Changing UOM and activity in routing

Dear All,
we have defined an activity compressed air with uom FT3 in routing. Compressor are runned on electricity. The power bill is being received for kwh. Now the management wants to change the uom to kwh and subsequently the quantity also.
Now the problem is there are approx. 5000 FG materials where the change is required to be done.
Please give suggestions how to achieve this.
I understand that in CUNI we can develop the conversion factor from FT3 to KWH. Any other workaround available.
Regards,
Divraj

Hi,
Try with CEWB (Engineering Workbench) where you need to select Working Area SAP_OPERATION Focus: Operation where you will get Operations Overview screen in mass.
Hope this helps.
Regards,
Tejas

Similar Messages

Difference between Delta "Change Log" and "Active Table (Without Archive)"?

In BI7.0 environment, we perform our Delta loads (the DTP settings under the Extraction tab, there is a field called Extraction Mode and it's value is selected as "Delta") every day among all our DSOs.
There is a section called "Delta Init. Extraction From..." under the same tab in DTP, there are four radio buttons:
Active Table (With Archive)
Active Table (Without Archive)
Archive (Full Extraction Only)
Change Log
Then what is the difference between "Change Log" and "Active Table (Without Archive)" if both Extraction Mode is "Delta" for two Delta loads?
Thanks!

Hi ,
The new options SP16 has are:(Chk Note 1096771)
Active Table (with Archive)
The data is read from the active table and from the archive or from a near-line storage if one exists. You can choose this option even if there is no active data archiving process yet for the DataStore object.
Active Table (Without Archive)
The data is only read from the active table. If there is data in the archive or in a near-line storage at the time of extraction, this data is not extracted.
Archive (Only Full Extraction)
The data is only read from the archive or from a near-line storage. Data is not extracted from the active table.
Change Log
The data is read from the change log of the DataStore object.
Delta will always be picked from change log table.Only during intialization you can choose between getting data from change log or active table.If you are doing the load first time and are initializzing delta in subsequent data targets, then pulling data from active table will get lesse volume of data then it would have got from change log table....All subsequent deltas will be picked up from the change log. And when we need to reload data into the data target (which would be a full load) - we use active table.
From change log : you can take below ones as targets
1) Cube 2) DSO with Addition as the update for the Keyfigures
From Active table: you can take below ones as targets
1) Cube ,if and only if, the records are never changes in the source once after creation
2) DSO with Addition as the update for the Keyfigures ,if and only if, the records are never changes in the source once after creation
3) DSO with Overwrite as the update for the Keyfigures ( incase deletions is not happening in the source system)
Pls check this link
http://help.sap.com/saphelp_nw70ehp1/helpdata/en/47/e8c56ecd313c86e10000000a42189c/frameset.htm
Regards,
CSM Reddy

Requisition Import changing UOM and quantity when AUTOSOURCE_FLAG ='Y'

I am loading PO_REQUISITIONS_INTERFACE_ALL with the information for my requisition. I give the UOM_CODE as EA and quantity as 20 and it is changing the quantity to .06667 and the UOM to CA. We have three lines in the QUOTATIONS for this item. The first has CA as unit of measure, the second has EA as unit of measure and the third has BG as unit of measure.
I tried unapproving the first line since it appears that Oracle is using the first quotation line to convert. But when I rerun, it doesn't select EA which would be the next quotation line, but rather it selects BG as the UOM.
Has anyone else ever seen this behavior before? I am passing the correct quotation line in AUTOSOURCE_DOC_HEADER_ID and AUTOSOURCE_DOC_LINE_NUM yet Oracle ignores this and seemingly insists on using everything BUT the correct one.
Has anyone else seen this behavior? Is this a configuration setting or am I not filling out PO_REQUISITIONS_INTERFACE_ALL properly?

This was fixed by a patch.

Can't connect wifi after change channel and mode in router

I have a problem with wifi connection. I've been using arch linux for awhile now and my wireless connection is worked well until I setting my router via browser. I change my router channel from 6 to 1 and wireless mode to 802.11n. Usually in windows it will disconnected for awhile then it will connected again, but with arch linux its just disconnected and can't connect anymore. My AP's name before is "olympian hermes", but now it change to "olympian+hermes". in my router setting the name doesn't change (still: olympian hermes).
I've using windows to test if there is problem with my router but it's worked fine in windows. After that i'm using my android phone to make a wifi, but it still didn't work with another network.
I hope someone could help me, thanks in advance.
Here is my journalnetcl -xn output:
Sep 08 07:30:46 arch network[2233]: Starting network profile 'wlp5s0-olympianxa0hermes'...
Sep 08 07:30:46 arch kernel: IPv6: ADDRCONF(NETDEV_UP): wlp5s0: link is not ready
Sep 08 07:31:02 arch network[2233]: WPA association/authentication failed for interface 'wlp5s0'
Sep 08 07:31:02 arch network[2233]: Failed to bring the network up for profile 'wlp5s0-olympianxa0hermes'
Sep 08 07:31:02 arch systemd[1]: netctl@wlp5s0\x2dolympianxa0hermes.service: main process exited, code=exited, status=1/FAILURE
Sep 08 07:31:02 arch systemd[1]: Failed to start Networking for netctl profile wlp5s0-olympianxa0hermes.
-- Subject: Unit netctl@wlp5s0\x2dolympianxa0hermes.service has failed
-- Defined-By: systemd
-- Support: http://lists.freedesktop.org/mailman/listinfo/systemd-devel
-- Documentation: http://www.freedesktop.org/wiki/Software/systemd/catalog/be02cf6855d2428ba40df7e9d022f03d
-- Unit netctl@wlp5s0\x2dolympianxa0hermes.service has failed.
-- The result is failed.
Sep 08 07:31:02 arch systemd[1]: Unit netctl@wlp5s0\x2dolympianxa0hermes.service entered failed state.
Sep 08 07:31:03 arch sudo[2168]: pam_unix(sudo:session): session closed for user root
Sep 08 07:31:11 arch sudo[2716]: wenhui : TTY=pts/0 ; PWD=/home/wenhui ; USER=root ; COMMAND=/usr/bin/journalctl -xn
Sep 08 07:31:11 arch sudo[2716]: pam_unix(sudo:session): session opened for user root by wenhui(uid=0)
Last edited by hermesolympian (2013-09-08 06:43:09)

uhhh theres somthing(s) screwy in your post or maybe its just my screwy brane(quite possible)
go over the wiki line by linehttps://wiki.archlinux.org/index.php/Netctl
be precise and good luck!

Change Number and Process Route

Hi Experts,
I have seen in the Change Master Web-UI is a register for Process Route.
When I'm trying to create a Process Route, the Activities are missing.
Where is the customizing to set Process Route Activities for the Change Master?
And where is the customizing to create the event to start the Process Route?
I have allready done some customizing for the SAP Case Management and the Engineering Record.
I hope you can help me.
Regards,
Thomas

To customize process route to the change number in the Web-UI the following steps has to be done:
Create Activities
To create activities use TA SRMCUSTOMIZING: Records Management --> Customizing for Process Route --> Create or Change Activities and Activity Functions
Create new entries depending on ECN_DIS
Define Activities for GOS-Objects
To define activities for GOS-Objects use TA SPRO: SAP Customizing Implementation Guide --> Logistics - General --> Product Lifecycle Management (PLM) --> PLM Web User Interface --> Objects in PLM Web UI --> Process Route --> Define Activities for GOS Objects for Process Routes
Create new entries depending on the activities created before and for the Object Type PLM_ECN
Check Agent Assignment for all created Standard Tasks
Now it is prossilbe to add steps to the process route to a change number.
To start the workflow the following steps has to be done:
Define Type Linkages for Workflow
TA SWETYPV - Type linkages:
Create an entry if not existing
Object Category: CL
Object Type: /PLMB/CL_PROCESS_ROUTING_WF_BO
Event: START_WORKFLOW
Receiver Type: WS00100012
Receicer Function Module: SWW_WI_CREATE_VIA_EVENT_IBF
Linkage Activated: X
Behavior Upon Error Feedback: 3 - Do not change linkage
Define Instance Linkages for Workflow
TA SWEINST - Instance linkages:
Create an entry if not existing
Object Category: CL
Object Type: /PLMB/CL_PROCESS_ROUTING_WF_BO
Event: STOP_WORKFLOW
Receiver Type: WS00100012
Receicer Function Module: SWW_WI_COMP_EVENT_RECEIVE_IBF
Linkage Activated: X
Behavior Upon Error Feedback: 3 - Do not change linkage
Thanks for your help
Regards,
Thomas

Change UoM of on routing operations.

Hi PP Experts,
Please someone help me on my problem regarding changing UoM on routing operation. I have to change or convert the labor time and machine time from CTS (cents of second) to S(second). How can i change that and i have to consider the impact on report such as routing check, standard time checking report and finacial cost.
Thanks for your help.
Edited by: yatch0325 on Oct 13, 2010 7:58 AM

Hi,
1. In the routing change the UOM for standard value to S and eneter the calculated machine time in S.
2.Change the Base qty and the operation unit.
3.Activity type and the cost needs to be checked.
Thanks,
nandha
Edited by: S.Nandakumar on Oct 13, 2010 8:25 AM

My boyfriend knew my apple id and my password and when we broke up he changed it and he changed my alternate e-mail address so i cannot restore it. The problem is that my iPhone activation is linked to iCloud. What can i do? I have old pass and e-mai

My boyfriend knew my apple id and my password and when we broke up he changed it and he changed my alternate e-mail address so i cannot restore it. The problem is that my iPhone activation is linked to iCloud. What can i do? I have old password and old alternate e-mail.

Take it and its purchase receipt to a physical Apple Store and/or click here and contact Apple's Account Security team.
(124839)

We installed a new router and changed the name of the router. Now my HP C4500 printer won't print.

Our cable company installed a new wireless router and changed the name of the router. Now my HP C4500 printer won't print from my laptop.
I can't find any ot the Set Up stuff I used initially.
Is there any way to get my printer to work again...wirelessly?

Get the latest software for your printer from the "Support & Drivers" link at the top of this page. When you start the installation it will ask what kind of installation you would like. Choose "Wireless" or "Network" then click "Next".
Eventually it will ask you to plug in a USB cable to the printer temporarily to communicate the new router's info to the printer. Make sure to not plug in the USB until it asks.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

My ipad air was bought and activated AFTER September 1st and I downloaded pages, keynote and numbers. I then changed my Apple ID as the password no longer worked, these apps were also deleted I order to be updated. Now I cannot get the free version. Help?

My ipad air was bought and activated AFTER September 1st (activated December 25th) and I downloaded pages, keynote and numbers. I then changed my Apple ID as the password no longer worked, These apps had to be deleted as I needed to update them. Now I cannot get the free version on my ipad. I have searched the internet to see if there is a solution, and I found a few but unfortunately none have worked. I desperately need these apps as my iPad is used for school. Is this an issue I should take up with the apple support centre or something? Please help! Thanks

How to get all the iWork apps, iPhoto, and iMovie for free on an eligible iPhone or iPad
http://www.imore.com/how-get-all-iwork-apps-iphoto-and-imovie-free-eligible-ipho ne-or-ipad
 Cheers, Tom

Changed wifi and hotspot in iOS 8. No longer supports router.

HI all.
The necessary background...
I don't have fixed Internet at home.
I utilise a wireless router that when I directly connect my iPhone 4 (7.1.2) or my iPad (prior to update to iOS 8) would initiate the usb hotspot function on either device where I then can utilise network based stuff (Apple tv, lappy, printer ect). I can go as far as to connect my iPhone to the router have the hotspot active then also simultaneously access the wifi signal from the router to the phone.. Helps get around the download limits imposed when updating stuff.
I find now that my iPad (iOS 8) can't establish a usb hotspot connection with the router. It can do the usual creatation directly plugging into the LAPPY or creating a wifi hotspot just not directly to the router.. I've done the usual turned on and off, reset network and cycled via the power home button stuff.. I've not gone down the full restore but if my hand forces it I'll try that.
Finally the question.
Did or has the Apple writers restructure the hotspot and wireless coding where it makes such things defunct? Any known work around?
cheers,
Dave

I would just like to add that I've now upgraded to a 5S and a new router. The 5S connects fine (7.1.2) aka tethers via USB where the iPad (8.0.2) still no connectivity!!
I'm sure this is on deaf ear's, still folks a spending good coin on stuff and the line in the sand keeps moving .

On transaction FBL3N report change layout and save layout icons not activ

Hi,
I am working on upgrade project from 4.6C to ECC6.0. On transaction FBL3N report change layout and save layout icons not active; only select layout icon is active.
Please advise how these two icons can be activated.
saeed

Hi,
The object F_IT_ALV has a field, the activity ACTVT, which can
contain four permitted values: 01, 02, 03 and 70.
Activity 03 corresponds to the minimum authorization, which is the
most restricted one: You can only select layouts which have
been configured already. In particular, all of the other functions
named above are inactive with activity 03.
I guess that your user-id have set activity 03 for this object.
The SAP notes 374656 and 409190 are recommended.
So, if the values 01 and 02 are not included, then
the user can't change and save layouts.
For the line item display in FI the authorization
object FI_IT_ALV has been created as an extra security check in addi-
tion to the ALV authorization object S_ALV_LAYO.
Please check note 374656 where you should be able to find
relevant info about this. Also note 637554 should be helpful.
Regards,
Aidan

FBL3N change layout and save layout icons not active

Hi,
I am working on upgrade project from 4.6C to ECC6.0. On transaction FBL3N report change layout and save layout icons not active; only select layout icon is active.
Please advise how these two icons can be activated.
saeed

You are missing an authorization object in your user profile. Run FBL3N and then run SU53 to see which auth obj is missing. Then send those details to your Security.

IW52 change notifications by deactivating one and activating other

Hi,
I would like to know the BAPI or FM to use to deactivating a user status and activating another status for a notification in IW52.
I am using BAPI_ALM_NOTIF_CHANGEUSRSTAT to set the new user status but do not know how to deactivate the existing user status.
If you know of any FM or BAPI, please let me know how to pass the values.
I have looked at BAPI_ALM_NOTIF_DATA_MODIFY and a FM STATUS_CHANGE_EXTERN but unable to change the existing one to deactivate.
If we go to table JEST, all the deactivated ones are set to X in field INACT.

Hi,
Once a status value is deactivated this is reflected by setting the INACT flag = X in JEST. The actual record is not removed.
BAPI_ALM_NOTIF_CHANGEUSRSTAT should work ok. Pass the user status and set SET_INACTIVE. Maybe your user status configuration is not allowing the status to ve deactivated ? Check the status profile with transaction OIBS.
-Paul

I have changed provider and had a new router . Laptop was chaneged wifi frequency but iPad was not. The ipad is 32gb and is

I have changed provider and had a new router . Laptop was chaneged wifi frequency but iPad was not. The ipad is 32gb and is now going very slowly like dial up. The laptop is only 4gb and is faster. The speed if Internet is about 6.5. it worked fine before we chaneged provider . Do I need to change wifi channel or does it do it automatically. How do you changed it ?

Try a new channel on your router, most router has a web interface, use your computer browser try http://192.168.0.1
also check your router manual.

So I went to update my ipod on itunes....and a box appeared saying to make sure my network settings are correct and active, but the internet is working fine. Every device in my house has great internet connection. What do I do?

So I went ot update my ipod on itunes....and a box appeared saying to make sure the internet setting are correct and active, but my internet is working fine. What do I do?

Sounds like this:
Update Server
Try:
- Powering off and then back on your router.
- iTunes for Windows: iTunes cannot contact the iPhone, iPad, or iPod software update server
- Change the DNS to either Google's or Open DNS servers
Public DNS — Google Developers
OpenDNS IP Addresses
- Try on another computer/network
- Wait if it is an Apple problem

Changing UOM and activity in routing

Similar Messages

Maybe you are looking for