Change IP address for airport

I ahve an isue with a website that I can get on when there is a direct connection from the modem but when I go through the wireless network it will not connect. Everything else works, so I assume it is the IP address from the airport/router. Or am overlooking something else?  Merry Christmas!

Merry Christmas as well!
You are on the right track.
It may be a bit hard to understand, but the website that you cannot reach has likely blacklisted your IP address or more likely, MAC Address from your Apple router.....probably because their server thought by mistake that you were spamming them.
Get with the technical support folks at the website and explain what is happening. They will ask you for your IP address or MAC Address of the Apple router so that it can be removed from their blacklist and then you will be able to access the site again from your Apple network.

Similar Messages

  • How do I get a valid IP address for airport express?

    I am trying to set up my airport express.  All the steps work fine except for when I get to the end it says I need a valid IP address for airport.  Any help would be appreciated.

    I'm not sure what you're trying to set up here? Are you trying to set up the AX to provide wireless access to the internet, or to extend an existing network?????

  • Steps to change IP address for SAP B1 server

    Dear Guru
    My company is going to change the IP address of SAP B1 server, because I am very new in this area, so pls clarify for me the following doubt
    1. May I change the IP address with the SAP B1 is running?
    2. If I need to stop the B1 services, how can I stop it? Stop at windows service level? or is there any console for me to stop the service like SAP R3?
    3. Do I need to stop the MSSQL service as well?
    4. Do I need to reboot the server before I startup the SAP B1 service?
    Regards
    Guodong

    Dear Guodong,
    Just assuming you have only one question since that is the forum rule.
    To change IP address for SAP B1 server, you need to Stop and restart the server to prevent the potential problem.  B1 is not the same as R/3, you have to stop all B1 related services.
    Thanks,
    Gordon

  • Change of address for existing Plant -

    Hello,
    The requirement is to change the address for an existing Plant. Is this opkay to do - does this impact any other MM/Production processess.
    Thanks,
    RT

    Hi,
    Change in address will not impact on anything except the TAXES
    In address detail country,region and tax jurisdiction is maintained and this fields area in use for calculation of tax then it will impact.
    If region and tax jurisdictions is not in use for tax calculation then you can change.
    kapil

  • Can anyone help me with changing email address for resetting password notification

    Can anyone help me with changing email address for resetting password notification?

    If you know the answers to your security questions, you can change your rescue email address as shown in step 6 in this article: http://support.apple.com/kb/HT5312.
    If you don't kow the answers to your security questions or need other assistance doing this, either contact Apple for assistance by going to https://expresslane.apple.com, then click More Products and Services>Apple ID>Other Apple ID Topics>Lost or forgotten Apple ID password, or contact the Apple account security team: http://support.apple.com/kb/HT5699.

  • Change IP address for WLC

    I want to change IP address for WLC in production, should I convert Access Point from LWAP to IOS then convert again to LWAP ?
    Regards,

    Hi Friend,
    The best way is configure your controlelr as primary controller for all APs. You can do so going to wireless tab and then click on each AP detail and configure this controller as primary controller.
    Also if you have WCS you can do the same in one go for all APs and after that even if controller ip address is changed they will stay join to this controller.
    HTH
    Ankur
    *Pls rate all helpfull post

  • Old email is closed.  I have no access to it.  Cannot change email address for icloud in system preferences,does anyone have a way this can be corrected?  I don't have access to icloud.

    Old email is closed.  I have no access to it.  Cannot change email address for icloud in system preferences,does anyone have a way this can be corrected?  I don't have access to icloud.

    Hi Joycars,
    Can you not simply sign out of the iCloud account with the incorrect email? Not sure I'm following?
    GB

  • Change company address for report: PC00_M40_PTX - Form 5

    Dear Experts,
    I want to change company address for report PC00_M40_PTX - Form 5. Can you please help me?
    Note: Personnel area address already maintain
    Thanks and regards,
    Mayur
    Edited by: Mayur114 on Jul 20, 2011 3:04 PM

    Hi,
    I checked the program, in which Include - PCPTXIN6_PDF line no 57 is used for checking the address & displaying in the output.
    In that CONCATENATE sadr-name1 sadr-name2 is used for the Empr address part. Check in ur case Name2 is having any entry or not.
    The name1 & name2 is 35 character length and it can be maintained in V_T001. Select the Company code & SHIFT+F5, both the fields are on top of the Name header. You can mention the details there & do a test run to check by using both the Function modules.
    Regards,
    Prasad lad

  • I need to change the MAC Address for Airport on MacBook

    I have a specific need to change my son's Airport MAC address as his school requires the use of USB network cards that aren't compatible with MACs. These cards are needed because the school's router uses MAC address filtering.
    Before we upgraded his Mac to Snow Leopard, we were able to change the MAC address to the MAC address of the useless dongal the school supplied. We basically created an AppleScript program that ran the "sudo ifconfig en1 ether xx:xx:xx:xx:xx:xx" and all was good.
    This command no longer works for changing the MAC address. We tried it as root user as well and by typing it into the terminal window as root. After running the command, we can run "ifconfig en1" and it does display the new mac address but when we turn the airport on and try to connect, it just hangs and won't connect.
    Our other non-Snow Leopard still works fine after running the commands so I'm guessing Apple disabled this functionality. It's hardly a security issue by being able to change your mac addres.
    Is there a new way to accomplish this? I've searched everywhere.
    Thanks!

    Would an easier solution be to provide the school's IT admin with your mac address and have it added? If they can add a block of mac addresses for the usb dongles, they can add more for machines that cannot use the dongle.
    Also: "It's hardly a security issue by being able to change your mac address."
    While it may not be a security issue for your machine, it is a security for the school network who is using mac address filtering as hopefully only one part of their wireless security.
    That being said, have you read this?
    http://osxdaily.com/2008/01/17/how-to-spoof-your-mac-address-in-mac-os-x/

  • Airport utility 6.1 change ip address for router

    Hi there,
    I want to change the IP address for the router from 192.... to 10.....?  It doesn't seem possible with the new version of the aiport utility.
    Any help would be greatly appreciated.

    You can change the IP address range that the AirPort Extreme provides as follows:
    Open Macintosh HD > Applications > Utilities > AirPort Utility
    Click directly on the AirPort Exteme icon
    Click Edit in the next small window that appears
    Click Network at the top of the next window
    Click Network Options at the bottom of the window
    Here, you can changet the iPv4 IP address range from 192.168.x.x to 10.0.x.x
    Click Save and then click Update to restart the AirPort Extreme
    IF....the Network Options button is grayed out, this indicates that the AirPort Extreme is in Bridge Mode. In that type of setup, you have another modem/router or gateway "upstream" on your network.  That is is the device that is providing the 192.168.x.x. IP addresses.
    The AirPort Exteme simply passes through that network information to connected devices in Bridge Mode, since you only want one router on the network providing IP addresses.
    You will need to check with the support folks for your modem/router or gateway if you want to modify the settings on that device.

  • Change MAC Address On AirPort Extreme

    I'm using the latest Apple AirPort Extreme 802.11n (Apple Part Number MB763AM/A and Model A1301 as noted on the box). I am currently using Firmware 7.5.1. I haven't yet updated to the latest AirPort Base Station Firmware 7.5.2.
    Is there a way to change the MAC Address on this device? The reason I ask is because I use cable Internet and releasing and renewing the IP Address on cable never works. You're basically stuck with the same IP address for months on end unless you leave your connection off for at least 72 hours or more (DSL out here works differently - you get a new IP Address immediately after releasing and renewing).
    I don't like using the term "spoofing" as it sounds as if you're trying to do something devious (which I'm not) but I just don't like having the same IP Address for months on end since I don't think it's wise for security reasons.
    I'd be interested in knowing if there is a way to change the MAC Address of my AirPort Extreme, perhaps using a third-party utility of some sort, perhaps through the Terminal or maybe the new firmware update allows you to finally do this?

    Is there a way to change the MAC Address on this device?
    If you are referring to the MAC address of the AirtPort Extreme, it is not possible to change this.
    You're basically stuck with the same IP address for months on end unless you leave your connection off for at least 72 hours or more (DSL out here works differently - you get a new IP Address immediately after releasing and renewing).
    The IP address you are referring to here is assigned by your service provider. The AirPort Extreme has no control over this.
    I'd be interested in knowing if there is a way to change the MAC Address of my AirPort Extreme, perhaps using a third-party utility of some sort, perhaps through the Terminal or maybe the new firmware update allows you to finally do this?
    Sorry, not possible.

  • Changing the Address for Shipto party for a Service Order..... pls respond

    Hi friends,
    When i create a Service Order, using CRM_ORDER_MAINTAIN, I want to pass Ship to party number and its address.(its not Master data from BUT000, ADRC tables.).
    THe address data what i mean is when we go to Partners tab, the address you see is not master data.
    I want to update this address.
    Somehow i was able to create with my Shipto party , but im not able to give the address in the IT_PARTNER parameter of Crm_order_maintain.
    How can i give the address aswell, when i create Service order, or even changing a service order.
    Basically i want to change the address of ship to for a SO.
    kindly respond....
    thanks in advance,
    Niraja

    THis is the code i wrote to update the street: . but its not updating.. :((((((((((
    pls hlp fnds...
        CLEAR: ls_input_fields.
        ls_input_fields-objectname  = 'PARTNER'.
        ls_input_fields-ref_kind    = c_a.
        IF p_header-guid IS INITIAL.              
          ls_input_fields-ref_handle = c_handle.
          ls_sconf_partner-ref_handle = c_handle.
        ELSE.
          ls_input_fields-ref_guid = p_header-guid.
          ls_sconf_partner-ref_guid   = p_header-guid.
        ENDIF.
        ls_partfieldnames-fieldname =  'ADDR_NP'.
        INSERT ls_partfieldnames INTO TABLE lt_partfieldnames.
        ls_partfieldnames-fieldname = 'ADDR_NR'.
        INSERT ls_partfieldnames INTO TABLE lt_partfieldnames.
        ls_partfieldnames-fieldname = 'ADDR_ORIGIN'.
        INSERT ls_partfieldnames INTO TABLE lt_partfieldnames.
        ls_partfieldnames-fieldname = 'ADDR_TYPE'.
        INSERT ls_partfieldnames INTO TABLE lt_partfieldnames.
        ls_partfieldnames-fieldname = 'STD_BP_ADDRESS'.
        INSERT ls_partfieldnames INTO TABLE lt_partfieldnames.
        ls_partfieldnames-fieldname = 'KIND_OF_ENTRY'.
        INSERT ls_partfieldnames INTO TABLE lt_partfieldnames.
        ls_partfieldnames-fieldname = 'STREET'.
        INSERT ls_partfieldnames INTO TABLE lt_partfieldnames.
        ls_input_fields-field_names = lt_partfieldnames.
        CONCATENATE '000000000055 ' p_header-shipto_no '        BPBP'
               INTO  ls_input_fields-logical_key.
        INSERT ls_input_fields INTO TABLE lt_input_fields.
        ls_sconf_partner-ref_partner_handle = '0001'.
        ls_sconf_partner-ref_kind = c_a.
        ls_sconf_partner-ref_partner_fct = c_00000055.
        ls_sconf_partner-ref_partner_no  =  p_header-shipto_no. "'0010017295'.  "
        ls_sconf_partner-ref_no_type = 'BP'.
        ls_sconf_partner-ref_display_type = 'BP'.
        ls_sconf_partner-kind_of_entry = 'C'.
        ls_sconf_partner-partner_fct = c_00000055.
        ls_sconf_partner-partner_no  =  p_header-shipto_no. "'0010017295'.  "
        ls_sconf_partner-no_type = 'BP'.
        ls_sconf_partner-display_type = 'BP'.
        ls_sconf_partner-mainpartner = 'X'.
        ls_sconf_partner-addr_nr = '0000060435'.
        ls_sconf_partner-addr_np = ''.
        ls_sconf_partner-addr_type = 1.
        ls_sconf_partner-addr_origin = 'B'.
        ls_sconf_partner-relation_partner = '48222495E5735887E1000000CC9AA02A'.
        ls_sconf_partner-std_bp_address = ''.
        ls_sconf_partner-street = 'helloteststreet'.
        INSERT ls_sconf_partner INTO TABLE lt_sconf_partner.
    Can somebody give me any hints. pls ......
    thanks in advance,
    Niraja

  • Changing email address for Preferences???

    Hi Everyone,
    This question actually has nothing to do with SQL! I am having trouble working out how to change were my email alerts are being sent to! I login with my hotmail account, but email alerts (concerning my threads) are being sent to my work address. I can't
    work out how to change were alerts are sent to...such a seemingly simple thing! However the MSDN site isn't the easiest to set preferences in!!!
    Primarily I use the MSDN site for learning about SQL so I am specifically interested in changing where alerts related to the following URL -http://social.msdn.microsoft.com/Forums/sqlserver/en-US/ are sent to...
    Of course I have Googled this, but with NO LUCK (admittedly I didn't get super desperate and Bing Search!).
    Any help here will be greatly appreciated. If your an Administrator with enough skill to move this thread can you please share instructions on how to change the notifications email address???
    Kind Regards,
    David

    Hi David,
    You can change the email address notifications are sent to via 'My settings'. To get there, click on the 'Quick access' dropdown in the upper left (under the 'Ask a question' button) and then click on 'My settings'.
    There's a 'Configure alerts' section there where you can change the address.
    Just as a heads up (you don't have to worry about this, but I'll post this for future people who find this thread), making any changes in 'My settings' mangles all HTML tags in your signature block. You'd need to paste in fresh HTML before saving the changes
    to ensure that your signature doesn't break.
    EDIT:
    I just learned that you'll also need to confirm the new address that you enter into the 'Configure alerts' section before notifications will start being delivered to this new address. The confirmation email may take quite a while to appear.
    Don't retire TechNet! -
    (Don't give up yet - 13,085+ strong and growing)

  • Changing Email address for BTWiFi-with-FON

    Is it possible to change the username/email address for logging in to BTWiFi-with-FON as the btinternet.com email address I got lumbered with is very long (29 characters) and awkward to key in on a smartphone?
    Solved!
    Go to Solution.

    A1944 wrote:
    pottyperson wrote:
    Keep the phone's Wifi switched off until you actively want to use it. That will probably save on battery usage as well.
    Thanks for the idea, but unfortunately that would not help as I use it on the WiFi at home quite a lot, especially when I have the PC switched off.
    Sorry, I got the wrong end of the stick. You need to set the phone to prioritise wifi connections, but I don't know the procedure for iPhone as I have Android. You could try simply deleting BT WiFi from the list of connections to see if it gets a lower priority next time you connect to it.  
    You can click the white star next to this message if you think it was helpful.

  • Change Invoicing address for number of PO's

    Hi
    We have a requirement to change the invoicing address for all PO's existing in the system.
    How can we achieve it? 
    Please help.

    Hi, 
    There is no invoicing party mentioned in PO header.
    Company procures raw material from one comapny code to another c.code.
    c.code is coming as delivery address not invoicing address.
    The invoicing address mentioned is of Customer.
    There is the requirement that invoicing address has been changed and all po that were subjected to send to previous address need to get updated with new invoicing address.
    I know that address is getting updated from adrnr field in adrc table but dont know how to change for mass po's.
    Please help.

Maybe you are looking for