Changing the radio channel on Airport Express

I have set up a network in my house using an airport extreme which is connected to the ethernet. Then I added an airport express to extend the network upstairs. That all worked well but we did not get a good signal in our bedroom. I then bought a second airport express and added that. My computers can see the new express but it does not seem expand the network. I have done quite a bit of reading and the only thing I can see is that I maybe need to change the radio channel of the second express. However I only get the option of changing radio channels on the airport extreme base station. Am I missing something?

When you setup the Airport Express(n) to "extend a wireless network", it extends the exact same settings as the main network. So, the Radio Mode, Security, Password and Channel will all be the same.
It's not possible to separately change the channel on the Express set to "extend".
You might want to experiment with the placement of the Express devices that you have set to extend by moving them closer (or possibly, further) away from the main AirPort Extreme.

Similar Messages

Changing the radio channel on Airport Express used to extend an Airport network?

Hi,
I'm using a Time Capsule as my primary wifi base station and an Airport Express to extend the network. The two devices are connected by WiFi.
My problem is that the 5GHz network of the Airport Express is using channel 100 and the reception just 5 meters away from it is everythign but great. According to Apple WiFI diagnostics I should use on of the low intensity channel like e.g. 36, 40.
My problem is that I dont know how to change the channel. Using Aiport Utilities there is no option to select the radio channe in the options for the wireless network. Is this not possible at all?
Thanks a lot for your help!

What model is the TC?
If you are extending the TC by wireless then the channel must be set on the TC not the Express.
Go to the wireless tab of the airport utility and select wireless options. Channels are there.
But if you have the new AC model the channel will not change for 5ghz.. you will not be able to adjust it even if you change the numbers..
You really should use 2.4ghz for areas where signal is bad.. it is still much better than 5ghz.

How can I change the base station my airport express connects to?

I just added a new AirportExpress to my wireless network and am using it to extend the range of the network and for AirPlay. When setting it up I selected the main base station that provides the wireless network when asked to select a device for it to connect to. However, now when I view it in Airport Utility, it's the only device on the network that has only Good signal strength rather than Excellent. There is another AirportExpress conencted which has Excellent signal strength that is the closest access point to this new AirportExpress.
How can I change the setup using Airport Utility so that that's the device that it's using to connect to the network?

With a Mac using the Airport Utility.
With a PC using the Airport Utility you can install on your PC with the install disc included.

Hi. Does anyone know ifs it possible to play Spotify on the IPhone through both Airport Express and Apple TV? Whenever I click either/or it just changes the speakers rather play through both? Cheers

Hi.
Does anyone know ifs it possible to play Spotify on the IPhone through both Airport Express and Apple TV?
Whenever I click either/or it just changes the speakers rather play through both?
Cheers

to transfer audio to an airport express the device needs to support airplay unless your samsung tv's manual clearly state it does support it then it don't
appletv can't get audio input into it the optical connector is output only same with the hdmi port

An error occurred while connecting to the AirPlay device "Stereo Airport Express G". The network connection failed.

When attempting to play iTunes 11.1.2 music wirelessly from my Mac Mini to stereo speakers connected to an AE "G" I get the following message: An error occurred while connecting to the AirPlay device “Stereo Airport Express G”. However, when I attempt to play internet radio from an iPod Touch wirelessly to the same speakers connected to the same AE "G", it works fine.
Finally, when I swap out the "G" for an AE "N" connected to the same speakers Airplay works fine, both from the Mini and the iPod.
Why would the iPod connection work while the Mini connection not?

I have what sounds like a very similar issue.
I had my Denon 3312ci working perfectly with Airplay from my 2013 iMac running iTunes. Upgraded to iTunes 11.1.3, and now when I attempt to Airplay direct from iTunes to the 3312, it plays for about half a second and then stops. Displayed on the Amp then says "Assigning Network". The amp starts dropping ping packets at this point. About 15-20 seconds later the pings start coming back, but no Airplay.
I tried different network cables, resetting the microprocessor, a different switch, changing between DHCP and static IP. Was about to make a warranty call to Denon, when I thought maybe I should try Airplaying directly from iphone and ipad. Much to my surprise, it worked from those devices.
I prefer to use my iMac to Airplay rather than ipad/iphone as I found I got next to no audio drop outs using it that way (they are both using wired network), where as ipad/iphone occasionally would get a moment of silence in the middle of a song.
My network set up is fine. I can use internet radio and connect to DLNA services fine on the amp. It is just airplay between iTunes 11.1.3 and the amp where the issue lies.
No fixes as yet, but I have logged a support call with Denon Australia to see what they say.

How to connect grace digital wifi radio receiver to airport express.

Hi,
I need to connect grace digital wifi radio receiver to airport express. The receiver works fine with belkin n150, however when connected to express as primary base station ( belkin switch off), it displays
"Default gateway.......
Port 80 not found. not connected"
The conneted type is dynamic wifi network (POE + ). The express is set in bridge mode and configured through ipad.

Hi,
Called up the apple support services on Dec 9, 2013 and was on line for almost 1 hour without a solution. However, received a call back from team in Singapore on the same day and commitment to revert on the issue within 24 hrs. Received a call within 24 hrs and the entire discussion came down to the point that I have to manually set the grace digital equipment.
I tried other options and eventually the simplest thing to do was to set the connection option to DHCP only and ignore the error.
Now its working fine..

HT201335 I want to watch an iTunes rental video on my MacBook Pro but stream the sound to my Airport Express linked speakers. However re Airplay icon doesn't show up in iTunes when playing the rental video. Is there a way around that?

I want to watch an iTunes rental video on my MacBook Pro but AirPlay the audio to my AirPort Express linked speakers. However the AirPlay icon isn't available when arching the rental video in iTunes. Is there another way? Do I need to but an AppleTV? I don't own a TV, hence why I want to watch on my MacBook Pro.

Welcome to the Apple Community.
With or without an Apple TV you can't send video to one device and audio to another using AirPlay.

How on earth could I be connecting to the Internet through my airport express when it is not connected to anything?

I'm not entirely displeased with the situation but I cannot see how I could be connecting to the Internet through my airport express when the Airport is not connected to anything.
Weird huh?
I have a separate non- Airport wireless network connected to the Internet. I had previously set-up the Airport to link with this network but disconnected it (by resetting it) as music streaming was unlistenable due to frequent drop out. I now just have the Airport Express as a standalone wireless network only connecting to the stereo to stream music from devices.
My devices are only connected to the Airport network with cellular data off. Yet I can still connect to the Internet AND listen to streaming music (without drop-out no less).
I don't want to fix it but I would like to know how the frag it could happen so i don't screw it up accidentally.

I would say you still have something of the previous setup.
To be sure you don't mess up, save the configuration.. go to the top menu area of the airport utility and export configuration.. which will land on your computer.
Now you can recover at anytime to the current setup.
How it works.. that is magical ..
Open the airport utility.. edit.. and take a screenshot and post it of the following pages..
Internet wireless network
THen we can tell you how it is working.

I have an Ipad and Iphone but I don't have an Airprint, only a WIFI printer,my question is if I connect the wifi printer to Airport express, can I print from Ipad and Iphone ?

I have an Ipad and Iphone but I don't have an Airprint at home but only a WIFI printer, my question is if I connect the wifi printer to Airport express, can I print from Ipad and Iphone ? Please help me if anyone knows about this.

Unfortunately, connecting a non-AirPrint-enabled printer to an AirPort base station's USB port will not make it AirPrint-ready.
You will need to use another solution, like Printopia, to be able to print to this printer from an iOS device.

I have installed Airport Extreme on my iMac, but want to extend the wireless network with Airport Express. Everything is fine until I try to select Extend the wireless network. I select Extend Wireless network but have no success. Ideas?

I have installed Airport Extreme on my iMac, but want to extend the wireless to rooms with a weak signal. The internet connection is fine with the basic setup. As soon as I go into Airport Utility to select Extend Wireless Network and fill in what I believe is proper information, I get an error message that Airport Extreme no longer has an IP address, the internet connection is broken, and under Wireless, that there is a wireless network in existence that can't be found. Rebooting the modem only brings the Airport Extreme back to the starting gate so that the internet is once again available. I assumed (naively) that with the All Mac All-the-Time context, adding Airport Express would truly be Plug and Play. I got the plug, but no play. I asked a Comcast technical specialist about it and he said that I needed to reset the Airport Express settings back to their default, factory status. I looked that process up online and found out that the way to do that was to hold down the reset button, then plug Airport Express into the socket and wait for the green light to flash four times. Then wait 45 seconds and the default settings will return. I did all that, only to find out that after the initial flash of green, green never appeared again. I got a fast flashing yellow light, followed by the light going off. Apparently this didn't reset it properly. So, after hours trying to get this system to work, I appeal to someone who can see through this mess and provide the key to success!
highFly376

Let's see if I can get this straight.
You have an Airport Extreme base station that is set to "Create a wireless network" and you have the box checked for "allow this network to be extended"....
Then you have an Airport Express that is set to "Extend a wireless network" which you selected the name of your network in the box...
Correct?
See this Apple document:
http://support.apple.com/kb/HT4259?viewlocale=en_US&locale=en_US
The wireless unit on the right of the diagram can be either of the newer Apple base stations.
Extreme, Express, Time Capsule

Can you share a USB hard drive over the network through an Airport Express?

After asking a few individuals at my local Apple Store, I have been consistantly told that I can plug in a usb hard drive into the bottom of my airport express and share it over the network.
However, after making sure my airport express has the latest firmware (6.3) and even donwloading and installing the airport disk utility I still am not having any luck getting my HFS (journaled) usb 2.0 hard drive to be visible on the network.
I have also noticed that when following the instructions on this apple support document (http://docs.info.apple.com/article.html?path=AirportUtility/5.1/en/ap2108.html) that when I get to step 3, the option to click disks is grayed out. I assume this supports my theory that the airport express won't share hard drives, can anyone confirm?
Am I doing something wrong? Or were the reps at my store mistaken and the only hardware that can share a hard drive is the airport extreme not express?
Thanks
Message was edited by: althe3rd

Thanks for the swift reply.
Continuing my investigation I started to come to the conclusion you just mentioned. I am surprised none of the staff at my store realized this. However, at least I know now.
The basis for me looking to this is... With leopard on the eve of its release, I wanted to get a large network accessible storage solution that would allow my wife's and I's Macbook pros to use time machine on the network drive when we were at home. Since we rarely use our laptops while sitting at a desk connected to an external drive, I figured this would be a great idea and started to look into various NAS solutions.
Surprisingly, most generic (netgear, western digital) network drives require you use proprietary software to connect to them, and are only compatible with windows xp. After seeing the options the airport extreme opens up in terms of network storage I figured it would be the best bet.
Do you have any other suggestions besides getting an airport extreme? I would rather not have to buy a full blown mac that I have to leave on 24/7 to share the drives. Or do you see any possible pitfalls to this idea? Such as, would time machine forget to use the network drive after a while since it wouldn't always be available to it when away from home?

The network on my airport express works, have wifi on the ipods,etc. But when I open airport utility on my mac and on the iphone nothing exists. Why?

The network on my airport express works, have wifi on the ipods,etc. But when I open airport utility on my mac and on the iphone nothing exists. Why?

Reboot the modem. Just pull the power for a few seconds. No settings are lost. The laptop getting through to the internet is not relevent.

Can I choose not to broadcast the name of my AirPort Express?

I would like to know if I can keep the name of my AirPort Express from being broadcast to other computers. On my old Netgear router I could choose to not broadcast the name but, I don't seem to see the option in the AirPort Base Station Utility.
PowerBook G4 12 SuperDrive Mac OS X (10.3.9)

A closed network is still broadcasting and still broadcasts the network name.
A casual user won't be able to see the network from their computer.
However anyone with easily obtained software will be able to see it just fine from their computer.
Unfortunately "Closed" networks, MAC access control lists, and reduction in transmission power are all more "feel good" security rather than real security. All these various approaches are dated and mistakenly lead to overconfidence.
WPA is your friend if you value wireless security.

What is the approximate range of Airport Express for iPad2?

What is the approximate range for Airport Express to use with iPad2?

Clearly the range is impacted by the walls in the transmission path. However, I was able to get about sixty feet. As this was no different than that with my Westell-7500 modem/router ("g" standard) from Verizon, I returned the Express.

How do you change the midi channels of a region?

Lets say i have a region recorded on midi channel 1, how do I change the notes to be midi channel 2? Thanks

Depends.
First of all, are you talking about a MIDI region or an Audio region (Audio regions can "be on a MIDI channel", so to speak, if they contain controllers, i.e., volume, pan, etc.).
So let's say you're talking about MIDI regions for now.
The first order of business is to recognize that the actual channel of the MIDI events contained in the region is determined primarily by the MIDI channel that your controller is sending on. For simplicity sake, let's say your controller sends on channel 1, and the track you're recording on is set to play MySynth on channel 1.
If you're wanting to change the channel from 1 to 2, chances are you want to do this to assign this part to play a different sound on a multi-timbral synth. Let's say that the MySynth object -- as seen in the Environment -- is indeed a multi-timbral synth. If the synth selected for that track is currently assigned to play MySynth 1 (i.e., channel 1), just change it to MySynth 2 (from the track's menu).
Now, if you opened the Event Editor, you'd see that the channel of the MIDI data is still on channel 1! This is normal. Logic is able to "channelize" the data when you select a destination instrument that is on a different MIDI channel from the one that the data was recorded on. So if your track is now set to play MySynth 2, you can go into the Event Editor all day and change the MIDI channel of the data, but it will still be channelized to channel 2 because that track is assigned to play MySynth on channel 2.
There are many many reasons why you might still want to change the MIDI channel of the data in the Event Editor despite the channelizing that goes on. But without going into a whole shpiel about these kinds of applications, just know that the primary way to change the MIDI channel is to select an instrument on the desired MIDI channel.

Changing the radio channel on Airport Express

Similar Messages

Maybe you are looking for