Change language for router setup page

Hello Lynksys im using older model and havent gotten around to buying a new wireless router, i was wondering is i do decide to get a newer model will my site be in english. currently i have the site in german and it will not for the love of my life translate to english?( i am in United States should my site be in german when i put in the default IP address?) Could this have been a problem in installment?

Hi! There are actually two ways on how to change the language for your router. It's either thru the setup cd or going thru the link where you can change it. If you're going to use the cd, you will have to run it again and you should be presented with an option to change the language. If you don't have it anymore, you may just go to http://192.168.1.1/language.htm, it should let you change the language. Found that on this link: http://homecommunity.cisco.com/t5/Wireless-Routers/Change-Language-Pack/td-p/3119.

Similar Messages

Can't connect to router setup page

Hi,
I have a WRT54G wireless router, version 2.1. It's been working fine for the last 3 years and suddenly the WLAN light is out and there's no communication between router & computer. I've tried resetting it (via reset button, and unplugging power) a million times with no results. A techie thought maybe I needed a firmware upgrade -- which I've downloaded, but now I still have to access the setup page to install it, which seems to be impossible. The 192.168.1.1 page won't come up at all. (And when I went into the command prompt, it said my Default Gateway was 207.237.223.1 -- which, of course, I've tried, but that won't come up either.) I've turned off firewalls and antivirus programs, thinking they might be the problem -- still nothing. Any suggestions/advice would be MUCH appreciated! Thanks in advance!
TrevorNYC

You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.

WRT54GS router setup page won't display most text

So I bought a new Linksys WRT54GS v6 wireless router yesterday, and I was able to set it up to share my DSL line, but when I went to the router setup page (192.168.1.1), it wouldn't display most text. It displays text in the entry boxes, but there are no links or other text on the page. I took a screenshot which can be seen here: http://img87.imageshack.us/img87/3390/routersetuppagemc1.jpg
Does anyone know what I can do to solve this issue?

Hey Merugo. I was having the same problem with the router settings screen refusing to load for my WRT54G. Do you happen to have v.5 of the router? After digging around in the help files on the site, I found this for firmware recovery for the WRT54G v.5 and it fixed the problem I was having once it loaded the updated .bin. Blank screen be gone.
http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=3176
(The first time the router tried to load the new .bin it timed out. And the second time it installed correctly though it didn't display "Upgrade Success" like it's apparently supposed to.)
Hope this can maybe help you since it fixed things for me.Message Edited by Res on 10-03-200606:44 PM

Can't log into router setup page

I updated my firmware today on a WRT54GL router. Upgrade was successful but when I clicked to continue I got a message that access was denied. I have tried to log in with the address 192.168.1.1 and get the same message. Any help?

After a firmware upgrade, you must reset the router to factory defaults (see note below), then setup the router again from scratch. If you saved a router configuration file, DO NOT use it. If you have not done this since the last firmware upgrade, please do it now and see if that corrects your problem.
If you still have trouble viewing your router setup pages, do the following:
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall.
If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Check to see if your "modem-router" is using the same 192.168.1.x address space as your Linksys router. If it is, then report back with this problem, and also state the make and model of your modem-router.
If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
If you still have problems, then you need to download and install (or re-install) the latest firmware for your router. After the firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.
Note: To reset the router to factory defaults: Power down the router and disconnect all wires from it. Wait one minute. Power up the router, allow it to fully boot (1-2 minutes), then press and hold the reset button for 30 seconds, then release the button and allow the router to reset and reboot ( 2-3 minutes). Power down router. Wait one minute. Connect one computer, by wire, to a LAN port on the router. Boot up system. It should work.
Message Edited by toomanydonuts on 01-06-2008 08:04 PM

Changing language for a particular user

Hi
How to change language for a particular user in backend system ?
Actually i have to get logon language en but automatically it is coming "DE". That is the reason even single sign-on is not wrking from portal for particular user all other users are getting "EN" by default.
Please give the solution for this issue.
it is very urgent.
Thanks and Regards,
Phanikumar.

You can set the logon language in System>user priofile>own data

Shame to remove Get Info option to change language for individual application!

Its a shame for Apple to remove the Get Info panel option to change language for individual application! For these days I used Leopard, where I had this option, now I bought a brand new mac, for a bunch of money, with Lion, and this option had disappeared. What's that? Apple is working on making more complicated the life of their users?

Thanks for your tip, but languageswitcher not set the language permanently just for the applications started from that application. Very inelegant and windows like way.
I used the terminal to set the defaults for individual application, but that is step back to the age of command line.
I spent with this problem 1 hour instead of 1 minutes. Big step back.

Cannot install Software for E2500 or access router setup page

Please help! I first bought the e1200 version and when I tried to download it on my computer, it worked at first and installed correctly, but the cisco connect didn't properly install. I was able to log into the router online setup page ONE time. I tried to reset it and reinstall but it will not work.
So I thought ok let me go and purchase a better one (thinking it was the router version having issues). So I brought it back and purchased the E2500 and I am having the same trouble.
I have tried to reset it about 20 times and reinstall and it will not install at all. It still gives me internet, but I cannot log into the http://192.168.1.1/ page at all, it tells me internet cannot display...
Please help!

Hi there. Please check first if router is responding properly. Are you on Mac or Windows? On Windows pc, open command prompt (start>run>cmd for XP/ start>search>cmd for Vista and Windows 7) and type ping 192.168.1.1 and press enter. If you are getting 4 lines of replies from 192.168.1.1 bytes 32 something then router is okay. On command prompt again go down to the next line where it has the flashing cursor and type this time: start http://192.168.1.1. After you press enter, your browser comes up and normally will prompt you to log-in to area 192.168.1.1 and that is where you can use admin in both fields (username and password since you reset the router already). If you get page cannot be displayed still, disable proxies on the browser. Example if you are on IE, you click tools and then internet options and go to connections and click lan settings. On the small window that comes up, just make sure nothing is checked and then try on the address bar again http://192.168.1.1. If your computer still cannot access it, try a different browser or a different computer.

Pages 5. change languages for different paragraphs?

In Pages '09 I could change the spell check language for different paragraphs by going to the Inspector, then "text" then "more." That appears to be gone now. Does anyone know how to do it?

Thanks Rene! That got me thinking that I didn't test spell check with a new document (where I hadn't set the languages before). It looks like Pages 5 detects the language automatically and changes the spell-checker. Check this out:
I pasted the first three paragraphs from wikipedia articles and then mispelled one word in each paragraph. Pages found the misspelled words but did not underline the rest.
Then in the last two paragraphs (which I typed), you can see that "gli" was NOT underlined in the Italian sentence but WAS underlined in the English one. I guess this explains why there's no setting for it. It is automatic now.

Change default language for the logon Page

Hello,
On a SAP Portal 7.0 SP 17 I've a problem with the language of the Logon Page: is always in English.
If I go to internet explorer -> tools -> internet options -> languages I've set Franch as language.
When I open the Logon Page (http://xxxx:50100/irj/portal) all the text are in Englisg: Welcome, User ID, Password, Log On. While the iViews and Pages are in Franch.
Does anyone tell me how can set my Logon Page in French without edit PAR file?
Many thanks in advance
A.

Hi !
I'm facing the same problem !
What do you mean by "And the language set for the Guest user in the UME?"
Where can I modify this option?
Many thanks
Mike !

Change language for the Caller ID announcement

How can I change the Caller ID announcement from English to say German ?
I have installed the German text to speech package and that works as expected for messages text to speech so one would think that can be used for the Caller ID announcement as well.
Any thoughts, help ?
Cheers
chris

Hi MC
In the OP43 transaction (Setup group category-setup group Key SPRo ), select the setup group key for which you want the translation to be maintained, select the GOTO in the menu bar - click on the translation and select the Language for which you want to maintain the translation. Maintain your translated text here.
The other way is to Log in in the language you want to maintain the transaltion Go to OP43 and maintain the details.
You will have to maintain them in SPRO and the same will be reflected for the recipes in the respective login language in the master recipe.
If the solution works for you or is helpful, give suitable points.
Regards,
Amol Kale
Edited by: Amol Kale on Mar 1, 2012 7:09 AM

Unable to enter router setup page

my router is WRT54G..i can only enter into the setup page once..after i close my IE..i am unable to enter anymore..must do a reset to enter again..is my router faulty ? plsssss help

well.....possibly a firmware issue...follow the steps :
1)go to ftp.linksys.com/pub/network and download the tftp.exe file....
2)go to www.linksys.com/download and download the latest firmware for the corresponding version no. of WRT54G ...
3)run the tftp.exe file
4)here, the server is router's ip add ( 192.168.1.1 ) , password is router's password ( by default it's "admin" ) and browse the firmware file and click upgrade
5)once the firmware is upgraded , reset the router and reconfigure it....

Unable to change language for SAP BW Report Iview

Dear all
We are currently rolling out BW Web Templates can be displayed in both EN and MS languages. The language can be changed via the URL that we display, e.g.
For English Language:
http://<hostname>:<port>/sap/bw/BEx?SAP-LANGUAGE=EN&cmd=ldoc&template_id=ZTEST
For Malay Language :
http://<hostname>:<port>/sap/bw/BEx?SAP-LANGUAGE=7&cmd=ldoc&template_id=ZTEST
We have published these templates into Ent. Portal 6 using SAP BW Report Iview, but unfortunately we cannot view the report in the Malay language (SAP-LANGUAGE=7), even though we have inserted the command SAP-LANGUAGE=7 in the SAP BW Report Iview query string. All the reports, although defaulted to SAP-LANGUAGE=7 displays in English. We also tried to set the language settings for the Iview, but there are no language 7 or MS in the Iview. It can only be defaulted to the Portals language, which is English.
Note that the reports can be viewed in the different languages if we using the URL separately outside of Portal, and also within BW Bex Analyzer itself. Only the Portal doesnt allow us to view the reports in MS language.
Can someone help us on this matter? All helps really appreciated. Thanks a lot.

Hi Chris,
That's a bit odd indeed. If I understand your question correctly, you do get the BW reports in the correct language (either English or Malay) using the url's in your post but not when using them within a standard BW report iView?
The language setting for the iView has, unfortunately, nothing to do with the language for the content itself but can you tell me what the requested URL is for both Reports?
The BW Report iView is based on the Application Integration Component that generates the URL based on the paramaters you provide in the BW report iView.The following template is being used: <iView[PORTAl_URL]>?System=<System[url_Encode]>&Report=<Report>&DynamicParameter=<DynamicParameter[url_Encode]>. I could be that the generation of the URL fails due to the 7 (don't know why, just a gut feeling because it's the only thing that's different between those urls). You could try to use create an iView based on the Application Integrator instead (some more control over the URL template) but first you need to check whether the URL generated by the iView is correct.
Cheers!
Frodo
P.S: Award points if you find this useful

Acrobat Reader 11 MUI : Impossible to change Language for Final user.

Hello,
I need to deploy AdbeReader on several PC.
On my enterprise, we have several language (english, french, deutch...)
I have configure MSI package with Adbe Customization Wizard. But on this tool we cannot choose "Set the language to the OS language..." By defaut, I choose English.
I have read on Adobe Reader document that by default, for MUI, we need to put 1 to this reg key :
HKLM\SOFTWARE\Adobe\(product)\(version)\Language\UseMUI\
In my case, it's ok.
But, when I install Adobe Reader with my mst file, application stay in english (even if I use a french computer).
And, if I try to change manually the language it does'nt works. Choose at application startup does'nt too. I have never the popup to choose the language.
Someone can help me ?
Many thanks !

Adobe Properties — Enterprise Administration Guide
Language 11 & later SUPPRESSLANGSELECTION MUI installers only. The default of 1 does the following:
Sets the language to the OS language for all users.
Disables the language selection dialog on application startup for any user.
Sets HKLM\SOFTWARE\Adobe\(product)\(version)\Language\UseMUI\bUserMUI to 1
This is particularly useful for multiuser installations where the language selection dialog would normally appear if a different user logs in, Citrix installations, and so on.
A value of 0 results in the language selection dialog appearing at first launch for every newly logged in user of the machine. For Acrobat this property is not applicable. When Acrobat is installed with MUL serial number and LANG_LIST=ALL, the launch language would be the same as OS language unless a language transform is also applied.

Change Language for Spell Checking in Mail

Hi,
as far as I could see from other articles here and on other sites, there is no easy way to change the language for spell checking in Mail. It's difficult to imagine that this is true, as in this global world switching from one to another language in different mails is (at least for non-US/UK/etc. users) an immanent need.
Thanks for letting me know if I am mistaken.

Tom Gewecke wrote:
there is no easy way to change the language for spell checking in Mail.
If what you are asking about is some kind of shortcut to avoid using the Edit menu, you are correct that nothing like that exists for Mail (or other Apple apps). I think if you use something like SpellCatcher you can switch via a single keystroke.
The fastest method I know of is through AppleScript. I personally use "quick and dirty" routines for shifting from French to English and vice versa, both in Mail and Safari. Your typical toggle-switch bare-bones app looks like this:
tell application "Mail"
tell application "System Events"
tell application process "Mail"
set frontmost to true
try
click menu item "Show Spelling and Grammar" of menu "Spelling and Grammar" of menu item "Spelling and Grammar" of menu "Edit" of menu bar 1
set fen to window "Spelling and Grammar"
click pop up button 1 of fen
set lemenu to menu 1 of pop up button 1 of fen
if selected of menu item "Français" of lemenu is true then
click menu item "British English" of lemenu
else
click menu item "Français" of lemenu
end if
click button 1 of fen
on error
beep 2
end try
end tell
end tell
end tell
Nothing fancy here! Compile it, keep it handy (in the dock for example), and a single click does the switch for you. You can make endless variations on this, even make it look kind of smart, with dialogs and all that, thus defeating the purpose.
AppleScript support is kind of sketchy so you have to use UI programming.
Cheers,
RTP

How change language to Spanish in Pages 09

I need to change language frecuently in pages, key note and works. But I haven´t found the way.
Help is welcome

You select the text you want to be Spanish or French and make it the language you want in the Text Inspector.
It is then part of the Text style. If you want you can make a Paragraph Style which has the language as part of it in the Styles Drawer.
Peter

Change language for router setup page

Similar Messages

Maybe you are looking for