Changing from Active to Standby in a DHCP Failover scenario (on the fly) without deconfiguring operation...

Hi all;
Suppose I have set up a scope in SRV01 to be in Active mode. Is it possible to change its state to Standby mode (on the fly) without deconfigurig it and then configuring it again with my desired configuration?
Thanks
Please VOTE as HELPFUL if the post helps you and remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading
the thread.

Similar Messages

I want to use the Function Generator VI to send command signals through the NI 7344 motion controller. This will be a closed loop servo valve system. I want to be able to change from say a square wave to a sine wave on the fly. Idea's?

I am going to run tests that require an actuator to move using various types of arbitrary waveforms such as sine or square. The NI 7344 is hooked to the UMI that is going through a driver for a servo valve. The loop is analog and it is closed. I have played with some of the examples but can't get it to work. I have used the function generator VI to generate a signal but I think I am using the wrong input VI to the motion control board. When I use what I have it moves the servo and then stops. It doesn't continually generate the signal.
I would love to use the controls on the function generator vi to control frequency and amplitude ect. Any help or pointer would be helpful. Thank you in advance.

Hello,
I'm not clear on exactly how you want to use the generated data but I'm assuming they will be used as your target points.
There's a built-in example for motion called 'One-Axis Contour Move.vi'. This example demonstrates how to provide your target points as 1-D array. All you need to do is to replace the input array with the output of the function generator. In order to have it run continuously, use a while loop. You can further program your application so that it'll change the waveform on the fly by monitoring the user interface but this might be little little tricky as you will need to reset the move and load the new generated points while keeping track of your current position.
I hope this helps. Let me know if you have further questions regarding this
application.
Best regards,
Yusuf C.
Applications Engineering
National Instruments

Configure active and standby mac address in failover

Hi guys,
I just have a doubt that, if I configure the active and standby mac address in failover, does it will cause any downtime?
As I planning to configure the active and standby mac addresses in failover during production time and not wish that it will bring any downtime to me.
Besides that, just need some guideline that do I need to put all the interfaces' mac addresses in failover?
failover mac address GigabitEthernet0/0 0022.90fe.2000 0022.90fe.2001
failover mac address GigabitEthernet0/1 0022.90fe.3000 0022.90fe.3001
failover mac address GigabitEthernet0/2 0022.90fe.4000 0022.90fe.4001
failover mac address GigabitEthernet0/3 0022.90fe.5000 0022.90fe.5001

Hi Marius,
Seem like set the failover MAC address was not working for me.
Last friday I was tested the failover MAC address.
TEST 1
1, Power off primary ASA and secondary ASA work as active.
2, 2821 router able to learn the correct arp entries.
TEST 2
1, Power on primary ASA and failover from secondary to primary.
2, 2821 router able to learn the correct arp entries from ASA.
3, Set failover MAC address, power off primary ASA and secondary ASA be active.
4, 2821 router unable to learn the correct arp entries.
TEST 3
1, Removed failover MAC address from secondary ASA.
2, 2821 router still unable to learn the correct arp entries from ASA.
3, Power up primary ASA and secondary ASA still in active.
4, 2821 router still unable to learn the correct arp entries from ASA.
5, Reboot 2821 router and it able to learn the arp entries from ASA.
I am not sure this issue from router or from the ASA. But I guess I will try to upgrade the router in term of software and hardware.

Iwant to buy iphone 4g from apple website but how i can do it iwant the iphone without simcard

iwant to buy iphone 4g from apple website but how i can do it iwant the iphone without simcard
i live in saudi arabia
can i buy the phone from the site
if i can buy iphone 4 from this site can the store send to the saudi post in usa i will send the location if it posible
Thanks !

ooks but when i select the iphone shop i find page and iphone avible on at&t
its noraml i want the iphone without sim card not want at&t
so i have the saudi post adress in usa can the site send to thier?
Thanks 4 support

Finder: Changing from thumbnail view to column view takes me back to the root folder.

Hi,
I was hoping someone could help me with this as it's getting a bit tedious having to re-navigate back to the folder I was in. This problem is only occuring when I am working from an external NAS Drive.
I need to switch between thumbnail view and column view regularly, but whenever I change from thumnails to column - finder jumps back to the root folder, meaning I have to work my way back to where I was.
I can't figure out how to stop this happening! It doesn't happen when changing from column to thumbnails, only the other way round..
Thanks for any suggestions!
Sarah.

Hi Barney,
Thanks for your reply Unfortunately though I already use AFP on the NAS drive and still have the problem, so it seems this is an issue with both AFP and CIFS..

Hi I am new to apple changed from Blackberry all was going well till i down loded the latest apple update for my iphone. then backed it up to Icloud now all my data id gone contacts and all numbers are gone? how do i get them back please help

Hi
I down loded the latest software update for IPhone 4s and then i backed up to i cloud now all me contacts data is gone? please help

Did you do a back up first? If so you should be able to sync to itunes again and have everything back.

Am changing from elements 13 trial to full version,but when opening the editor it keeps asking for me to sign in and input serial number

I have been trying to get elements 13 working for a couple of weeks, after many hours of chat with support and them using remote access, it has still not worked. However, having been on several websites I have made progress and it is now running as the trial version.
The organiser works fine but every time I open the editor, it asks me to sign in and requests the serial number followed by the message "verifying serial number" which disappears after a few seconds. The same thing happens every time I open it as if my serial number is not being accepted
Please help

InDesign CS2 will not be able to open PM files on XP SP3, Vista, or Win 7.
Bob

When I download a Word file from a classroom management database, why won't Firefox open the file without me having to save it?

I have been using Firefox for many years with Blackboard products. In the last six months or so, when I try to download a student's file that is a Word .docx, it won't let me open it without saving it. Word .doc files work fine. I don't have this problem with Internet Explorer, but of course IE is clunky, slow, and doesn't fill in forms. Any help would be appreciated. Let me know if I can supply more details.

Two possible problems. 
1. BlackBoard never supports the latest version of Firefox, for a few reasons. Some schools don't run the latest version of BlackBoard Vista or Campus Edition. Also, BlackBoard upgrades seem to be tied to the "school year" cycle, the changes they make to improve and update their software seem to be rolled out for the fall term so that changes aren't being made during the normal "school year" and possibly causing problems for the schools. That also may be a function of their contract / payment cycles with the schools that use their programs.
http://www2.blackboard.com/tuneup/viewpage?name=tuneup_browser_tuneup_windows_firefox 
Select the link for the version of WebCT Vista or Campus Edition ''(version info is usually at the bottom of each page, in the footer)'' that your school is using, then see which version of Firefox is compatible.
Depending upon which version of WebCT your school is using, you will have to use Firefox 3.6.x, Firefox 3.5.x, or Firefox 3.0.x when accessing the Blackboard site.
My advice is to install the Firefox Portable version that you need for Blackboard on your computer, and use that installation only for Blackboard. Continue to use 4.0.1 for all other web browsing. 
http://portableapps.com/apps/internet/firefox_portable/localization#legacy
2. Firefox uses a Plugin ( you have Office Plugin for Netscape Navigator installed) to open files that aren't "internet files", like word processing documents. 
I can't help you directly with Office, as I use Open Office, but there should be a preference for that Plugin within your Office preferences or options under something like Internet, to have those files '''Display documents in browser'''. 
Or see this to make sure you have your "file type" set correctly. 
http://support.mozilla.com/en-US/kb/Managing+file+types

Using crop to change aspect ratio, but now is there a way to shift the footage without moving the cropped area?

Hi guys!
I'm new and not sure if this is the correct way to go about this. I am using the crop tool to achieve 2.35:1. But is there a way to transform my footage "beneath" the cropped area or do I always have to create a composition in AE and put a black bar layer on top?
Thanks in advance!

I would create the black bars in the title designer and put that on the highest video track of your sequence.

Why does my mouse pointer change from a hand to a downward facing arrow sometimes?

why does my mouse pointer change from a hand to a downward facing arrow sometimes?

the-edmeister, you are a genious. I went to "view" then "toolbars" and de-selected "yahoo toolbar" and then moved the curser over my firefox page and it now works completely including the problem area (the top 3 cm of each screen). Thank you, thank you, thank you, thank you, thank you, thank you. You have no idea how good I feel know on this otherwise cold, windy and rainy day.

Fact columns Datatype is changing from char to int in OBIEE 11g

Hi ,
I am taking measure columns - "product description","tot cost" against a dimension "project name" .
I am generating this report in a planing form and OBIEE .
in planing form :
product description tot cost
project name
P1 A 1500
p2 B 1700
p3 C 1800
in obiee report :
product description
project name
P1 16 1500
p2 17 1700
p3 19 1800
Somehow , measure's datatype are getting changed from char to number , in OBIEE report.
By default , the data type for all fact's is Double .I tried changing that to varchar , but result is same .
Do I need to change anything in physical layer / RPD .
OBIEE version : 11.1.1.6
Essbase version : 11.1.2

Hi ,
Thanks for your reply . To confirm , the data type of product description column is "double" in essbase .
I found out ,thers's a RDBMS table , consisting of two columns - ID, text value . where product description's are in text value's with the corresponding ID's(integer values) .
Now , when I am creating a form in planning , its fetching the text values of product description (there's some inbulit setting's available for this in plannng) .
However , in obiee its fetching the ID values of product description .
So ,
1. Is there any similer setting I can do for OBIEE , so that it's fetches only text value's of product description .
2. If not , then I have to join the essbase fact table with this RDBMS table . I am not sure how to do it .

Cannot change from default printer in Acrobat X by code

pp.printerName = "\\\\print server\\printer"; works flawlessly in Acrobat 9 Standard but will not change from default printer in Acrobat X Standard unless run in the console. I've checked the printer names through the console and they are listed correctly. Javascript enable menu items is checked. I've even tried creating trusted functions (which still work flawlessly in Acrobat 9, but not in Acrobat X). All other printer settings in Acrobat X change as coded once the printer is changed manually.
Any suggestions?

function printFullPEng() {
var pp = this.getPrintParams();
var pSize = this.getPageBox("Crop");
if (pSize[1] > "792") {pp.printerName = "\\\\print-server\\HP Designjet 4000 HPGL2/RTL (Copy 1)";}
else {pp.printerName = "\\\\print-server\\TOSHIBA 4520C PCL6 - Engineering";};
pp.NumCopies = 1;
pp.pageHandling = pp.constants.handling.none;
fv = pp.constants.flagValues;
pp.flags = (fv.setPageSize);
this.print(pp);
This is tied to a menu button. As I say, it works flawlessly in Acrobat 9, but will not change printers in Acrobat X.

Why do a change from one OSX version to another OSX version?

It seems to me that Mavericks OSX is NOT an upgrade. It seems like it is a side-grade since I would still be using OSX, just a side to side change…. The first response noted that some people have difficulty with iPhoto after doing a side to side change to Maverick. I use iPhoto all the time, don't want any problems with that… and another said that the Time Machine backup no longer worked after the change from OSX (Mountain Lion_ to OSX Mavericks)… That is my backup program and I certainly don't want any problems with that. So my ? remains…. why do a side to side change from one OSX to another OSX version??? The answers received are not answering that ?.
Your replys and comments are appreciated.

The reasons for upgrading are:
- Security (there are a myriad of behind-the-scenes security improvements, and some foreground improvements in programs and system services)
- Service compatibility (ie, syncing services like iCloud)
- Application Compatibility (as programs develop, they will drop support for prior versions of OS X).
- Latest and greatest features, if you find them useful.
- Hardware compatibility, with peripheral devices that may no longer support an older version of OS X.
OS X is not just "OS X" with a bunch of peripheral changes to it. There are a number of under the hood enhancements and changes that have fundamentally altered the OS from one version to the next over the years, be it from the kernel all the way through how accounts are handled, to how background services are run and otherwise managed. Granted from one version to the next is sometimes not as significant of an upgrade, but for the most part there are significant changes. In OS X Mavericks, Apple has added major changes to memory and process management, which offer potential to greatly increase battery life, and/or reduce power consumption and wasted CPU cycles.
Of course, with any upgrade you will get the potential for drawbacks, such as initial break-in hiccups.

Cascading physical standby from another physical standby for primary rac

my supplier told me that is possible mount a cascade physical standby from a physical standby for my rac installation.
but according the note "409013.1" seems not:
"Cascading a logical or physical standby database from a physical standby database is supported as long as the primary database is not a RAC database and is not part of a Data Guard Broker configuration - the support status of this configuration is unchanged from previous documentation."
before was possible? do you know why not now?
has anyone mounted? can I allow my provider to mount?
oracle version: 10.2.0.2.0

Is it possible this scenario?YES

How can I make a chart ignore cells until their value is changed from 0?

In the corresponding table, I used conditional formatting to hide zeros in the highlighted row by conditionally changing the text color to that of the table background. However, the zero value's are still represented in the corresponding chart as you can see in the attached photo . How can I make the chart ignore certain cells only until their values are changed from zero? Thanks in advance!
Ryan

Hi Ryan,
Leave the cells empty until they're needed, or, if the cells' contents are determined by a formula, revise the formula to insert a null string if the value is zero.
=IF(your formula = 0, "", your formula)
Regards,
Barry

Changing from Active to Standby in a DHCP Failover scenario (on the fly) without deconfiguring operation...

Similar Messages

Maybe you are looking for