Changing map configure with OMB

Does anybody know how to change map configuration settings with OMB+? I would like to change bulk size, commit frequency, max number of errors, etc.. I could not find a good example of how to do this. Any help would be appreciated.
OWB Client vesion: 10.2.0.3.33
OWB Repository: 10.2.0.3.0
Thanks,
Nick

It may be the mapping has not been analyzed so it is in an early design phase when either the PLSQL (batch) or SQLLoader properties are not available. If you perform these configuration settings after the operators have been added and the map designed then I think you should be OK. If this still fails try performing an OMBVALIDATE on the mapping before settings the config properties.
Cheers
David

Similar Messages

Changing port configuration with Event Manager

Hello,
I'm trying to change the configuration of a port when the port goes down with EEM.
So when an flex connect access-point is disconnected the port becomes an access-port.
I don't want to use the MAC address.
Does anyone has experience with this.
Below is the applet I'm using.
Thanks in advanced,
Michel
event manager applet CONFIG-ACCESS-PORT
event neighbor-discovery interface regexp "(FastEthernet[0-9]\/[0-9]+)" cdp delete
action 100 regexp "(AIR-LAP)" "$_nd_cdp_platform" value
action 110 if $_regexp_result eq "1"
action 200 cli command "enable"
action 210 cli command "config t"
action 220 cli command "interface $_nd_local_intf_name"
action 240 cli command "switchport mode access"
action 250 cli command "switchport access vlan 20"
action 260 cli command "no switchport trunk encapsulation dot1q"
action 270 cli command "no switchport trunk native vlan 88"
action 280 cli command "no switchport trunk allowed vlan 88,100"
action 290 cli command "spanning-tree portfast"
action 400 syslog msg "EXECUTED EEM APPLET FOR ACCESS-PORT interface $_nd_local_intf_name"
action 500 cli command "end"
action 510 cli command "copy run start"

Hi Evan,
For sure! There is a really good example on the configuration guide, and assciated caveats.
http://www.cisco.com/en/US/docs/wireless/controller/7.4/configuration/guides/consolidated/b_cg74_CONSOLIDATED_chapter_0100011.html
Benefits for using LAG is increased bandwidth, and redundancy - especially if you have the two (or more in the case of a 5508 WLC) ports connected to different physical switches, eg a 3750 stack.
Best,
Evan

Help with Class-map configuration - ZBFW

Hello,
I need some clarification regarding the class-map configuration in a ZBFW. I need to allow https,http,ftp & rdp traffic from Internet to few of the servers inside our LAN. So I put the below configuration to accomplish the task (example shows class-map for only https protocol) :
a.)
class-map type inspect match-all HTTPS-ACCESS
match protocol https
match access-group name HTTPS-SERVER-ACCESS
ip access-list extended HTTPS-SERVER-ACCESS
permit tcp any host 172.17.0.55 eq 443
permit tcp any host 172.17.0.56 eq 443
permit tcp any host 172.17.0.36 eq 443
permit tcp any host 172.17.0.45 eq 443
permit tcp any host 172.17.0.60 eq 443
Where 55,56,36,45,60 are the servers inside the LAN (12 more servers are there) that need to be accessed via https,http,ftp & rdp from Internet.
Is it a correct approach? or do I need to change my configuation so that I have to match ACL with my class-map like below:
b.)
ip access-list extended OUTSIDE-TO-INSIDE-ACL
permit tcp any host 172.17.0.55 eq 443
permit tcp any host 172.17.0.55 eq www
permit tcp any host 172.17.0.55 eq 21
permit tcp any host 172.17.0.55 eq 3389
permit tcp any host 172.17.0.56 eq 443
permit tcp any host 172.17.0.56 eq www
permit tcp any host 172.17.0.56 eq 21
permit tcp any host 172.17.0.56 eq 3389
permit tcp any host 172.17.0.36 eq 443
permit tcp any host 172.17.0.36 eq www
permit tcp any host 172.17.0.36 eq 21
permit tcp any host 172.17.0.36 eq 3389
permit tcp any host 172.17.0.45 eq 443
permit tcp any host 172.17.0.45 eq www
permit tcp any host 172.17.0.45 eq 21
permit tcp any host 172.17.0.45 eq 3389
class-map type inspect match-all OUT-IN-CLASS
match access-group name OUTSIDE-TO-INSIDE-ACL
Which one is the correct approach when we consider the performance of the firewall ? Please help me.
Regards,
Yadhu

Hey
I do not agree with Varun, I think the first approach is the best one.
Why? Because when you issue the "match protocol ..." you are usig NBAR wich is an application inspection software, which means that https or whatever protocol is inspected at layer 7, not layer 3 and 4 which the seconds approach does (IP and port-number).
Lets say you use the second approach and an attacker uses some malicious protocol that runs over port 443 or whatever (a port that you opened). That attack would be successfull because all you say, you are going to IP-address 172.17.0.56 over port 443 so go ahead.
But if you are using NBAR, this would not work because NBAR will look at layer 7, inside the protocol itself and look if this really is HTTPS (or whatever protocol).
That's my two cents. Hope it helped!

I changed my sim on my iPhone n reconfigured iMessage, it configured with my number but when i sign in with my apple id it says username/password is wrong while in all other things like FaceTime, App Store it worked with the same id and password

i changed my sim on my iPhone n reconfigured iMessage, it configured with my number but when i sign in with my apple id it says username/password is wrong while in all other things like FaceTime, App Store it worked with the same id and password..
can anyone help me to solve this issue

i just opened my ipad, started my apple account/I.D. and realized I put the wrong e mail. I was having trouble correcting my I.D on the Ipad so I went to my laptop and make the proper changes/slash e mail address I wanted for my apple ID. I got back to my ipad and try to download an app I can't because I have to sign in my apple account and I can't because it still has the irrelivant I.D/email address..
So, i did what you said.. went to setting>app store> tapped on my e mail.. it asked me to sign in (with my invalid emails address showing). I signed in with the password I had created. It said "incorrect".. I went to reset password. I reset password, tried to sign in and it says again "unvalid password".. this is getting irritating. I have been asking and no one knows what to do.

I am Using Apple iPhone 4g 32gb and i have Updated to iOS 6.0 but in Maps i am not able to change the angle with two finger why so ?

I am Using Apple iPhone 4g 32gb and i have Updated to iOS 6.0 but in Maps i am not able to change the angle with two finger why so ? I have also restored it but not getting

I have an iPhone 4 also. If you are referring to the flyover view, its unavailble for the iPhone4. If you want to rotate the map, hold two fingers on the map for 2-3 seconds and rotate them in opposite directions.
Hope this helps

Jboss/tomcat mapping configuration error

I can't even get the combination to serve a .jsp file or .html file. Regardless of the URL that I attempt, I only get a No Context configured to process this request error from tomcat and INFO [Engine] StandardHost[localhost]: MAPPING configuration error for request URI from JBoss. I've tried to access all of the various webapps under the catalina directory and can't get to any of them. I know that catalina is started because the log file shows
<Service name="JBoss-Tomcat">
<Engine name="MainEngine" defaultHost="localhost">
<Logger className="org.jboss.web.catalina.Log4jLogger" verbosityLevel="trace" category="org.jboss.web.localhost.Engine" />
<Host name="localhost">
<Valve className="org.apache.catalina.valves.AccessLogValve" prefix="localhost_access" suffix=".log" pattern="common" directory="../server/default/log" />
<DefaultContext cookies="true" crossContext="true" override="true" />
</Host>
</Engine>

<Connector className="org.apache.catalina.connector.http.HttpConnector" port="8080" minProcessors="3" maxProcessors="10" enableLookups="true" acceptCount="10" debug="0" connectionTimeout="60000" />
</Service>
</Server> in jboss.web:service=EmbeddedCatalinaSX
2002-06-12 23:29:44,760 INFO [org.jboss.web.catalina.EmbeddedCatalinaServiceSX] Creating
2002-06-12 23:29:44,760 INFO [org.jboss.web.catalina.EmbeddedCatalinaServiceSX] Created
2002-06-12 23:29:44,760 DEBUG [org.jboss.deployment.MainDeployer] Done with create step of deploying tomcat4-service.xml
2002-06-12 23:29:44,760 DEBUG [org.jboss.deployment.MainDeployer] start step for deployment file:/D:/JBoss3.0/jboss-3.0.0_tomcat-4.0.3/server/default/deploy/tomcat4-service.xml
2002-06-12 23:29:44,760 DEBUG [org.jboss.deployment.SARDeployer] Deploying SAR, start step: url file:/D:/JBoss3.0/jboss-3.0.0_tomcat-4.0.3/server/default/deploy/tomcat4-service.xml
2002-06-12 23:29:44,760 INFO [org.jboss.web.catalina.EmbeddedCatalinaServiceSX] Starting
2002-06-12 23:29:44,760 INFO [org.jboss.deployment.MainDeployer] Adding deployer: org.jboss.web.catalina.EmbeddedCatalinaServiceSX@7dadcd
2002-06-12 23:29:44,760 DEBUG [org.jboss.web.catalina.EmbeddedCatalinaServiceSX] Setting catalina debug level to: 0
2002-06-12 23:29:44,760 DEBUG [org.jboss.web.catalina.EmbeddedCatalinaServiceSX] Setting catalina.home to: ../catalina
2002-06-12 23:29:44,760 DEBUG [org.jboss.web.catalina.EmbeddedCatalinaServiceSX] Setting catalina.base to: ../catalina
with no errors. I'm confused because I was able to consistently work with previous versions of JBoss with no problem. The configuration seems to have changed radically, is this some recent change that I just can't find a reference to? Thanks for any help.

Hi
For Tomcat 3.x you need to use one of the following options:
(Note: this is with JBoss/Tomcat OR JBoss/Jetty)
Place you .war files in the following location:
C:\jboss-3.0.3\server\default\deploy and the app is automatically available.
If my app's name is DavidOnline.war, when deployed, I can access it at
http://localhost:8080/DavidOnline..
OR
Copy your entire development directory to the deploy direction above, RENAME your
directory from say C:\JspApps to C:\JspApps.war and you can work from that location and see your changes immeadiatly.
There is a file called jboss-service.xml that has some config options, also for the Tomcat bundle there is a file named tomcat-service.xml that has the standard server.xml section.. I suggest you check out the JBoss website, free docs and forums.. http://www.jboss.org.
Thanks, Hope this helps.

IPhoto "metadata changes" and management with possible import to Aperture 2

Sorry for the length of this but I am trying to get to figure out which will be the best product for me without having to waste more time and money. I may already have the best for what I want/need but I am not too terribly satisfied with it in its current configuration, although within itself it is great.
I currently have iPhoto '09 and, as I say, like its ease of use, etc. A feature I have really come to enjoy is the geotagging feature. But one thing that I DO NOT LIKE is how the information is not incorporated into the metadata of the file permanently, such as when I change the date or name of an image. It becomes a pain when I want to export a file for use outside of iPhoto, such as Photoshop, or if I want to email it using my Gmail account.
Questions:
1. Is there a way to have the actual image metadata permanently changed if I have renamed the image, added gps information, or changed the date/time an image was taken? If so, how?
2. Is there a way to export the information and have the information stick?
3. (An Aperture question) I do not have Aperture now but I'm thinking of purchasing it because I understand (may be dead wrong here) that Aperture can do what I need. For those who know, can it do it? If so, is there a way to get my images from iPhoto into Aperture with all of the information attached (name, description, date/time, gps, etc) seamlessly or will I be forced to redo everything?
4. (Another Aperture question) Is Aperture good for organization in and of itself? In other words, can it completely replace iPhoto while still allowing me to enjoy all of the features I currently have (seeing geotags on maps, searching with keywords, etc)?
Do you have other advice for me? If Aperture won't work or you don't like it for some reason, what to you prefer/recommend that will do what I need? Can you provide links to anything that may be helpful?
Thanks for your help and have a wonderful weekend!!!

1. Is there a way to have the actual image metadata permanently changed if I have renamed the image, added gps information, or changed the date/time an image was taken? If so, how?
You can rename an image but that’s not the same as renaming a File. Iphoto renames the image, and using the File -> Export command that title can be written to the IPTC data of the file. Also, if you choose you can use the Title as a Filename using the same Export command. You can also write the gps data using that route too. As for changing the date and time, if you use the Adjust Date and Time command you can opt to have that written to the actual file.
2. Is there a way to export the information and have the information stick?
See above. What there is no way of doing is writing that data to the files inside iPhoto - and no need to.
3. (An Aperture question) I do not have Aperture now but I'm thinking of purchasing it because I understand (may be dead wrong here) that Aperture can do what I need. For those who know, can it do it? If so, is there a way to get my images from iPhoto into Aperture with all of the information attached (name, description, date/time, gps, etc) seamlessly or will I be forced to redo everything?
Aperture works the same way - metadata is stored in the DB, not written to the file unless you choose to on export. It too is a database application. You can seamlessly move the data from iPhoto to Aperture using the ‘Import iPhoto Library command’. You can download a trial of Aperture, and I recommend you do.
4. (Another Aperture question) Is Aperture good for organization in and of itself? In other words, can it completely replace iPhoto while still allowing me to enjoy all of the features I currently have (seeing geotags on maps, searching with keywords, etc)?
Aperture is much more powerful - and complex - than iPhoto. It’s geared for the Professional shooting RAW. I can completely replace iPhoto bar some things: there’s no way currently to tag gps data in Aperture, very limited slideshows and no concept of Faces. I strongly urge you to download the trial. There’s a learning curve there.
Regards
TD

Changing the configurations of pre-configured BOM on a Sales Order

Hello experts,
Our client's business is similar to OEC Computers. However, I am not able to map the following business scenario:
They sell servers to customers however, it is unusual that the client buys the pre-configured model as provided by the principal. therefore, as per the specific requirements of customer they change the configuration of the server.
For e.g. the pre-configured model has 2GB of RAM however, the customer wants to replace the the 2GB RAM with a 4GB RAM.
The replacement is important to track as Inventory will have an affect on it.
Please advise the possible solutions.
Regards

Hi Adeel,
At the time of Production order you chane the 4GB RAM Instead of 2GB.
Traking of the Replacement item you use some Additional query report to be use.
*Close the thread if issue solved.
Regards
Jambulingam.P

How to restrict the authorization to change backgroud configuration

hello , I copy some users from my admin user which contain the sap_all profile. so these uses can change background configuration. now, I want to restrict the authorization that they can only view the background configuration but can not change it . how can I set this authorization? Can I change the sap_all profile? how to set it?
thanks.

Hi,
You can copy the SAP_ALL profile to a new name say Z_SAP_ALL and provide display access to all the authorization object and make sure you remove all the critical tcodes in the Z_SAP_ALL profile.
Once you are done with testing the role assign it to the user.
Also search the threads in the forum...
Rakesh

Error in Proxy configuration with SLM

> Hello Experts,
>
> I am encountring some problems when configuring SLM with Solution Manager 7.01 SP06. I have applied all the settings required for SLM and described on the How-To documentation. I have also read all the forums regarding this issue, but nothing helpful. This issue is the configuration of the proxy settings. We are using SNC for our Saprouter, so I assume that I have to use also the sapserv3 for SLM configuration, with the port 8080.
>
> I have added also these entries on Web Service Container in VA:
> Proxy Host: sapserv3
> Proxy Port: 8080
> Exclude List: myhost.mydomain
> And Save
>
> When I execute the configuration check with the transaction "/n/tmwflow/mopzcfg", I have these errors:
>
> <description>Check Proxy settings for download</description>
> + <config-path>
> <entry>Configuration path: SDT/SDT|cod-zeus|PS1/SDTExecutionService/DOWNLOAD</entry>
> </config-path>
> - <input>
> <entry>Proxy use: true</entry>
> <entry>Proxy host: sapserv3</entry>
> <entry>Proxy port: 8080</entry>
> <entry>Use proxy authentication: false</entry>
> <entry>Check HTTP connection to: http://www.sap.com/index.epx</entry>
> </input>
> - <output>
> <entry>Test Result: FAILED</entry>
> </output>
>- <error>
>- <MESSAGE>
> <ID>java.net.UnknownHostException: BAEx.Failed</ID>
> <CREATOR>SLM: java.net.PlainSocketImpl: Line: 201</CREATOR>
> <TEXT>www.sap.com</TEXT>
> </MESSAGE>
> </error>
> </CheckResult>
> - <CheckResult status="FAILED">
> <description>Check Proxy settings for web services</description>
> - <config-path>
> <entry>Configuration path: WebServicessAddOn/HTTPProxy</entry>
> </config-path>
> - <input>
> <entry>Proxy use: true</entry>
> <entry>Proxy host: sapserv3</entry>
> <entry>Proxy port: 8080</entry>
> <entry>Check HTTP connection to: http://www.sap.com/index.epx</entry>
> <entry>Set Proxy-Authorization</entry>
> </input>
> - <output>
> <entry>Proxy user:</entry>
> <entry>Test Result: FAILED</entry>
> </output>
>- <error>
>- <MESSAGE>
> <ID>java.net.UnknownHostException: BAEx.Failed</ID>
> <CREATOR>SLM: java.net.PlainSocketImpl: Line: 201</CREATOR>
> <TEXT>www.sap.com</TEXT>
> </MESSAGE>
> </error>
> </CheckResult>
> - <CheckResult status="FAILED">
> <description>Check SMP user and SP web service</description>
>
> Configuration path: SDT/SDT|host|sid/SDTExecutionService/DOWNLOAD
>
> please tell me what should I do. Thank you
Edited by: sapmoo on May 7, 2010 11:59 AM

is Done...
I have changed the 8001 Port, by 50100... :S
this is my First Client with both instances in a same Server than I have to use this port... always I have used 800 + number of Instance...
Regards

Change UI configuration dynamically when ever user selects a new value in a drop down field in WebUI

I enhanced the standard activity component (i.e BT126S_APPT ). In this component, in BT126S_APPT/ApptSQ view there is a field 'PROCESS_TYPE' which is a dropdown. I have created a server event for this dropdown. So that whenever user selects a value in that dropdown, a event is called and after that DO_CONFIG_DETERMINATION is called. In DO_CONFIG_DETERMINATION, I am checking the value of 'PROCESS_TYPE' and based on that i am setting different config keys, by calling SET_CONFIG_KEYS( ). But the configuration is not changing in WebUI. When I press F2 in WebUI its showing the config keys( searched for ) as I set, but the found config keys are same as before. I have created the configuration with the new configuration keys. Please help, I am new to crm.

Hello Shakthi,
The easier option would be to convert the DropDownByKey to DropDownByIndex. If you still want to proceed with DropDownByKey then you need to initialise the ALV data again. do the following
1. after changing the attribute-value_set, call the ALV interface controller method SET_DATA and pass the instance of the context node.
2. reintiliase all the ALV settings like edit mode, converting the column editor to DropDownByKey etc....
This will ensure the new attribute value set is reflected in the ALV component.
BR, Saravanan

I updated my Iphone 3gs to last version of iOS and now I can't change my configurations of Mail, Contacts, Calendars.

I updated my Iphone 3gs to last version of iOS and now I can't change my configurations of Mail, Contacts, Calendars.

Generally that is a sign that the iPhone had previously been jailbroken
or hacked to work with other than the original wireless provider. The update
has relocked the iPhone to the original wireless provider. You must
contact them to see if they provide unlocking and if you qualify.
If you can get that far, what does it say when you look at
Settings=>General=>About=>Carrier?

I have changed the configuration of the firefox and I want to change it back

some days ago I have changed the configuration of the my Firefox to have a Firefox with higher speed. But after changing I found that the speed has became slower. I want to change the configuration back to its original setting. Please let me know if there is any way to do it.
may tanks for your helps.
MIMLINUX

Start Firefox in [[Safe Mode]]. When you get to the [https://support.mozilla.com/en-US/kb/Safe+Mode#Safe_Mode_window Safe Mode window] , select '''Reset all user preferences to Firefox defaults''' and then '''Make Changes and Restart'''. You have to be very careful when a site tells you to change Firefox's settings. It may harm your Firefox.

HT5927 Using apple configurator with supervised devises, enabling iCloud/ find my iOS device (after being supervised), backing up that supervised / find my iPhone enabled image, --issue; unable to apply back up to any iOS device (including the orign. devi

Senario:
Need to manage 500 Enterprise iPads
Requirements;
1) Trackable via Find my iOS device (we have 500 iPads and with the 100 device limit per iCloud account for Find my iOS device limit we have 5+ iCloud accounts).
2) Individually named iPads for locating and sending commands to wipe, lost mode, etc.. on map per Find my iOS device (we uniquely name them in Apple Configurator either by using the "sequensetially numbering feature", or by creating individual back ups (yes, 450) with the name specified in the image).
3) Find my iOS device feature enabled in base Prepared or Supervised image (using one of our 5+ iCloud accounts) (image can be created during prepared stage, or in supervised stage) - tried both and have the same issue - which I am getting to...
4) VPP codes for paid apps (all VPP codes purchased with generic account which is the Apple Admin account for VPP purchases). Apple Configurator is set up under a different/ unique Apple account (i.e. not VPP admin account) and not logged into iTunes for any purchases/ services).
Issue: Can not do any following senarios;
A)
1) configure master iOS 7 iPad with iCloud account with Find my iOS feature enabled in Prepare stage (added during preparing stage)
2) configure master iOS 7 iPad with iCloud account with Find my iOS feature enabled in Supervised stage (added after supervising, and then backing up that supervised and iOS Find my iOS device enabled)
B) 1) Apply master image to any Supervised iPad (under senario step A) or senario step B)), including the (Supervised or/ Prepared iPad that was used to create the maset iOS 7 image
Result = fail with Apple generic code "4" ; This is obviously due to Find my iOS device feature enabled during image capture.
According to Apple (see Apple Config. Help) the 'Activation lock' (new feature in iOS 7) will not be enabled on a supervised device when an iCloud account with "Find my iDevice" is enabled. Their "help files" seem to imply after the device is Supervised, and a person (presumably and end user) adds thier own iCloud account with Find my iOS device enabled the activation lock is not enabled and erasing/ reconfiguring with Apple Configurator will not cause reimaging probhlems such as requiring the end user's credentials to reconfigure the device using Apple Configurator (i.e. you won't need the end user's credentials).
Needed: To be able to configure Supervised iPads with iCloud account (Enterprised owned iCloud account) configured on the basse image, which has Find my iOS device enabled, and to be able to apply that base image to all Enterprise iPads without generic apple error code 4 issue.

Hi all
I am trying to replicate these steps in my environment but I am having trouble getting an iCloud backup restored to a supervised device. Can someone clarify the steps? The parts I am unsure on are:
1) Do you Prepare in Configurator with all the institution owned apps? Or do you install them after restoring the iCloud backup?
2) After entering the personal AppleID to restore the iCloud backup, the setup wizard prompts for the Institution/Configurator AppleID, there is an option to 'Skip Now'. Do you enter in the password for the institution account? or do you skip that step?
3) What exactly is on the screen in the 'mini setup assistant' after the restore when you Refresh with Configurator?
Any help would be greatly appreciated!

IPhone mail configured with Gmail alternate address

I'm really stuck.. I have a Gmail account (through Google Apps for Business) that I have configured with Mail on my iPhone using Exchange to connect the account. Everything has been working flawlessly, until my employer made a change to our email addresses, so that we had to set up a new domain alias through Gmail as our "send from" account.
My problem is that I can't for the life of me figure out how to send from this new address from my iPhone.
Finally, I found a post on the web that seems to explain a way to do this, using the OTHER account setup (IMAP) on the iPhone (instead of either Gmail or Exchange): http://modernerd.com/post/535350679/solved-gmail-ipad-iphone-and-multiple-from That seemed to do the trick, except then I realized I would no longer have Push email, which I have really come to rely on.
I tried using the native iPhone Gmail app for a few days, as that seemed to be the only solution, but there's just so many things about that app that really make me miss my good 'ol Apple mail.
Any other creative solutions out there? Thanks for any advice!

yeah, it used to work fine because google was supported exchange on mobile devices up until the end of february or so. they let everyone keep their settings the way they were unless they changed them or deleted them, so that's totally expected. The thing with the push is that gmail no longer seems to be supporting that behavior through native apps on mobile devices because it's something they want their exchange customers to pay for

Changing map configure with OMB

Similar Messages

Maybe you are looking for