Changing modem or router settings for etrade pro

I just installed Mountain Lion and I am trying to get my trading platform, Etrade Pro, to load through Etrade. The system requirements for Macs are:
Macintosh
Sun Java Runtime Environment version 1.6 or higher
1.4 GHz Intel processor or faster
Mac OS X 10.5 or later
512MB unused RAM available for use
Connection speed of at least 128 kbps (broadband connection recommended)
Ports 443, 80 and 7001 enabled
I installed Java and restarted cpu
I have no Idea how to enable Ports 443,80 and 7001, or hoe to check to see if they are enabled.
I have iMac connected to airport extreme with USB. The airport extreme which is connected to comcast modem.

No, a JNLP file is not a Windows file; it's a Java file. Select the file in the Finder and open the Info window. From the Open with menu, select Java Web Start. Click Change All and confirm. Test.
Paralells is a low-level system modification, and it or some other third-party software could be interfering with Java. If you still have problems, continue.
Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, or by a peripheral device. 
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including Wi-Fi on certain iMacs. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

Similar Messages

  • Change the default margin settings for the MS word!

    Hi All,
    BI Publisher version:latest 10.1.3.4
    DB:10.2.0.4
    Oracle Apps:12.0.6
    OS:AIX
    We are facing an issue of which description is as below:
    RTF output is being uploaded through "XML Publisher" Responsibility.
    3.1.9 Header and Footer Margin from Edge Not Preserved in RTF Output
    This issue applies to Versions 10.1.3.3, 10.1.3.3.1, 10.1.3.3.2, 10.1.3.3.3, 10.1.3.4, and 10.1.3.4.1.
    Microsoft Word provides a Page Setup option for specifying the margin for the headers and footers from the edge of the page. This option is available by choosing the File menu, then Page Setup, then the Margins tab, and the From edge box. This margin setting is not retained when the output format is RTF. The output is created with the default margin settings instead. The margin settings do work correctly for other output formats such as HTML, PDF, and Excel.
    So, the "default setting" mentioned here is around 1/2 inch for MS Word which is getting added in the output, even if the margin in template is zero.
    Expected output:
    So what we need to do is -
    1. Check the MS word installation on the application server
    2. Change this default margin setting as top and bottom 0 on the server in the MS word page setup. (I can give you steps to do this in word if required)
    We have tried setting this margin to 0 on client side and generating the output and it makes no difference, so it must be coming from the server.
    We need to know how could we modify the settings and need to know te source and Check the MS word installation on the application server?
    Could anyone please share such an issue faced before!
    Thanks for your time!
    Regards,

    Hi All,
    Moreover,
    Our understanding about the RTF output is this -
    When we generate an RTF report output from Oracle EBS, the word document that is generated is with the settings of MS word that is installed on application server.
    This understanding could be wrong as we have never faced such situation before! We have come to this conclusion because the default settings that we do on client machine do not work.
    And as per the documentation of BI publisher the RTF should always be generated with the default settings of MS word.
    So what you could help us with is this -
    1. See if the MS word application is installed on application server ( if you think this is not application server, but any other server then please check there!)
    2. Change the default margin settings for the MS word.
    Regards,

  • How to change the contact sync settings for icloud? please advise

    how to change the contact sync settings for icloud? please advise?

    There are no settings to change. Assuming you are using Lion 10.7.2 (or 10.7.3) - which you should be - you simply sign in in System Preferences>iCloud and check 'Contacts' and any other data you want to sync.
    If you are using an earlier system you will not be able to sync your contacts, and there is no workaround. However you can sync them with Google or Yahoo contacts, though I don't know how well this works.

  • Router settings for ITouch

    I have been trying to connect my new ITouch with my home wireless, but am having numerous problems.  It won't accept the password.  I have read some of the discussions, but there are so many things listed there.  Right now my router, a WRT54G, is set as WEP with a 64 bit code.  From what I have read, I should change it to a 128 bit and generate a key code for that.  If I do that, will I need to do something different for my laptops, which have been working fine with the wireless?  I don't want to mess things up, as I am not use to dealing with router settings, etc.
    Solved!
    Go to Solution.

    If you change the WEP Encryption from 64-bit to 128-bit,generate the passphrase for you and use KEY 1 to reconnect the wireless network on your laptop.
    Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
    Click on the Wireless tab,click on the wireless tab,Set the Wireless channel to 11-2.462GHz,Provide Unique SSID for the Wireless Network Name(not linksys)...and click on save settings.Click on Advanced Wireless Settings,Change the Beacon Interval to 75,Change the Fragmentation Threshold to 2304,Change the RTS Threshold to 2304 >>Click on "Save Settings"... 
    Now,try to connect the I-Phone and check...

  • Optimal settings for 9800 PRO

    Does anyone know the BEST settings for a 9800 Pro. I do not want to get a program to OC it. I just would rather change the settings than use a program. So if anyone knows what the BEST settings or know of a site that tells you the BEST settings for a 9800 Pro, I would appreciate it very much if you were to tell me.  Thanks.  

    try rage 3d tweak...it has an overclocker too, but you dont have to use it, and it practically gives you full control over the cards settings.
    http://www.rage3d.com/r3dtweak/dload/R3Dtweak39c.zip

  • Best Export / Video settings for Premiere Pro. Help Needed.

    What's the best settings when you want to export a video from Premiere Pro for the web or otherwise. Best settings = good quality video and LOW file size.
    Benchmark : The videos on Apple Trailers. Check them out at http://www.apple.com/trailers
    The trailers are of high quality video, great sounds, and the Large sizes all fall under the 25MB mark. Any ideas on HOW this is done and what
    settings in Premiere Pro CS3 might be able to replicate such standards?
    Any help is appreciated. I normally use Encoder and export using H264 but that always seems to have an Audio lag. Any similar issues?
    Thanks a mil!

    I understand that better quality = bigger file size. That's true in most cases, but there is a way around it, I'm just not sure what that way is. As I mentioned in the original post, the benchmark is http://www.apple.com/trailers . The non-HD videos on any movie page on that site hardly ever exceeds the 25MB mark. The videos are 2-3minutes long, and while they may not be top-notch BD visuals, they look way better than 95% of the stuff that's streamed off the net.
    That's why I asked if anyone had any ideas on how to replicate something like that. Say I had a avi file of great quality, shot with a Panasonic DV Cam. I Capture the footage, do whatever I have to in Pr, and the result is now a 3minute video. I want it exported to a Quicktime file, I want it to look visually pleasing like the trailers on Apple, and I want it to fall under 25MB. I have tried H.264 encoding, regular Quicktime, and Quicktime via Encoder. Nothing reaches the expected quality.
    For more examples visit http://www.passionpictures.com.my/pages/recent.aspx and download those simple 30second clips. All Quicktime, mostly under 5.5MB. If Pr can't do it, then I don't know what can...so I'm sure Pr can do it.
    Problem is, how? Experimentation is definitely a way to go, I get that. But on the basis of the scenario given above...how is it done?

  • Export Settings for Mpix Pro

    Can anyone tell me specific export settings to use for mpix pro? Or, settings in general for commercial labs?
    Thanks,
    Bill

    Changing the DPI or PPI (pixels per inch) setting has absolutely no impact on print quality. The only thing that matters is the pixel dimensions of the image. For instance, if you send an image with pixel dimensions of 800x600 pixels and expect to print a 16 x 20" print from that image, it isn't going to work. There aren't enough pixels regardless of what the PPI setting is. If you want to do the math to determine how many pixels you need that is up to you. I usually just send the full-sized image. Most of the labs that I have used will warn you if there aren't enough pixels. So if you send the full-sized image it doesn't matter whether it's set at 72 PPI, 150 PPI, 300 PPI, or whatever. You still have all the pixels and can print the same quality.
    It's amazing what commercial labs can do these days. I was in a local camera store one day when they have an in-house photolab. And they were printing a very large photo on roll paper. It probably measured somewhere in the neighborhood of 3 x 4' or larger. The quality was very good. I asked them how large of an image was required for a print of that size, and to my surprise they said two megapixels. While I would recommend pushing my luck that far I was really impressed with the quality of the image.

  • Turning Modem and Router off for two weeks?

    Would it have an effect on my Infinity profile if I turned off both the modem and router for a couple of weeks?
    I ask mainly due to concern about the Openreach Modem potential for overheating.
    Thanks for any advice. 
    Please Click On any Text in Blue as that automatically links to information.
    PC (NDEGR)
    Solved!
    Go to Solution.

    If switching it off for a fortnight causes any problems , then there are far more serious problems in the network than overheating modems.
    We would never get any elecrical work done in our houses, and what about the occasional elecrical outages we all get from time to time
    Go on be a
    toekneem
    http://www.no2nuisancecalls.net
    (EASBF)

  • Optimal settings for quicktime pro for imovie hd

    Hi!
    Using QT Pro, I sent an imovie HD file (about 5 minutes) thru using h.264. It all looks pristine! EXCEPT, the transitions from imovie are bumpy, choppy, go backwards, etc.
    This is to be streamed on the web. I've kept the 1920 x 1080 settings in tact.
    QUESTION: What can I do to tweek the settings so the transitions are better? Would changing the key frame rate help? I left it on automatic.
    Thanks for the help!

    2.5millionyears wrote:
    Here is the core question: My machine is an imac with a 2 gig processor and 2 gig of RAM. It should be able to handle a 69 MB file. (It plays back the 2 GB imovie file just fine.) Therefore, I believe the issue is not processing speed, rather, the issue seems to be that of how QT compresses the source video. It is very jerky on my machine, not on the web, not on a slow computer, but on my machine.
    This is not entirely correct. The fact that the video is smaller is probably due to it being compressed by something like the H.264 codec. This actually requires more processor power than the 2 GB file (probably Apple Intermediate Codec) in iMovie.

  • Changing FX plug in settings for channel strip aliases?

    I've been trying to migrate my live performance rig from Kore 2 to Mainstage 3, and truth be told it has not been easy, nor yet successful.  Every time I overcome one roadblock to something that was so easy to set in Kore, another problem presents itself.  Thanks to much help from the users in this group, I got a handle on getting through the biggest obstacle of Mainstage ignoring PG changes to channel strips by using Multitimbral settings. 
    Here's the next huge stumbling block.  In Kore, I was able to set up any instance (roughly the equivalent of a Mainstage channel strip) with a series of insert effects plug ins, i.e. a piano patch with both parametric and graphic EQ, compression, etc. and was able to choose which effect(s) would be in use or defeated for a given performance preset and change the settings of any of the plug ins and be able to save them on a per preset basis. 
    While the capacity to load several insert FX exists in Mainstage, it appears that any changes to an effect are global across the aliases.  While I understand that only voume, pan and expression can have separate settings on an alias, I'm searching for some kind of workaround to this issue.  All I came up with was using separate busses for each FX chain each having their own settings, but that seems like a horribly inefficient use of resources.  Has anyone else found a solution to this problem?

    That is not possible, because an alias is simple the _identical_ channel strip in different patches. Any change will be reflected on all occurences of the alias.

  • I want to change my HDD to SSD for macbook pro 15 2010 need some help

    i want to change my HDD to SSD what will work with my macbook pro 2.66GHz (15-inch Unibody w/Intel Core i7) - April 2010 and do it will make my macbook pro low timp and do my macbook pro will be more faster ?

    Personally I am not a fan of SSDs because they are not cost effective for my personal requirements.  However I do recognize that the days of the disk are numbered, but I suspect that day is still a few years off.
    Crucial is a fine company and is one of the two I personally recommend for RAM (OWC being the other) so I suspect that would be a good choice to make.  They are a consumer responsive company.  Indeed the Amazon price is attractive but before you commit yourself, see if you can find test information and reviews on this product.
    I personally cannot give you first hand information on SSDs because I have none of my own.  But perhaps some one will read this post and chime in.
    Ciao.

  • Best preference settings for MacBook Pro Retina Mid 2012 with 2.7 Ghz Core i7 processor 16GB memory Nvidia GeForce GT 650M 1024MB processor

    (using latest AE CC2014)
    I have a MacBook Pro Retina Mid 2012 with 2.7 Ghz Core i7 processor 16GB memory Nvidia GeForce GT 650M 1024MB processor, doing some heavy AE renderings and just realized that this machine says it has 8 Cores? I'm had not yet turned on Multprocessing in Preferences Should I be?
    Should I leave 1 or 2 cores for other applications?
    RAM allocation per background CPU is defaulted set to 3GB
    Also for Adobe Media Encoder: in preferences under Video Rendering /Rendere it is set at Mercury Playback Engine GPU Acceleration (OpenCL) is that the best config for this computer?

    How much ram?
    The best settings depend on what you are working on. Here are mine for a nearly identical system:
    It's usually best to keep memory blocks in 4GB blocks. If my workflow is more in other apps I'll switch out other apps to 8 gb if things start to slow down. Because of my usual project settings I keep MP turned off on this machine, but for some projects I'll turn it on. If you decide to experiment to MP then keep an eye on the Actual CPU's that will be used and make sure the numbers add up. Other applications and Actual Cores should add up the the total in your system.

  • Windows settings for Webhelp Pro

    When I set my settings in the window option to 2 pane instead
    of 1 pane for my webhelp pro layout It doesn't save my preferance
    and reverts back to "Default".
    Does anyone know if this is a bug and how I can get my 2 pane
    setting to save?

    I had a similar problem when creating a window to use for
    WebHelp: None of the window size settings would save.
    I ended up deleting the window completely from the project
    and creating it again from scratch. That solved the problem.

  • Audio Settings for Premiere Pro CS4 during capture

    During some other discussions regarding audio challenges with PP CS4 someone pointed out that if you analyze a file with G spot it should be in WAV format. I did this and I see my footage is showing PCM Audio at 48000Hz 1536 kb/s tot (2 chnls). Based on the fact that I record SD footage (audio selected to 16 bit 48k) onto a Mini DV tape on a DVX 100B and export via Firewire into PP CS4 does that sound right?
    In the Preferences window I have Premiere Pro WDM Sound selected as the default device (Adobe default windows sound and creative ASIO are the other options) . The input and output in Audio Hardware Settings has the Buffer size sliding bar at about 25% across from the left and the Device 32-bit playback is unchecked.
    I am just worried about what my dialog will sound like by the time it is edited in PP and send to Encore to export to DVD.
    Thanks for any input you can offer.
    Cole

    GSpot should have shown the audio as WAV not PCM.
    These are two different things.  WAV is a computer file format for audio files, much like TXT is a format for text files or EXE is a format for executable files (programs).  This is just the specifications for the file formatting on the hard drive.  It applies to audio only files.  Those which contain both audio and video will not be WAV files.
    PCM (Pulse Code Modulation) is a method of encoding analog audio, turning it into a digital signal.  This applies to both computers and separate components (CD players, DAWs, most cameras).  It is the codec CDs use.  It is also the standard for DV.  Even most WAV files contain PCM audio.
    http://en.wikipedia.org/wiki/Wav
    http://en.wikipedia.org/wiki/Pulse-code_modulation

  • CS6 Export Settings for Apple Pro Res 422 HQ

    My project is 1920 x 1080 (1.0) 23.976 fps, progressive and my special effects guy is asking for the project to be rendered out to Apple Pro Res 422 HQ. I can not find an export setting that offers 23.976 fps and is progressive. I have offered to give him an "XML" file but he is insistant. What can I do?

    I believe you will only find this option on a Mac that has ProRes installed from some other application, like QuickTime Pro or Final Cut.

Maybe you are looking for