Changing a ATA hard drive to a SATA hard drive

I have a TouchSmart tx2-1275dx and bought a SATA hard drive. Connector pins are same config, but  different connector. Can a SATA be used in place of the old ATA..If so how to connect?  Thanks!

An adapter for this does exist.
However I seriousely doubt that you could install it in your notebook whilst
the adapter is attached.
Aside from that I couldnt tell you that it would actually work.
I would suggest buying a PATA drive as it was designed for.
If you want to check on the adapter, I know that Frys sells them.
I have a store locally, you may also or check their Website.
GL

Similar Messages

  • No Windows 64 bit Driver for GT30L SATA DVD Drive

    I recently updated my compaq presario to Windows 8.1.  I've been pleased with the change but Windows installed an incomaptible driver for my DVD drive.  It installed the driver for the 32 bit OS.  From what I've learned 32 bit drivers can't work in a 64 bit system.  Here is a link where I discovered this:
    http://www.driverscape.com/download/hp-dvdram-gt30​l-sata-cdrom-device

    Hi Geographygeek,
    Welcome to the HP Support Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I saw your post regarding the problem finding the driver for you DVD drive. If you can provide your product number for your Compaq Presario I will see what I can find for you.
    Thank you,
    Please click “Accept as Solution ” if you feel my post solved your issue.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Thank you,
    BHK6
    I work on behalf of HP

  • DOS driver for XA52P (SATA DVD drive)

    Hi,
    Is it possible to get this drive to work with MSCDEX in DOS?
    Which port address and interrupt does SATA use?
    -Leif

    Hi Geographygeek,
    Welcome to the HP Support Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I saw your post regarding the problem finding the driver for you DVD drive. If you can provide your product number for your Compaq Presario I will see what I can find for you.
    Thank you,
    Please click “Accept as Solution ” if you feel my post solved your issue.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Thank you,
    BHK6
    I work on behalf of HP

  • Replacing a ATA with a SATA hard drive

    I have a Pavilion dv9000 laptop. My hard drive is getting full. Can somebody please tell me if I can replace the ATA hard drive with a SATA hard drive.
    This question was solved.
    View Solution.

    Thank you for your help

  • SATA Hard Drive to IDE Hard Drive adapter ????

    Good afternnon.
    Has anybody had experience with this eBay contraption?
    SATA to IDE Adapter (“Convert SATA Hard Drive to IDE Hard Drive”)
    Connect a SATA hard drive to you IDE motherboard with this SATA to IDE Adapter! Turn your SATA hard drive into IDE interface hard drive. It features the JMicro JM20330 chipset and supports 3.5-inch SATA hard drives. It's compliant with SATA specification and supports up to 2TB hard drives!
    When IDE hard drive price is going higher and shortage, but plenty of SATA Hard Drive available in low price! You can try to use this! It is tested to support up to 2TB SATA hard drive, while largest manufactured IDE hard drive capacity is 750GB. Now you can have 1TB IDE hard drive or even 2TB IDE hard drive!
    Support most hard drives, tested 2TB capacity SATA hard drive, under DOS, Windows XP, Vista, Server 2003 and more...NO SOFTWARE DRIVER REQUIRE, BIOS Detected!"
    Thanks for your time.

    Not that exact one, but others much like that have worked fine.
    And here it looks like the identical one & specifies OSX also...
    http://www.cooldrives.com/satoidecofor.html

  • SATA II drive in a SATA slot of  PowerMac Quad G5: 1.5GB/sec vs. 3.0 GB/sec

    I have a Quad G5 PowerMac with a Hitachi Deskstar® 7K500 (HDS725050KLA360) 500 GB SATA II Hard Drive in the upper hard drive slot. Profiler says this slot is a Serial-ATA slot. Does a SATA II drive in a SATA slot communicate at 1.5 GB/sec instead of 3.0 GB/sec? Any problems with adding a second internal Hitachi Deskstar® 7K500 (HDS725050KLA360) 500 GB SATA II Hard Drive?
    PowerMac Quad G5   Mac OS X (10.4.8)  

    Not sure how you landed here. This is the discussion area for the iBook G4.
    You probably want to ask your question in the Power Mac G5 discussion area.

  • Can Any SATA Drive (including SATA 1 drives) be Used on MacPro?

    Can one install and use any SATA drive (including a SATA 1) drive on a Mac Pro?
    I am thinking about using a WD Caviar SE16 but it would appear to be a SATA 1 drive (1.5 GB/s drive).
    Do all SATA drives have the same connector (that is compatible with the mating connector inside the MacPro)?
    Rob

    While SATA II drives should provide generally better performance any SATA drive will work in a Mac Pro.

  • My IMac 21.5 mid 2010's HD is going bad on it, after upgrading to mavericks it slowed way down and after it shut off and now won't come back on, would Seagate Barracuda ST2000DM001 2TB Serial ATA Hard Drive - 7200RPM, 64MB, SATA 6Gb/s worked?

    My IMac 21.5 mid 2010's HD is going bad on it, after upgrading to mavericks it slowed way down and after it shut off and now won't come back on, I call apple support and they told me to bring it in but the nearest store is about two hours away. They said I need it to erase my hard drive but I have too many family pics on it.
    would Seagate Barracuda ST2000DM001 2TB Serial ATA Hard Drive - 7200RPM, 64MB, SATA 6Gb/s worked on it? I could replace the internal and get an enclosure for the original until I get the pics out of it?
    Please advise, it's like five years of family pics I don't wanna loose them and I am worried.
    Thanks
    Al Florez

    A Brody,
    I really apprecate your very quick respond, Its too late to back up as of now, my hard drive wont load at all so I cannot follow your instruction to back it up. Learn a hard lesson but I will from now on following your link.
    Also my hard drive it is not available to do the free exchange program.
    I read the OWC instruction on how to replace the drive I was just wondering if the 2TB would work on it instead of the 1 TB they offer, I specifically asked for the Seage Barracuda because I had great experiences with it on PCs.
    Again, Thank you

  • ATA internal hard drives and SATA hard drives?

    I've been searching through the posts and am starting to think I've got the oldest running Mac Mini!
    My Mac Mini is installed with a 40 gb ATA hard drive and I think I need to upgrade to a larger internal drive. Although 80-100 gig's would be enough (I have a 250 gig external Firewire drive, I would prefer to go to a 160-320 gig drive, but all of the drives I've found in that size range are SATA drives. From reading the posts I've found so far, it looks to me as if my Mac won't host an internal SATA drive. Can anyone confirm that for me? Am I stuck with ATA drives only? If I'm limited to ATA drives, does anyone know where I can find a large ATA drive suitable for my Mac Mini?
    I appreciate any help or advice anyone can offer.

    You are limited to ATA drives.
    [Here|http://eshop.macsales.com/MyOWC/Upgrades.cfm?sort=pop&model=210&type=DataStorage&TI=0519&shoupgrds=ShowUpgrades] is a nice list from OWC.

  • Q ab. Hard Drive upgrade; PATA/SATA, S.M.A.R.T., HDD Controler

    I have a few questions about replacement hard drives for my PowerBook G4 12" 1.0 GHz DVI. (I am also going to upgrade the hard drive in my wife's Powerbook G4 15" 1.33 GHz Combodrive, but I think the questions/answers below will apply to both. I'll just deal with my 12" for ease here.)
    I have read Apple's specifications and searched all over to find detailed information about ATA ratings and compatibility, and I'm still in the dark about a few things. I'm interested in a 160GB or a 250GB internal drive to replace my 80GB (which did come standard as an optional feature, although this is my second 80GB--I burned the first one before my Applecare expired), and I'm looking at the following drives, for instance:
    HITACHI Travelstar 5K160 HTS541616J9AT00 (0A28419) 160GB 5400 RPM 8MB Cache ATA-6 Notebook Hard Drive - OEM
    http://www.newegg.com/Product/Product.aspx?Item=N82E16822146200
    Western Digital Scorpio WD2500BEVE 250GB 5400 RPM 8MB Cache ATA-6 Notebook Hard Drive - OEM
    http://www.newegg.com/Product/Product.aspx?Item=N82E16822136159
    Questions:
    1. HDD Controller limit to internal drive capacity: I've read that older powerbooks (whatever this means, it wasn't specified) may have a 128GB limit, supposedly meaning that the HDD controller will only recognize 128GB on an internal drive. Anyone know if this is true? How do I find out? It isn't published on Apple's spec page for my machine. And, if such a limit does exist for my machine, can I install a 160 GB and get the full 128GB? (b/c a 120GB will only give me 100+ usable after all.) Will the fact that the drive is lager than the total recognizable amount mess up the cataloging, data retrieval, reliability, stability...?
    2. ATA-100 vs. ATA-6 vs. ATA-7 vs. PATA vs SATA. My present 80GB TOSHIBA MK8025GAS just says ATA in the System Profiler "Protocol" field for the ATA drive. I presume that the SATA is a later, more recent, non-backwards-compatible format/pin configuration/?. I presume the 100 refers to the 100mb/s data transfer rate, which is what the Apple specifications have for my machine. The drives I am looking at, by and large, are rated at 100mb/s. They all have other specifications, however (ATA-6, ATA-7), and I am hoping to hear that they do NOT refer to pin configuration differences.
    -Q- will PATA and SATA drives both fit my machine, or does the "Ultra ATA/100 hard drive" listed in the Apple Specs for my machine mean that the pin configuration/compatibility will only work with PATA drives? Thus, Is Parallel ATA what I have and need?!?! Will a faster SATA drive work in my machine? Would I be able to swap it out into a MacBook Pro when I upgrade next year? (i.e. are SATA drives &/or boards backwards compatible with PATA drives? And are PATA drives &/or boards forward compatible?)
    3. S.M.A.R.T. verification capability. I am unclear as to whether this capability is essential and which drives provide it. Some information states that Hitachi Travelstar drives DO support S.M.A.R.T. verification, but such is not listed on their information about the drives. My present 80GB Toshiba DOES have this capability, so System Profiler says. Before my previous drive failed, SMART notification may have saved me (though it's unclear if it actually made any difference--it's just notification, after all, right?), alerting me that the drive was failing and thus giving me enough time to get the last bit of un-backed-up data off the drive before it died altogether. (This is a presumption based on changing S.M.A.R.T. status notifications in System Profiler and from Disk Utility Repair Disk reports). In fact, however, I don't really know what SMART verification is, and thus I don't know how important it is.
    -Q- How important is S.M.A.R.T. verification capability? And what is it really?
    -Q- which manufactures support it?
    Many, many thanks for any insight.

    Jeremy:
    does, that the Seagate Ultra ATA/100 which I'm about to buy will not work with an Intel-based Mac?
    Your Intel-based Mac needs a Serial ATA (SATA) HDD instead of ATA or ultraATA, PATA etc. Not knowing the specs of your IntelMac select your Intel Mac here and navigate to your Model for a list of compatible HDDs.
    I do intend to install them myself. I haven't had this G4 open, but I put 2 HDDs in my previous G3 without issue, so I think I'll brave it, armed with iFixit instructions.
    Since you have done it before, this addition may be superfluous, but here are few tips you may find helpful:
    • Print out the ifixit directions as well as the screw guide ahead of time.
    • Be sure you have the right tools. You don't want to damage the screw heads or you may never get them out. And the correct size Torx screw driver is critical.
    • I use small medicine cups one for the screws in each step. I nest them so that the last ones out and the first to go back in are on top. You can use an ice cube tray, egg carton, dixie cups etc. (Some users report cutting up the screw guide and placing the applicable section in each container.)
    • Be very careful pulling out leads. Hold the lead as close to the plug as possible and wiggle (the plug ) to loosen its grip. Don’t hold the wires and pull as that can damage the cable, or worse, in some instances pull the wires out of the plug. Indeed, some users have pulled the socket off the logic board! Use needle nose pliers or tweezers if you can access the plug, or nudge the plug with a small instrument to help loosen its grip.
    • Use force gently in removing parts. Separating upper and lower case takes some doing. Use a plastic tool (spudge) so as not to leave marks.
    • Refer to the screw guide when reassembling computer. Putting longer screws in the wrong place can perforate the circuit board.
    Please do post back with further questions or comments.
    Cheers
    cornelius
    PS: Thank you for leaving feedback in Apple Discussions by marking the "solved" post.

  • Does anyone know when the Mac Pro switched from ATA to SATA DVD Drives

    Does anyone know when the Mac Pro switched from ATA to SATA DVD Drives ?
    I tried to find this answer online but failed.

    Appears the Mac Pro (Early 2008) is the last model to suggest Ultra ATA/100 optical.
    And with an optional card, use Serial Attached SCSI via Mac Pro Raid.
    This kind of information gets sketchy in that the hard drive bus and other parts are SATA
    and only this (and earlier) model Mac Pro has optical drive interface w/ Ultra ATA/100. The
    logic board on the early 2008 appears to have two Serial ATA ports, 3.0GBPS; so to check
    these, you may need to look into specification in iFixit.com repair guides, any takeapart
    guides, and note specifications in everymac.com and those from mactracker.ca.
    The MacPro after Early 2008 model build series (Early 2009) appears to sport an optical
    drive with 18x speed, compared to Early 2008 & before, whose drives indicate 16x spec.
    Other changes may be indicated by certain parts and differences; processors, graphic
    support, and those kinds of things. 2008 shows dual-core, afterward, quad-core.
    So on what little I found, that would appear to be the divide or when optical drive spec
    on the logic board changed from Ultra ATA/100 to SATA versions. But double check.
    Good luck & happy computing!

  • HT5634 How to put windows 8 on MacBook Pro via sata hard drive USB off of other computer

    Hi I have recently purchased a MacBook Pro 15 retina. My old laptop was windows 8 but the motherboard crashed and I have the sata hard drive that has all of my data info including OS would I be able to use the OS on Boot camp without purchasing a new license? Also how would I do that? I have put the hard drive into a portable USB device so I can access it via USB 3.0.

    Others will give a better answer, but I suspect that Windows validation will consider this a "significant hardware change", meaning that it will stop working and/or you won't be able to update. Even so, it costs nothing to give it a try and see what happens.

  • How do i install sata hard drive?

    ok, i am using right now my sony dvdrw on ide1 as master and ata hard drive on ide2 as master, booting to the hard drive. i am going to install an sata hard drive and use that as the boot drive, the normal ata as a storage drive only. how will i install the sata drive? do i install it to sata 1 and then durring the install of windows xp tell it to hit f6 for third party scsi drivers and then use the intel sata floppy driver disk that came with my board? it's the MSI-6728 board. or is there anything special i need to do in the bios or what?
    oh yeah. what connection for power should i use? my powersupply has sata and normal, so should i use the sata power connector? and then what's this about legacy or something in the bios, or am i wrong?

    Well first of all, you dont install the Intel S-ATA Driver Disc unless you are going to create a RAID Array....Go into the BIOS and on the "On-Chip IDE Configuration" Page Set the Options like this.........
    On-Chip ATA Operate Mode : Legacy
    ATA Configuration : P-ATA+S-ATA
    Keep S-ATA Enabled : (Greyed Out Yes)
    Keep P-ATA Enabled : (Greyed Out Yes)
    P-ATA Channel Selection : Both
    Combined Mode Operation (At first you have to set this to P-ATA Channel 1, then switch after you Move Windows to S-ATA)
    Configure S-ATA As RAID : No
    Then you are Going to have to Install the OS on The SATA and Just Move the Files that you want to save from the P-ATA HDD and then Remove the P-ATA Drive from the "Boot Device" List in the BIOS....
    You really should List Your Full System Specs. When you POST...Create a "Signature" with your Forum User Control Panel...........Sean REILLY875

  • Installing a second SATA hard drive - Problems booting

    Hi,
    I currently have one Maxtor 160GB SATA hard drive in my system with my operating system installed. I have another identical hard drive that I'm attempting to install now, into the second of five available SATA ports on my MSI P965 Neo motherboard.
    When I plug in the second hard drive, though, Windows will not boot. It gets to the Windows logo screen with the progress animation, but before even the animation can begin, it stops and the screen freezes. This does not fix itself with waiting.
    My boot priorities are set to: DVD-ROM, CD-RW, hard risk. The hard disk priorities are also as they should be to my knowledge - although it can be tricky because when ordering, both disks have the same name. I have tried with either one on top of the list, and you cannot remove a drive from the list alltogether.
    The SATA cable is in perfect condition. My BIOS is up-to-date.
    When I plug the hard drive in when the system is already running, Windows will detect it and files can be written/read flawlessly. As soon as I restart, however, I run into the same issue.
    The first HDD, with the OS on it, is in SATA 1, the second HDD is in SATA 4. Ports 3, 6, and 7 are unused.
    I'm out of ideas at this point, I don't see any other options that need to be changed.
    I'd appreciate any input you can offer - thanks in advance!

    I would debug this drive you are talking about which clears off all data and partitions information. Take out the good drive and leave in the dodgy one. Boot to a floppy with this dell win95 boot disc.
    http://support.dell.com/support/downloads/download.aspx?c=us&l=en&s=gen&releaseid=R19775&formatcnt=1&libid=0&fileid=19601
    When at the A: prompt: type debug and enter, you get a (-) prompt and then enter the following script exactly:
    F 200 L1000 0 (enter)
    A CS:100       (enter)
    xxxx:0100 MOV AX,301  (enter)
    xxxx:0103 MOV BX,200  (enter)
    xxxx:0106 MOV CX,1     (enter)
    xxxx:0109 MOV DX,80   (enter)
    xxx:010C INT 13    (enter)
    xxxx:010E INT 20   (enter)
    xxxx:0110             (enter)
    g                        (enter)
    q                         (enter)
    restart your system.
    Now you can put back in your first drive as well, boot up into windows and use the disc manager to repartition and format.
    Old school! If you are still having problems I would replace the drive.

  • Two SATA Hard Drives, Main Drive only shows up in Bios if PC is off

    I am having a devil of a problem.  My main hard drive is a SATA Seagate 500GB, my other HD is a STAT 80GB that I use for a scratch drive for Photoshop.  When I boot from the PC being off, the MB recognizes my Seagate 500 Sata HD.  When I reboot, it cannot find the 500 GB and I get the NTLDR is Missing message that system files aren't found.  This occurs no matter how often I reboot.
    I have swapped SATA cables on the drives and that did not make a difference!  The cables are securely connected, as are the power cable.
    XP Professional SP3, latest updaates
    K9A2 Platinum Ver. 1, Bios Ver 2.8.1030.0032
    AMD X3-720, 4x 1GB- OCZ Platinum Ver 2, 8500
    Ultra 700w power supply
    Fastrack - what does it do?

    "It is the Promise RAID controller, that controls SATA ports 5 & 6. If you're not using them, you can disable the 'Extra RAID Controller' in BIOS (under Integrated Peripherals)"   
    I am u7sing the 5th SATA slot for the extra esata pieces.  I will turn them off.
    "Did this system ever work?
    What did you alter before this happened?"
    I replaced the CMOS battery.  It was dying.  I checked it on two separate battery checkers.
    "Looks to me as if Windows has messed up partitions in some way.
    Check the following, please:
    - is the Windows disk set as frst boot drive in the bios?
    - Is NTLDR actually on that drive in the root? (You must let Windows show hidden/system files).
    - Is the drive detected by the bios at a reboot? (Does it show in the POST-screen?)"
    Floppy Drive first, then CD-ROM (Sata), then the Seagate HD.
    NTDLR is on the drive in the Root.  When it recognizes the drive and boots from it, it is fine.
    No, it is not detected at a reboot.  It does not show in the POST screen.
    "You have a Q-Tec Power Supply? Change that first and come back later... "
    Is the Ultra brand Q-Tec?  It has a lifetime warranty...

Maybe you are looking for