Change the resolution for more files/tracks at the same time?

Hello,
we are now recording about 1000 LP to 32 bit (float) resolution for our archive, but for our and public use we will need 16 bit resolution. Is there any possibillity to change the resolution for more (for example 100 files) at the same time?
IASA recommendations:
http://www.iasa-web.org/tc04/introduction-first-edition
»It is recommended that all audio be digitised at 48 kHz or higher, and with a bit depth of at least 24 bit.«
Thank you.

Sure
Go to edit view select File->Batch Processing.
Then select your files and resample settings
Too easy.

Similar Messages

HT1379 My computer I-mac is running super slow. If I zap the PRAM it goes back to running well , briefly... a few hours, then back to super slow. What is the resolution for this problem? I have a Time machine that does back up well.

My computer is running super slow. I can correct the problem briefly by zapping the PRAM but is resumes as a problem after a few hours. I have good time machine (capusle) backup daily. I have done a disk verify and there doesn't appear to be anything wrong there.
Help, this is wasting a lot of time to do simple functions.

Hard to say what's going wrong without more information. Try the troubleshooting steps in my Mac Performance Guide. Post back if you need help with any of that or questions about the results.

I'm running out of hd space on my MBP with Mavericks. How do I move my Photoshop 5 app off the computer for more space. How can I store the PS5 app on DVD or on my backup hd for a future reinstall on my next Mac?

I'm running out of hd space on my MBP with Mavericks OS. How do I move my Photoshop 5 app off the computer for more space, and store the PS5 app on DVD or on my backup hd for a future reinstall on my next Mac with larger hd?
Thanks

slaglejrp,
perhaps it would be less expensive to just install a new disk with a larger capacity on your current MacBook Pro, rather than plan on buying a new Mac with a larger disk? Once your current disk has been cloned to the new disk, and the new disk has been installed into your MacBook Pro, that would allow you to keep Photoshop 5 on your current MacBook Pro.

How to reliably check the resolution for a pdf file?

Should I use preflight to reliably check the resolution for a pdf file? I have posted my frustrations on http://forums.adobe.com/thread/978098

You can create your own preflight tool to check for the dpi of embedded images.

HT201272 My apple tv keeps telling me to go into itunes to change the Resolutions for a quicker download---how do I do this ?

My apple TV keeps telling me to go to itunes to change the resolutions for quicker download---how do I do this after I have gone into itunes---where to next?

It will say restoring apple tv but the progress bar will not move at all. I have left it running for six hours with no change. I get a 1602 error device not found after I unplug it to start over. My iTunes recognizes the device and tries to update it, but the same thing happens again.

F4 Help to get the path for a File source directory

There are numerous function modules for browsing a particular file in desktop and getting the file path (including the fine name) , like F4_FILENAME , KD_GET_FILENAME_ON_F4 , WS_FILENAME_GET etc. But can anyone tell me how to fetch only the directory path to the field were the F4 help is given. Actually the filename has to come in some other field in the selection screen. Is there separate funtion modules for these OR will changing parameters in the above function modules work?
Pls Help....
Also are there function modules for providing F4 help for getting the path to a file in application directory?

Try this method CL_GUI_FRONTEND_SERVICES.
It is a Global CLASS which is having different methods for different purposes
see the documentation of it and use the methods of it
see
CL CL_GUI_FRONTEND_SERVICES
Short Text
Frontend Services
Functionality
The class CL_GUI_FRONTEND_SERVICES contains static methods for the following areas:
File functions
Directory functions
Registry
Environment
Write to / read from clipboard
Upload / download files
Execute programs / open documents
Query functions, such as Windows directory, Windows version, and so on
Standard dialogs (open, save, directory selection)
Example
Determine the temp directory on your PC:
DATA: TEMP_DIR TYPE STRING.
CALL METHOD CL_GUI_FRONTEND_SERVICES=>GET_TEMP_DIRECTORY
CHANGING
TEMP_DIR = TEMP_DIR
EXCEPTIONS
CNTL_ERROR = 1
ERROR_NO_GUI = 2.
IF SY-SUBRC 0.
Error handling
ENDIF.
flush to send previous call to frontend
CALL METHOD CL_GUI_CFW=>FLUSH
EXCEPTIONS
CNTL_SYSTEM_ERROR = 1
CNTL_ERROR = 2
OTHERS = 3.
IF SY-SUBRC 0.
Error handling
ENDIF.
WRITE: / 'Temporary directory is:', TEMP_DIR.
Notes
The class CL_GUI_FRONTEND_SERVICES is based on the Control Framework. See the documentation for more information, in particular on CL_GUI_CFW=>FLUSH which must be called after many CL_GUI_FRONTEND_SERVICES methods.
Migration Information
The old file transfer model was based on function modules of the function group GRAP. The old features have been replaced by the class CL_GUI_FRONTEND_SERVICES. The following list contains the old function modules (italic) and the new methods (bold) that replace them:
CLPB_EXPORT
CLIPBOARD_EXPORT
CLPB_IMPORT
CLIPBOARD_IMPORT
DOWNLOAD
GUI_DOWNLOAD, dialog replaced by FILE_SAVE_DIALOG
PROFILE_GET
No replacement, use REGISTRY_* methods instead
PROFILE_SET
No replacement, use REGISTRY_* methods instead
REGISTRY_GET
REGISTRY_GET_VALUE, REGISTRY_GET_DWORD_VALUE
REGISTRY_SET
REGISTRY_SET_VALUE, REGISTRY_SET_DWORD_VALUE
UPLOAD
GUI_UPLOAD, dialog replaced by FILE_OPEN_DIALOG
WS_DDE
Obsolete: This function is no longer supported.
SET_DOWNLOAD_AUTHORITY
Obsolete: This function is no longer supported.
WS_DOWNLOAD
GUI_DOWNLOAD
WS_DOWNLOAD_WAN
Obsolete: This function is no longer supported.
WS_EXCEL
Obsolete: This function is no longer supported.
WS_EXECUTE
EXECUTE
WS_FILENAME_GET
FILE_SAVE_DIALOG, FILE_OPEN_DIALOG
WS_FILE_ATTRIB
FILE_SET_ATTRIBUTES, FILE_GET_ATTRIBUTES
WS_FILE_COPY
FILE_COPY
WS_FILE_DELETE
FILE_DELETE
WS_MSG
Obsolete: This function is no longer supported.
WS_QUERY
CD (current directory)
DIRECTORY_GET_CURRENT
EN (read/write environment)
ENVIRONMENT_GET_VARIABLE
ENVIRONMENT_SET_VARIABLE
FL (determine file length)
FILE_GET_SIZE
FE (check if file exists)
FILE_EXIST
DE (check if directory exists)
DIRECTORY_EXIST
WS (determine Windows system)
GET_PLATFORM
OS (operating system)
GET_PLATFORM
WS_UPLDL_PATH
Obsolete: This function is no longer supported.
WS_UPLOAD
GUI_UPLOAD
WS_VOLUME_GET
Obsolete: This function is no longer supported.
Reward points if useful.

How to find the resolution of media files in mac

how to see the resolution of media files in mac?
WIndows show the resolution when putting the mouse over the file.

Hi Austin
I should have describe more clearly.
What I mean is for video files, I cannot see the resloution of the file. For example, 1980x1080 or 1080x720 so on
Sometimes they do show

Making Adobe 7.0.5 the default for .pdf files

I was advised that the way to get Adobe 7.0.5 to be the default, instead of 5.0, was to delete the Adobe applications & files in my system, library, and user folders, including the 7.0.5 app. itself. Then, after everything relating to Adobe is gone, I should re-install 7.0.5 and it would become the default.
I also heard that Spotlight won't find every Adobe component or extention, so I'd have to do a detailed search and delete each one that way.
Does this sound right?
Can't I just delete the 5.0 folder in the Applications (Mac OS 9) folder and have everthing associated with 5.0 gone? Isn't that the beauty of having a Mac?
Thanks,
Greg
PowerBook G4 15" Mac OS X (10.4.2) 1.5 GHz, 1.5 GB RAM

Hi Greg
You were poorly advised. Deleting Adobe apps is a headache and completely irrelevant when it comes to making an app the default for a file type.
Control-click a .pdf file, choose Get Info. In the Info window click the Open With drop down list, choose the app you want, and then click Change All underneath it.
That should do it. You might find that there is more than one type of .pdf file and you might need to perform this action again at some time, but this should do the job.
And yes, you can just delete the Acrobat Reader 5.0 folder.
Matthew Whiting

How can I change the gain on one audio track in the selection?

How can I change the gain on one audio track in the selection? Is there a way to adjust the gain as it is implemented for example in cubase - pull waveform up and gain varies?

I'm not sure what you mean by "in the selection", or, more honest: I don't understand that at all.
So, instead I'm going to tell you that you can indeed adjust the Gain of one or more selected region(s) in the Region inspector on the left hand side.

I have 3 older ext. hard drives that I've utilized many times. Today while searching for old files, one of the three is no longer recognized by my PowerMac. Any suggestions?

I have 3 older ext. hard drives that I've utilized many times. Today while searching for old files, one of the three is no longer recognized by my PowerMac. The drive is not listed in Disk Utility. Any suggestions?

Is the computer in you equipment line:
Dual Core Intel Xenon
(which is not a PowerMac but a Mac Pro) the one you are asking about, or do you have an older PowerMac?
If a Mac Pro, their forums are here:
Mac Pro
and, as Mac Pros have a totally different architecture from the pre-2005 Macs this forum covers, you may not have the same issues that can affect the older models. If someone didn't notice your equipment line, you could get advice that doesn't apply.
If you really have a pre-2005 PowerMac, read on.
If the stubborn external is USB and does not have its own power brick (i.e., it gets power only from the computer's UBS ports--"bus powered"), it may not be getting enough power. As electric motors age, they can demand more power than when new, and the power available on any USB port is limited.
The typical workabouts to making a computer recognize an aging, bus-powered USB drive are:
Get a powered USB hub (has its own power brick
Get a "Y" USB cable: 1 Meter USB 2.0 A to 5 Pin Mini B Cable - Auxiliary USB "Y" Power Design for external hard drives.
The second gets power from two USB ports on the computer and often that's enough.
Remember that the USB ports on your keyboard seldom provide enough power even for a thumb drive, so be sure to use the USB ports on the back of the computer.

Error occured while converting the file track #1 the required disk can't be found

I have old CDs, I have new CDs and I have a relatively new MacBook Pro (3 years old) running current software on 10.9.4 OSX Mavericks. My updates are good on my iTunes but it won't let me import ANY CDs that I OWN! Is this the new Apple and it's iTunes update?
Can we not legally put our CDs onto our phones or iPad/iPods any longer? Must I go garage sale-ing for a personal CD player? The code reads; "Error occured while converting the file track #1 the required disk can't be found". My cd drive is fine btw. It reads and shows on my desktop and will also play when I double click the CD icon and play the .aiff file.

I kind of have the suspicion if you were no longer allowed to put CDs on iPods it would be front page news, not something you alone would discover. Anyway, there would probably be a clear message to that effect rather than a technical error message. I would take the technical problem route first rather than suspect you have been targeted for persecution.
Have you restarted iTunes? Have you tried restarting your computer?
Personally I prefer third party rippers such as XLD and Max and you could certainly try one of those to at least isolate the issue to iTunes.

HT1766 I have made the C drive on my computer very small, with the intention that all data would be stored on the D partition. Can I change the destination for my iPad backup to the D drive?

I have made the C drive on my computer very small and try to put all the data on the D partition. Can I change the destination for my iPad backup to the D drive?

See if this post from turingtest2 helps : https://discussions.apple.com/message/24351688
If not then you might be better off asking in the iTunes For Windows forum, you may be more likely to get better help there.

Change status(Active/Inactive) of file adapter by the external command

Hi, all.
Is it possible to change status(Active/Inactive) of file adapter by the external command?
Let's say, like
"$ switch_file_adapter_status.sh <File Adapter name> <active|inactive>"
or something like that.
Actually, we have the following requirement for the file adapter.
For example, we have many "file adapter to R/3" scenarios and we only want to allow data transfer between 9:00 a.m. to 9:00 p.m.(R/3 service time).
In order to achieve this requirement, one option would be to switch file adapter status between active and inactive by external command line.
And this command will be controlled by the job scheduler(like Tivoli).
Does XI(3.0 or above) have this kind of feature?
Best Regards.

Hi,
I don't think that this is possible.
But one Solution for your problem could be a job on xi who execute the Queue.
So that Adapter work the hole time and send the Message to XI Queue which process them not automatically.
And the XI Queue you can trigger with a Job like normal R/3 Jobs.
Hope that helps,
Regards,
Robin

HT2493 How to change preview image of a file and NOT the icon ?

Hello dear Mac users
How to change preview image of a file and NOT the icon ?
I know how to change the icon of a file, but I wish to know how to change the preview of any file.
For example: my file is "mysong.aif", I changed the icon to be "mylogo.png" using cmd+i, cmd+v on the icon. But the preview of the file still remain the same.
I know it can be changed using iTunes, but I don't want to import all my files in iTune, and iTune cannot import all type of files.
I hope someone will understand my needs...
Thanks!

Thanks BeerbarX
You can't change the preview image for anything
hoo
QuickLook plugin
what are the plugin ?
In the case of a music file, it will be that generic black box with a note on it
That is exactly what I'm asking about !
MP3 which has a special tagging standard that can include artwork
How can I "tag" my MP3 without going thru iTunes ? Is it possible to do it dirrectly in the Finder ? Is there other type of files that can include such tags ?
Thank you for answering my question , wich I have to admit may seem useless, but I wish I could put something like a signature logo on each of the different file I produce (as AIF for music and MP4 for video clip) instead of that generic black box with a note on it, and by the meantime keeping a different icon for all of them in order to illustrate theire content.

Reversi Sample - "The project requires user input. Reload the project for more information."

A week ago, I downloaded the sample code examples. Then I extracted the reverse sample code, loaded it and ran it. All was well.
I was just using it as a resource for example code, so no code changes. Now, when I open the project, I get nothing loaded.
Solution explorer displays Solution 'Reversi' (0 Projects). Below that
"The project requires user input. Reload the project for more information."
This message shows for all three sections Reversi, ReversiGameComponet, and ReversiComponentTests.
Ok, so I figure I must have accidently changed something. So, I re-extract. Same message.
The only thing I can think of is that in the options, I changed the startup location for my projects. I like to keep my code projects on the d: drive, so I changed that to D:\!!!W8. I've always done this so that when I create a new project,
it does it in my project directory by default. Didn't change anything else such as the templates dir.
I did set this back to the c:....projects, as where templates are, but that didn't help. So, I reset to my projects directory.
My project that I created loads ok.
Suggestions?

A week ago, I downloaded the sample code examples. Then I extracted the reverse sample code, loaded it and ran it. All was well.
I was just using it as a resource for example code, so no code changes. Now, when I open the project, I get nothing loaded.
Solution explorer displays Solution 'Reversi' (0 Projects). Below that
"The project requires user input. Reload the project for more information."
This message shows for all three sections Reversi, ReversiGameComponet, and ReversiComponentTests.
Ok, so I figure I must have accidently changed something. So, I re-extract. Same message.
The only thing I can think of is that in the options, I changed the startup location for my projects. I like to keep my code projects on the d: drive, so I changed that to D:\!!!W8. I've always done this so that when I create a new project,
it does it in my project directory by default. Didn't change anything else such as the templates dir.
I did set this back to the c:....projects, as where templates are, but that didn't help. So, I reset to my projects directory.
My project that I created loads ok.
Suggestions?
Hi there,
Can you provide the link for the sample code example so I can download and try on my machine?
Regards,

Change the resolution for more files/tracks at the same time?

Similar Messages

Maybe you are looking for