Check Status of Bit Locker Encryption on all Computers on My Network

I have encrypted all computers on my network with bit locker encryption. However, for various reasons I know that there a few that are not encrypted. Is there a tool I can use to check the encryption status of all the computers on my network?

Hi,
You can use MBAM to manage and monitor your computers bitlocer encryption status, please refer to the link below for more details:
http://technet.microsoft.com/en-us/windows/hh826072.aspx
Roger Lu
TechNet Community Support

Similar Messages

Data recovering from formatted bit locker encrypted portion.

unfortunately i formatted a partition which is bit locker encrypted having all my valuable documents and data. luckily i have bit locker recovery
key and my decryption password. i use m3 bit locker recovery software to recover my data using my store 48 digit recovery key but it give me error message 'recovery key is not matched' then i try my password, it give error message 'password not
matched' .
using cmd command 'manage-bde -status'
i get the following properties of my partition
C:\Windows\system32>manage-bde -status
BitLocker Drive Encryption: Configuration Tool version 6.1.7601
Copyright (C) Microsoft Corporation. All rights reserved.
Disk volumes that can be protected with
BitLocker Drive Encryption:
Volume D: []
[Data Volume]
Size: 218.81 GB
BitLocker Version: None
Conversion Status: Fully Decrypted
Percentage Encrypted: 0%
Encryption Method: None
Protection Status: Protection Off
Lock Status: Unlocked
Identification Field: None
Automatic Unlock: Disabled
Key Protectors: None Found
i use other data recovery soft wares it give me raw,meta and system file.
please help me in recovering my data.
sorry for unrelated description.

Hi ,
I am afraid that we cannot get the data back if the drive has been formatted even if use the
BitLocker Repair Tool.
You’d better contact your local data recovery center to try to get data back.
Tracy Cai
TechNet Community Support

Bit locker encryption requests key unless I suspend and resume the encryption

I am rolling out new computers with Windows 7 Enterprise OS on them. I am installing bit locker encryption on them. For some reason with this group of computers, and I recently rolled out a different batch of computers without this problem,
after encrypting, I must suspend and resume bit locker or upon restart of shutdown and start the user is prompted for the bit locker encryption key.

Hi,
Could you please tell some more details about the issue? What do you want to achieve here? To enable bitlocker without the prompt of the startup key? If it is , then please take a check if we have Require
additional authentication at startup policy enabled.
Besides, could you please have a share for how do you enable bitlocker?
And here is a guide for bitlocker in Windows 7, just for reference:
BitLocker Drive Encryption Step-by-Step Guide for Windows 7
BitLocker Drive Encryption in Windows 7: Frequently Asked Questions
Hope this may help
Best regards
Michael Shao
TechNet Community Support

Windows 8: Bit Locker encrypted drive "Access Denied" external drive

I rebuilt my computer and installed win 8.1 pro. Now my external drive comes up as an empty drive with "Access denied". Here is the kicker: I had turned off bitlocker on the external drive long ago as it interfered with automated backups.
Running the commands suggested here:
https://social.technet.microsoft.com/Forums/windows/en-US/738c1760-c96d-430f-9ae6-1f28f5c60998/windows-8-bit-locker-encrypted-drive-not-found-or-access-denied?forum=w8itprosecurity it shows the bitlocker but as unlocked. Drive still shows empty.
Any suggestions?
Thanks,
Markus

Ahh, turns out to be permission issue not bitlocker (or maybe bitlocker caused it to lose permissions, don't know).
Opened MyPc, right click on drive ->properties->security->advanced and selected apply to all.
Markus

Windows 8: Bit Locker encrypted drive "Not Found" or "Access Denied"

I just upgraded my Windows 7 Ultimate to Windows 8 Pro. C drive is not Bit locker protected, but D drive is. When I go to Computer and double click on D drive, it tells me one of two errors: 1) Application Not Found (more common), or 2) Access is Denied
(less common).
I thought maybe Bit locker wasn't working, but I plugged in my USB stick that is encrypted and had no issues; it asked for the password and opened the folder.
One thing I did earlier was to setup a new local account, give it administrator password, then delete the other account that I had originally used in Win7 (and in installing Win8). Maybe this caused some sort of security problem.
Please help.
Thanks.

I have been using Bitlocker since it was available with Vista Ultimate. I have had the same password to unlock my drive for 5 years. I NEVER keep my recovery key this drive. but just last month i copied all my data to another drive formatted
it to freshen it up and copied it back over. For some reason i kept the recovery key TXT file.... when i tried your method here due to the same exact problem listed the command prompt would not allow me to enter a password in CMD or powershell. Since
i had the recovery key .. THANK GOODNESS it unlocked perfectly and i was able to retrieve my 6 years of Data. So yes, this works and works well. thank You!

Bit Locker Encryption

1. Once the Bit Locker enabled on a drive, how do we confirm on data which is stored in that drive are encrypted?
2. The data size stored on encrypted drive vs non-encrypted drive will be same or different?

Hello,
I'd ask in the Windows forum on Microsoft Community.
As the Microsoft Community is on a different platform, we cannot move the question for you.
Once there, click on Participate near the top of the screen, and select 'Ask a Question' or 'Start a Discussion':
Karl
When you see answers and helpful posts, please click Vote As Helpful, Propose As Answer, and/or Mark As Answer.
My Blog: Unlock PowerShell
My Book:
Windows PowerShell 2.0 Bible
My E-mail: -join ('6F6C646B61726C406F75746C6F6F6B2E636F6D'-split'(?<=\G.{2})'|%{if($_){[char][int]"0x$_"}})

Status of Itunes library after deauthorizing all computers

When I deauthorize all my computers, does my itunes library remain intact, even music received from cd's and 3rd party. Will I be able to authorize my computer to play the same library as before.
Please advise

Yes. Deauthorizing all computers simply clears the link between all computers and a particular iTunes sign-on ID. Once you re-authorize any computer you want associated with that iTunes ID again, then that ID will be able to download and play songs purchased by that ID in the iTunes library on the computer that has been authorized to it.
The only thing you need to remember is that a "Deauthorize All" function can only be done for a particular Apple/iTunes ID once a year.
Cheers,
GB

Can't view all computers on a network

I'm at a university and when I log onto my area network I get a list of some 1750 computers (up to IF-H, I lose everyting after IF-I to Z). Is there a way to view all, or view a subset? I can't access my department server without viewing J and above.
K

Here are some ideas and questions.
1. Make sure that the DSL or cable modem is connected to the Snow's WAN port, not its LAN port.
2. Are all 5 computers connecting to the network wirelessly, or are some connected via Ethernet? If via Ethernet, what is your network structure?
3. Can all the computers not only "see" your network, but join it? (Does a check mark appear next to the correct network name in each computer's AirPort status menu?)
4. Can both computers that can connect to the Internet do so simultaneously?
5. Check the IP address of each computer when all are joined to your network. Do they all have the form "10.0.1.x"? This is expected if each is obtaining an IP address via DHCP from the base station.
6. Are the balky computers MacBooks and/or MacBook Pros? Note that this month Apple came out with an AirPort Client Update for MacBook and MacBook Pro, which is intended to address an AirPort performance issue while running on battery power under Mac OS X 10.5.8.

Data Recovery from Partitioned and formatted Bit Locker Encrypted Drive

Recently because of some issues in windows 7 installation from windows 8 installed OS. it was giving as the disc is dynamic windows can not be installed on it. so at last after struggling hard no other solution i partitioned and formatted my whole
drive so all data gone included the drive which was encrypted by bit lockers.
For recovery i used many software such as ontrack easy recover, get data back, recovery my files professional edition but still i couldnt able to recover my data from that drive. then i found some suggestion Using CMD to decrypt my data first
http://technet.microsoft.com/en-us/library/ee523219(WS.10).aspx
where it shows it successfully decrypt my data at that moment my drives were in RAW format excluding on which windows is installed and then in CMD i check Chdsk which also shows no problem found. but now problem is still i coudnt able to recover
my data then i format the drive D and again tried to recover data using above software after decryption still no result.
Now i need assistance how i can recover my encrypted drive as it was partitioned and also formatted but decrypted also as i have its recovery key too. thanks

Hi ,
I am afraid that we cannot get the data back if the drive has been formatted even if use the
BitLocker Repair Tool.
You’d better contact your local data recovery center to try to get data back.
Tracy Cai
TechNet Community Support

External drive bit locker encryption hang up , while entering password

recent i encrypted my 1tb external hard drive, and ts worked fine , suddenly yesterday i entered a password in password window its hangs up , i waited for 3hrs its still like same (not responding) i need that data its really important to me

Try try Bitlocker repair tool..http://www.microsoft.com/en-us/download/details.aspx?id=17294
"The BitLocker Repair Tool can assist administrators in recovering data from a corrupted or damaged disk volume that was encrypted with BitLocker."
Using the BitLocker Repair Tool to Recover a Drive
http://technet.microsoft.com/en-us/library/ee523219(WS.10).aspx
http://support.microsoft.com/kb/928201
Hetti Arachchige V Aravinda | Network & System Administrator (B.Sc, Microsoft Small Business Specialist, MCP, MCTS, MCSA, MCSE,MCITP, CCNA, CEH, MBCS)

How to Open Ports for HP Printers for all computers within the network (router)

Hi,
I have the EA6700 router and a few HP printers and Multi purpose printers/scanner/fax ...
When installing the print drivers, they are ok. Sending to printers are not a problem. However, the problem comes with scanning.
The HP Software ask to open a port for it... How do I do that? I checked, it seems other computers are affected by it too after changing to this new router.
I read that it can be done on the "App and gaming" section at the Security page. Do I go to the port forwarding section? But it only forward to one computer. that doesn't work...
I'd like to open a port and a lot of other IPs can print and scan from it.
Thanks

Ports are not needed to be opened on the LAN side of the router for Printers and Scanners. I recommed that tiy contact hp for help and information regarding setup and configuration of those devices. Also the addition of a external Gb network switch for these devices is recommended as well. Would help eliminate any un-necessary router configuration or processing.

How i can export and distribute setting; network.automatic-ntlm-auth.trusted-uris" to all computers in the network (With Folder Rederiction enabled)?

Hi,
We are about to enable SSO in our environment. As a result, I need to modify the value for user_pref("network.automatic-ntlm-auth.trusted-uris", "my domain");>>prefs.js.
I created a simple .bat file to make the necessary mod and add the line to pref.js. When I run the file it outputs the prefs.js to the same location, not the Mozilla AppData folder. We are a Win7 environment with folder redirection enabled. Therefore, our user's Mozilla AppData folder is located at \\my domain\dfs\XenDesktop\Profiles\username\AppData\Mozilla\Firefox\Profiles\default (random default profile name). My question is what is the best course of action to add this pref. to all PC user's pref.js file? keep in mind the pref.js is located on the hidden network path I included above. I apologize if my question is not easy to understand.

cor-el, thanks for you reply.
Yesterday, prior to my post, I did try the mozilla.cfg method. I read your reply to another FF user's, similar question. Here are my complete steps.
1. created a txt file with the following info: defaultPref("network.automatic-ntlm-auth.trusted-uris", "ngs.org"); // set new default value
2. saved the file as mozilla.cfg
3. dropped the file in C:\Program Files (x86)\Mozilla Firefox
4. Created local-settings.js with the following info:
pref("general.config.filename", "mozilla.cfg");
pref("general.config.obscure_value", 0); // use this to disable the byte-shift
5. dropped the file in C:\Program Files (x86)\Mozilla Firefox\defaults\pref
When I launch Firefox the network.automatic-ntlm-auth.trusted-uris should say ngs.org, but the value is still blank.
Any help is greatly appreciated.

Kindly advise how i can export and distribute settings done on "about:config == network.automatic-ntlm-auth.trusted-uris" to all computers in the network. What is the best way to effect this changes on all Machines?

I want user to access sharepoint on Mozilla without being prompted for credentials instead it should use logged on credentials

Hi Meshackl, there is a very simple way with the distribution.ini file. Mike Kaply describes how to do that here:
http://mike.kaply.com/2012/03/26/customizing-firefox-distribution-ini/

Check Status BBPSC04 showing all the shopping carts

We are on SRM 5.0
When a user clicks on Check Status. It is showing them all the shopping carts even those which are not created or approved by them.

Hi Srini,
In 'Check Status' all the shopping carts are shown if you do not give anything in the search criteria except the ones that are completed irrespective of the purchasing org / P.group.
If you want to see the shopping carts created for that P.Group / P.org mention the same in the search criteria of the 'Find' tab.
If you want to see the shopping carts only created by you then go to 'Centralized Purchasing' Link and click on the ' Check Status'. There you can see only the shopping carts created by you.
In case of any clarification feel free to ask.
Award points for suitable answers.
Rgds,
Teja

Bit locker unable to turn on

Hi,
I am trying to turn on Bit locker for removal Disk, could not succeed. System says that, required services not enabled. I remember I changed the registry setting to disable to bit locker encryption. I do not re collect what I have changed. Could you
please let me know what setting value is to be set for enabling the Bit locker encryption.
Thanks
Sreekanth.

Hi,
As narcoticoo mentioned, do we have TPM chip on the computer? Please take a look into Device Management, if the TPM driver is installed then it will show up in the Device Manager, under Security Devices as mentioned.
Please also take a look at the below article regarding how to turn on/off bitlocker without TPM:
How to trun on or off bitlocker without a TPM for Windows 7 Drive
Please note: Since the web site is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy
of this information.
For more information regarding Bitlocker for Windows 7, please take a look at the article below:
BitLocker Drive Encryption Step-by-Step Guide for Windows 7
Hope this may help
Best regards
Michael Shao
TechNet Community Support

Check Status of Bit Locker Encryption on all Computers on My Network

Similar Messages

Maybe you are looking for