Changing native VLAN 100 on SFE2000P to VLAN 1?

The "SFE2000/SFE2000P Gigabit Ethernet Switch Reference Guide" says on page 124 "The Management VLAN is set to VLAN 100 by default, but can be modified." (highlighting is mine).   I'm still searching for how.  Anyone know the trick?  I always end up blocking myself out of the switch and having to reset it.
My basic problem is trying to connect two SRW224P's with one SFE2000P (in Layer 3 mode).   They need to have the same default or native VLAN for the trunking to work properly.   The SFE2000P has VLAN 100 as default, while the SRW 224P has VLAN 1 as default.
The documentation says I should be able to change it, but never says how.   I haven't found any way to change the VLAN 1 on the SRW224P's to VLAN 100....but I would be willing to that as well.  I have attachment to VLAN 1 or VLAN 100....I just want them to be the same.
Thanks....gerry

Correct. As soon as you change it to 100, you will lose access to the devices since vlan 1 is used for management.  To shorten the down time, you can create vlan 100 and all the SVIs on all switches ahead of time and than change it form 1 to 100 in a maintenance window.
HTH

Similar Messages

  • Change Voice Vlan 100 to other TAG

    Hellos
    I have a switch ESW 520.
    by default this switch have created a voice vlan (vlan 100 Cisco-Voice)
    Can I change the vlan 100 Cisco-Voice to vlan 5 Cisco-Voice??
    if it is possible how to do it?
    Regards

    Voice VLAN — The Voice VLAN field displays the current Voice VLAN used by
    the switch. The default is VLAN #100. This VLAN carries the voice traffic, and is
    also advertised through the CDP to the other elements in the network. The user
    can change the Voice VLAN via this screen.
    http://www.cisco.com/en/US/docs/switches/lan/csbms/esw500/administration/guide/ESW_500_Administration_Guide.pdf
    Page 66

  • Changing native VLAN on non-root bridges

    I have quite a few 1310 Bridges setup in point to multipoint configuration with a root bridge with a sector antenna at the campus network and remote sites connecting in. I have multiple VLANs trunked onto one SSID, this allows for having multiple vlans in use at the remote site. The problem is I want to configure some remote site bridges with a different native vlan than the standard allowing me to plug the client directly into the injector and eliminate the need for a vlan aware switch. I have tried to configure the the "encapsulation dot1q VLAN# native" but this swaps the bridge group on the subinterface to a bridge-group 1 .
    ! Last configuration change at 01:23:08 UTC Tue Sep 15 2009 by Cisco
    ! NVRAM config last updated at 01:23:09 UTC Tue Sep 15 2009 by Cisco
    version 12.4
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    no aaa new-model
    dot11 ssid Cisco-24
    vlan 1
    authentication open
    authentication key-management wpa
    guest-mode
    infrastructure-ssid optional
    wpa-psk ascii test
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    encryption mode ciphers aes-ccm tkip
    encryption vlan 1 mode ciphers aes-ccm tkip
    encryption vlan 901 mode ciphers aes-ccm tkip
    encryption vlan 902 mode ciphers aes-ccm tkip
    encryption vlan 904 mode ciphers aes-ccm tkip
    ssid Cisco-24
    speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0
    station-role non-root bridge
    interface Dot11Radio0.1
    encapsulation dot1Q 1 native
    no ip route-cache
    bridge-group 1
    bridge-group 1 spanning-disabled
    interface Dot11Radio0.901
    encapsulation dot1Q 901
    no ip route-cache
    bridge-group 255
    bridge-group 255 spanning-disabled
    interface Dot11Radio0.902
    encapsulation dot1Q 902
    no ip route-cache
    bridge-group 254
    bridge-group 254 spanning-disabled
    interface Dot11Radio0.904
    encapsulation dot1Q 904
    no ip route-cache
    bridge-group 253
    bridge-group 253 spanning-disabled
    interface FastEthernet0
    no ip address
    no ip route-cache
    hold-queue 80 in
    interface FastEthernet0.1
    encapsulation dot1Q 1 native
    no ip route-cache
    bridge-group 1
    bridge-group 1 spanning-disabled
    interface FastEthernet0.901
    encapsulation dot1Q 901
    no ip route-cache
    bridge-group 255
    bridge-group 255 spanning-disabled
    interface FastEthernet0.902
    encapsulation dot1Q 902
    no ip route-cache
    bridge-group 254
    bridge-group 254 spanning-disabled
    interface FastEthernet0.904
    encapsulation dot1Q 904
    no ip route-cache
    bridge-group 253
    bridge-group 253 spanning-disabled
    interface BVI1
    ip address 10.0.0.100 255.255.255.0
    no ip route-cache
    ip default-gateway 10.0.0.1
    ip http server
    no ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    snmp-server community misdept RO
    bridge 1 route ip
    line con 0
    line vty 0 4
    login local
    end

    Correct. As soon as you change it to 100, you will lose access to the devices since vlan 1 is used for management.  To shorten the down time, you can create vlan 100 and all the SVIs on all switches ahead of time and than change it form 1 to 100 in a maintenance window.
    HTH

  • Changing native vlan on running network

    I want to change the native vlan on running network. a network include 30 switches . there is loop free topology .
    unfortunately native vlan is vlan 1 and also management network .
    in my test environment :
     if I go to a switch and change native vlan from 1 to 100  the stp will Block the link for vlan 1 and i lose my access to the switch and then i should go to other side and change the native vlan to 100.
    i just want to know the best practice for this situation.
    Thanks !

    Correct. As soon as you change it to 100, you will lose access to the devices since vlan 1 is used for management.  To shorten the down time, you can create vlan 100 and all the SVIs on all switches ahead of time and than change it form 1 to 100 in a maintenance window.
    HTH

  • Why on import are Nikon D800 files changed to clarity +100 vibrance +35 ?

    Why on import are Nikon D800 files changed to clarity +100 vibrance +35 ? Preset are set to not change anything. Camera set to vivid LR 5

    It seems to me that either you have a preset involved that you're not aware of, or else somewhere along the line you have inadvertently changed your default settings. Because Lightroom doesn't do that automatically on its own, by default.

  • Changing native vlan

    Is there a good reason to change the default native vlan 1 between two 802.1Q trunks? And is there a rule regarding best practices? thanks.

    With 802.1q trunking, the only significance of the native vlan is the fact that it is not tagged. Most administrators default to vlan 1, but others vary.
    It's discussed in the best practices document, but there's no specific best practice for Native Vlan, as changing it does not have any bearing on network performance or stability. It does talk about the significance of Vlan 1, which may be of interest.
    http://www.cisco.com/en/US/customer/products/hw/switches/ps663/products_tech_note09186a0080094713.shtml
    HTH,
    Bobby

  • CiscoWorks: VLAN creation failed via CM-VLAN Configuration

    Hi,
    I have trying to create VLAN on single switch via CM-VLAN Configuration and getting below message, although switch is configured with correct snmp and I can backup same device via RME and also delopy config to it via Netconfig.
    Please advice. Thanks
    I am using LMS 3.2.1; CM 5.2.2; RME 4.3.2
    Creation of VLAN failed
    "There were some errors during operation."
    Failed to perform the operation on 10.*.*.* Cause:An error occured while performing SNMP operation.
    Action:Examine and save the server log file and report the error to the product administrator for further action.

    The credentials can be changed under Common Services > Device and Credentials > Device Management.  Select the devices and click the Edit Credentials button.  Fill in the correct username and password for these devices.

  • I want to effect a change for about 100 users - basically I want a command-line solution in CentOS. Is there a reasonable way to automatically associate .ica files with /usr/lib/ICAClient/wfica so we don't get prompted by Firefox? TIA.

    I would like to write a script to do this for about a 100 CentOS users. I don't want each of them changing preferences on their browser.

    Hello Oddsbodkin,
    It looks like the creator of Netflix Desktop has a site for the project here:
    https://answers.launchpad.net/netflix-desktop/
    I would try posting your question there and see if anyone else has encountered this error and has a solution.
    Cheers, Patrick

  • IAS not sending VLAN or switch not getting VLAN assignment

    HELP!
    My config looks right but I am unable to assign VLAN dynamically via 802.1x. Attached is my config and debug.

    Your debug output doesn't look quite right. The switch expects a tag number (number 1) to be sent along with the VLAN name, and you'd normally see this in the Radius debug output. For example, yours shows:
    Attribute 81 12 6C61626E
    where 81 is the attribute number, 12 is the length, and 6c61626e is the hex values of the first 4 bytes of the VLAN name (6C=l, 61=a, 62=b, 6E=n, etc) that you're returning.
    What it should look like though is this:
    Attribute 81 11 01544541
    Note the first byte is 01 for tag number 1, then you get the actual VLAN name (54=T, 45=E, 41=A, etc).
    I'm not sure how to set up IAS to return a tag number in attribute 81, check your IAS configuration and see if it can be done. I've known other people to get this working with IAS so it must be possible, I just don't have an IAS server handy that I can check with, sorry.

  • Identify change from over 100 Z todes

    We want to identify the list of Tcodes which are changed between 2010.1.1 to 2011 1.12,  we have total 1000 customized T-codes, somes are ABAP programs, some are report painter, some are forms,can anyone suggest the T-code to use or table to check for this task, thanks

    Hi Jolin,
    Use this way,
    get the custom transactions in SAP from
    TSTC Transaction codes in SAP
    TSTCT Transaction codes texts,
    REPOSRC - Report Source Code
    Use to check The ABAP Report Changed/Created by Date/User.
    As far as I know(Not sure 100%), I think you cannot see when was the transaction was created/changed. Even you cannot see it from SE93 I hope.
    Thanks,
    Dileep .C

  • Change Native Member Range

    How can I change the Native Member Range in the Industrial Automation OPC server. I am trying to the change the range for the GE Versamax from R1-R2028 to R1-R6048.
    Thank for your help in advance.

    It's hard coded, and can't be changed, unless NI release a new version of it and add the range as new features.
    Ryan Shi
    National Instruments

  • 5D III can't change ISO to 100

    i am using a 1 year old 5D III. i never really thought about it, but i assumed i could not shoot a lower ISO than 200.
    but looking at exif data in other photograhers' photosi see ISO of 100.
    i thought cool. because that is what i used mostly on the 7D.
    but i couldn't change the ISO lower than 200. moving the dial the ISO goes from 200 to A.
    so i got out the manual. i know a clever idea. followed the directions on ISO settings. and still, no joy. looked online. same directions. same results. i was desparate so had a nikon friend take a look. same results. nothing lower than 200.
    i am assuming i am missing a step somewhere.
    i shoot RAW without jpg.
    RSG
    Solved!
    Go to Solution.

    If you have High Tone  Priority turn on, you cannot use ISO100. If you shoot RAW, then High Tone Priority is pretty useless, may as well turn it off.
    Weekend Travelers Blog | Eastern Sierra Fall Color Guide

  • KT3 Ultra2-R ... Can't change FSB beyond 100

    Dear all,
    Just got my KT3 Ultra2-R with an Athlon XP2100, upgraded to 5.7 AMI BIOS, worked great, then made some changes to CMOS (forgot which ones), then couldn't boot.
    When I finally booted and went to CMOS setup, it would not let me change the FSB to anything other than 100...that is, no options on the FSB when I hit enter (shrug).
    Now, my system recognizes the CPU as an AMD XP 1500...blah. Tried everything...resetting CMOS with jumper, took out computer battery, replace 350 SmartBlue PSU with 400 Watt PSU, replaced Heatsink/cooler with better one, wiped contacts, nothing...it's not the temps, because my case idles at 29C chassis and 36C CPU temps.  Even reflashed back to BIOS version 5.6, and still no go.
    When I do "performance" settings in CMOS, it will give me 133 FSB, but my system will now be unstable. Weird thing was, before this "event", performance setting put it at 166 FSB :(
    Anyway, my comp isn't dead....it just won't let me change the FSB.  I called up ABS Computers where I bought this, and they said they are not responsible for damage caused from flashing BIOS...blah, whatever.
    I just put out an order for an Asus A7N8X Deluxe motherboard and joined the NForce2 bandwagon, but if someone could give me some insight into what I could do about my motherboard, besides hang it on my wall, I'd certainly appreciate it.
    Here are specs of my system:
    MSI Kt3 Ultra2-R
    Athlon XP2100
    Geforce2 video card
    soundblaster 5.1 Live
    WD 120 Gig and WD 60 Gig
    Liteon CRWD
    Sony DRU-500AX
    Q-Tech Quiet PSU 400 Watts
    Nexus Heatsink/Fan
    Windows XP Home

    Thanks for the reply, but while checking out the other problem with the KT4V / Athlon 2400 Clock Speed Problem (above) who couldn't set his FSB beyond 100, but when he set it the multiplier to 12.5/13, he gets a 20X multiplier when he goes into Fuzzy Logic.
    Well, guess what, I did the same thing (set my CPU multiplier in BIOS to 12.5/13, and lo and behold, I go into fuzzy logic, and my AMD XP 2100 is recognized as an AMD XP2600 running at 2000 megahertz...now someone explain that to me! I even check with SiSandra, and yup, it's seeing a 2000 megahertz processor. I even ran the benchmark tests on SiSandra, and it's on par with that processor.
    However, my FSB is only 100, and thus, my memory benchmarks are about 25% below the norm for my DDR333 RAM chips (i guess because they are synchronized with the FSB, and probably running at 200 then).
    Anyhoo, i'm tired of trouble shooting and figuring out what the hell is going on.  The comp is extremely stable at 2000 megahertz at 100 FSB...don't know what else to do...so installing new motherboard tomorrow and report back later.

  • Sample rate change from 44.100 to 48.000

    Hi Guys,
    I am preparing a sound design file for a film project. the audio files are originally in 44.100. Now, I am preparing the surround mix for the DVD release. For DVD I would need a sample rate of 48.000khz. However, when I change the sample rate from 44.100 to 48.000 in the Project settings, all my audio files seem to be shortened in the arrange and everything sounds as if it was sped up. How can I change the rate to 48000 without the audio files changing?
    thanks

    Man you have to convert the files to 48khz otherwise they will of course sound mickey moused and distorted when played in a 48khz project. You can easily do that in the Bin, batch process all your files and convert them to 48 using the "copy and convert" funtion from the menue. Compressor does the job also...

  • Vlan 1 (Default) from other VLan not accesible

    Hello at all,
    I have configured a Cisco Nexus 5000 as L 3 Core switch and have now the problem when i try to access an access swicht in VLAN 1 from another Vlan or from outside i get no answer. When I connect a PC on a Interface of the access switch everything is working. Did anybody have a idea?
    Matthias

    Hi,
    did you configure the nexus as default gateway on the access switch ?
    Regards
    Alain
    Don't forget to rate helpful posts.

Maybe you are looking for

  • OS 10.4.11 Mail application

    iMac G5 PPC OS 10.4.11, Mail app. Where can I find my Mail Setup? I had lost my Mail setup and I had to phone my provider so he could steer me to redo my Setup. I followed his instructions and was able to reconnect to my mailboxes. However I did not

  • How to display a specific folder item ?

    Hi, Having the item id, how can we display the content of that item in a page/portlet ? Michael

  • Question Pool Manager text not matching question.

    How can this happen?  I'm using Captivate 5 on Windows XP.  In the image below, the text of the question in the pool does not match what it says in the Pool Manager.  Note the highlighted line on the Pool Manager. It says "Type the question here" whi

  • StringBuffer delete (int start, int end) is too slow - HELP!!

    I've traced a performance problem to one line of code: a StringBuffer "delete (int start, int end)" call. My StringBuffer contains a lot of data, maybe 500,000 characters. My code loops, searching for a particular character (the search is fast, btw).

  • Disabling auto-sync, turning on "manually manage songs"

    Just so everyone here knows, I had an iPod mini which I managed manually. I got the new iTunes, and plugged in my ipod. It said it was "updating", and I couldn't figure out how to make it stop. I thought it was going to delete my music and sync it wi