Change pointers are not generated when creating a material master

Dear Experts,
Change pointers are not generated when creating a material master.
However, when a change is made to the already created material, the change pointers are created according the fields in BD52.
Am I missing any settings?
I need to create change pointers immediately when I create the material master in MM01.
Please suggest.
Regards,
Shetty

did you follow the steps given in
http://help.sap.com/saphelp_nw73/helpdata/en/4a/6dcbe9c95261a3e10000000a421937/frameset.htm

Similar Messages

Change Pointers are not getting populated in BDCPV table.

Hi All,
         I am trying to create IDOC for Activity type master - KL02 through change pointers. For that I have done following things.
Message type - COAMAS
1. Created Custom message type - WE81 - ZIN_COAMAS_TCSMOBILE
2. WE82 - Config for Mess Type and Idoc type combination
3. SCDO - Checked object type LSTAR and have required tables in that object.
4. BD61 - Activated Change pointers - Generally.
5. BD50 - Checked Active for ZIN_COAMAS_TCSMOBILE
6. BD52 - Added fields for I want to create Change pointers
7. BD60 - Message type and ref Mesage Type and function module config.
8. BD64 - Created distribution model for my Message type
After doing all this settings the change pointers are not getting created in BDCP and BDCPV tables.
Note - The entries are going in CDHDR and CDPOS table for activity which i change through KL02 for class LSTAR
Can anybody figure out what need to be done in this case?
Regards,
Gautam Joshi.

Hi All,
          Solved the problem myself.
          In BD52 I have given
          LSTAR               CSLA         KOARS
          LSTAR               CSLA         LSTAR
          LSTAR               CSLT          KTEXT
          Here the data of activity are stored in TCLA and TCLT tables. So intially while doing config in BD52 I have given TCLA and TCLT table names.
          But I debugged the KL02 and found that change pointers are not created for TCLA and TCLT table. further looking into CDHDr and CDPOS table I found that for COAMAS message type in these two tables table name was CSLAB.
CDPOS entry
LSTAR
3166442
119512890
*CSLAB*
2003166442   2400123120000101
KTEXT
U
--> BUT CSLAB is structure.
After putting these entry in BD52 the problem solved.
LSTAR     CSLAB     KOKRS
LSTAR     CSLAB     KTEXT
LSTAR     CSLAB     LSTAR
Regards,
Gautam Joshi.

0CML_DELTA : Change pointers are not active

Hi All,
I have successfully did the delta init without data transfer for datasource 0CML_DELTA and 0CML_DELTA_CAP. Now, While trying to load delta, I am getting an error "Change pointers are not active" for both the datasource 0CML_DELTA and 0CML_DELTA_CAP.
The position datasources are fecthing 0 records.
I have activated the change pointers in BD61, even though I am getting the same error.
Anyone faced the similar issue or have any clue about the problem.
Thanks in advance,
Pravender
Edited by: Pravender on Sep 30, 2010 11:09 AM

I resolved it. I was activating change pointers in BD61. But fot CML we need to activate in SPRO--> SAP Banking --> Loans Management --> Basic settings --> Installation parameters ---> Define general installation parameters.
Then it will work.
Pravender

Deletion change pointers are not going to ECC after C5

Hi,
My issue is that I am running C5 after Planning run.But deletion change pointers are not going to ECC.Because of this we have duplicate of orders in ECC.We are running CCR to bring back the "Planned orders with deletion change pointers and deleting again using RRP4.Why deletion change pointers are not going along with creation change pointer?Help will be highly appreciated.
Thanks&Regards
Venkadesh

Hi,
Check whether you have enabled the " delete events" check box. This check box will be valid if you are publishing the planning results thru background job.
If you set this indicator, the system deletes all selected change pointers without sending them first.
Thanks,
nandha

Partner Role not coming when creating the Vendor Master

Hi all
There is a standrd role AZ.
There is a standrd Partner Determination procedure L1.
The role AZ is assigned to the Partner Determination procedure L1.
When creating the vendor master in MK01 the role is not coming in the list of partner function.
For Document types there is a standard shema 0002.
The role AZ has also been assigned to doc type.
What can be the reason.
Is the assignment against doc type at all required.
Please suggest.
Regards

The procedure for setting partner functions:
Step 1
Vendor Account Group
IMG->LOGISTICS GENERAL->BUSINESS PARTNER->VENDOR->CONTROL ->DEFINE
ACCOUNT GROUPS AND FIELD SELECTION
Step 2
Defining Partner Schemas
IMG->MATERIALS MANAGEMENT->PURCHASING->PARTNER -> DETERMINATION -
>PARNER SETTINGS IN VENDOR MASTER RECORD
->DEFINE PARTNER SCHEMAS
Step 3
Assign Partner Schema
IMG->MATERIAL MANAGEMENT->PURCHASING->PARTNER DETERMINATION->PARTNER
SETTINGS IN VENDOR MASTER RECORD->DEFINE PARTNER SCHEMA
« THEN ASSIGN PARTNER SCHEMA
Step 4
Define Permissible Partner Role Per Account Group
IMG->MATERIAL MANAGEMENT->PURCHASING->PARTNER DETERMINATION -
>PARTNER ROLES ->DEFINE PERMISSION PARTNER ROLES
If you want a partner schema for your own document type then define your partner schema and assign to document type using the below mentioned path.
IMG->MATERIAL MANAGEMENT->PURCHASING->PARTNER ->DETERMINATION -
>PARTNER SETTINGS IN PURCHASING DOCUMENTS ->DEFINE PERMISSION
PARTNER SCHEMAS
And then
ASSIGN PARTNER SCHEMAS TO DOCUMENT TYPE
Once you have this configuration then you change your vendor in easy access menu (XK02-select partner function) define the partner roles.

Books are not saved when created with iPhoto 09

When creating a book, everything is normal but the book is not saved in the computer. So I have to finish the project and order It. The name of the book is still listed on the left but there's no photos or text. I also have a book that seems corrupted because when i try to open the file iphoto jams and i'm not able to remove the corrupted book because the file can't be opened.
Please help me

Welcome to the Apple Discussions. Sounds like a damaged database file. Launch iPhoto with the Command+Option keys depressed and follow the instructions to rebuild the library. Select the last three options.
Click to view full size
Also what system and iPhoto versions are you running?
Happy New Year

Spool not generated when creating the TO from TR

Hello,
I am facing a issue while creating Transfer order. My scenario is like below:
1) Create Goods issue MB1A with two items
2) Create Transfer order from Material document
3) TO is created with 2 items
4) But spool is generated only for one item.
As per my analysis, the TO line item with storage unit which starts with 3* gives a spool while the second item with storage unit which starts 9* does not generate a spool.
But when I print the TO manually in LT31, I am able to see the spool for both items.
Please help me if you have any idea.
Thanks & Regards,
Sainath

Hello,
Please see the attached spool output when TO is printed manually LT31.
However, when the TO is printed automatically, one spool will be displayed in SP02.
Please let me know if you need any more clarifications.
Thanks,
Sainath

SID is not generated when i load the master data

hi
We got the error "No Sid found "000631330" of characteristic 0COSTELMNT when transaction data is loaded.
We have loaded the value "000631330" for characteristic 0COSTELMNT and reloaded from the PSA . still we r getting the error No Sid found "000631330" of characteristic 0COSTELMNT
Thanks much in advance
Raj

Hi.....
First check whether that value exist in the Master data table.........to do this Go to RSA1 >> search the infoobject >> Go to the Master data / text tab..............here check the P table...........to check it double click on the table..........there check if that value exist...........and also check the version..........whether it is in M version or A version..............If it is in M version.............then activate the Master data..........because SID gets generated during the activation of the Master data..................
To activate the Master data.................use the program : RSDDS_AGGREGATES_MAINTAIN...........
Then repeat the load.........
If the value does'nt exist in the table...............then first check the IP.............if the setting is only PSA..........then first update the request in the target...........if the setting is OK..............
Then go to the source system...............check in RSA3...........give the datasource here.........and check whether the value exist in the source system or not.................if not then check the R/3 tables.......that whether the value exist in the table or not..............if the value exist in the table............then check how data is getting populated in the Extract structure..........
Hope this helps.........
Regards,
Debjani.......

Plan cost of IW31 not updating when MRP4 of Material master is individual requirement

Hi,
When Individal/coll of MRP4 tab of Raw material is 1 Individual requirement, plan cost is not updating in Tcode IW31 Repair order. It is updating when MRP4 is 2 collective requirement.
Please let me know the possible reasons.
Thanks

Yongguo
The behavior you are seeing on your system is correct system behavior.
The system rolls costs/revenues up to the assigned wbs element
if an order or network activity is flagged for deletion so you
can archive orders/networks while the project is still 'alive' without
loosing information on costs/revenues.
The logic is that costs of deleted networks should not get lost but are
rolled up to the superior wbs-element.
SAP has the understanding that released activities are used immediately,
carry actual costs and, therefore, can not be deleted. To keep the
objects clearly arranged the reorganization run can be used to move
some objects (those with status DLFL) to the archive without losing
data (in the meaning of costs).
If you want to remove these costs of the WBS elements you have
to cancel the deletion flag of these networks, remove the planned costs
start network costing and save. You can then set the DLFL again and
the costs will not appear in the structure report.
Hope this helps.
Best regards
Martina

Changes are not reflected when objects transported from Quality to Productn

Hi
In case of moving some Transport requests from Quality to Production, some times the changes made to the selection screen of a report program doesn't reflect in Production. Also we don't see any Transport error while transporting. Moreover, we can see the changes by regenerating the Program in production.
Would any one help me out in this with the reason for this.
Pls suggest what needs to be done.
Satish.

HI,
Thanks for the reply.
- I have checked the respective transport too, and every thing seems to be fine.
- Recently we went to go live, for the next release, so earlier before go live, we didnt faced any proble.. Only now we are facing this problem, that we find the changes relating to selection screen are not reflected when the object / prog is moved from qty to Prd.
- Only problem is with the selection screen.(not getting reflected in PRD. In Qty we are able to see those changes.
- Then in order to reflect these changes in PRD, we have to re generate the object, then only it get s updated..
Satish.
Edited by: satish c on Sep 22, 2009 3:35 PM

I cannot find information to help me change the orientation of a video filmed in portrait format but only able to be played back lying on its side (landscape) instead of upright. All the rotation buttons for iPhoto are not 'engaged' when it is in video .

I cannot find information to help me change the orientation of a video filmed in portrait format but it can only able to be played back lying on its side (landscape) instead of upright. All the rotation buttons for iPhoto are not 'engaged' when it is in video .

Thanks OT,
I tried the Export function but it would not allow me to choose the option of exporting to iMovie. I think you are right about needing Quicktime Pro. I opened iMovie and imported the clip from iPhoto and with some searching found the 'cropping, rotation' mechanism. So I now have a copy in the correct orientation. I plan to import/export it back to iPhoto because I want to have a copy on my iPhone to show people and I wanted to have it available as part of a slideshow I am making in iPhoto of my recent overseas trip. It is a pain that there is no simple orientating tool for the movie clips downloaded to iPhoto with the photos from the one camera.

PSE 8 some photos will not autoimport when creating an photobook and block the whole sequence. Are there knows reasons why individual photos can hang the import? Thanks Michael

When creating photobooks with PSE 8 I find occasionally that certain photos block the autoimport function and none of the sequence are loaded into the new photobook. Using the identical setting to create a photobook other sequences of photos work perfectly. The photos have been checked and found and all are connected and recognised. Are there knows issues with some photo formats which will not autoimport when creating a photobook?
Thanks for the help.
Michael

Sometimes LR can be "nudged" into showing folder relationships which better match the file system, by using the "show parent folder" command. When existing folders appear as if they were "top level" in the drive, we can see a more or less virtual picture of the situation, rather than anything real. So newly added folders can sometimes present themselves as if independent of what is already there.
By forcing LR to show a fuller hierarchy of folders, more attention gets paid to the actual arrangement - so new and existing folders should "wake up" and thereafter appear more reliably in the right relationships.

My sistem preferences are not working, when I try to change the photo of the desk It stop working, what can i do?

my sistem preferences are not working, when I try to change the photo of the desk It stop working, what can i do? I'm dieing cause I'm afraid

Have you tried resetting your device by pressing and holding the Home button and power button until the silver apple appears?

Emails are not generated in CUP To approver, manager

Hi ALL,
I Configured one work flow in CUP. I did SMTP Server setting, EMAIL Remainder setting.
When I create new account request , CUP is provisioning access properly and automatic mail is going to that user. Mail is not coming to Approve r.
When I create other requests (change account etc) provisioning is done properly, but mails are not generated to user, approve r, manager .?
How can I fix this? Please suggest.
Thanks,
Joseph

Joseph,
There can be only 2 issues here:
1) SMTP server config is not correct or CUP is not able to reach SMTP server.
Ask Basis person to ping the SMTP server from CUP. If it works, then don't worry about 1).
2) Email reminder job is not running or emails are going to junk email
Check the log for email reminder job and make sure it is activated and running. check your junk mail folder.
Rgds,
Alpesh

Mails are not generated in background Jobs and not shown in SOST.

Dear All,
I have facing issue regarding to system mails. I want to send mails the various reports automatically from SAP System to different recipients. So I scheduled that reports at background and in their spool list recipient I have added distribution list.
But that mails are not generated, it is not shown in transaction SOST also. When I send mails manually it goes successfully to only our company domain recipients. But not other domains. How should I resolve this problem?
Please help me out.
Thanks in advance.
Amit

Hi Srihari,
I have checked the background jobs they showed it finished. Following logs are shown in job logs. Is problem is due to 3rd log??
18.03.2012 14:23:34 Job started    00           516          S
18.03.2012 14:23:34 Step 001 started (program RFITEMAP, variant PDC FARMAR, user ID DEVELOPER1)      00           550          S
18.03.2012 14:23:37 No items selected (see long text)                                              MSITEM         033          I
18.03.2012 14:23:42 Spool request (number 0000026302) created without immediate output               SY           355          S
18.03.2012 14:23:46 Job finished                                                                     00           517          S
When I saw further details of 3rd log it following message.
No items selected (see long text)
    Message no. MSITEM033
Diagnosis
    No line items meeting your selection criteria could
    be for the following reasons:
    1.) No corresponding items have been posted.
    2.) You are not authorized to display this data.
    3.) The items have already been archived.
Please help me out.
Thanks
Amit

Change pointers are not generated when creating a material master

Similar Messages

Maybe you are looking for