Changing the NAT from Moderate to Open.

When I try to join games on HALO 3, it says that my NAT (network adress translation) is moderate and that it needs to be open. How do I change it? I have a WRT54G router.
Message Edited by lBTl_UnRe3L on 10-08-2007 12:39 PM

You can try opening the ports on routers set up page ,by logging to 192.168.1.1.
Under "applications & gaming" tab ,you will find port forwarding use ports 88 & 3074 .
You have to assign static Ip ,subnet mask ,gateway & DNS nos to Gaming Console .
Also under set up tab ,look for MTU change it to "manual" & size to 1365....also, if you get any more port numbers for the HALO3 , try forwading that as well.
Let me know if these settings work .

Similar Messages

Can i change NAT from moderate to open on WRT160N

I use to play xbox live with a wrt54g and had an open nat now i have a wrt160n and when i test the connection on the xbox it comes up moderate.

Change the MTU size from auto to manual .... & 1500 to 1365 ....
Click save settings ...
Check the NAT settings again ...

Help, Need to change NAT from moderate to open for WRT54GS2

just like to the topic says i used these methods:
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
On the set-up tab change the MTU Size to 1365 and click Save Settings...
Click on "Administration" tab and disable the option UPnP and click Save Settings...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box, click Save Settings once done...
2) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
3)Click on the Status tab and take note of DNS1 and DNS2 Addresses...
4) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
5) Also assign the DNS Addresses on the Xbox, Use DNS1 and DNS2 Addresses you took note off of the router status tab as Primary DNS & Secondary DNS for the xbox...
6) Turn off your modem, router, and Xbox...Wait for a minute...
7) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect... i have firmare 1.0.01. i am using 2 Pluglink 9650 Powerline Ethernet Adapters to connect to my xbox for xbox live. if u need anything else let me know. PLEASE SOMEONE HELP

What device is upstream from the router? If you have a modem that acts as a router as well, then you might have a double NAT problem. It's a well documented problem and can usually be solved by bridging the modem or configuring the router to work as a switch only.

Changing NAT type from moderate to open for PS3 on...

Hello,
Pretty simple really.
I want to be able to change my NAT type from Moderate to Open whilst playing FIFA 12 on the PS3.
I am using a BT Home Hub 2. I have read various posts about Port Forwarding and DMZ but what is the method that will open the NAT type indefinitely. I have read that it can only be altered temporarily due to the Home Hub updating it's settings periodically and re-enabling the firewall.
Any help or pointers in the right direction would be greatly appreciated.
Matt

Hi Matt,
Welcome to the forum and thanks for posting. Take a look here for some information on port forwarding. I've also found this whcih you might find useful. Let me know if it helps.
Cheers
David
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

Hey i have a iphone 4s 64gb but and using the internet share .. how can i change the nat type from strict to open please help me :)

hey i have a iphone 4s 64gb but and using the internet share .. how can i change the nat type from strict to open please help me

You will have to configure that with your router. Type your router's IP address in the search/domain bar and allow port forwarding.
What is requiring you to have an open NAT? That issue is usually for gaming consoles, etc.

When I right click on a link "Open link in new tab" since a few days, it "jumps over" the tab to the right and opens in the tab next to that. How can I change this back to opening in the tab next to the page from which I opened as it used to be?

When I right click on a link "Open link in new tab" since a few days, it "jumps over" the tab to the right and opens in the tab next to that. How can I change this back to opening in the tab next to the page from which I opened as it used to be?

Start Firefox in [[Safe Mode]] to check if one of the add-ons is causing the problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
* Don't make any changes on the Safe mode start window.
See:
* [[Troubleshooting extensions and themes]]
* [[Troubleshooting plugins]]
If it does work in Safe-mode then disable all extensions and then try to find which is causing it by enabling one at a time until the problem reappears.
* Use "Disable all add-ons" on the [[Safe mode]] start window to disable all extensions.
* Close and restart Firefox after each change via "File > Exit" (Mac: "Firefox > Quit"; Linux: "File > Quit")

How do I change the default from CS6 to Photoshop CC when I open a photo from Bridge CC?

How do I change the default from CS6 to Photoshop CC when I open a photo from Bridge CC?

Thank you. That works when I double click a RAW image, (opens in ACR then when I open from there it goes to CC) but when I double click a jpg it goes straight to CS6. I'm hoping there is a way to change the default, but haven't found yet. I don't want to remove CS6.

Months ago I opened an account at Argentina store. Recently I moved back to my born country, Brazil. How I need to proceed to change the country from Argentina to Brazil, keeping my ID, password and not lose my purchased content?

Months ago I opened an account at Argentina store. Recently I moved back to my born country, Brazil. How I need to proceed to change the country from Argentina to Brazil, keeping my ID, password and not lose my purchased content? I share the content with my iPhone4, my iPad2 and all sync with my MacPro

Also see http://support.apple.com/kb/TS3998

When I am open file with adobe Pro and reader the resolution in my computer failing, change the resolution from 1920x1200 to 800x600. my video card is nvidia quadro 2000. w7 & 32 bits

when I am open file with adobe Pro and reader the resolution in my computer failing, change the resolution from 1920x1200 to 800x600. my video card is nvidia quadro 2000. w7 & 32 bits

Hi fabiangs,
I'm not sure that I follow. Are you saying that when you open a PDF file in Acrobat or Reader, that the display resolution changes automatically on your system?
What version of Acrobat/Reader are you using? Do you see this same issue in other files/applications?
I look forward to hearing back from you.
Best,
Sara

How to Change the NAT Type of an Apple Router

My dad just bought an apple Router and some new modem. now since i know the router is apple company i want someone to tell me how i change its NAT Type from Strict to either Moderate or Open because its preventing me from connecting to my friends on xbox live. Im also using a Macbook Pro for a computer so its apple software an their shouldnt be any reason this cant be resolved effectively i just need a guide to tell me how to go about fixing this problem.

Unfortunately, the AirPorts are not listed as Xbox Live-compatible routers ... so there is no guarantee doing this will get Open NAT status for Xbox Live!
The following web blog does a great job explaining the NAT issues with Xbox Live! Basically what it comes down to is that although you can get an Internet connection for the Xbox with the AirPorts, you may not get the necessary NAT setting (Moderate or Open) for the Xbox Live! on-line game that you want to play. As such, you basically have two options: 1) Create a DMZ (Apple calls this a Default Host) for the XBox or 2) Configure the AirPort for Port mapping to open the required ports to allow Xbox Live! access ... or 3) Use a compatible router.
Option 1 - Create a DMZ
AirPort Utility > Select the AEBSn > Manual Setup > Internet > NAT
Enable default host at: <Enter the IP Address for the XBox>
Option 2 - Configure Port Mapping
The following ports must be available for Xbox Live to operate correctly:
UDP 88
UDP 3074
TCP 3074
To setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the Xbox 360.
AirPort Utility > Select the AEBSn > Manual Setup > Internet > DHCP tab
Click the "+" (Add) button to enter DHCP Reservations.
Description: <enter the desired description of the host device>
Reserve address by: MAC Address
Click Continue.
MAC Address: <Enter the MAC hardware address of the Xbox or the MAC address of the wireless depending on how you connect the XBox to the network.>
IPv4 Address: <enter the desired Private IP address>
Click Done.
2. Setup Port Mapping on the AEBSn.
AirPort Utility > Select the AEBSn > Manual Setup > Internet > NAT > Configure Port Mappings
Click the "+" (Add) button
Service: <choose the appropriate service from the Service pop-up menu>
Public UDP Port(s): 88, 3074
Public TCP Port(s): 3074
Private IP Address: <enter the DHCP Reserved IP address for the Xbox you created earlier>
Private UDP Port(s): 88, 3074
Private TCP Port(s): 3074
Click "Continue"

How do you change the weather from Fahrenheit to Celsius in iPhoto for iOS?

I have been trying to change the weather from fahrenheit to celsius and I cannot seem to find out how. Can anyone help?

I had the same thing happening after upgrading to IOS 7.
I clicked on the weather notification which opened a new tab
https://www.dropbox.com/s/sai5kn3xufrqngd/IMG_0013.PNG
I just had to click on the °C to get the Celsius displayed both in the app and the notification.
Maybe a reboot would help ?

Is it possible to change the costing from moving average to standard??

hey all,
i wana know is it possible to change the costing from moving average to standard or vice-versa in the item master??
cheers

Hi Satish
Please look at the documentation from SAP for using this function. I just looked on my drive and can't find the document I used to have for this.
Just setting quantities to zero will not work as all open P/O, S/O, etc must also be closed before you can run the Inventory Valuation Method function. This is all detailed in the document.
I have done this successfully before for a client with over 4000 items, so I have been through the process. Please let me know if you need assistance.
Kind regards
Peter Juby

How to stop the executable from starting when opened

Hi Guys,
I am building an exe with the application builder. I am not able to find a way to stop the exe from running when opened. I dont need the exe to run. I know I m missing a very basic step here but I m not able to do that.
Could anyone explain me how to do this.
Regards,
Nitin

Hello,
This is Dominic L. from Applications Engineering at National Instruments. This was reported to R&D (CAR#41DAPUQU) and was fixed in LabVIEW 8.2.1. Here is a link to the current evaluation software download for LabVIEW:
http://digital.ni.com/demo.nsf/websearch/14f9ce475127ade786256ac60070926c?opendocument
This particular bug actually renders all the build options for source file settings unusable. While the other options can be set manually in the source VI properties, the start-up VI will always run when an executable is opened.
Here are three different workarounds to this:
Option 1 - Upgrade to 8.2.1.
Option 2 - Check "Enable debugging" and "Wait for debugger on launch" in the Advanced page of the build specification. One side effect is this will include the block diagrams of the VIs and extra code for debug tool support. Note that if you don't protect the source code (block diagram), it kind of defeats the purpose of creating an executable.
Option 3 - Use a dummy startup VI to launch the desired startup VI.
For the third workaround, the attached "Dummy Startup VI.vi" uses VI server to open the desired startup VI's front panel and then closes. To use the Dummy Startup VI follow these steps:
Add the Dummy Startup VI to the project.
Open the Dummy Startup VI and change "Main VI.vi" to the VI you would like to open but not run in the project and save.
In the source files page of the build, select the Dummy Startup VI as a startup VI and the VI you would like to open but not run as a support VI.
Build and run.
I hope this helps.
Have a great evening!
Best Regards,
Dominic L.
Attachments:
Dummy Startup VI.vi ‏12 KB

I'm trying to buy CC Photoshop/Lightroom packages. In order to complete payment, I need to change the country from the default options (United States) to Brazil, But I'm not allowed to do it. I've already changed my origin country in my account informatio

I'm trying to buy CC Photoshop/Lightroom packages. In order to complete payment, I need to change the country from the default options (United States) to Brazil, But I'm not allowed to do it. I've already changed my origin country in my account information.How do I change the country in order to complete payment?

These are the two links I have
Change/Verify Account https://forums.adobe.com/thread/1465499 may help
-http://helpx.adobe.com/x-productkb/policy-pricing/change-country-associated-with-adobe-id. html
If the above doesn't help, you will have to contact Adobe (this is an open forum, not Adobe support)
Adobe contact information - http://helpx.adobe.com/contact.html
-Select your product and what you need help with
-Click on the blue box "Still need help? Contact us"

Can logic express slow down or change the key from playbacks like the program "Amazing slowdowner"?r

Hello,
I'm a new member and I'm actually trying to work with garage band to record voice and playback. Can "logic express" Vs. 8.0 slow down or change the key from playbacks like the program "Amazing slowdowner"? This is a programm wich costs 50 US Dollar and I want to decide if i buy it or not.
What is the hgreatest different between "garage band" and logic express 8.0? Who can hepl me, which is the right thing for me. I find it difficult to find out which effects are the best only to record my voice with playback.
Thanks for your advices.

If you want to slow down the audio why not download a program from ABRSM called Speedshifter- its free and is very good. you could export the audio from Logic and open the MP3 file with speed shifter. I think speedshifter may also have the ability to alter the pitch as well. I use it for Flute practice- its very useful !

Changing the NAT from Moderate to Open.

Similar Messages

Maybe you are looking for