Channel not initialised

Hi,
i am doing idic to file scenario...
ii can see the chequered flag in MONI....
i am doing FCC on receiving side and i ensured that all the objects are activated..
but i am getting error in CC..
description of error is:
"Exception caught by adapteraramework:channel has not been correctly initialised and cannot process messages"
plz help me out...

Hi,
Please check if you have maintained all the parameters for the FCC receiver channel correctly.
You must specify at least either fieldFixedLengths or fieldSeparator paramters. Check the below link for configuration of FCC on receiver side:
http://help.sap.com/saphelp_nw04/helpdata/en/d2/bab440c97f3716e10000000a155106/content.htm
This should help.
Regards, Gaurav.

Similar Messages

Left channel not working--it's a logic problem, but I can't debut it! HELP!!!

I'm using a SB Audigy SE card on my XP machine. In the past, I've made good music files from CDs and records (remember those?), but I have not used the thing in about 18 months, and now I'm having a weird problem.
I get output only on the LEFT channel. I'm sure it's not a problem with the input source, because I've used a cassette player and a turntable, and with both, I get output only on the left channel. This happens even when I reverse the phono cables from either device. That tells me the problem is not in the cabling leading from my device to the SB card.
I checked the speakers using the Audigy Speaker Settings application, and it shows that both speakers are working properly: when I click on CHANNEL, I get the words "left channel" and then "right channel" successively on the proper speakers. Same when I click NOISE.
This shows me that the problem is not on the (physical) output side: if it were, I would not get the words "left channel" on that channel, and then the words "right channel" on the right channel. As well, I can play videos (e.g. Youtube) and get sound on both channels.
My guess is that somehow there is some setting somewhere in Audigy that is saying "process only output to the left channel." But I cannot find any setting that might be doing that.
Anyone got any ideas???? I'm stumped.

Originally Posted by deafguy999
OOPS, I meant "right channel not working"! Sometimes I don't know my L from my R.
ALSO, CDs play properly--and my speakers are connected only to the sound card.

Error :Receiver File Channel not Initialized

Hi all,
I am using a file adapter at the receiver side with file content conversion option. When i post a message it shows an error in the message monitoring as "Reciever File Channel not initialized : Unable to proceed : null"
Please Help.....

Hi,
Check if the adapter is active or
check on this thread:
File Adapter Not Initialized Error
the error might be due to FCC. Jsut remove that and see ift he adapter works.
Regards
vijaya

Could not initialise the application's security component

When opening Firefox, I get a message "Could not initialise the application's security component. The most probable cause is problems with files in your browser's profile directory. Please check that this directory has no read/write restrictions and your hard drive is not full or close to full. It is recommended that you exit the browser and fix the problem. If you continue to use this browser session, you might see incorrect browser behaviour when accessing security features." Firefox then opens but all tabs are marked New Tab and no access can be obtained to the various websites. If I try to sign in to Google, a new window opens marked About:blank. I have wireless connection which is functioning correctly. Please help get my connection working if possible.

Thank you for this detailed explanation - I suspected the answer would be somewhere although I certainly had trouble locating it.
I haven't utilised this answer as I resurrected another laptop and copied folders from the AppData Local and Roaming folders and pasted them into my corrupted machine, which is now working well. However, I am extremely grateful to you for coming to my aid and have bookmarked the reply should it fail again.
I see someone else has the same problem, so your help will doubtless reach even further. Regards

I keep getting this diologue box as I start up Firefox "Could not initialise the application's security component. The most probable cause is problems with files in your browser's profile directory. ... what should I do exactly?

I keep getting the following dialogue box when I start Firefox " Could not initialise the application's security component. The most probable cause is problems with files in your browser's profile directory. Please check that this directory has no read/write restrictions." I am not sure how to find or change the profile directory. I have gone to the Options: General: Save files to ...box but it wont allow me to browse to another file and the box remains blank. ideas please!

See [[Could not initialize the browser security component]]
Continue here: [/questions/780717]

Why do I get an alert saying "Could not initialise the application's security component. The most probable cause is problems with files in your browser's profile directory. How can I solve it??

The full alert is " Could not initialise the application's security component. The most probable cause is problems with files in your browser's profile directory. Please check that this directory has no read/write restrictions and your hard drive is not full or close to full. It is recommended that you exit the browser and fix the problem. If you continue to use this browser session, you might see incorrect browser behaviour when accessing security features."
This is just started three/four days ago. I need assistance quickly as I can't access any secure sites e.g bank accounts/homepage etc.

See [[Could not initialize the browser security component]]

At start up, messase "could not initialise application's security component

My Grandson has a Toshiba laptop. When he attempts to start Firefox this message appears:
"Could not initialise the application's security component. The most likely cause is problems with files in your application's profile directory. Please check that this directory has no read/write restrictions & your hard disk is not full, or close to full. It is recommended that you exit the application andfix the problem. If youcontinue to use this session you might see incorrect application behaviour accessing security features."
Firefox does start, but just shows a blank page.
Can you advise what he should to eliminate the problem?
Thank you
Frank Howe

http://support.mozilla.com/en-US/kb/Could%20not%20initialize%20the%20browser%20security%20component
This will help fixing your problem!

Exception caught by adapter framework: RfcAdapter: receiver channel not in

Hi friends,
I am doing a file-RFC-file scenario. This is based on the blog: /people/arpit.seth/blog/2005/06/27/rfc-scenario-using-bpm--starter-kit The company ID is sent to the RFC through a xml file. RFC will return the company details which will be written again into a xml file.
My source file is getting picked up. But while sending the company ID to the RFC, i am getting an error. It says: <b>Exception caught by adapter framework: RfcAdapter: receiver channel not in list of running clientPools:</b>. I have checked the RFC and is running perfectly.
Can anybody help me to solve this error?
Regards,
Divija.

Hi,
it is better to restart the RFC adapter engine.
Is this RFC adapter is active in the Adapter Monitoring ?
Also change the RFC adapter configuration and activate it. Then activate the Receiver Agreement.
Also refer SAP note -730870 ( question no 17 and 20)
Regards,
Moorthy

Requested circuit/channel not available

Hello,
I have a problem with a PRI link. We have installed CCM 3.3(3) and a 3745 with a PRI link to the telco. The 3745 is configured as a MGCP gateway. When I try to initiate an outbound call, I get the following Q931 debug message:
*Mar 1 01:47:14.967: ISDN Se3/0:15 Q931: TX -> SETUP pd = 8 callref = 0x0005
Bearer Capability i = 0x8090A3
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839F
Exclusive, Channel 31
Calling Party Number i = 0x0081, 'XXXXXXX'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, 'XXXXXXXXXX'
Plan:Unknown, Type:Unknown
*Mar 1 01:47:15.127: ISDN Se3/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x8005
Cause i = 0x82AC - Requested circuit/channel not available
When I try an inbound call I get a busy signal, and a similar debug message (if I use another router to initiate that ISDN call).
This is the "show ISDN state" screen:
ISDN Serial3/0:15 interface
dsl 0, interface ISDN Switchtype = primary-net5
L2 Protocol = Q.921 L3 Protocol(s) = CCM-MANAGER
Layer 1 Status:
ACTIVE
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = MULTIPLE_FRAME_ESTABLISHED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0xFFFF7FFF
Number of L2 Discards = 1, L2 Session ID = 13
So I presume there is nothing wrong with the signalization??
I contacted the telco person, and he told be that he sees some kind of BLOCKING state on our side of the PRI link.
Please help or give at least some guidelines what to try next!
Thanks in advance...

Haha, 11 years later this post save us on CUCM 8.6.2, disabled "Inhibit restarts at PRI initialization" Works Excellent on the E1 affected.
THANKS A LOOOT.

Viewing color channels *not* in color

Hi all,
This question likely has an extremely simple solution, but I haven't found it. In versions past, Photoshop preferences had a check box to view channels in color (or not). I always liked viewing them in grayscale, mixing and matching and so forth. I've evidently been struck dumb, because for the life of me I cannot find the option in CS5 to have the blinkin' RGB or CMYK channels NOT appear in color. Help?! Thanks!!!

It's where it's always been:
Photoshop > Preferences > Interface
http://help.adobe.com/en_US/photoshop/cs/using/WS6EC2A68B-AE8D-4987-87E2-28272B744445a.htm l#WSEAC2F1E2-E15F-410e-AD65-8519BFF4BCDDa
Show color channels in color
Individual channels are displayed in grayscale. In RGB, CMYK, or Lab images, you can view the individual channels in color. (In Lab images, only the a and b channels appear in color.) If more than one channel is active, the channels always appear in color.
You can change the default to show the individual color channels in color. When a channel is visible in the image, an eye icon appears to its left in the panel.
Do one of the following:
In Mac OS, choose Photoshop > Preferences > Interface.
2. Select Show Channels in Color, and click OK.

TV Says Channel Not Available

So My TV says channel not available and I called Verzion and they are not able to help me. I pay almost $200 dollars a month for service and I get the run around. I am about to cancel my service if someone doesnt call me back or send a tech out to find out why is it that I am calling twice in one month for the same issue.

One of course is to make sure its a channel you are suppose to get.
Complaining here is just complaining to your Peers. YOu need to follow through with contacting Verizon support. http://www22.verizon.com/content/contactus/

Getting error while using CAN api's. Says channel not found in MAX.

Hi,
I am using NI-CAN series2, can card. The same is not connected to my system. Hence i have used the virtual channel 256. Here i am reading the DBC file and providing an option to the user to select a set of messages to transmitt\receive. But i am getting an error saying
"Error -1074388479 occurred at CAN Get Channel Data Type.vi
Possible reason(s):
NI-CAN: (Hex 0xBFF62201) Channel not found in MAX or the CAN database file. Solutions: Check for proper spelling using MAX; For Get/Set Property, ensure that the channel name exists in the task."
Please help.
Regards,
Yogesh

Hi Marshall,
Thanx for the reply and spending time for the same. I tried the example which u had mentioned. This example is working with 256 virtual channel. But my code is no executing and giving he same problem even after loading the DBC file into max(Same loaded im my code). Always load the dbc file in max and then only i should run the code, is it so? But this can not happen, since the user may not hav max. I hav attached the code. Pls verify it, and give me the feedback.
Waiting for the reply,
Yogesh
GET
Larsen & Toubro
India
Attachments:
CanMsgFrame.vi ‏68 KB

Planning Function giving error 'not initialise' in BPS Planning folder

Hi
Have created the std copy planning function and have included in the folder. Its giving the error the function is not initialised. What do I need to do to remove this error. Any suggestion most welcome.
Kind Regards,
Sarah

Hi Sarah,
Can you be please feed in some more information on the function you have created. What is the parameter group you have created. Is the error coming while checking the planning folder or before that.

Soap Adapter Channel not found

I'm having problems geting the Sender SOAP adapter to work.
I'm using to test it
http://<XXXXXXXX>:50000/XISOAPAdapter/HelperServlet?action=FindChannel&channel=:SunriseSoftwareSostenuto:TimeSentSoap
where <XXXXXXXX> is our domain
but this returns channel not found
SunriseSoftwareSostenuto is the Service
TimeSentSoap is the communication channel
I've already established that the Soap Adapter is active
Is there something that I've missed ?

hi
I've tried to connect to the Soap adapter using
http://xxxxxx:50000/XISOAPAdapter/MessageServlet?channel=:SunriseSoftwareSostenuto:TimeSentSoap
Where SunriseSoftwareSostenuto is the business service and
            TimeSentSoap is the communication channel
but get the error code returned below
I've tested the sender agreement/ communication channels config internally and they seem fine
could someone point me in the right direction
is it a java error
or is it a authorisation problem?
<SOAP:Envelope xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/">
   <SOAP:Body>
      <SOAP:Fault>
         <faultcode>SOAP:Server</faultcode>
         <faultstring>Server Error</faultstring>
         <detail>
            <s:SystemError xmlns:s="http://sap.com/xi/WebService/xi2.0">
               <context>XIAdapter</context>
               <code>ADAPTER.JAVA_EXCEPTION</code>
               <text>com.sap.aii.af.mp.module.ModuleException: either no channelID specified or no channel found for the specified party, service, and channel name, MessageServlet(Version $Id: //tc/xi/NW04S_21_REL/src/_adapters/_soap/java/com/sap/aii/af/mp/soap/web/MessageServlet.java#1 $)

Hi, Trying to log in with my user id and password at iocbc but was not able to access. Problem message shown : Applet not initialised or may not be supported. Please refresh the page or check the browser setting Anyone can advise? or i need to download?

Hi,
i have the same problem?
Trying to log in with my user id and password at iocbc but was not able to access.
Problem message shown : Applet not initialised or may not be supported. Please refresh the page or check the browser setting
Anyone can advise?

You need to install Java for your Mac OS version, and/or make sure it's enabled in the Java Preferences application and your browser's preferences.

Channel not initialised

Similar Messages

Maybe you are looking for