Changing the memory

hi was wondering if its possible to change the memory in my mac pro .
i have 800mhz in there at he moment . but would like to use 1066mhz .
system is 2.8 quad late 2008

There is no Late 2008 MP. There's an Early 2008 and Early 2009. Yours sounds like the former. It does not support using DDR3 nor 1066 MHz RAM. It requires PC2-6400 DDR2 RAM.

Similar Messages

  • Can we change the memory of new Ipad 16 GO to 64 GO ?

    can we change the memory of new Ipad 16 GO to 64 GO ?

    Move some of your documents, pictures and music to the cloud.
    Dropbox
    http://itunes.apple.com/sg/app/dropbox/id327630330?mt=8&ls=1
    Sugarsync
    http://itunes.apple.com/sg/app/sugarsync/id288491637?mt=8&ls=1
    Box.net
    http://itunes.apple.com/sg/app/box-for-iphone-and-ipad/id290853822?mt=8&ls=1

  • I have a iMAC(got it in less than 2 months ago), can I change the memory(upgrade it from 4 GB to 8GB) myself? I mean I need to open the screws and exchange the memory chips. Does it cancel the guarantee?

    I have a iMAC(got it in less than 2 months ago), can I change the memory(upgrade it from 4 GB to 8GB) myself? I mean I need to open the screws and exchange the memory chips. Does it cancel the guarantee?

    No, unless you break something or install the wrong RAM, new RAM is not covered by warranty/AppleCare of course.
    https://support.apple.com/kb/HT3011
    https://discussions.apple.com/docs/DOC-4291

  • HT1750 I tried to change the memory and now my Imac will not power on. and there are no beeps. what did I do wrong?

    I tried to change the memory and now my Imac will not power on. and there are no beeps. what did I do wrong?

    Don't know.  Could be any number of reasons.  Re-read the how to install RAM manual again for your model iMac.  Double & triple check to make sure you purchased the right RAM chips.   Make sure they are seated properly.  If you didn't hear a snap when seated, the RAM is not properly seated. 

  • I changed the memory settings in the KT6V Bios.

    I changed the memory settings in the KT6V Bios without flashing to the latest bios update.  Now the system won't post and of course I learned afterwards you shouldn't mess with memory settings.
    I did everything, cleared the cmos(several times with and without the battery), also tried to do the bios recovery but that didn't work.  And yes I have the 4-pin plugged in, I also tested all the parts on another motherboard and they work fine with it.
    So is the board fubared?  I just bought it the other day, it's a long drive to take it back where I got it from so if anyone knows if there is a possible way to recover it please let me know!

    Quote
    Originally posted by labtech1
    If you are getting four red leds on the dled bracket and the board is making no attempt to post there is little chance that you will be able to recover the bios if you were using a version prior to 1.3. The emergency bios recovery procedure is detailed here:- http://www.msi.com.tw/html/support/bios/note/boot.htm or you can try tapping the F10 key followed by "Y" on the keyboard to see if you can trigger the bios flash recovery procedure that way. It did not work for me. Good luck. Post back with your results.
    Ya I'm getting the four red led's and I've tried everything and still no post.  Geez, I can't believe this, I've never seen a motherboard die by just changing the memory setting from normal to fast...this is quite irritating.

  • What will happen if I change the memory by myself? What will apple do?

    Will they annoy with me? Cause if I buy the memory at other places, it is really cheap

    Nothing it is a user upgradeable part.
    The only thing that will happen is the RAM you put in is not covered by the Apple warranty and if you damage anything inside the computer while you are changing out the RAM that damage won't be covered under the warranty.
    Look in the user manual. Apple give you instruction on how to do it.

  • How to change the memory size of Iphoto to put more pictures??  I don't have no more space!!!

    Hi....
    I wonted to put some more pictures to Iphoto...but I can't do it because it is telling me that I don't have enough space.... I so that memory on the hard disk for Iphoto is only 37gb ... how can I change that?????  I wont to have all my photos in this program!!
    Thank you for your answers...

    I have trued to clean my hard disk --- but this is not the problem!!
    "IPhoto nn può imporate le foto perchè nn c'è abbastanza spazio libero sul VOLUME che contiene la libreria di Iphoto"
    this is the messege how is coming out....
    it means...
    Iphoto can not import the fotos, because there is not enough free space of VOLUME that containse the library of Iphoto
    do you now that could it be???

  • How to change the memory in Lenovo A516?

    Good evening. Please show me how to do ... or that set up that would be saved on the SD application card and not on internal memory ... Whether it is possible to model Lenovo A516? 

    I tried to follow these steps
    http://www.askmefast.com/How_to_move_app_game_to_sd_card_lenovo_a516-qna7899257.html#q5512171
    but when i downloaded link2sd , and tried to move my application in sd card. It requires me to root my phone, which will later on voiding my warranty.. and i got my phone yesterday. and now it's lagging. i also updated my system. now it lags. i don't know what to do. i'm scared of rooting my phone. i only installed a few applications but now my phone hardly works. it turns black on me and i need to long press the power key for the screen to turn on. TT__TT. it's unfortunate to have a defective or i don't know branded phone like this. it's very surprising that my china android phone works much better than my lenovo. 
    Lenovo, please help us solve this problem. i know you're much more better than this. 

  • Is it possible to upgrade or change the memory of your iTouch? Like from 8gb to 32 gb

    My itouch's memory 8gb is not enough for me. I need at least 32 gb do you guys think it can be upgraded or  maybe changed.

    No, if you want more capacity/storage you need to purchase another iPod

  • Change the memory used by de NWDS

    Hi masters.
    Please, how can I change de minimal and maximal memory that NWDS take to itself ?
    My NWDS needs to became more faster.

    You can create a shortcut like
    C:\NWDS7.1\eclipse\SapNetweaverDeveloperStudio.exe
    -vm "C:\Program Files\Java\jdk1.5.0_12\bin\java.exe"
    -data C:\workspaces\NWDS_FrwkDev_stream
    -consolelog
    -showlocation
    -Xmx1200m
    Armin

  • How to upgrade the memory in the Satellite L75-B7270

    I recently purchased this laptop for my son for his school work. It onlyt came with 4GB of memory and says it is upgradable to 16GB of memory. However, I do not know where to install it! This paricular laptop has a smooth bottom except for the battery, There is no secondary cover that I have usually seen on laptops to add/change the memory. So I am assuming that I need to remove(?) some of the screws and take the bottom off?!? If so, which screws? I can find no information anywhere, not even Toshiba support.
    Please help!
    TIA
    Mike
    Solved!
    Go to Solution.

    This laptop is a royal pain in the a$$ to open up (at least the first time).
    1. Remove the battery.
    2. Identify the retaining screw of the DVD drive. With the laptop facing down, identify the side of the laptop where the DVD drive is located.  The screw in question is a few inches inward (toward the center of the laptop) from that location, where unlike the other screws around it (which are embedded inside of holes), this screw is almost flush w/ the laptop cover (hardly recessed).  Once you find it, remove this screw. The DVD drive should then be able to be pulled out (with minial force). Save this screw (and the DVD drive) off to the side separate from the other screws (as this might be one of two screws which are different than the other screws holding the laptop cover).
    3. After removing the DVD drive, locate the WIDE HEADED FLAT (but very short) screw underneath the opening of the the DVD.  (It's obvious to locate/identify this screw).  Remove this screw as well, save it off to the side (separate from the other screws).
    4. Remove EVERY SINGLE other screw you find visible from the laptop cover (there's around 16-18 screws IN TOTAL, including the ones above).  As far as I can tell, all remaining screws are of the same size & type.  Note: Be sure not to miss the screws immediately to the LEFT & RIGHT of the battery compartment  (although no screws are inside the compartment itself.  Also, don't remove the electrical tape in that compartment -- it has no bearing on being able to open up the laptop).
    5. Now comes the "fun" (tough) part: prying the bottom cover off of the laptop base.  Try lifting up on the DVD drive opening (putting your fingers inside the drive opening and lifting UP).  Hopefully you'll see part of the laptop cover start to separate from the base.  If you do, place something underneath that separated area (a thin piece of plastic, like a credit card).  If that doesn't separate the cover from the laptop, use your fingernails to find a spot SOMEWHERE on the laptop where you can begin to separate the cover from the base.
    6. From that separated area, work your way around the entire bottom of the laptop, prying apart the cover. Unfortunately, this requires using some force as it's clipped in VERY tightly.  Pulling (with your fingers) does work, but it could just as easily break some of the clips, so do this at your own risk. (Don't go overboard w/ the amount of force you use). 
    Note: Try and guage the amount of force needed to start separating the cover from the base.  If you fail to remove some screws, and that approximate level of force fails to separate the cover, you may have failed to remove a screw in that area.  Check carefully for screw holes you may have missed the first time around.
    7. Once you've pried apart the cover, the rest of the process is trivial (for RAM replacement).  The pair of RAM sockets are easily exposed & accessible (there's one 4gb chip installed, the 2nd socket is free).  If you want to upgrade to 8gb or 12gb, you need only populate the 2nd socket w/ a 4gb or 8gb chip respectively.  If you want to upgrade to 16gb of RAM, you'll need to remove the 4gb chip and install 8gb chips in both sockets.
    BONUS: The HARD DRIVE is installed using a flexible style frame, but it's wedged in tightly w/ rubber stoppers (which are part of the flexi-frame), making its removal difficult to figure out.  At the TOP, LONG EDGE of the hard drive (the edge that's towards the laptop's interior, not the edge close to laptop's side wall) there's a rubber grip (maybe 1.5 inches long) barely sticking up.  Grab that grip and PULL UP.  The hard drive should start to come up, at which point you can grab it and pull it out of the SATA socket.
    Before pulling out the HD, pay attention to the orientation of the rubber stoppers at the bottom end of the HD (the end opposite the SATA interface).  When you pull out the HD, the stoppers will come out as well (but since they're attached to the flexi-frame, they won't get lost).
    To remove the HD from the flexi-frame, simply pull the sides of the frame from the HD (it shouldn't take too much time to figure this one out). The frame doesn't use screws. It has attached pins that go inside the screw holes located on the sides of the HD.
    Re-assembly:
    a. Place the the laptop cover back onto the laptop base.  Push down.
    b. Go around the entire edge of the laptop, pushing down w/ your fingers to re-apply all of the clips.
    c. Screw in the wide/short flat screw of the optical drive compartment (from STEP #3)
    d. Slide in the optical drive.  Secure it w/ the screw removed in STEP #2.  (When the optical drive is not installed, this screw-hold doesn't have any threads to "catch" the screw).
    e. Screw in all remaining screws
    P.S. If you have to re-open the laptop, it's far less daunting to pry it apart the second time around (as the clips aren't as tight anymore).

  • Transfering recieved files to the memory-card!!!!

    Hi,
    I transfer files/pictures to my E71 via the Bluetooth but have a couple of problems!
    1- If the file is bigger then the available phone memory (max 110 meg!) then i can't transfer! That i understand but does it exist any way to configure the phone to save the recieved files directly to the memory-card?
    2- Those files that do get transfered to the phone, you have to open first before being able to transfer it ti the memory-card! Problem is some times the phone memory is not enough to even open it so you can't open it nor save it on the memory-card!
    3- There seem to be NO "transfer file" option between the phone memory and the card memory!
    Anyone knows something?
    Cheer's

    If you go into Messaging, hit Options, choose Settings and then Other, then you can change the "Memory in use" from phone memory to the memory card. After that all incoming messages will be stored on the memory card.
    You can also use Nokia PC Suite and use its Windows Explorer extension (Nokia Phone Browser) to copy files directly to the memory card also over Bluetooth (without going through Messaging at all).
    Latest PC Suite from here: http://www.nokia.com/pcsuite

  • How to change size memory for an application under Classic ?

    When I ask informations on my OS 9 application under OS X.4.4, I can no more change size memory ! I can no more use my application with Classic... ???

    ROYCH: This is partly guesswork, but I think it may explain why your problem occurs.
    When OS X is controlling your computer (as it always does on a Mini), the file Type and Creator attributes that OS 9 uses to identify different kinds of files are not used. OS X ignores them in files that have them. Files that are only used by OS X don't have them at all. When you create a new application in Classic mode under OS X, those attributes may not be assigned to it, so the new application may not have any.
    But if you copy the new application to a computer running OS 9, and those attributes are missing, the OS 9 computer will have no idea what sort of file it is. OS 9 won't even know it's an application. To prevent that, I'm guessing that OS X somehow builds clues into the file that enable OS 9 to identify it as an application, and to give it the Type attribute APPL. I believe any file in OS 9 that has that Type attribute will display the Memory menu item in its Get Info window — not only in OS 9, but in OS X. So after you copy your compiled application onto a computer running OS 9 and then back onto your Mini, it has the APPL attribute, and the Memory item is available in its Get Info box.
    I have one application, File Buddy, that can (among many other abilities) display and edit the OS 9 Type and Creator attributes of any file while running in OS X. It can be used to assign specific Type and Creator attributes to a file that has none. You could use it to assign the appropriate Type and Creator attributes to your compiled applications while you are running OS X. After you do so, maybe they will display the Memory menu item in their OS X Get Info boxes.
    If this works, File Buddy can apply the same changes in Type and Creator to a whole folder full of files at once. That would be an easy way for you to accomplish the same thing for several compiled applications instantly, without having to copy them to a computer running OS 9.
    I don't create applications, so I can't test this procedure to see whether it works. I will be interested to hear what happens if you experiment with File Buddy.
    But after saying all this, I really have no idea whether the message you're seeing about insufficient memory is meaningful or spurious. You may go through the whole rigmarole of changing the memory allocation for your compiled applications, only to find that doing so still doesn't enable you to open them. I'll be interested to hear whether that's true, too. Good luck.

  • How exactly does the memory in Labview Fpga work

    I am using a PXI 7853 and I for the past few days I have been playing around with using Memory blocks in the FPGA .
    Now I am relatively new to Labview FPGA programming and hence I would be grateful if someone could provide me with clarifications on teh following :
    a) Since I am working on the development host computer when I initialize the Memory with the option of using a Memory initialization VI then how does it exactly happen in the backend .What I mean to ask is , when i change values of memory in the development computer and then compile the FPGA VI into the board ,is it that the Memory information is ported into the FPGA .If this is the case then in what form are the details initially saved in the development computer .
    b) Is it possible for me to use the initialization VI method to change the valuesi n memory while the FPGA VI is running .If not ,then would it make a difference if I stop the VI and then change the values using initialization method .Would that actually reflect on the FPGA or should I have to re compile the FPGA VI every time I change the memory values in the development computer using the 'Initialization VI method ( that is available as an option when we right click on the memory block in the project explorer window )
    I tried testing with simulation for FPGA VI and found that when i try to change the memory values by running the initialization VI . a pop up comes that says that it is not possible as the FPGA VI is still in use .
    Any light on this or guidance with links would be highly appreciated 
    Cheers 
    sbkr
    Solved!
    Go to Solution.

    sbkr wrote:
    a) Since I am working on the development host computer when I initialize the Memory with the option of using a Memory initialization VI then how does it exactly happen in the backend .What I mean to ask is , when i change values of memory in the development computer and then compile the FPGA VI into the board ,is it that the Memory information is ported into the FPGA .If this is the case then in what form are the details initially saved in the development computer .
    When you compile the FPGA VI, it will include the values used to initialize the memory.
    Are you asking what happens if you run the FPGA VI on your development computer, and your FPGA VI writes to the memory block, will the new values be included when you compile the FPGA VI? No, those values will be lost. The values that are included in the bitfile are the values that you used to initialize the memory block, as defined in the memory properties dialog box. The initial values are saved in the LabVIEW project file along with the memory block definition.
    sbkr wrote:
    b) Is it possible for me to use the initialization VI method to change the valuesi n memory while the FPGA VI is running .If not ,then would it make a difference if I stop the VI and then change the values using initialization method .Would that actually reflect on the FPGA or should I have to re compile the FPGA VI every time I change the memory values in the development computer using the 'Initialization VI method ( that is available as an option when we right click on the memory block in the project explorer window )
    You need to recompile the FPGA in order to use new initialization values, because those values are part of the FPGA bitfile.

  • Compress the memory pictures

    Anybody know how to compress memory pictures to more smaller memory?
    For example, a photo is 2 mb then we compress to/whatever the size below than 2 mb.
    Like windows got, we can compress the memory by using paint which we just re-save the photo and so on. Then, the memory become smaller.
    I tried using compress, but it would not be able to change the memory size at all.
    Help me guys, Thanks

    to compress the photos would be causing them to lose image quality as well. This is not recommended to do if you want nice photos. Are you running into space problems because of image size?

Maybe you are looking for