Change STB name in Mobile Remote

Is there a way to change the STB name in Mobile Remote? Currently, they show up as STB1, STB2, STB3 and STB4.
I would like to be able to name them the way I have on the 'My Verizon' page as Living_Room, Den, Bedroom, Basement.

You should be able to rename your Set Top Boxes by doing the following:
1.  Log into your home router
2. Click on the My Network Icon
3. Locate the Set Top Box in the list
4.  To the right of the device listing click the button that says "rename"
Let me know if you need any further assistance.  Thank You for Choosing Verizon
Eric_VZ
Notice: Content posted by Verizon employees is meant to be informational and does not supersede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or Plan.

Similar Messages

  • HP pro 6200/6300 sff Change product name in bios remotely

    Hi,
    Is it possible to change the product name in the bios massivly or remotely?
    Because a lot of mainboards has been replaced by hp and they didn't set the name correctly. A wide of variaty of names for the same models is the result.
    But i need it per model the same for all computers.
    How to do this?
    Thanks

    Hi:
    Here is what you need to do...This model doesn't need the asset tag or serial # change utility...
    After entering BIOS Setup by hitting the F10 key, press Ctrl+A to open additonal fields in Security>System IDs menu.
    Enter your PC's serial number in Asset Tag Number and Chassis Serial Number fields.
    Save changes there and again when you exit the BIOS.
    Paul

  • HT5287 How do I change the name, Under Devices, of Remote Disk or Untitled to a name that reflects what I want.  In this case" Flash" for USB thumb drives.  Also will this create confusion when I connect my Superdrive?  Meaning, will it still be called FL

    I want to change the name under DEVICES, left column Remote Disk, Untitled  to FLASH USB, and still have it read my Superdrive when I connect it? 

    Each Volume (partition) on a device has a name.
    When it is mounted it will appear with that name as an icon on the desktop, and under devices in the sidebar.
    Typically a USB flash drive would only have one volume.
    They may initially come with names like Untitled or No_Name etc. 
    When mounted you can rename any USB drive (Or individual Volume if there is more than one partition) by using the mouse to select the name on the Desktop and hold the selection in you can edit the name. That name will stay with that particular drive and will show every time it is mounted.
    CDs and DVDs may well have a name which will show when they are mounted. When you make a CD or DVD you can provide a name when making it.
    It is good practice to name a new thumb drive or USB disk when you get it to avoid the confusion you seem to be having. Simialrly to name any DVDs or CDs you create

  • Unable to use FiOS Mobile Remote App on Samsung Galaxy Tab 2

    I'm one of the holdout Blackberry customers who Verizon doesn't recognize as wanting apps anymore.  I finally broke down and bought an Android tablet device when I saw the FiOS Mobile Remote App and recognized it as an easy solution for controling my multiple HD STBs in my "Man Cave".  Unfortunately, the app has been completely useless.
    The app loads fine.  I'm able to register each HD STB with the app, however doing anything more than the initial set-up for the remote function results in a crash.  Every time I attempt to use it, I get the message "Unfortunately, FiOS Remote has stopped."  I will occassionally see the attempted connection displayed on the corner of my TV screen.
    All other functions of the app work, including the DVR function.
    I've reported this failure for months, using the handy little report button below the crash message.  No response.
    I've commented on this topic in threads from other users with the same problem.  No response.
    I've posted to the comments section of the Google Play store.  No response.
    Please, would someone from Verizon acknowledge this problem exists?  My best theory so far is that my tablet device is not on a Verizon data plan (WiFi only), so therefore Verizon isn't interested in supporting it (or this loyal customer). 
    Device is Samsung Galaxy Tab 2, 7.0, running Android 4.0.4.  All FiOs STBs replaced with latest generation.

    I am sorry to hear about the troubles you are having with the app. We try to make the app as compatible with all devices as possible. The full list of devices the mobile remote is compatible with is https://www22.verizon.com/OnDemand/unprotected/AboutFlexView.aspx   . You may find there may be devices that do work with it that re not on the list, but these are all verified working devices with the app. Since yours doesn't appear to be on the list, we can not gaurantee it will work. Submitting all the feedback has gotten word back to Verizon about the troubles you are having. You can also submit this to the Verizon Idea Exchange. Please search on the idea exchange and cast your vote. There may be another member who made the same suggestion. If not, please add a new idea so your fellow community members can comment and vote on your suggestion. http://forums.verizon.com/t5/Verizon-Idea-Exchange/ct-p/ideaexchange  . The Verizon Idea Exchange is there for you to submit your ideas and suggestions to Verizon so that we can consider them as we innovate our products and services.
    Anthony_VZ
    **If someones post has helped you, please acknowledge their assistance by clicking the red thumbs up button to give them Kudos. If you are the original poster and any response gave you your answer, please mark the post that had the answer as the solution**
    Notice: Content posted by Verizon employees is meant to be informational and does not supersede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or plan

  • Ask the Expert: Plan, Design, and Implement Mobile Remote Access, the Cisco Collaboration Edge Architecture

    Welcome to the Cisco® Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about planning, designing, and implementing mobile remote access (Cisco Collaboration Edge Architecture) with Cisco subject matter experts Aashish Jolly and Abhijit Anand.
    Cisco Collaboration Edge Architecture is an architecture that provides VPN-less access of Cisco Unified Communications resources to Cisco Jabber® users. This discussion is dedicated to addressing questions about design best practices while implementing mobile remote access.
    For more information, refer to the Unified Communications Mobile and Remote Access via Cisco VCS deployment guide. 
    Aashish Jolly is a network consulting engineer who is currently serving as the Cisco Unified Communications consultant for the ExxonMobil Global account. Earlier at Cisco, he was part of the Cisco Technical Assistance Center (TAC), where he helped Cisco partners with installation, configuring, and troubleshooting Cisco Unified Communications products such as Cisco Unified Communications Manager and Manager Express, Cisco Unity® solutions, Cisco Unified Border Element, voice gateways and gatekeepers, and more. He has been associated with Cisco Unified Communications for more than seven years. He holds a bachelor of technology degree as well as Cisco CCIE® Voice (#18500), CCNP® Voice, and CCNA® certifications and VMware VCP5 and Red Hat RHCE certifications.
    Abhijit Singh Anand is a network consulting engineer with the Cisco Advanced Services field delivery team in New Delhi. His current role involves designing, implementing, and optimizing large-scale collaboration solutions for enterprise and defense customers. He has also been an engineer at the Cisco TAC. Having worked on multiple technologies including wireless and LAN switching, he has been associated with Cisco Unified Communications technologies since 2006. He holds a master’s degree in computer applications and multiple certifications, including CCIE Voice (#19590), RHCE, and CWSP and CWNP.
    Remember to use the rating system to let Aashish and Abhijit know if you have received an adequate response. 
    Because of the volume expected during this event, our experts might not be able to answer every question. Remember that you can continue the conversation on the Cisco Support Community Collaboration, Voice and Video page, in the Jabber Clients subcommunity, shortly after the event. This event lasts through June 20, 2014. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.

    Hi Marcelo,
       Yes, there are some requirements for certificates in Expressway.
    Expressway Core (Exp-C)
    - Can be signed by either External or Internal CA
    - Better to use a cluster name even if you start with 1 peer in Exp-C cluster. In the future, if more peers are added, changes would be minimal.
    - Better to use FQDN of cluster as CN of certificate, this way the traversal zone configuration on Expressway-E won't require any change even if new peers are added to Exp-C cluster.
    - If CUCM is mixed mode, include security profile names (in FQDN format) as Subject Alternate Names
    - The Chat Node Aliases that are configured on the IM and Presence servers. They will be required only for Unified Communications XMPP federation deployments that intend to use both TLS and group chat. (Note that Unified Communications XMPP federation will be supported in a future Expressway release). The Expressway-C automatically includes the chat node aliases in the CSR, providing it has discovered a set of IM&P servers.
    - For TLS b/w CUCM, IM-P & Exp-C
      + If using self-signed certificates on CUCM, IM/P. Load Cisco Tomcat, cup, cup-xmpp certificates from IM-P on Exp-C. Load callmanager, Cisco Tomcat certificates from CUCM on Exp-C.
      + If using Internal CA signed certificates on CUCM, IM/P. Load Root CA certificates on Exp-C.
      + Load CA certificate under tomcat-trust, cup-trust, cup-xmpp-trust on IM-P.
      + Load CA certificate under tomcat-trust, callmanager-trust on CUCM.
    Expressway Edge (Exp-E)
    - Signed by External CA
    - Configured Unified Communications domain as Subject Alternate Name
    - If using a cluster, select FQDN of this peer as CN and FQDN of Cluster + this peer as Subject Alternate Name.
    - If XMPP federation is being deployed, enter the same Chat Node Aliases as entered in Exp-C.
    For more details, please refer to the Certificate Creation Guide for Cisco Expressway x8.1.1
    http://www.cisco.com/c/dam/en/us/td/docs/voice_ip_comm/expressway/config_guide/X8-1/Cisco-Expressway-Certificate-Creation-and-Use-Deployment-Guide-X8-1.pdf
    - Aashish

  • Unable to use Fios Mobile Remote with Droid phone

    I go through mobile remote registration and i keep getting a message that says "sms error   unable to process your request at this moment, please ry again. If the problem continues, please try restarting your set-top box ".   I have rebooted and tried tech support and have been unable to resolve the concern.  Has anyone had this similar issue resolved?  Thank you.
    Solved!
    Go to Solution.

    Hey jsolis, did the mobile remote work for you before check if the STB is getting an ip address if its not then unplug the power cord and unscrew the coax cable for 10secs rescrew the coax cable then plug the power cord back in after the reset try it again.  If that does not work then delete the app on the phone and download it again. 
    Ron
    Verizon Telecom
    Fiber Solution Center
    Notice: Content posted by Verizon employees is meant to be informational and does not supercede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or Plan. Follow us on Twitter™!

  • How to change domain name from "LocalHost" to ipaddress in Jdeveloper?

    Hi
    When i run any application from JDeveloper, the page opening with the URL keeping "*LocalHost*" as a domain name,
    eg: http://*localhost*:7101/Testing/faces/index.jsf
    How can i change the domain name from "localHost" to my system's ipaddress. So that whenever i execute the page, the page should open with the ipaddress and not with "localhost", like http://*10.34.65.175*:7101/Testing/faces/index.jsf
    Regards
    Raj

    Thank you Timo.
    I changed domain name from "localhost" to ipaddress as you said, after that the server stopped working. Unable to run any application.
    Then I changed it back to "localhost" and its working fine.
    I am doing it for 2 reasons,
    1) With localhost as domain name, I am unable to open ADF mobile browser application in Android emulator.
    2) Unable to do remote debugging. Hope this could be the reason.
    Regards
    Raj

  • HT4437 I have a Pioneer VSX-1012-K and i want to change the name of it on my iphone to something elce. Is there any way i can do this.

    I have a Pioneer VSX-1012-K airplay amp and I want to change the name of it when i am using AirPlay. Is there any way i can do this?

    If it is showing off line, either the battery is dead, the SIM has been removed or the iPhone has been restored. Report it to you carrier. Some offer blacklisting. You can also send a remote wipe to the phone via iCloud. There was also the option to send you an email if the phone is located when you were in Find My iPhone. Report it to law enforcement, change the passwords on all accounts that were on the device. Did you have a passcode on it?

  • Can we change the name of the cookie - JSESSIONID?

    Can we change the name of the cookie- JSESSIONID?
    for eg.
    Set-Cookie = [ JSESSIONID=6ad8360e0d1af303293f26d98e2a; Version=1; Comment=Sun+ONE+Application+Server+Session+Tracking+Cookie; Path=/]
    can we change it to something like -
    Set-Cookie = [ ServletSession=RkA4OlbgfW; path=/]

    Thankyou Sultal for the response.
    Actually we are migrating the application server from Weblogic5.1 to Sun application server 8.2. The client is a mobile client and it sends the Cookie as 'JSESSIONID=session_id_val&WeblogicSession=session_id_val' as parameters, not as request header.It worked fine for Weblogic5.1 but not in Sun Application Server.
    To make it clear :
    Weblogic           :     request.getsession(false) = sessionObj@value
    Sun Application Server      :     request.getsession(false) = null
    Sun Application Server      :     request.getParameter("JSESSIONID") = session_id_val
    In the Weblogic5.1 we have set the cookie & session parameters in the weblogic.properties file as:
    weblogic.httpd.session.cookies.enable=true
    weblogic.httpd.session.cookie.name=WebLogicSession
    weblogic.httpd.session.neverReadPostData=false
    weblogic.httpd.session.timeoutSecs=120
    In case of Sun application server , JSESSIONID is not coming as a cookie , request.getsession(false) is returning null value.Is there a way to initialize the session with JSESSIONID request parameter?

  • How do I change owner name?

    Hello everyone,
    I just purchased a used laptop and was wondering how I change the previous owners information.
    They gave me their password, etc to logon, but I want to completely change the name.
    Is this possible?
    Thanks a lot for any help.

    Mac OS X: How to change user short name or home directory name
    -Bmer
    Mac Owners Support Group - Join us @ MacOSG.com
      Mac611 Mobile Mac Support - about.Mac611.com
       iTunes:MacOSG Podcast | YouTube.MacOSG.com
                       An Apple User Group 
    Have an iPhone or iPod touch? Enter Mac611.com in Safari on it for 'mobile Mac support.'

  • IPhone changes contact name

    I have an iPhone 3G running OS 3.0
    I have a contact stored as a first name only, Mobile and email.
    When ever i receive an email from him, The iphone automatically changes his stored name to the one written in his email name.
    What is the reason please ? and how can solve it please ?
    Thanks

    I have the same issue with my 3G. What I found out is that - apparently - the Address Book was made for people with First AND Last names, so if you don't use one of them when you receive an e-mail from this person it will automatically changes the contact field, using that one registered with the email. The only solution for me until now was to mark those contacts that I use only the first or the last name as COMPANY. That seems to solve the problem, but I'm still hoping to find a more effective way out.

  • Mobile remote iphone/iPad app

    I'm trying to connect my iPhone and iPad to my DVR using the fios app. I can set the DVR to record just fine but when i am trying to set up the mobile remote it is not working. I get to the widget on the DVR and go to fios mobile remote. I click on register a mobile remote. From here it just gives me a pin but does not ask me what type of device I have or anything.  When I open the app on my phone it doesn't ask for the pin at all  It just says it fails to connect. The message on the tv says 'only mobilat devices that are part of this household can access this account. I can't figure out why this isn't working. 

    That's my experience too.. I can use the app to watch shows on my iPad and i can set a show to record to my Dvr.  I can browse stuff already recorded on my dvr.  But I cannot get the app to 'pair' with set top box so I can use the app as a remote control... Right now when try touch the 'play on TV'  button, i say 'pair' it, and I get a message that it can't find any set top box,
    my set to box does show up properly in the settings, and as I mentioned, I can easily browse recorded shows.
    but..  I did get it to pair ONCE.  It worked as a remote just great.  I was delighted.  But didn't want to use my main Verizon I'd and password on my husbands and my iPads.  So I set up a sub account just for TV live access.
    then I logged out of the app and logged in with the new I'd.  All loaded fine, but it would not pair with my set top box.  I logged out and logged back with my main account.  Again, it would not pair.   I unplugged my stb, powered it back on, let it initialize, but it he app still wouldn't pair.  I reset my iPad.  Still no pairing,
    so now I'm stuck.  It seems unreasonable that I would have to reboot my router, but that's the only thing left..  Obviously SOMETHING isn't working properly on the pairing process since all other functions work properly.  The only thing that doesn't work is my iPad acting as a remote control.
    i did send in a feedback hoping it would get to the app developers.  
    Janet

  • Widgets not showing up on TV screen - esp FIOS Mobile Remote app

    When I press Wdigets on my remote - the tool bar appears on top of the tv screen.  However, when scrolling through, some of the Widgets appear w/ blank information. 
    I want to install the FIOS mobile tv remote and that widget also does not appear to be in my options.
    Should I reset my box?  How can I fix?
    Jessica

    Hi Jessica,
    The FiOS mobile remote widget is located inside the main FiOS TV widget menu.  This should be the first screen you see up top when you hit the Widgets button on your remote.  Once you hit OK, go down to 'Featured' and you should see the mobile remote widget on the right.  If you are still having trouble with the widgets screen displaying blank information, you can reset your box in one of two ways.  You can unplug it from the power for 30 seconds, or if the power cord is difficult to get to, hit menu on the FiOS remote, go down to 'Customer Support' then to 'In-Home Agent' then 'Reboot Set-Top Box', hitting OK here will have your box cycle through.  Then try the Widgets again, if you are still having trouble feel free to PM me.
    --James
    --James
    Verizon Support
    Notice: Content posted by Verizon employees is meant to be informational and does not supersede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or Plan.

  • 10.5 server changes host name when changed to be member of 10.4 OD Master

    Hi,
    I have a Xserve with 10.4.11. This is my working OD master hostname: AAA, FQDN: AAA.domain, realm DOMAIN. Now I have a PowerMac G5, hostname BBB, FQDN BBB.domain, where I install 10.5 server.
    When it comes up as stand alone, the hostname is BBB (FQDN BBB.domain), but when I then connect it (as domain member) to my OD master, it promts me to say that "AAA" is a used hostname and that it changes hostname to" AAA (2)".
    In my DNS it is still identified as BBB.domain, and it is bind to the realm as BBB.
    Why does it act like this?
    Subsequently I can't get kerberos to work and SMB does not want to be a member of the domain (always get back to standalone instead of becoming member of the domain).

    Here comes a bit more on this one. I waited and maybe this had to do with having a OD master in Tiger and the OD member on Leopard. But now both are in Leopard. And things are the same.
    I have thou been studying the Console after some tips. And I'm changing the host name in Server Admin/Network to BBB (what it should be). And it seems to work fine. Name of the server changes where supposed to (what I can see). And in Console I can se that the administration tool changes host name in a variety of places.
    And now I wait.
    If I do nothing (the network is pretty small), nothing happens. But after a while, I login with for example Remote desktop the followingapears in Console:
    +Jan 3 12:58:02 emil mDNSResponder[30]: User updated Computer Name from AAA (2) to AAA+
    +Jan 3 12:58:02 emil mDNSResponder[30]: afpovertcp.tcp. service renamed from "AAA (2)" to "AAA"+
    +Jan 3 12:58:02 emil mDNSResponder[30]: ssh.tcp. service renamed from "AAA (2)" to "AAA"+
    +Jan 3 12:58:02 emil mDNSResponder[30]: sftp-ssh.tcp. service renamed from "AAA (2)" to "AAA"+
    +Jan 3 12:58:02 emil mDNSResponder[30]: servermgr.tcp. service renamed from "AAA (2)" to "AAA"+
    +Jan 3 12:58:02 emil mDNSResponder[30]: rfb.tcp. service renamed from "AAA (2)" to "AAA"+
    +Jan 3 12:58:02 emil mDNSResponder[30]: ldap.tcp. service renamed from "AAA (2)" to "AAA"+
    +Jan 3 12:58:02 emil mDNSResponder[30]: net-assistant.udp. service renamed from "AAA (2)" to "AAA"+
    +Jan 3 12:58:02 emil mDNSResponder[30]: adisk.tcp. service renamed from "AAA (2)" to "AAA"+
    +Jan 3 12:58:02 emil mDNSResponder[30]: User updated Local Hostname from AAA-2 to AAA+
    +Jan 3 12:58:03 emil mDNSResponder[30]: Local Hostname AAA.local already in use; will try AAA-2.local instead+
    +Jan 3 12:58:03 emil mDNSResponder[30]: afpovertcp.tcp. service renamed from "AAA" to "AAA (2)"+
    +Jan 3 12:58:03 emil mDNSResponder[30]: ssh.tcp. service renamed from "AAA" to "AAA (2)"+
    +Jan 3 12:58:03 emil mDNSResponder[30]: sftp-ssh.tcp. service renamed from "AAA" to "AAA (2)"+
    +Jan 3 12:58:03 emil mDNSResponder[30]: servermgr.tcp. service renamed from "AAA" to "AAA (2)"+
    +Jan 3 12:58:03 emil mDNSResponder[30]: rfb.tcp. service renamed from "AAA" to "AAA (2)"+
    +Jan 3 12:58:03 emil mDNSResponder[30]: ldap.tcp. service renamed from "AAA" to "AAA (2)"+
    +Jan 3 12:58:03 emil mDNSResponder[30]: net-assistant.udp. service renamed from "AAA" to "AAA (2)"+
    +Jan 3 12:58:03 emil mDNSResponder[30]: adisk.tcp. service renamed from "AAA" to "AAA (2)"+
    +Jan 3 12:58:03 emil mDNSResponder[30]: User updated Computer Name from AAA to AAA (2)+
    +Jan 3 12:58:03 emil mDNSResponder[30]: User updated Local Hostname from AAA to AAA-2+
    +Jan 3 12:58:03 emil mDNSResponder[30]: mDNS_SetFQDN - hostname unchanged+
    "AAA (2) to AAA" may as well be "BBB to AAA". But I'm very surprised over that the logg claims that "User updated Computer name..." For all I know, I haven't. And note in the middle here that the mDNSResponder changes to AAA (which indeed is used - it's the OD master!!!), discovers that the name is in use, and then changes to "AAA (2)".
    But why does it at all initiate a change from AAA to "AAA (2)"?
    Why can't I call the server BBB?

  • A simple change of name request not so simple

    I have sent in my details to allow a change of name and when trying to find out if it's complete I have been hung up on 3 times, on hold for in excess of 30 mins before being hung up on and told a simple change of last name will take FIVE WORKING DAYS!!!!
    Ridiculous is all I can think.
    Have been with O2 a really long time and can't believe how ridiculous my recent interaction with you has been.
    Can someone please get my last name changed so I can refresh my account and upgrade my phone and stay with O2 for a further decade OR I will move on to another company. Simple as that.

    Change of name account
    Send a copy of the marriage certificate  with a covering letter giving details of all the account numbers you have with O2. (For example mobile, broadband, home phone.) to:
    The Correspondence Management Team
    PO Box 202
    Houghton Regis
    LU6 9AG
     Or via email with the scanned proofs to [email protected]
    Or via fax with the scanned proofs to 0870 6002402.

Maybe you are looking for