Changing Default System announcements in Unity Connection 9.1.2

Dear Experts,
I'm setting up Auto Attendant and we have two language options, with different sub-menu's.
We have the recordings in male voice. And when I route the an Input Option (lets say '2') to alternate contact number (lets say extn 500), we hear the default announcement "Wait while I transfer your call", which is in female voice.
Please advise how can we replace this announcement with a custom announcement. Similarly for error and invalid entries.
Also, I need to play these announcements in different language depending on the language selection. how can we achieve this.
Your help will be much appreciated. thanks.

You cannot replace any system recording with your own, if you want them in other language, you need to install the locale.

Similar Messages

Changing Default & System Master Pages In SharePoint 2013

I want to change the system master page & default master page of a SharePoint 2013 site collection. In Site Settings in the Look & Feel section Master Page is not at there. But there is Design Manager. In the design manager where can I change the
above mentioned Master Pages.

Hello,
If publishing is activated you can use the page /_layouts/15/ChangeSiteMasterPage.aspx
You can also use the Design Manager. Choose a theme and then you'll be asked for fonts, colors and...master page.
Hope this helps.

Changing Portal System Announcement description

Hi,
How to change Portal home page system announcement like description and texts.?
I went through system admin -> themes..but didn't got it.
Thanks
Praveen

Hi,
it is fine if you Do it as Online Editing. Just make sure the Server where you are modifying is a central instance. If in case if it didnt reflect or if you dont find sufficient options to modify, You can just right and save the file in Your system as ...htm or ...html(based on what was the File type). Modify it and upload again with option view-> folder-> upload. if you are doing this way manually, Make sure the Overwrite happens, coz some times the file extension may not match.
Secondly, if you want to add some refrerence to some files in this html being modified, Make sure the path of File refrence starts with /irj/go/km/docs/documents/.....
I hope this helps.

CHANGE DEFAULT NAME/SECURITY SETTINGS = LOWER CONNECTION SPEED

I have a Linksys WirelessN Router--If I use the router with all of the default settings I can achieve cable speeds of 300mbps. Fantasically fast!!! As soon as I change the name of the router from "Linksys" to any other name, my speed drops back down to 54mbps. I also changed the security settings to "PSK Personal" and added a personal password so my system wouldn't get "hyjacked." Any thoughts?

Hi… logon to router’s setup page, try changing Radio band to wide 40MHz, wide channel to 9, standard channel to 11, go to advanced wireless settings reduce beacon interval to 50, fragmentation and RTS threshold to 2304, change N Transmission rate to 270MBps…wireless security should be PSK personal, also try upgrading latest firmware on router, check whether it makes any difference or not.

Is it possible to change Automated Attendants announcements in Unity 8.5.1?

I would like to change the standard AA announcement 'Please hold while your call is being transferred to ....' when a caller selects a call handlers option. I would like to notify callers they are being transferred outside our agency instead when the option is chosen.

No, that message (system prompt) is not customizable - you can turn it on or off with a configuraiton option on a per handler/user basis but you cannot customize the prompt itself.

Cisco Unity Connection 8.6 not getting CLID information from CUCM 8.6

Hello,
Currently Running:
Cisco Unified Communications Manager 8.6.2
Cisco Unity Connection 8.6.2
Problem:
when any outside caller leaves a voicemail, the caller number information is not being sent to unity.
example, I call with my cell phone, 817.555.1234 to my Cisco 7940 phone and it shows the CLID information that i am calling with. iDivert to voice mail, Leave a message. Playback message and just the default message information from Cisco Unity.
we currently upgraded from CUCM 6.1.3 and Unity 5. before i could press 9 and get the caller information.
I have viewed the "Playback Message Settings" and selected "After Playing Each Message, Play" and selected Sender's Information. and also selected "Include Extension and Sender's ANI"
upon playing the VoiceMail after the message i get the default message "From Cisco Unity Connection Messaging System"
I also have the message relaying to my E-mail and I get the same in the subject line.
"Message from Cisco Unity Connection Messaging System (Unknown extension)"
This tends to be a big deal with the Sales team as customers will call and say "Call me back"
But any Internal Calls show the correct information, proper greeting, extension information even on the relay to e-mail.
Any help will be appreciated.
Thanks
Tim

Found another post that referenced Cisco Bug ID CSCti37610.
CUC plays message is from Unity Connection Messaging system
Symptom:Before message playback, Unity Connection plays the message is from Unity Connection Messaging System instead sender's ANI
Conditions:Problem was observed on Unity Connection cluster and appropriate services are not rebooted after changing the SMTP domain name
Workaround:
Restart the Unity Connection servers
It should have been fixed in 8.5 but we did change the SMTP domain name on 8.6 and now see the problem. Will schedule a reboot and see if the issue goes away.

Import Export from CUE to Unity Connection 8+

After looking on CiscoUnityTools.com I see there is one CUE tool for importing Users and recorded name WAVs from CUE into Cxn 8+
Does anyone have a method for moving all the users AND voicemails from CUE systems into Unity Connection, any version?

Hi there,
There are no "free" tools that will migrate greetings and messages
from CUE to Connection.
The one place to look is @ Cisco partner CommonVoices "Now There";
http://www.cisco.com/en/US/prod/collateral/voicesw/ps6789/ps5745/ps6509/solutions_partner_cuc.pdf
They do claim to;
Switch from any traditional
system to Cisco Unity®
Connection
• Greetings, name
announcements, existing
messages, and call trees are
all retained along with
message status
• 10 years of experience
migrating millions of mailboxes
worldwide
http://www.commonvoices.com/products/NowThere.php
What many people do when migrating to a new voicemail system is to leave the
old system accessible for a period of time so that users can access their old
messages. This is what we did when migrating from Octel to Unity Connection
Cheers!
Rob
"What you don't have you don't need it now"
- U2

Issue on Cisco Unity Connection after performing 'utils ntp restart'

Hello everybody.
There's a client with Cisco Unity Connection 8.5.1.10000-206. After doing a 'utils ntp restart', the following message showed up:
Communication is not functioning correctly between the servers in the Cisco Unity Connection cluster. To review server status for the cluster, go to the Tools > Cluster Management page of Cisco Unity Connection Serviceability.
The client states that there was no service for 5 minutes and wants to know if performing this task shoud be disruptive or not and if there is any official document from Cisco stating this.
See SrvConnUnity_1.jpg sent by the client after performing the ntp restart.
Right now the service is normal (see SrvConnUnity_2.jpg attached). The client also sent a 'utils ntp
status':
admin:utils ntp status
ntpd (pid 10899) is running...
     remote           refid      st t when poll reach   delay   offset jitter
==============================================================================
*127.127.1.0     LOCAL(0)        10 l   16   64 377    0.000    0.000   0.002
synchronised to local net at stratum 11
   time correct to within 12 ms
   polling server every 64 s
Current time in UTC is : Fri Apr 26 16:01:23 UTC 2013
Current time in America/Argentina/Buenos_Aires is : Fri Apr 26 13:01:23 ART 2013
admin:
Could anybody help me with this? What steps should I take? Many thanks in advance.
Best,
Patricio

Hello Patricio,
On the command line guide you won't see any downtime requirements for the Unity Connection server:
Command Line Interface Reference Guide for Cisco Unified Communications Solutions Release 8.5(1)
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/cli_ref/8_5_1/cli_ref_851.html
Utils ntp restart
This command restarts the NTP service.
Command syntax
utils ntp restart
Parameters
None
Requirements
Command privilege level: 0
Allowed during upgrade: Yes
Also on the caveats i do not see any particular mention for this: (Caveats could be found applicable to CUC)
Release Notes for Cisco Unified Communications Manager Release 8.5(1)
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/rel_notes/8_5_1/cucm-rel_notes-851.html
Breaking up the output of the "utils ntp status" there are are two considerations:
admin:utils ntp status
ntpd (pid 10899) is running...
     remote           refid      st t when poll reach   delay   offset jitter
==============================================================================
*127.127.1.0     LOCAL(0)        10 l   16   64 377    0.000    0.000   0.002
First, you are using the ip address 127.127.1.0 which is the referenced used for the local system clock, the asterisc means is the preferred option as there is no other IP available. This is not a good practice and not recommended.
Secondly the stratum is unreliable, meaning too high to reach or too low to be accepted by Unity Connection.
If you would happen to run 'utils diagnose test' you would have probably seen an output as the following example below:
admin:utils diagnose test
Log file: platform/log/diag1.log
Starting diagnostic test(s)
===========================
test - disk_space          : Passed (available: 25680 MB, used: 7849 MB)
skip - disk_files          : This module must be run directly and off hours
test - service_manager     : Passed
test - tomcat              : Passed
test - tomcat_deadlocks    : Passed
test - tomcat_keystore     : Passed
test - tomcat_connectors   : Passed
test - tomcat_threads      : Passed
test - tomcat_memory       : Passed
test - tomcat_sessions     : Passed
test - validate_network    : Reverse DNS lookup missmatch
test - raid                : Passed
test - system_info         : Passed (Collected system information in diagnostic log)
test - ntp_reachability    : Passed
test - ntp_clock_drift     : Passed
test - ntp_stratum         : Failed
The reference NTP server is a stratum 11 clock.
NTP servers with stratum 5 or worse clocks are deemed unreliable.
Please consider using an NTP server with better stratum level.
Please use OS Admin GUI to add/delete NTP servers.
skip - sdl_fragmentation   : This module must be run directly and off hours
skip - sdi_fragmentation   : This module must be run directly and off hours
test - ipv6_networking     : Passed
And on the RTMT (Real Time Monitoring Tool) you would have seen a Critical event:
Condition:
The best external NTP server, , is stratum , which is unacceptably high. External NTP servers must be <= strata 8 and should be <= strata 5. NTP server strata can be verified using the CLI 'utils ntp status' command ('st' column). Try using different NTP servers.
Problem cause:
All specified external NTP server(s) have unacceptably high stratum values. Network issues exist or the designated servers have unreliable stratum values.
Information is self explanatory and therefore reassures the need of having a NTP different from the server itself.
By the snippet you sent we can know that it is the publisher server, as the Subscriber polls this information from the Publisher.
Installing the Operating System and Cisco Unity Connection 8.x
http://www.cisco.com/en/US/docs/voice_ip_comm/connection/8x/installation/guide/8xcucig020.html
"Cisco recommends that you use an external NTP server to ensure accurate system time on the publisher server. Ensure the external NTP server is stratum 9 or higher (meaning stratums 1-9). The subscriber server will get its time from the publisher server"
Documentation also reaffirms the need for that NTP to be accessible otherwise your system can be degraded. Some addtional information which would be interesting to know is:
- Why did they had to restart the NTP in the first place?
System Requirements for Cisco Unity Connection Release 8.x
http://www.cisco.com/en/US/docs/voice_ip_comm/connection/8x/requirements/8xcucsysreqs.html
"A network time protocol (NTP) server must be accessible to the Connection server"
On the Cisco Unity Connection Serviceability> Tools> CLuster Management screen shot you sent i see that the ports were "Not Available" and that the customer stated "there was no service for 5 minutes".
By no service did they mean that over the phone they heard a disconnected tone or a failsafe message?
Additionaly after the servers resolved from SBR the Subscriber never recovered entirely as it did not start the Conversation Manager service.
Bottom line if they are able to reproduce it then it would be worth a while checking with TAC
Best regards,
David Rojas Peck
Cisco TAC Support Engineer, Unity
Email: [email protected]
Mon, Wed, and Fri 12:00 pm to 9:00 pm ET, Tue and Thu 8:00 am to 5:00pm ET
Cisco Worldwide Contact link is below for further reference.
http://www.cisco.com/en/US/support/tsd_cisco_worldwide_contacts.html

Change Default User Creation OU in Unity 7.x

How do I change where users are created by default when they are added through the web system administration on unity 7.x and Exchange 2003? For a failover system do i need to modify it on both servers, or just the primary? I looked through the reconfiguration guide and didn't see anything that specifically covered this..
Thanks,

Re-run the permissions wizard
http://www.ciscounitytools.com/Applications/Unity/PermissionsWizard/Unity50/Help/PWHelp_ENU.htm

How to Change Default User Directory without changing System Directory

Hi Everyone,
I need to change default User Directory for my JDeveloper 11.1.1.0.2.
Default User Directory = C:/JDeveloper/mywork
Default System Directory = *<JDEV_HOME>/System*
Now I Need to Change it to
My Default User Directory = C:/Monty/JDev11g2/
But System's Default Dir = *<JDEV_HOME>/System*(Same)
For this i explicitly Set variable ide.user.dir to C:/Monty/JDev11g2/ in JDev.boot file as explained in Installation document.
Working fine but it contains System Folder too. I don't want this.
Any Help to find me separate these both as it works for Single User.
Thanks,
Fizzz...

Hi John, You must be right if i'd believe in ghost, A Ghost of System's Folder :-). Well that's true, We should ignore it. But still If someone finds any Clue then let me know.
Thanks
Fizzz...

Is there a way to change the default action for clicking a "Print" button on a website to open Print Preview instead of the default system printer?

When I am at a website that contains a button for printing (Gmail, for example), is there a way to change the way that functions, so that when I click "Print", Firefox will open Print Preview instead of taking me to the default system printer?

You can apply system-wise "negative" color effect under Settings > General > Accessibility, by toggling the White and Black switch - and, in iCab Mobile (and some other, better browsers / PDF readers), its own "night mode" negative color scheme.
Otherwise, no, you can't do anything else except for asking third party app authors to add selectable back/froeground (=text) colors to their apps.
There is an article dedicated to this question: http://www.iphonelife.com/blog/87/do-you-find-your-idevices-screen-be-too-blueis h-or-just-too-harsh-bedtime-reading

Is it possible to change the system's default font?

It is difficult to explain my question, but is it possible to change the system's default font of the script at the top of all windows, and desktop icons? I really think that would add personality to my powerbook. Thanks for any input.

It is possible, and may be changed using the Terminal if you know the commands. However, the easier way is to use TinkerTool <http://www.bresink.com/osx/TinkerTool.html>.
Enjoy!
bd

I have changed default language in the program & have set Language & region in system preferences. My Word (Mac2011) keeps on changing the default language to US english every time I check. Please help!

I have changed default language in the program & have set Language & region in system preferences. My Word (Mac2011) keeps on changing the default language to US english every time I check. Please help!

If you're having trouble making changes to files that are inside your home folder (represented by a house icon in the sidebar of a Finder window), or if you can't get changes to the settings of an application to stick, then please see below.
Back up all data.
This procedure will unlock all your user files (not system files) and reset their ownership and access-control lists to the default. If you've set special values for those attributes on any of your files, they will be reverted. In that case, either stop here, or be prepared to recreate the settings if necessary. Do so only after verifying that those settings didn't cause the problem. If none of this is meaningful to you, you don't need to worry about it.
I've tested these instructions only with the Safari web browser. If you use another browser, they may not work as described.
Step 1
If you have more than one user, and the one in question is not an administrator, then go to Step 2.
Triple-click anywhere in the following line on this page to select it:
{ sudo chflags -R nouchg,nouappnd ~ $TMPDIR..; sudo chown -R $UID:staff ~ $_; sudo chmod -R u+rwX ~ $_; chmod -R -N ~ $_; } 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V). I've tested these instructions only with the Safari web browser. If you use another browser, you may have to press the return key after pasting.
You'll be prompted for your login password. Nothing will be displayed when you type it. You may get a one-time warning to be careful. If you don’t have a login password, you’ll need to set one before you can run the command. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
The command may take a few minutes to run, or perhaps longer if you have literally millions of files in your home folder. Wait for a new line ending in a dollar sign ($) to appear, then quit Terminal.
Step 2 (optional)
Take this step only if you have trouble with Step 1, if you prefer not to take it, or if it doesn't solve the problem.
Boot into Recovery. When the OS X Utilities screen appears, select
Utilities ▹ Terminal
from the menu bar. A Terminal window will open.
In the Terminal window, type this:
res
Press the tab key. The partial command you typed will automatically be completed to this:
resetpassword
Press return. A Reset Password dialog will open. You’re not going to reset a password.
In the dialog, select the startup volume ("Macintosh HD," unless you gave it a different name) if it's not already selected.
Select your username from the menu labeled Select the user account if it's not already selected.
Under Reset Home Directory Permissions and ACLs, click the Reset button.
Select
 ▹ Restart
from the menu bar.

Why can't change default cipersuits of JSSE by java system property?

I am using jdk1.5.0_17,Now I am trying to change default ciphersuits of JSSE by java system property,so all code can be kept unchanged.In JSSE Reference Guide I know default ciphersuits can be customized by https.cipherSuites system property.I run my program by java -Dhttps.cipherSuites=SSL_RSA_WITH_RC4_128_MD5 myProgram
but it doesn't work.the default ciphersuits of jre are always used.I am not able to change it.
any comments? your help will be appreciated.

Well that only works with HTTPS, i.e. with URLs and HttpsURLConnections. If you're using Sockets directly you have to use the API.

Cisco Unity Connection ViewMail Password manual reset after LDAP change

Unity Connection 8.5.1, Viewmail 8.5.4 and Exchange 2010 with 2008 AD
We are migrating to Unity Connection from Unity 7.0.2 and have discovered that when we change our passwords in AD (scheduled every 40 days) this does not get synchronized with viewmail. Users then receive an error indicating the user ID or password is incorrect and then call the helpdesk to find out where to change this setting. Has anyone found a way around this. It is becomking a huge issue with 1200+ employees.
Hopefully it is on a roadmap for cisco as well?
Thanks
Liz

'its really a different user experience' you are telling me!!!
I like the other features that 8.5 brings but the outlook viewmail single sign on design fault is a big mistake. It even effects cupc client as you have to update the voicemail password in their...
I did read all the documentation carefully, it doesnt mention that the passwords do no sync. From a end user point of view, this is a disator. 95% of our users manage the voicemail through outlook, if the password doesnt update in viewmail then they can not retrieve their voicemail.
anyway, i ve spent alot of time and money building the new connection server, but i have no option but to stick to our unity 5 solution. Luckily i noticed this before i changed/migrated people groupwide.
Thanks a million Cisco, I now have to explain this to our IT director....

Changing Default System announcements in Unity Connection 9.1.2

Similar Messages

Maybe you are looking for