Change WLC 5508 port speed

I connect a copper SFP on port 2 of WLC 5508 to a ASA 5510 firewall.  The links between two devices are down.  Since ASA 5510 only support 100 full, how do I change port speed on port 2 to 100.
Thanks

Does this mean, I couldn't change port speed on the WLC?
Yes you can.  You can change the speed setting to GIGABIT, nothing less. 
Why do I need to buy another Gigbit switch for 2 connection?
What do you mean by "another"????   Do you have an existing GigabitEthernet switch that you can connect the WLC into?
You need a GigabitEthernet port to connect the WLC's GigabitEthernet port.  And then you can have a FastEthernet port to connect the SAME SWITCH to your ASA.
WLC --- (1000BaseTx) --- Switch --- (10/100BaseTx) --- ASA
Does this make sense to you?

Similar Messages

  • WLC 5508 Distribution Ports

    Dear Community,
    i have a small Q that should we configure any of distribution port of WLC 5508 with speed 10/100 to connect it with cisco's 3750 on fastethernet port.
    By default WLC ports are gig ports so is there any comand or option to configure the port by decreasing its speedin wlc.
                                                                           OR
    could we connect them in the same status like wlc gig port wit switch 3750 fastethernet port and there will not any speed mismatch and it will work fine.Honestly on my behalf it will not work like this.
    please advise what is the best practice to do that.

    i have a small Q that should we configure any of distribution port of WLC 5508 with speed 10/100 to connect it with cisco's 3750 on fastethernet port.Won't work because the 5508 will negotiate to 1Gb only.

  • Port channel WLC 5508 and 3750

    Hi All,
    I want to configure Port channel for WLC 5508 and cisco 3750 Stack Switch. What changes I need to make on WLC and where?
    Thanks
    Jagdev

    Thanks Chris,
    LAG is enable on WLC, and Port channel is configured on 3750, Please see the configration and Port channel status below:-
    (Cisco Controller) >show lag summary
    LAG Enabled
    interface Port-channel14
    description Port Channel to WLC001
    switchport trunk encapsulation dot1q
    switchport mode trunk
    end
    sh etherchannel 14 summary
    Flags:  D - down        P - bundled in port-channel
            I - stand-alone s - suspended
            H - Hot-standby (LACP only)
            R - Layer3      S - Layer2
            U - in use      f - failed to allocate aggregator
            M - not in use, minimum links not met
            u - unsuitable for bundling
            w - waiting to be aggregated
            d - default port
    Number of channel-groups in use: 14
    Number of aggregators:           14
    Group  Port-channel  Protocol    Ports
    ------+-------------+-----------+-----------------------------------------------
    14     Po14(SD)        LACP      Gi1/0/22(I) Gi2/0/22(I)
    sh run int g1/0/22
    Building configuration...
    Current configuration : 209 bytes
    interface GigabitEthernet1/0/22
    description Trunk to WLC001 DistPort1
    switchport trunk encapsulation dot1q
    switchport trunk native vlan 254
    switchport mode trunk
    channel-group 14 mode active
    end
    sh run int g2/0/22
    Building configuration...
    Current configuration : 209 bytes
    interface GigabitEthernet2/0/22
    description Trunk to WLC001 DistPort2
    switchport trunk encapsulation dot1q
    switchport trunk native vlan 254
    switchport mode trunk
    channel-group 14 mode active
    end

  • WLC 5508 Syslog send to custom port

    We have added Splunk to a monitoring systems and I would like to send my wlc 5508 log messages to it.  We have the Syslog Data Inputs on that server are all TCP and we would like to maintain tcp only if possible. I do need to be on a custom port other than 514.  We are on 7.4.100.60 on a HA pair of 5508's.  Does any on have any insight on changing the syslog port number in the WLC config?

    I too am using Splunk for capturing WLC Syslog.  With regards to the destination port of the Syslog, I don't know how to change it.  However, to get around this I have set up a Splunk Forwarder with Syslog-NG.  Basically Syslog-NG listens on any port number/protocol you define and writes logs to a log file name $hostname$.log.  This means I could have x different WLCs sending Syslog to Syslog-NG on UDP 514 and Syslog-NG will write the syslog from each host to it's individual file.
    From their I've configured Splunk forwarder to monitor each file and forward the logs on to Splunk.  You can forward to any port/protocol you wish.
    Also remember to do this
    config logging debug syslog enable
    On the controller.  Otherwise you won't see the messages you expect.

  • WLC 5508 issue with 4 ports in portchannel

    Hi,
    We have one WLC 5508 and LAG is enabled on it but when we connect 4 cables to a distribution switch only 3 links are sending and receiving traffic and the 4th one is up with outgoing traffic from the distribution switch to WLC but nothing incoming.
    Some APs went down and refuse to be registered back to the WLC. when we shut down the 4th port everything is back to normal.
    the etherchannel config is identical and I can see all ports are active and not suspended :
    interface GigabitEthernet2/2/1
    description PortChannel-WLC1-Port1
     switchport
     switchport trunk encapsulation dot1q
     switchport trunk allowed vlan 60-67,2808,2922,2923,2932
     switchport mode trunk
     channel-group 99 mode on
    interface GigabitEthernet2/2/2
    description PortChannel-WLC1-Port2
     switchport
     switchport trunk encapsulation dot1q
     switchport trunk allowed vlan 60-67,2808,2922,2923,2932
     switchport mode trunk
     channel-group 99 mode on
    interface GigabitEthernet2/2/3
    description PortChannel-WLC1-Port3
     switchport
     switchport trunk encapsulation dot1q
     switchport trunk allowed vlan 60-67,2808,2922,2923,2932
     switchport mode trunk
     channel-group 99 mode on
    interface GigabitEthernet2/2/4
    description PortChannel-WLC1-Port4
     switchport
     switchport trunk encapsulation dot1q
     switchport trunk allowed vlan 60-67,2808,2922,2923,2932
     switchport mode trunk
     channel-group 99 mode on

    sh etherchannel 99 sum
    Flags:  D - down        P - bundled in port-channel
            I - stand-alone s - suspended
            H - Hot-standby (LACP only)
            R - Layer3      S - Layer2
            U - in use      N - not in use, no aggregation
            f - failed to allocate aggregator
            M - not in use, no aggregation due to minimum links not met
            m - not in use, port not aggregated due to minimum links not met
            u - unsuitable for bundling
            d - default port
            w - waiting to be aggregated
    Number of channel-groups in use: 38
    Number of aggregators:           38
    Group  Port-channel  Protocol    Ports
    ------+-------------+-----------+-----------------------------------------------
    99     Po99(SU)         -        Gi2/2/1(P)     Gi2/2/2(P)     Gi2/2/3(D)     
                                     Gi2/2/4(P)     
    Last applied Hash Distribution Algorithm: Fixed
    Gi2/2/3 is down becasue we had to shut down the interface because when it is up many APs refuse to register.

  • Wlc 5508 get error when use port-channel

    We have two wlc in the system 5508 and 4402.
    we config HA for 2 wlc, both wlc enable LAG
    When I connect 2 interface  of 5508 to 2 interface (in a port channel mode on, trunk, dot1q) of a
    couple of VSS switch, I cant management 5508 through web any more, and I still can do with 4402.
    If I  shutdown 1 port int the port-channel, it work well.
    Do you know what happen ?
    Thanks
    Duyen

    hi Scott,
    We have VSS ( 2 x 6509) trunk with (2 switch 4506).  one port of wlc4402 connect to one port of one swith 4506.
    2 ports of wlc 5508 conect to 6509, each port connect to one switch 6509.
    the config in VSS switch like this:
    interface gig1/1/1
    switchport trunk encapsulation dot1q
    switchport mode trunk
    channel-group 500 mode on
    interface gig2/1/1
    switchport trunk encapsulation dot1q
    switchport mode trunk
    channel-group 500 mode on
    etherchannel load-balancer src-dst-ip
    ( I dont see this command in running config)

  • Wlc 5508 webauth subnet mask change issue

    Recenly l changed the network subnet for a particular wlc interface and scope and also an upstream router and for some reason it would only allow me to use a /24 Host mask as my plan was to go to a /22 mask to allow for over 1000 hosts within this scope.
    The Upstream Router which is a  ( RV042 ) had the following original config :
         192.168.1.1
         255.255.255.0
    I have noticed this device will not let me change the mask from a /24 to a /22 as you can only change from a pre-defined list of masks and you cannot manually add any either..
    New Config
         10.10.0.10
         255.255.255.0
    WLC 5508 Controller Interface
         Original Config
          192.168.1.25
         255.255.255.0
         192.168.1.1
         New Config
         10.10.0.25
         255.255.252.0
         Scope
         Range : 10.10.1.10 - 10.10.3.254
         Mask : 255.255.252.0
         Network : 10.0.0.0
         Router : 10.10.0.10
    When l reconfigure to this addressing the wireless clients connect and get the new dhcp scope details but following this the webauth screen doesn't appear not allowing them to connect meaning there is no routing of traffic / internet access.
    If l modify the above interface and scope masks back to a /24 - 255.255.255.0 the the wireless clients connect and webauth appears to prompt them to accept the terms and conditions and connect thus giving them internet access.
    It looks like an issue with the mask ? The main reason l am trying to change the subnet addressing is because the standard /24 mask is not providing enough dhcp addresses and we have had times were the scope has been exhausted due to the public connecting and disconnecting as the lease perod of 2 hours holds onto the address before expiring meaning there is not enough available addresses for people to connect.
    I would of thought that the upstream router ( RV042 ) even though it is only a /24 mask would still route the traffic coming from a WLC Controller interface with a /22 mask ?
    Hopefully someone can suggest a solution ?
    Thanks Simon

    Hey Scott just getting back to this issue..   If for instance l can modify the wlc interface and Scope to have a /22 mask ( 1022 Hosts ) and my upstream Router ( Cisco RV042 ) can only provide a /24 or higher mask then does that mean l am still limited to a range of 254 hosts ( /24 Mask ) ?  Would this mean l need to look into replacing my upstream Cisco RV042 VPN Router ?

  • Why WLC 5508 shows message " Operator changed to 11g mode" & AP is rebooted

    Dear Sir,
    I have faced some problem with Cisco 1520 Series APs.
    Since few days, We got the log in wlc 5508 like this
    "AP 'MAPNSY#WMI3', MAC: ac:a0:16:5c:45:00 disassociated previously due to AP  Reset. Uptime: 0 days, 00 h 22 m 52 s . Last reset reason: operator changed 11g  mode."
    & then AP is rebooted.
    Here, I attached the screenshot of WLC 5508 Log.
    Plz, help us.

    Not the IP addr of the management interface.. I am telling about the Dynamic AP manager interface that you have configured which is for the AP to register..
    Please post in the output..
    show interface summary (mentioning the interface used for APs to join)
    Regards
    Surendra

  • WLC 5508 : session disconnected when one lag-port is down.

    Hello,
    I have a WLC 5508 ( version 6.0.182).
    When the port1 and port2 are connected ( The switch is configured with a etherchannel in forced mode) everything works fine: There is traffic on the 2 ports.
    When I disconnect one of the 2 ports, I can still ping outside with my PC client, but all my tcp sesssions goes down and I even cannot restart my session. The only way I found  is to do a "Disconnect / Reconnect"  on my  PC  wireless connection.
    Do you know this probleme ?
    Is it a way to avoid it ?
    Michel Misonne

    CSCth12513 LAG fail-over does not work on CT5508
    This bug is fixed in the special release available through TAC : 6.0.199.157 and 7.0.xxxx
    Hope this helps.
    Nicolas
    ===
    Dont' forget to rate answers that you find useful

  • Possible to setup something likes "protected port" on WLC 5508

    Hello,
    Let's say I have 3 APs, all connected to a WLC 5508
    Each AP has a computer that is connected to it, Computer A, B and C, all on the same Vlan with same SSID
    Is it possible to configure so
    A and B can not talk to each other but both can talk to C  ?
    Something like "protected port" feature in the switch world.
    Thanks

    Im looking for a solution for a WiFi network for our guests, where they dont need to talk to each other, and all need to talk to a wire internet gateway/router only.
    If you want to block guest SSID users from talking to each other then it's possible.  As Scott has pointed out, it's called "P2P Blocking Action".
    I do NOT recommend having guest and corporate share the same SSID.  I don't think it's best practice.

  • WLC 5508 - What is the use of service port.

    Hi,
    I am getting hard to understand use of service port in wlc 5508,
    Even after reading so much post and cisco note I am not understanig the use of (Even basic use) service port.
    As I understand service port should be access port and should be in diffrent vlan.
    Pleae help me to understand it in simple way....

    Hi Tarun,
    Like others mentioned it is used for Out of Band Management of a WLC. Many do not use this as it could leads to issues unless you properly configure it & put it onto two completely different supernets. Config guides highlighted those restrictions & below is one of them listed in 7.4 config guide
    Do not configure wired clients in the same VLAN or subnet of the service port of the controller on the network. If you configure wired clients on the same subnet or VLAN as the service port, it is not possible to access the management interface of the controller.
    In situations you can use it to get access by directly connecting a laptop to take configuration backup or restore configuration to a controller. In the below post I have used service port to take backup & restore the configuration to a WLC.
    http://mrncciew.com/2013/01/25/backup-restore-wlc-configs/
    HTH
    Rasika
    **** Pls rate all useful responses ****

  • Orion shows 3750 port speed changes - is it normal?

    Hi all,
      We use Orion for monitoring.  We recently started monitoring a workstation switch and find many occurances of port speed changes indicated.  Our workstation ports are configured with auto speed and duplex.  Is it normal that we are detecting speed changes on the ports?  Do workstations running XP automatically adjust their speed for traffic management or power save?  Perhaps something like speeds changing when PC goes to sleep mode but has wake on LAN enabled?  Is it possible that the MIB is misreporting?
      I realize that there are many different NIC vendors/drivers that might act differently.  Just wondering (in others experience) if it is somewhat normal or if there is anything on network I should be looking into as to why speeds are changing?  We plan to not monitor workstation ports (only uplinks) on the switch.. but before we do, I thought I would see if what we are detecting needs to be addressed?
      Here is an example from Orion of a speed changing.  Seems always off hours:
    6/1/2012 6:17:52 AM
    event
    WoRKSTATION-3750-CLUSTER - GigabitEthernet1/0/14 · 2nd Floor Patch#11 Interface Speed changed from 10000000 to 1000000000 bps
    6/1/2012 2:47:52 AM
    event
    WoRKSTATION-3750-CLUSTER - GigabitEthernet1/0/14 · 2nd Floor Patch#11 Interface Speed changed from 1000000000 to 10000000 bps
      Thanks in advance for any experienced feedback.
    Colin

    Ours does it all the time for some reason.  We presume it's due to the port negotiating speed during PC boot from 100mb to 1g, but never really followed up.

  • Deployment of WLC-5508 with 2702i-D have performance issue.

    Hi Team,
    We have centrally deployed WLC-5508 with 50 AP licence along with HA scenario. we have 3 locations.
    1- HQ. have 26 AP with POWINJ5.
    2- Branch location A- 8 AP with POWINJ5.
    3. Branch location B have 8 AP with POWINJ4.
    my exception is to achieve that  single SSID with dynamic VLAN from group police (NPS). MY HO have 26 AP and those are working in local mode.
    and branches are connected through flexconnect mode. and all are working with different-2 NPS. 
    Now i am facing a problem with this deployment are following.
    1- branch A have performance issue.
    2- HQ have performance issue.
    3- i don't want to go with dedicated NPS for every location. 
    In order to achieve this deployment i want only single SSID with primary and secondary NPS at my HQ with dynamic VLAN for respective departmental users vlans..
    above is my problem and concern. otherwise i am successfully achieving this solution with dedicated NPS with single group policy. but when i am going forward to achieve my expectation that time i am facing authentication issue at my HQ and sometimes am not able to get proper VLAN IPs. at my HQ. 
    kindly help me in that to understand where I am doing wrong things to achieve my expectation. 
    Thanks.
    Nalin    

    I am facing 2 different problems.
    1st issue- in existing setup we have throughput issue. (while downloading or uploading any data from the internet or Intranet,  that time wireless clients are facing slowness of the Speed. and same time when i am trying from LAN i am not facing any issue)
    2nd Issue- I want to achieve only single SSID with primary and secondary NPS (AD group is bind with vlan Attributes) with dynamic VLAN for respective departmental users.
    for Issue no 2 i have created SSID to achieve the single ssid parameter for every location. in order to achieve i have change all access points mode local to Flexconnect mode after that i have created AP groups location wise and then create flexconnect Groups where i have mapped all the vlan through AAA VLAN-ACL mapping. created interface group and mapped all the vlans in that group. 
    for more understanding please go through the below mentioned CLI view.
    Cisco Controller) >show wlan apgroups
    Total Number of AP Groups........................ 4
    Site Name........................................ GURGAON-AP-GROUP
    Site Description................................. GURGAON-AP-GROUP
    Venue Group Code................................. Unspecified
    Venue Type Code.................................. Unspecified
    NAS-identifier................................... Fractal-WLC1
    Client Traffic QinQ Enable....................... FALSE
    DHCPv4 QinQ Enable............................... FALSE
    AP Operating Class............................... Not-configured
    Capwap Prefer Mode............................... Not-configured
    RF Profile
    2.4 GHz band..................................... <none>
    5 GHz band....................................... <none>
    WLAN ID          Interface          Network Admission Control          Radio Pol                                                                                        icy
     3               gurgaon-interface    Disabled                          None
    --More-- or (q)uit
     4               gurgaon-guest        Disabled                          None
    *AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
    AP Name             Slots  AP Model             Ethernet MAC       Location          Port  Country  Priority
    GUR-AP-01            2     AIR-CAP2702I-D-K9    f4:4e:05:78:ae:e4  default location  1     IN       1
    GUR-AP-05            2     AIR-CAP2702I-D-K9    f4:4e:05:80:b5:18  default location  1     IN       1
    GUR-AP-03            2     AIR-CAP2702I-D-K9    bc:16:65:13:71:00  default location  1     IN       1
    GUR-AP-07            2     AIR-CAP2702I-D-K9    f4:4e:05:80:b3:f8  default location  1     IN       1
    GUR-AP-06            2     AIR-CAP2702I-D-K9    f4:4e:05:80:b3:e0  default location  1     IN       1
    GUR-AP-08            2     AIR-CAP2702I-D-K9    f4:4e:05:45:78:98  default location  1     IN       1
    GUR-AP-02            2     AIR-CAP2702I-D-K9    f4:4e:05:80:b3:2c  default location  1     IN       1
    GUR-AP-04            2     AIR-CAP2702I-D-K9    f4:4e:05:78:ae:64  default location  1     IN       1
    GUR-AP-09            2     AIR-CAP2702I-D-K9    f4:4e:05:80:b4:44  default location  1     IN       1
    Site Name........................................ MUMBAI-AP-GROUP
    Site Description................................. MUMBAI-AP-GROUP
    Venue Group Code................................. Unspecified
    Venue Type Code.................................. Unspecified
    --More-- or (q)uit
    NAS-identifier................................... Fractal-WLC1
    Client Traffic QinQ Enable....................... FALSE
    DHCPv4 QinQ Enable............................... FALSE
    AP Operating Class............................... Not-configured
    Capwap Prefer Mode............................... Not-configured
    RF Profile
    2.4 GHz band..................................... <none>
    5 GHz band....................................... <none>
    WLAN ID          Interface          Network Admission Control          Radio Policy
     1               group for mumbai     Disabled                          None
     2               guest wifi           Disabled                          None
    *AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
    AP Name             Slots  AP Model             Ethernet MAC       Location          Port  Country  Priority
    FAL-7-AP08           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:24:d8         7th Floor  1     IN       3
    --More-- or (q)uit
    FAL-7-AP10           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:18         7th Floor  1     IN       1
    FAL-7-AP14           2     AIR-CAP2702I-D-K9    f0:7f:06:bf:ad:e8         7th Floor  1     IN       1
    FAL-7-AP01           2     AIR-CAP2702I-D-K9    f0:7f:06:bf:b0:4c         7th Floor  1     IN       1
    FAL-7-AP07           2     AIR-CAP2702I-D-K9    f0:7f:06:30:92:bc         7th Floor  1     IN       1
    FAL-7-AP13           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:80         7th Floor  1     IN       1
    FAL-7-AP02           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:94         7th Floor  1     IN       1
    FAL-7-AP05           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:e8         7th Floor  1     IN       1
    FAL-7-AP12           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:f0         7th Floor  1     IN       3
    FAL-7-AP03           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:e4         7th Floor  1     IN       1
    FAL-7-AP06           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:84         7th Floor  1     IN       3
    FAL-7-AP04           2     AIR-CAP2702I-D-K9    f0:7f:06:bf:b0:14         7th Floor  1     IN       1
    FAL-7-AP09           2     AIR-CAP2702I-D-K9    f0:7f:06:92:b4:c8         7th Floor  1     IN       3
    FAL-7-AP11           2     AIR-CAP2702I-D-K9    f0:7f:06:30:93:08         7th Floor  1     IN       1
    Site Name........................................ MUMBAI-THIRD-FLOOR-AP
    Site Description................................. MUMBAI-THIRD-FLOOR-AP
    Venue Group Code................................. Unspecified
    Venue Type Code.................................. Unspecified
    NAS-identifier................................... Fractal-WLC1
    Client Traffic QinQ Enable....................... FALSE
    --More-- or (q)uit
    DHCPv4 QinQ Enable............................... FALSE
    AP Operating Class............................... Not-configured
    Capwap Prefer Mode............................... Not-configured
    RF Profile
    2.4 GHz band..................................... <none>
    5 GHz band....................................... <none>
    WLAN ID          Interface          Network Admission Control          Radio Policy
     1               group for mumbai     Disabled                          None
     2               guest wifi           Disabled                          None
    *AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
    AP Name             Slots  AP Model             Ethernet MAC       Location          Port  Country  Priority
    FAL-3-AP07           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:a4         3rd Floor  1     IN       3
    FAL-3-AP09           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:94         3rd Floor  1     IN       3
    FAL-3-AP11           2     AIR-CAP2702I-D-K9    f4:0f:1b:73:00:74  3rd Floor- Eurek  1     IN       3
    FAL-3-AP06           2     AIR-CAP2702I-D-K9    f0:7f:06:bf:ae:d0         3rd Floor  1     IN       3
    --More-- or (q)uit
    FAL-3-AP10           2     AIR-CAP2702I-D-K9    f0:7f:06:92:b5:88         3rd Floor  1     IN       3
    FAL-3-AP08           2     AIR-CAP2702I-D-K9    f0:7f:06:92:b4:9c         3rd Floor  1     IN       3
    FAL-3-AP03           2     AIR-CAP2702I-D-K9    f0:7f:06:bf:af:a0         3rd Floor  1     IN       1
    FAL-3-AP12           2     AIR-CAP2702I-D-K9    f0:7f:06:92:b3:fc  3rd Floor- Eurek  1     IN       3
    FAL-3-AP02           2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:28         3rd Floor  1     IN       3
    FAL-3-AP01           2     AIR-CAP2702I-D-K9    f0:7f:06:92:b4:f4         3rd Floor  1     IN       3
    FAL-3-AP04           2     AIR-CAP2702I-D-K9    f0:7f:06:30:92:8c         3rd Floor  1     IN       2
    FAL-3-AP05           2     AIR-CAP2702I-D-K9    f0:7f:06:30:91:f4         3rd Floor  1     IN       3
    Site Name........................................ RAHEJA-AP-GROUP
    Site Description................................. RAHEJA-AP-GROUP
    Venue Group Code................................. Unspecified
    Venue Type Code.................................. Unspecified
    NAS-identifier................................... Fractal-WLC1
    Client Traffic QinQ Enable....................... FALSE
    DHCPv4 QinQ Enable............................... FALSE
    AP Operating Class............................... Not-configured
    Capwap Prefer Mode............................... Not-configured
    RF Profile
    --More-- or (q)uit
    2.4 GHz band..................................... <none>
    5 GHz band....................................... <none>
    WLAN ID          Interface          Network Admission Control          Radio Policy
     5               raheja-interface     Disabled                          None
     2               raheja-guest         Disabled                          None
    *AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
    AP Name             Slots  AP Model             Ethernet MAC       Location          Port  Country  Priority
    FAL-RAHEJA-AP04      2     AIR-CAP2702I-D-K9    f0:7f:06:8d:24:1c  Near Meeting Roo  1     IN       3
    FAL-RAHEJA-AP02      2     AIR-CAP2702I-D-K9    f0:7f:06:8d:37:3c   Confrennce Room  1     IN       3
    FAL-RAHEJA-AP03      2     AIR-CAP2702I-D-K9    f0:7f:06:30:93:48  Near Confrence R  1     IN       3
    FAL-RAHEJA-AP05      2     AIR-CAP2702I-D-K9    f0:7f:06:bf:ae:c0  Near Meeting Roo  1     IN       3
    FAL-RAHEJA-AP06      2     AIR-CAP2702I-D-K9    f0:7f:06:92:b3:a0  Near Server Room  1     IN       3
    FAL-RAHEJA-AP01      2     AIR-CAP2702I-D-K9    f0:7f:06:92:b3:20    Reception Area  1     IN       3
    FAL-RAHEJA-AP08      2     AIR-CAP2702I-D-K9    f0:7f:06:8d:25:68  USER BAY ROAD si  1     IN       1
    FAL-RAHEJA-AP09      2     AIR-CAP2702I-D-K9    f0:7f:06:92:b4:d4     Training Room  1     IN       1
    --More-- or (q)uit
    Site Name........................................ default-group
    Site Description................................. <none>
    NAS-identifier................................... Fractal-WLC1
    Client Traffic QinQ Enable....................... FALSE
    DHCPv4 QinQ Enable............................... FALSE
    AP Operating Class............................... Not-configured
    Capwap Prefer Mode............................... Not-configured
    RF Profile
    2.4 GHz band..................................... <none>
    5 GHz band....................................... <none>
    WLAN ID          Interface          Network Admission Control          Radio Policy
     1               group for mumbai     Disabled                          None
     2               guest wifi           Disabled                          None
     3               gurgaon-interface    Disabled                          None
     4               gurgaon-guest        Disabled                          None
     5               raheja-interface     Disabled                          None
     6               test                 Disabled                          None
    Cisco Controller) >show flexconnect group summary
    FlexConnect Group Summary: Count: 4
    Group Name                # Aps
    Gurgaon-AP                         9
    HQ-3RD-FLR-AP-GROUP                        12
    HQ-7THFLR-AP-GROUP                         14
    Raheja-AP-Group                            8
    (Cisco Controller) >show flexconnect group detail Gurgaon-AP
    Number of AP's in Group: 9
    bc:16:65:13:71:00    GUR-AP-03     Joined    Flexconnect
    f4:4e:05:45:78:98    GUR-AP-08     Joined    Flexconnect
    f4:4e:05:78:ae:64    GUR-AP-04     Joined    Flexconnect
    f4:4e:05:78:ae:e4    GUR-AP-01     Joined    Flexconnect
    f4:4e:05:80:b3:2c    GUR-AP-02     Joined    Flexconnect
    f4:4e:05:80:b3:e0    GUR-AP-06     Joined    Flexconnect
    f4:4e:05:80:b3:f8    GUR-AP-07     Joined    Flexconnect
    f4:4e:05:80:b4:44    GUR-AP-09     Joined    Flexconnect
    f4:4e:05:80:b5:18    GUR-AP-05     Joined    Flexconnect
    Efficient AP Image Upgrade ..... Disabled
    Master-AP-Mac     Master-AP-Name                    Model      Manual
    Group Radius Servers Settings:
    Type           Server Address    Port
                                             Primary       Unconfigured      Unconfigured
                                                                                          Secondary     Unconfigured      Unconfigured
    --More-- or (q)uit
    Group Radius AP Settings:
    AP RADIUS server............ Disabled
    EAP-FAST Auth............... Disabled
    LEAP Auth................... Disabled
    EAP-TLS Auth................ Disabled
    EAP-TLS CERT Download....... Disabled
    PEAP Auth................... Disabled
    Server Key Auto Generated... No
    Server Key..................     <hidden>
    Authority ID................ 436973636f0000000000000000000000
    Authority Info.............. Cisco A_ID
    PAC Timeout................. 0
    Multicast on Overridden interface config: Disabled
    DHCP Broadcast Overridden interface config: Disabled
    Number of User's in Group: 0
    Vlan :........................................... 203
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 205
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 204
    --More-- or (q)uit
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 206
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 207
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 208
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 209
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 210
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 211
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 212
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    --More-- or (q)uit
    Vlan :........................................... 216
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 217
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Vlan :........................................... 218
            Ingress ACL :................................... None
            Egress ACL :.................................... None
    Group-Specific FlexConnect Wlan-Vlan Mapping:
    WLAN ID     Vlan ID
    WLAN ID   SSID                            Central-Dhcp  Dns-Override  Nat-Pat
    (Cisco Controller) >
    (Cisco Controller) >show wlan summary
    Number of WLANs.................................. 6
    WLAN ID  WLAN Profile Name / SSID               Status    Interface Name        PMIPv6 Mobility
    1        FRACTAL-EMP-MUMBAI / FRACTAL           Enabled   group for mumbai      none
    2        FRACTAL-GUEST / FRACTAL-GUEST          Enabled   guest wifi            none
    3        FRACTAL-EMP-GURGAON / FRACTAL-GURGAON  Enabled   gurgaon-interface     none
    4        GURGAON-GUEST / FRACTAL-GUEST-GURGAON  Enabled   gurgaon-guest         none
    5        RAHEJA-EMP-WIRELESS / FRACTAL-R        Enabled   raheja-interface      none
    6        TEST-SSID / TEST-SSID                  Enabled   test                  none
    hope this will give you proper understanding.  

  • AIR-CAP1602I-E-K9 Not Talking to WLC 5508

    hi all,
    can't seem to get my APs to talk to WLC 5508.
    can someone advise which WLC firmware to use and where can i get/download (link pls).
    currently WLC is running 6.0.199.4.
    Mar  1 00:00:47.839: %CDP_PD-4-POWER_OK: All radios disabled - NEGOTIATED inlin
    e power source
    *Mar  1 00:00:53.931: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
    not have an Ip !!
    *Mar  1 00:00:55.963: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP addre
    ss 172.28.159.15, mask 255.255.255.192, hostname APfc99.47a3.4d22
    Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
    *Mar  1 00:01:06.899: %CAPWAP-3-ERRORLOG: Did not get log server settings from D
    HCP.
    *Mar  1 00:01:15.899: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
    LER
    *Mar  1 00:01:15.899: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_f8
    :72:64'running version 6.0.199.4 is rejected.    <<<<
    APfc99.47a3.4d22>sh ve
    Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
    SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2012 by Cisco Systems, Inc.
    Compiled Tue 11-Dec-12 04:52 by prod_rel_team
    ROM: Bootstrap program is C1600 boot loader
    BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFT
    WARE (fc1)
    APfc99.47a3.4d22 uptime is 11 minutes
    System returned to ROM by power-on
    System image file is "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"
    Last reload reason:
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP1602I-E-K9    (PowerPC) processor (revision B0) with 98294K/32768K
    bytes of memory.
    Processor board ID FGL1726W6DQ
    PowerPC CPU at 533Mhz, revision number 0x2151
    Last reset from power-on
    LWAPP image version 7.4.1.37
    1 Gigabit Ethernet interface
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: FC:99:47:A3:4D:22
    Part Number                          : 73-14671-04
    PCA Assembly Number                  : 000-00000-00
    PCA Revision Number                  :
    PCB Serial Number                    : FOC17182J4J
    Top Assembly Part Number             : 800-38552-01
    Top Assembly Serial Number           : FGL1726W6DQ
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP1602I-E-K9
    Configuration register is 0xF

    Hi,
    Date and time is ok on the WLC,
    I configured Accept Self Signed Certificate (SSC) under Security / AP policy, once done the WLC recognized the AP, but output from the console of the AP  power cycle the access point is:
    IOS Bootloader - Starting system.
    FLASH CHIP: Micronix MX25L256_35F
    Xmodem file system is available.
    flashfs[0]: 5 files, 2 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31936000
    flashfs[0]: Bytes used: 6551040
    flashfs[0]: Bytes available: 25384960
    flashfs[0]: flashfs fsck took 9 seconds.
    Reading cookie from SEEPROM
    Base Ethernet MAC address: 4c:00:82:9a:47:a3
    ************* loopback_mode = 0
    Loading "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"...####################
    File "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx" uncompressed and installed, entr
    y point: 0x100000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
    SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2012 by Cisco Systems, Inc.
    Compiled Tue 11-Dec-12 04:52 by prod_rel_team
    Initializing flashfs...
    FLASH CHIP: Micronix MX25L256_35F
    flashfs[2]: 5 files, 2 directories
    flashfs[2]: 0 orphaned files, 0 orphaned directories
    flashfs[2]: Total bytes: 31808000
    flashfs[2]: Bytes used: 6551040
    flashfs[2]: Bytes available: 25256960
    flashfs[2]: flashfs fsck took 9 seconds.
    flashfs[2]: Initialization complete.
    flashfs[3]: 0 files, 1 directories
    flashfs[3]: 0 orphaned files, 0 orphaned directories
    flashfs[3]: Total bytes: 11999232
    flashfs[3]: Bytes used: 1024
    flashfs[3]: Bytes available: 11998208
    flashfs[3]: flashfs fsck took 1 seconds.
    flashfs[3]: Initialization complete....done Initializing flashfs.
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    memory validate-checksum 30
    ^
    % Invalid input detected at '^' marker.
    no ip http server
           ^
    % Invalid input detected at '^' marker.
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    login authentication default
      ^
    % Invalid input detected at '^' marker.
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    Warning:  the compile-time code checksum does not appear to be present.
    cisco AIR-CAP1602I-N-K9    (PowerPC) processor (revision B0) with 98294K/32768K
    bytes of memory.
    Processor board ID FGL1730S57A
    PowerPC CPU at 533Mhz, revision number 0x2151
    Last reset from power-on
    LWAPP image version 7.4.1.37
    1 Gigabit Ethernet interface
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 4C:00:82:9A:47:A3
    Part Number                          : 73-14671-04
    PCA Assembly Number                  : 000-00000-00
    PCA Revision Number                  :
    PCB Serial Number                    : FOC17284HL9
    Top Assembly Part Number             : 800-38552-01
    Top Assembly Serial Number           : FGL1730S57A
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP1602I-N-K9
    % Please define a domain-name first.
    logging facility kern
            ^
    % Invalid input detected at '^' marker.
    logging trap emergencies
            ^
    % Invalid input detected at '^' marker.
    Press RETURN to get started!
    *Mar  1 00:00:12.451: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
    itialising Cfg
    *Mar  1 00:00:13.683: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state
    to up
    *Mar  1 00:00:14.687: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
    ernet0, changed state to up
    *Mar  1 00:00:15.123: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
    SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2012 by Cisco Systems, Inc.
    Compiled Tue 11-Dec-12 04:52 by prod_rel_team
    *Mar  1 00:00:15.151: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
    itialising Cfg
    *Mar  1 00:00:15.151: %CAPWAP-3-ERRORLOG: Failed to load configuration from flas
    h. Resetting to default config
    *Mar  1 00:00:16.195: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
    ged state to uplwapp_crypto_init: MIC Present and Parsed Successfully
    no bridge-group 1 source-learning
                       ^
    % Invalid input detected at '^' marker.
    %Default route without gateway, if not a point-to-point interface, may impact pe
    rformance
    *Mar  1 00:00:48.695: %CDP_PD-4-POWER_OK: All radios disabled - INJECTOR_CONFIGU
    RED_ON_SOURCE inline power source
    *Mar  1 00:00:48.923: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP addre
    ss 10.2.3.100, mask 255.255.255.0, hostname AP4c00.829a.47a3
    Translating "CISCO-CAPWAP-CONTROLLER.campeche.ecosur.mx"...domain server (10.2.3
    .10) [OK]
    *Mar  1 00:00:59.915: %CAPWAP-3-ERRORLOG: Did not get log server settings from D
    HCP.
    *Mar  1 00:00:59.919: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
    not established. A0203E6, 147E, A020364, A47B, 0
    *Mar  1 00:01:09.915: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Jan 29 09:33:18.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
    p: 10.2.3.230 peer_port: 5246
    *Jan 29 09:33:18.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
    peer_ip: 10.2.3.230 peer_port: 5246
    *Jan 29 09:33:18.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
    *Jan 29 09:33:23.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
    logging facility kern
            ^
    % Invalid input detected at '^' marker.
    logging trap emergencies
            ^
    % Invalid input detected at '^' marker.
    *Jan 29 09:34:17.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.
    2.3.230:5246
    *Jan 29 09:34:17.999: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led sta
    te 255
    *Jan 29 09:34:17.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
    itialising Cfg
    *Jan 29 09:34:17.999: %CAPWAP-3-ERRORLOG: Failed to load configuration from flas
    h. Resetting to default config
    *Jan 29 09:34:28.015: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Jan 29 09:34:28.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
    p: 10.2.3.230 peer_port: 5246
    *Jan 29 09:34:28.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
    peer_ip: 10.2.3.230 peer_port: 5246
    *Jan 29 09:34:28.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
    *Jan 29 09:34:33.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
    and debug command output enable CAPWAP events
    (Cisco Controller) >debug capwap events enable
    (Cisco Controller) >*spamApTask7: Jan 29 03:39:08.092: acDtlsPlumbControlPlaneKeys: lrad:10.2.3.100(42107) mwar:10.2.3.230(5246)
    *spamApTask7: Jan 29 03:39:08.093: 4c:00:82:9a:47:a0 DTLS keys for Control Plane deleted successfully for AP 10.2.3.100
    *spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 DTLS connection closed event receivedserver (10.2.3.230/5246) client (10.2.3.100/42107)
    *spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 Entry exists for AP (10.2.3.100/42107)
    *spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 No AP entry exist in temporary database for 10.2.3.100:42107
    *spamApTask7: Jan 29 03:39:08.104: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
    *spamApTask7: Jan 29 03:39:08.104: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
    *spamApTask7: Jan 29 03:39:08.104: apModel:
    *spamApTask7: Jan 29 03:39:08.104: apType = 38 apModel:
    *spamApTask0: Jan 29 03:39:08.105: 4c:00:82:9a:47:a3 Received LWAPP DISCOVERY REQUEST to 6c:41:6a:5f:95:2f on port '13'
    *spamApTask0: Jan 29 03:39:08.105: 4c:00:82:9a:47:a3 Discarding discovery request in LWAPP from AP supporting CAPWAP
    *spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
    *spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
    *spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
    *spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
    *spamApTask7: Jan 29 03:39:08.105: apModel:
    *spamApTask7: Jan 29 03:39:08.105: apType = 38 apModel:
    *spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
    *spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
    *spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
    *spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
    *spamApTask7: Jan 29 03:39:08.105: apModel:
    *spamApTask7: Jan 29 03:39:08.105: apType = 38 apModel:
    *spamApTask7: Jan 29 03:39:08.106: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
    (Cisco Controller) >*spamApTask7: Jan 29 03:39:08.106: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
    *spamApTask7: Jan 29 03:39:18.104: 4c:00:82:9a:47:a3 DTLS connection not found, creating new connection for 10:2:3:100 (42107) 10:2:3:230 (5246)
    *spamApTask7: Jan 29 03:39:18.638: acDtlsPlumbControlPlaneKeys: lrad:10.2.3.100(42107) mwar:10.2.3.230(5246)
    *spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Allocated index from main list, Index: 397
    *spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Using CipherSuite AES128-SHA
    *spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 DTLS keys for Control Plane are plumbed successfully for AP 10.2.3.100. Index 398
    *spamApTask6: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 DTLS Session established server (10.2.3.230:5246), client (10.2.3.100:42107)
    *spamApTask6: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Starting wait join timer for AP: 10.2.3.100:42107
    *spamApTask7: Jan 29 03:39:23.636: 4c:00:82:9a:47:a0 Join Request from 10.2.3.100:42107
    *spamApTask7: Jan 29 03:39:23.636: 4c:00:82:9a:47:a3 Deleting AP entry 10.2.3.100:42107 from temporary database.
    *spamApTask7: Jan 29 03:39:23.637: 4c:00:82:9a:47:a0 MIC AP is not allowed to join by config
    *spamApTask7: Jan 29 03:39:23.637: 4c:00:82:9a:47:a0 Join Request failed!

  • Cisco ISE 1.2 & Cisco WLC 5508 v7.6

    Hi all,
    we are planning to upgrade our WLC to 7.6 to fix a bug with FlexConnect Client ACLs but I have just seen on the Cisco ISE Compatibility table that the it only recommends up to v7.5 of the WLC 5508...
    Cisco have told me to steer clear of 7.5 as it is in a defferred status, so does anyone know, or have running in a lab or production, ISE1.2 with a 5508 WLC v7.6 NAD ?
    I would much rather know of any issues people are experiencing before hand than to have to go through a software upgrade and then rollback.
    Thanks all
    Mario De Rosa

    Hi Neno,
    right I have this almost working now.
    I have simplified the setup. I am not going to do any client provisioning at the moment.
    So I can connect to the corporate SSID using EAP-TLS and I can successfully push the branch data VLAN upon successful authorisation.
    Now I am trying to introduce the posture element & per user ACLs.
    I have defined the redirect ACL & Flex ACL on the vWLC however the NAC agent will not pop-up. The client is in the right VLAN and the redirect ACL seems to be getting applied as the client does get an IP through DHCP. However, the client cannot ping the ISE or access the guest portal when I open the browser.
    DNS resolution seems to be working fine.
    VLAN220 is my datacentre VLAN which the Management Interface on the controller is plugged in to.
    VLAN10 is the branch DATA VLAN.
    below is some output to give you some more details...
    (Cisco Controller) >show client detail 00:24:d6:97:b3:be
    Client MAC Address............................... 00:24:d6:97:b3:be
    Client Username ................................. [email protected]
    AP MAC Address................................... 18:33:9d:f0:21:80
    AP Name.......................................... test-flex-ap
    AP radio slot Id................................. 0
    Client State..................................... Associated
    Client NAC OOB State............................. Access
    Wireless LAN Id.................................. 2
    Hotspot (802.11u)................................ Not Supported
    BSSID............................................ 18:33:9d:f0:21:81
    Connected For ................................... 128 secs
    Channel.......................................... 6
    IP Address....................................... 10.130.130.120
    Gateway Address.................................. 10.130.130.1
    Netmask.......................................... 255.255.255.0
    IPv6 Address..................................... fe80::f524:1910:69f0:9482
    Association Id................................... 1
    Authentication Algorithm......................... Open System
    Reason Code...................................... 1
    Status Code...................................... 0
    Client CCX version............................... 4
    Client E2E version............................... 1
    --More-- or (q)uit
    Re-Authentication Timeout........................ 1651
    QoS Level........................................ Silver
    Avg data Rate.................................... 0
    Burst data Rate.................................. 0
    Avg Real time data Rate.......................... 0
    Burst Real Time data Rate........................ 0
    802.1P Priority Tag.............................. disabled
    CTS Security Group Tag........................... Not Applicable
    KTS CAC Capability............................... No
    WMM Support...................................... Enabled
      APSD ACs.......................................  BK  BE  VI  VO
    Power Save....................................... OFF
    Current Rate..................................... m13
    Supported Rates.................................. 1.0,2.0,5.5,11.0,6.0,9.0,
        ............................................. 12.0,18.0,24.0,36.0,48.0,
        ............................................. 54.0
    Mobility State................................... Local
    Mobility Move Count.............................. 0
    Security Policy Completed........................ No
    Policy Manager State............................. POSTURE_REQD
    Policy Manager Rule Created...................... Yes
    AAA Override ACL Name............................ POSTURE_REDIRECT_ACL
    AAA Override ACL Applied Status.................. Yes
    --More-- or (q)uit
    AAA Override Flex ACL Name....................... POSTURE_REDIRECT_ACL
    AAA Override Flex ACL Applied Status............. Yes
    AAA URL redirect................................. https://pdc-ise-man01.kier.group:8443/guestportal/gateway?sessionId=c8dc800a00000005b3e7e953&action=cpp
    Audit Session ID................................. c8dc800a00000005b3e7e953
    AAA Role Type.................................... none
    Local Policy Applied............................. none
    IPv4 ACL Name.................................... none
    FlexConnect ACL Applied Status................... Yes
    IPv4 ACL Applied Status.......................... Unavailable
    IPv6 ACL Name.................................... none
    IPv6 ACL Applied Status.......................... Unavailable
    Layer2 ACL Name.................................. none
    Layer2 ACL Applied Status........................ Unavailable
    mDNS Status...................................... Disabled
    mDNS Profile Name................................ none
    No. of mDNS Services Advertised.................. 0
    Policy Type...................................... WPA2
    Authentication Key Management.................... 802.1x
    Encryption Cipher................................ CCMP (AES)
    Protected Management Frame ...................... No
    Management Frame Protection...................... No
    EAP Type......................................... EAP-TLS
    FlexConnect Data Switching....................... Local
    --More-- or (q)uit
    FlexConnect Dhcp Status.......................... Local
    FlexConnect Vlan Based Central Switching......... No
    FlexConnect Authentication....................... Central
    Quarantine VLAN.................................. 0
    Access VLAN...................................... 220
    Client Capabilities:
          CF Pollable................................ Not implemented
          CF Poll Request............................ Not implemented
          Short Preamble............................. Implemented
          PBCC....................................... Not implemented
          Channel Agility............................ Not implemented
          Listen Interval............................ 10
          Fast BSS Transition........................ Not implemented
    Client Wifi Direct Capabilities:
          WFD capable................................ No
          Manged WFD capable......................... No
          Cross Connection Capable................... No
          Support Concurrent Operation............... No
    Fast BSS Transition Details:
    Client Statistics:
          Number of Bytes Received................... 33698
          Number of Bytes Sent....................... 19397
          Total Number of Bytes Sent................. 19397
    --More-- or (q)uit
          Total Number of Bytes Recv................. 33698
          Number of Bytes Sent (last 90s)............ 19397
          Number of Bytes Recv (last 90s)............ 33698
          Number of Packets Received................. 283
          Number of Packets Sent..................... 147
          Number of Interim-Update Sent.............. 0
          Number of EAP Id Request Msg Timeouts...... 0
          Number of EAP Id Request Msg Failures...... 0
          Number of EAP Request Msg Timeouts......... 0
          Number of EAP Request Msg Failures......... 0
          Number of EAP Key Msg Timeouts............. 0
          Number of EAP Key Msg Failures............. 0
          Number of Data Retries..................... 53
          Number of RTS Retries...................... 0
          Number of Duplicate Received Packets....... 2
          Number of Decrypt Failed Packets........... 0
          Number of Mic Failured Packets............. 0
          Number of Mic Missing Packets.............. 0
          Number of RA Packets Dropped............... 0
          Number of Policy Errors.................... 0
          Radio Signal Strength Indicator............ -42 dBm
          Signal to Noise Ratio...................... 41 dB
    Client Rate Limiting Statistics:
    --More-- or (q)uit
          Number of Data Packets Recieved............ 0
          Number of Data Rx Packets Dropped.......... 0
          Number of Data Bytes Recieved.............. 0
          Number of Data Rx Bytes Dropped............ 0
          Number of Realtime Packets Recieved........ 0
          Number of Realtime Rx Packets Dropped...... 0
          Number of Realtime Bytes Recieved.......... 0
          Number of Realtime Rx Bytes Dropped........ 0
          Number of Data Packets Sent................ 0
          Number of Data Tx Packets Dropped.......... 0
          Number of Data Bytes Sent.................. 0
          Number of Data Tx Bytes Dropped............ 0
          Number of Realtime Packets Sent............ 0
          Number of Realtime Tx Packets Dropped...... 0
          Number of Realtime Bytes Sent.............. 0
          Number of Realtime Tx Bytes Dropped........ 0
    Nearby AP Statistics:
          test-flex-ap(slot 0)
            antenna0: 14 secs ago.................... -51 dBm
            antenna1: 14 secs ago.................... -37 dBm
          test-flex-ap(slot 1)
            antenna0: 14 secs ago.................... -51 dBm
            antenna1: 14 secs ago.................... -54 dBm
    --More-- or (q)uit
    DNS Server details:
          DNS server IP ............................. 10.0.17.31
          DNS server IP ............................. 10.0.17.43
    Assisted Roaming Prediction List details:
     Client Dhcp Required:     False
    Allowed (URL)IP Addresses
    (Cisco Controller) >
    (Cisco Controller) >show wlan 2
    WLAN Identifier.................................. 2
    Profile Name..................................... Demo1x
    Network Name (SSID).............................. Demo1x
    Status........................................... Enabled
    MAC Filtering.................................... Disabled
    Broadcast SSID................................... Enabled
    AAA Policy Override.............................. Enabled
    Network Admission Control
    Client Profiling Status
        Radius Profiling ............................ Disabled
         DHCP ....................................... Disabled
         HTTP ....................................... Disabled
        Local Profiling ............................. Disabled
         DHCP ....................................... Disabled
         HTTP ....................................... Disabled
      Radius-NAC State............................... Enabled
      SNMP-NAC State................................. Disabled
      Quarantine VLAN................................ 0
    Maximum number of Associated Clients............. 0
    Maximum number of Clients per AP Radio........... 200
    --More-- or (q)uit
    Number of Active Clients......................... 1
    Exclusionlist Timeout............................ 60 seconds
    Session Timeout.................................. 1800 seconds
    User Idle Timeout................................ Disabled
    Sleep Client..................................... disable
    Sleep Client Timeout............................. 12 hours
    User Idle Threshold.............................. 0 Bytes
    NAS-identifier................................... mario-test-flex-vwlc
    CHD per WLAN..................................... Enabled
    Webauth DHCP exclusion........................... Disabled
    Interface........................................ management
    Multicast Interface.............................. Not Configured
    WLAN IPv4 ACL.................................... unconfigured
    WLAN IPv6 ACL.................................... unconfigured
    WLAN Layer2 ACL.................................. unconfigured
    mDNS Status...................................... Disabled
    mDNS Profile Name................................ unconfigured
    DHCP Server...................................... Default
    DHCP Address Assignment Required................. Disabled
    Static IP client tunneling....................... Disabled
    Quality of Service............................... Silver
    Per-SSID Rate Limits............................. Upstream      Downstream
    Average Data Rate................................   0             0
    --More-- or (q)uit
    Average Realtime Data Rate.......................   0             0
    Burst Data Rate..................................   0             0
    Burst Realtime Data Rate.........................   0             0
    Per-Client Rate Limits........................... Upstream      Downstream
    Average Data Rate................................   0             0
    Average Realtime Data Rate.......................   0             0
    Burst Data Rate..................................   0             0
    Burst Realtime Data Rate.........................   0             0
    Scan Defer Priority.............................. 4,5,6
    Scan Defer Time.................................. 100 milliseconds
    WMM.............................................. Allowed
    WMM UAPSD Compliant Client Support............... Disabled
    Media Stream Multicast-direct.................... Disabled
    CCX - AironetIe Support.......................... Enabled
    CCX - Gratuitous ProbeResponse (GPR)............. Disabled
    CCX - Diagnostics Channel Capability............. Disabled
    Dot11-Phone Mode (7920).......................... Disabled
    Wired Protocol................................... None
    Passive Client Feature........................... Disabled
    Peer-to-Peer Blocking Action..................... Disabled
    Radio Policy..................................... All
    DTIM period for 802.11a radio.................... 1
    DTIM period for 802.11b radio.................... 1
    --More-- or (q)uit
    Radius Servers
       Authentication................................ 10.0.16.111 1812
       Accounting.................................... 10.131.16.111 1813
          Interim Update............................. Disabled
          Framed IPv6 Acct AVP ...................... Prefix
       Dynamic Interface............................. Disabled
       Dynamic Interface Priority.................... wlan
    Local EAP Authentication......................... Disabled
    Security
       802.11 Authentication:........................ Open System
       FT Support.................................... Disabled
       Static WEP Keys............................... Disabled
       802.1X........................................ Disabled
       Wi-Fi Protected Access (WPA/WPA2)............. Enabled
          WPA (SSN IE)............................... Disabled
          WPA2 (RSN IE).............................. Enabled
             TKIP Cipher............................. Disabled
             AES Cipher.............................. Enabled
                                                                   Auth Key Management
             802.1x.................................. Enabled
             PSK..................................... Disabled
             CCKM.................................... Disabled
    --More-- or (q)uit
             FT-1X(802.11r).......................... Disabled
             FT-PSK(802.11r)......................... Disabled
             PMF-1X(802.11w)......................... Disabled
             PMF-PSK(802.11w)........................ Disabled
          FT Reassociation Timeout................... 20
          FT Over-The-DS mode........................ Enabled
          GTK Randomization.......................... Disabled
          SKC Cache Support.......................... Disabled
          CCKM TSF Tolerance......................... 1000
       WAPI.......................................... Disabled
       Wi-Fi Direct policy configured................ Disabled
       EAP-Passthrough............................... Disabled
       CKIP ......................................... Disabled
       Web Based Authentication...................... Disabled
       Web-Passthrough............................... Disabled
       Conditional Web Redirect...................... Disabled
       Splash-Page Web Redirect...................... Disabled
       Auto Anchor................................... Disabled
       FlexConnect Local Switching................... Enabled
       flexconnect Central Dhcp Flag................. Disabled
       flexconnect nat-pat Flag...................... Disabled
       flexconnect Dns Override Flag................. Disabled
       flexconnect PPPoE pass-through................ Disabled
    --More-- or (q)uit
       flexconnect local-switching IP-source-guar.... Disabled
       FlexConnect Vlan based Central Switching ..... Disabled
       FlexConnect Local Authentication.............. Disabled
       FlexConnect Learn IP Address.................. Enabled
       Client MFP.................................... Optional
       PMF........................................... Disabled
       PMF Association Comeback Time................. 1
       PMF SA Query RetryTimeout..................... 200
       Tkip MIC Countermeasure Hold-down Timer....... 60
       Eap-params.................................... Disabled
    AVC Visibilty.................................... Disabled
    AVC Profile Name................................. None
    Flow Monitor Name................................ None
    Split Tunnel (Printers).......................... Disabled
    Call Snooping.................................... Disabled
    Roamed Call Re-Anchor Policy..................... Disabled
    SIP CAC Fail Send-486-Busy Policy................ Disabled
    SIP CAC Fail Send Dis-Association Policy......... Disabled
    KTS based CAC Policy............................. Disabled
    Assisted Roaming Prediction Optimization......... Disabled
    802.11k Neighbor List............................ Disabled
    802.11k Neighbor List Dual Band.................. Disabled
    Band Select...................................... Disabled
    --More-- or (q)uit
    Load Balancing................................... Disabled
    Multicast Buffer................................. Disabled
     Mobility Anchor List
     WLAN ID     IP Address            Status
    802.11u........................................ Disabled
    MSAP Services.................................. Disabled
    Local Policy
    Priority  Policy Name
    (Cisco Controller) >
    when debugging the client during redirect, this is the output and I cannot spot anything wrong here...
    (Cisco Controller) >*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Adding mobile on LWAPP AP 18:33:9d:f0:21:80(1) 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Association received from mobile on BSSID 18:33:9d:f0:21:8e
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Global 200 Clients are allowed to AP radio
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Max Client Trap Threshold: 0  cur: 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Re-applying interface policy for client 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be In processSsidIE:4850 setting Central switched to FALSE
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying site-specific Local Bridging override for station 00:24:d6:97:b3:be - vapId 2, site 'default-group', interface 'management'
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Local Bridging Interface Policy for station 00:24:d6:97:b3:be - vlan 220, interface id 0, interface 'management'
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE  statusCode is 0 and status is 0 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be suppRates  statusCode is 0 and gotSuppRatesElement is 1 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Processing RSN IE type 48, length 22 for mobile 00:24:d6:97:b3:be
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Received RSN IE with 0 PMKIDs from mobile 00:24:d6:97:b3:be
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Updating AID for REAP AP Client 18:33:9d:f0:21:80 - AID ===> 1
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Central switch is FALSE
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name: 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfMsAssoStateInc
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Idle to Associated
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2:session timeout forstation 00:24:d6:97:b3:be - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is  0 
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Stopping deletion of Mobile Station: (callerId: 48)
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Sending Assoc Response to station on BSSID 18:33:9d:f0:21:8e (status 0) ApVapId 2 Slot 1
    *apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfProcessAssocReq (apf_80211.c:8294) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Associated to Associated
    *spamApTask6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sent 1x initiate message to multi thread task for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be EAP-PARAM Debug - eap-params for Wlan-Id :2 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Connecting state
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sending EAP-Request/Identity to mobile 00:24:d6:97:b3:be (EAP Id 1)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received Identity Response (count=1) from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Resetting reauth count 1 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be EAP State update from Connecting to Authenticating for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticating state
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=214) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be WARNING: updated EAP-Identifier 1 ===> 214 for STA 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 214)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Allocating EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 214, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=215) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 215)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 215, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=216) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 216)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 216, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=217) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 217)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 217, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=218) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 218)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 218, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=219) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 219)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 219, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=220) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 220)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 220, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=221) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 221)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 221, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=222) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 222)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 222, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=223) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 223)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 223, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=224) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 224)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 224, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=225) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 225)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 225, EAP Type 13)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Processing Access-Accept for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 acl from 255 to 255
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 Flex acl from 65535 to 65535
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created for mobile, length = 253 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created in mscb for mobile, length = 253 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 220
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Re-applying interface policy for client 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 1 on mobile 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Inserting AAA Override struct for mobile
        MAC: 00:24:d6:97:b3:be, source 4
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting re-auth timeout to 1800 seconds, got from WLAN config.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Creating a PKC PMKID Cache entry for station 00:24:d6:97:b3:be (RSN 2)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting MSCB PMK Cache Entry 0 for station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Adding BSSID 18:33:9d:f0:21:8e to PMKID cache at index 0 for station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: New PMKID: (16)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410:      [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Disabling re-auth since PMK lifetime can take care of same.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Client in Posture Reqd state. PMK cache not updated.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAP-Success to mobile 00:24:d6:97:b3:be (EAP Id 225)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Freeing AAACB from Dot1xCB as AAA auth is done for  mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be EAPOL Header: 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00000000: 02 03 5f 00                                       .._.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410:      [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Starting key exchange to mobile 00:24:d6:97:b3:be, data packets will be dropped
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Entering Backend Auth Success state (id=225) for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Received Auth Success while in Authenticating state for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticated state
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-key in PTK_START state (message 2) from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be PMK: Sending cache add
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be EAPOL Header: 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00000000: 02 03 5f 00                                       .._.
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
       state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be  mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Freeing EAP Retransmit Bufer for mobile 00:24:d6:97:b3:be
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be apfMs1xStateInc
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central switch is FALSE
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Sending the Central Auth Info
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central Auth Info Allocated PMKLen = 32
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be PMK: pmkActiveIndex = 0
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be EapolReplayCounter: 00 00 00 00 00 00 00 01
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
    apfMsEntryType = 0 apfMsEapType = 13
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name:POSTURE_REDIRECT_ACL 
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 6166, Adding TMP rule
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
      IPv4 ACL ID = 255, IPv
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206  Local Bridging Vlan = 220, Local Bridging intf id = 0
    *Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5761, Adding TMP rule
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Replacing Fast Path rule
      type = Airespace AP - Learn IP address
      on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
      IPv4 ACL ID = 255, 
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206  Local Bridging Vlan = 220, Local Bridging intf id = 0
    *apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
    *pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    *pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
    *spamApTask6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be spamEncodeCentralAuthInoMsPayload: msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
    apfMsEntryType = 0 pmkLen = 32
    *DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 325,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP setting server from ACK (server 10.0.17.85, yiaddr 10.130.130.120)
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 DHCP_REQD (7) Change state to WEBAUTH_REQD (8) last state DHCP_REQD (7)
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) pemAdvanceState2 6671, Adding TMP rule
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Replacing Fast Path rule
      type = Airespace AP Client - ACL passthru
      on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
      IPv4 A
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206  Local Bridging Vlan = 220, Local Bridging intf id = 0
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Successfully plumbed mobile rule (IPv4 ACL ID 1, IPv6 ACL ID 255, L2 ACL ID 255)
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Plumbing web-auth redirect rule due to user logout
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Assigning Address 10.130.130.120 to mobile 
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
    *DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
    *pemReceiveTask: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 Added NPU entry of type 2, dtlFlags 0x0
    *IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Pushing IPv6 Vlan Intf ID 0: fe80:0000:0000:0000:f524:1910:69f0:9482 , and MAC: 00:24:D6:97:B3:BE , Binding to Data Plane. SUCCESS !! dhcpv6bitmap 0
    *IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Link Local address fe80::f524:1910:69f0:9482 updated to mscb. Not Advancing pem state.Current state: mscb in apfMsMmInitial mobility state and client state APF_MS_STATE_A
    *DHCP Socket Task: Aug 12 10:58:28.581: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 10:58:28.589: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 11:00:07.959: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 11:00:07.967: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    *DHCP Socket Task: Aug 12 11:01:59.153: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
    Can you see any obvious reason why the NAC agent wont pop up?
    Thanks
    Mario

Maybe you are looking for

  • My iPhoto library won't open

    I have iPhoto 7.1 that shows up in my applications folder. Apparently, I upgraded to iPhoto 9.3 according to the App Store but it does not show up on my computer, When I try to install 9.3, it says I need 9.1. My real problem is that the Library has

  • Invoking a composite deployed on local install - SOA Suite

    Hi All, Morning....need some help with this issue we are facing. Currently have installed the SOA Suite 11g locally onto our windows machines , created one domain for the web logic server .have started the servers as well and able to login to the EM

  • LOB Segments

    Hi How is the size of the LOBSEGMENT caluclated? We carried out an insert of around 50 odd columns into a table that contained a CLOB value, but we observed that LOBSEGMENT value was a very huge figure, around 400mb, though the entire data contained

  • Error Service Provider Configuration

    Hi When I try to save the configuration of the service provider, I'm getting the following error message: Warning: you must define an appropriate mapping from Account Attribute "xml" for the selected resource. If "Compress XML User" is selected, the

  • Changing hex string display format

    When a string control is in hex display format any data typed is displayed in groups of 2 bytes like AABB CCDD. Is there any way to display them in separate group of single bytes like AA BB CC DD?