabitEthernet0/12
description - VLan 105 access port
switchport access vlan 105
spanning-tree portfast
interface GigabitEthernet0/13
description - VLan 106 access port
switchport access vlan 106
spanning-tree portfast
interface GigabitEthernet0/14
description - VLan 107 access port
switchport access vlan 107
spanning-tree portfast
interface GigabitEthernet0/15
description - VLan 111 access port
switchport access vlan 111
spanning-tree portfast
interface GigabitEthernet0/16
description - VLan 117 access port
switchport access vlan 117
spanning-tree portfast
interface GigabitEthernet0/17
description - VLan 121 access port
switchport access vlan 121
spanning-tree portfast
interface GigabitEthernet0/18
description - VLan 125 access port
switchport access vlan 125
spanning-tree portfast
interface GigabitEthernet0/19
description - VLan 150 access port
switchport access vlan 150
spanning-tree portfast
interface GigabitEthernet0/20
description - VLan 999 access port
switchport access vlan 999
spanning-tree portfast
interface GigabitEthernet0/21
description OPEN
spanning-tree portfast
interface GigabitEthernet0/22
description OPEN
spanning-tree portfast
interface GigabitEthernet0/23
description OPEN
spanning-tree portfast
interface GigabitEthernet0/24
description From ROUTER Gw ge0/1
switchport trunk allowed vlan 102,104-107,111,117,121,125,150,999
switchport mode trunk
interface GigabitEthernet0/25
interface GigabitEthernet0/26
interface Vlan1
no ip address
no ip route-cache
shutdown
interface Vlan102
ip address 192.168.102.253 255.255.255.0
interface Vlan104
no ip address
no ip route-cache
interface Vlan105
no ip address
no ip route-cache
interface Vlan106
no ip address
no ip route-cache
interface Vlan107
no ip address
no ip route-cache
interface Vlan111
no ip address
no ip route-cache
interface Vlan117
no ip address
no ip route-cache
interface Vlan121
no ip address
no ip route-cache
interface Vlan125
no ip address
no ip route-cache
interface Vlan150
no ip address
no ip route-cache
interface Vlan999
no ip address
no ip route-cache
ip default-gateway 192.168.102.1
ip http server
ip http secure-server
snmp-server engineID local 00000009020000019634C2C0
snmp-server community public RO
snmp-server location
snmp-server contact
banner motd ^CCC ADMIN USE ONLY! ^C
line con 0
session-timeout 10
password xxxxxx
logging synchronous
login
stopbits 1
line vty 0 4
session-timeout 10
password xxxxxxx
login
line vty 5 15
session-timeout 10
password xxxxxxxx
login
ntp server 10.199.100.92
end
K24Sw01#HI Mark,
Here is the my config:
Create sub-interfaces, set 802.1Q trunking protocol and ip address on each sub-interface
Router(config)#interface f0/0
Router(config-if)#no shutdown
(Note: The main interface f0/0 doesn’t need an IP address but it must be turned on)
Router(config)#interface f0/0.10
Router(config-subif)#encapsulation dot1q 10
Router(config-subif)#ip address 192.168.10.1 255.255.255.0
Router(config-subif)#interface f0/0.20
Router(config-subif)#encapsulation dot11 20
Router(config-subif)#ip address 192.168.20.1 255.255.255.0
(Note: In the “encapsulation dot1q 10″ command, 10 is the VLAN ID this interface operates in)
Configure VLAN
Switch(config)#vlan 10
Switch(config-vlan)#name SALES
Switch(config-vlan)#vlan 20
Switch(config-vlan)#name TECH
Set ports to access mode & assign ports to VLAN
Switch(config)#interface range fa0/1
Switch(config-if)#no shutdown
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 15
Switch(config-if)#interface range fa0/3
Switch(config-if)#no shutdown
Switch(config-if)#switchport mode access
Switch(config-if)# switchport access vlan 20
Switch(config-if)#interface range fa0/5
Switch(config-if)#no shutdown
Switch(config-if)#switchport mode trunk
1. Please check all your port are up.
2. Check the config once again.
3. Make sure the swicth and router connection port configured as trunk and it should be up.
This config is working for me,
Regards
Dont forget to rate helpful posts. -
Hi,
We are using CISCO 3750-G Switch as Core Switch. VLAN1 is being our Native VLAN since the implementation.
This switch is connected with 10 numbers of CISCO 2960 Switches by trunking ports. IP addresses assigned for L2 Switches from VLAN1 only.
Now I want to change the Default Native VLAN from 1 to some other.
My query is is there any pre-requesties to change Native VLAN or Can I change to Native VLAN ID simply?
Looking forward support.
Regards,
Ramesh BalachandranHI Ramesh,
Native VLAN will come into picture if you use trunks in your switches. Procedure to change the native VLAN.
1) conf ter
interface
switchport trunk native vlan
CAUTION: If you are chaning the native VLAN only one end the spanning-tree for the orginal native vlan and the changed native vlan will go into inconsistency state and will be blocked.
In the below example on the local end(Native VLAN chosen is 2 and the remote end is 1)
3750#sh spanning-tree int gi1/8
Vlan Role Sts Cost Prio.Nbr Type
VLAN0001 Desg BKN*4 128.8 P2p *PVID_Inc
VLAN0002 Desg BKN*4 128.8 P2p *PVID_Inc
Thanks & Regards,
Karthick Murugan
CCIE#39285 -
Slow download performance with windows 7 on Cisco 2960S
has someone experience with the the windows 7 on Cisco 2960S.
One customer had the issue with very slow download rate ( 500kByte) with 100MB / full duplex and default tcp paramenter under win 7 with IOS 12.2.55SE1.
No error was seen.
The change of follwing in windows improve the performance a litte bit to 1-2 MByte.
no compression, no tcp windowing, no received side scaling, no windows side heuristic, no checksum offloading and a smaller MTU size than default.
After update the Switch to 12.2.55.SE2 the performance imporve to 4-12 MByte.
Has someone an idea about the chances in IOS 12.2.55SE2. I cant find anything in RN about this issue.
Best regards
SteffenI have the same issues in WS-C2960G-48TC-L . my downloads dropped in my lan from 2 mb/s to 100kb/s in all operating systems including linux workstations . my ios version is 12.2(44)SE5 in 2960 switches .
i have 2 x 4503-E L3 and 14 2960-48TC-L switches but i can not access the new ios versions to test if the issue is coming from ios version because of end of support .
can someone ensure that the new ios remove this issue ? -
Default username and password Oracle Hyperion workspace/shared services
Hi Friends,
I had installed Install Oracle Hyperion Planning, Fusion Edition Release 11.1.1.3.0 (foundation services and planning)
but i am unable to login to workspace,shared services
what is the default username and password for these.Please let me know?
Regards,
DBHi,
Default Admin user is: admin and default PW: password.
If you have not yet changed.
Thanks
Focusthread Hyperion Trainer
[http://focusthread.com/training] -
When asking for username and password the default username is wrong
I have had a look through all the posts here but I can't find anything that helps me. I don't want to actually change my username or reset my password. I know what they both are; however...
I have a recently had to replace my hard drive and now have a fresh install of Snow Leopard. When installing programs the typical enter username and password box pops up but the default username which is populated there is wrong. I have to change it every time before I enter my password. I don't know why this is happening all of a sudden.
For example my username is xxxxyyyy but it comes up as Xxxx Yyyy (note the space). If I enter my password without changing it it gives me an error. If I enter it correctly everything works fine.
This is more of an annoyance than anything. Where/how do I change the default username that is entered into that box.
Any help would be much appreciated.I was able to change the default account login on my mac --
Go to System Preferences => System => Accounts & click on the lock to make changes.
Highlight the account you want to change & click on the Password tab on the right.
In the box that says Full Name type in your name the way you want it and hit enter.
Reboot you mac.
Your changed name should now be listed as default.
Rick -
BPM Default username and password
Hi Experts,
Will anyone please help to find the bpm composer default username and password to log into bpm composer. i installed bpm and trying to login with weblogic/welcome1. response is invalid ID and password. please help me out.
Thanks
SNUsually you have to set the standard weblogic username and password at install time. Common "default" combinations are weblogic/weblogic1, weblogic/welcome123, weblogic/welcome1, weblogic/oracle, weblogic/oracle123. But there really is no "default" as it is dependent on whatever you have indicated during the install. Many prebuilt VMs from Oracle will use one of the combinations that I mentioned though.
But if none of those work, you can change the weblogic password in WLS console --> Security Realms --> myrealm --> Users and Groups as already mentioned by the previous reply. -
Login Hook stops working once I've changed the username
Hello. I need to change the usernames for a number of local accounts on a 10.5.8 mac. The accounts were set up by someone else who is no longer working at this education insitution and hasn't left any documentation. Currently when each user logs on, a script runs that does the following
#!/usr/bin/env bash
# iMac logon script
# get our user
theUser=$1
# get the users home directory
#theUsersHome=$HOME
# Copy the dock plist file for the user
cp /Library/Scripts/GHS/Docks/${theUser}/com.apple.dock.plist /Users/${theUser}/Library/Preferences
# Create a ScreenCaptures folder on the desktop, give it permissions and redirect the screen captures
# Unlock the Desktop folder first in case it is locked
sudo chflags nouchg /Users/${theUser}/Desktop
mkdir /Users/${theUser}/Desktop/ScreenCaptures
sudo chown ${theUser}:staff /Users/${theUser}/Desktop/ScreenCaptures
defaults write com.apple.screencapture location /Users/${theUser}/Desktop/ScreenCaptures
# Create a VideoWork folder on the Desktop and give it permissions
# Unlock the Desktop folder first in case it is locked
sudo chflags nouchg /Users/${theUser}/Desktop
# Remove the old Video Work folder in case it exists
rmdir /Users/${theUser}/Desktop/Video\ Work
mkdir /Users/${theUser}/Desktop/VideoWork
sudo chown ${theUser}:staff /Users/${theUser}/Desktop/VideoWork
# Lock the Desktop, Documents, Movies, Music and Pictures folders
sudo chflags uchg /Users/${theUser}/Desktop
sudo chflags uchg /Users/${theUser}/Documents
sudo chflags uchg /Users/${theUser}/Movies
sudo chflags uchg /Users/${theUser}/Music
sudo chflags uchg /Users/${theUser}/Pictures
However, once I change the users account name, the script doesn't seem to run correctly as the screen captures fail due to not having write permission in the intended destination.
I rename the UserName the ShortName, the HomeDirectory and the folder here /Library/Scripts/GHS/Docks/UserName
The idea is, once I've updated this one mac with all the new accounts, I will then duplicate the image across all the others that we have
I'm very new to this and I'm not sure how much of this works
Thank you very much for any help and I apologise if I've missed out any essential information.Hi John, not certain I can help here, but...
Add a user from the OS X command line, works with Leopard!
http://osxdaily.com/2007/10/29/how-to-add-a-user-from-the-os-x-command-line-work s-with-leopard/
More...
http://osxdaily.com/2011/05/20/change-short-name-user-mac-os-x/
http://www.macworld.com/article/132693/2008/03/changeshortusername.html -
Aironet 1100 Default Username and Password not working
I have a Cisco Aironet 1100 series access point (AP1120B) that after resetting to factory defaults the default username and password (Cisco and Cisco) aren't working in the web GUI. I am able to telnet to the AP's IP and log in with Cisco and Cisco but don't know the ENABLE password. I have tried Cisco and cisco and everything else i could think of with no luck. any help would be appreciated.
I also have a Cisco Aironet AP1242AG that is doing the same thing.Hi Rich,
I assume that you are using the mode button to reset the configurations on these units -- this procedure *should* reset all credentials to Cisco.
If this is still not working, you can try the following:
1) Connect console port and power-cycle unit
2) When IOS starts loading, hit ESC key twice to get to the boot-loader prompt
3) At the boot-loader prompt show a directory of the flash filesystem (dir flash:)
4) Delete or rename the files "config.txt" and "env_vars", then boot the system ("delete flash:/config.txt" "delete flash:/env_vars")
-Patrick Croak
Wireless TAC -
Default Username and Password for Sample Packages
Hello,
What is the default username and password for sample packages mentioned in this article for all the sample packaged applications?
http://www.oracle.com/technology/products/database/application_express/packaged_apps/packaged_apps.html#PACKAGED
Regards
Edited by: user20090209 on May 19, 2010 1:37 PMHi,
Try same user name and password as you login to your workspace.
Most of applications use Application Express authentication
Br,Jari
Edited by: jarola on May 19, 2010 9:06 AM
And when you have downloaded and installed application to your workspace, you can always change authentication -
Changing WPA Username and Password
Hi Guys,
I am quite new to Wireless. would appriciate any help on this issue.
I am using a 891w as autonomous AP. I got some basic config from support forum.. Once configuration was done, i could see the SSID; but it was asking for username which i could not figure out. Here is the config below.
hostname ap
no aaa new-model
dot11 syslog
dot11 ssid WirelessNetwork
vlan 1
authentication open
authentication key-management wpa
guest-mode
mbssid guest-mode
wpa-psk ascii 7 cisco
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm
encryption mode ciphers aes-ccm
broadcast-key vlan 1 change 30
ssid WirelessNetwork
antenna gain 0
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm
encryption mode ciphers aes-ccm
broadcast-key vlan 1 change 30
ssid Wirelessnetwork
antenna gain 0
dfs band 3 block
channel dfs
station-role root
interface Dot11Radio1.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
no ip route-cache
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
cns dhcp
end
Please help me change the username and password for the SSID.
I hope in the able example the password is cisco.
Thanks you.Hi,
This should be asking you only the password not the username as you have confired with wpa-psk. What client device are you testing this with? If this is wondows machine please choose your sececurity as WPA-Personal on the wireless profile and then it would asked for the Security Key..You will have to enter your password there. The password from the configuration i can see it as cisco.
wpa-psk ascii 7 cisco
Hope thats helos,
Regards
Najaf
Please rate when applicable or helpful !!!
Maybe you are looking for
-
Can I use the Command Line Interface on Unix?
Hi, We use 9iAS on Unix. We want to use Discoverer Command Line Interface on unix to export the worksheet query result. Can anyone know how to do this? I couldn't find out the command similar to dis5usr.exe for windows version. Thanks. Richard Qiu
-
Problems of setting values% with 2 decimal places in any graphics. What sho
Guys, I have the xcelsius 2008 and can not make it work chart with values % and 2 decimal places. Already set up everything that I know the spreadsheet and graphics. Someone knows what can I do? Thanks Anderson - Sao Paulo - Brazil.
-
GarageBand does not open, but it's a bit bouncy....
Here's the dilemna: I need to create some stuff for my teacher for our Yearbook/Yeardisc, and I was going to use GarageBand to do this with. (Already know how, just hoping this will provide some incentive to help some random loser in another state as
-
Live Auction bids not copied to EBP at end of auction
Dear All, We are working in SRM 5.0 with LAC 2.0. We are on support pack 8. The problem we are facing is: Bids are created via the Live Auction applet but after the auction ended, the bids cannot be seen on the EBP system. We also tried sap note 8111
-
Oracle Openscript and javascript functions
I'm using Openscript on a form page that is using a clickable div "save" button. When the button is clicked manually a javascript event is executed to save the changes on the page. When I play back the script, the script clicks on the button and gets