Checking FDD

Hello,
I installed the Enterprise Manager with no problem.
Since that, whenever I start the console service, it starts checking my floppy disk drive. It makes an annoying noise and doesn't really speed up the system I guess.
I tried to find some relevant details in the documentation but havent found any so far.
Could someone help me turn off this "feature"?
Thanks!
Monika

To solve this issue (hopefully) see
OracleDBConsole

Similar Messages

Computer won't start after shutdown

Hello,
I was using my computer with the 875P NEO-FIS2R motherboard. I have been using it for like 1-2 months. I ran live bios update and updated my computer. After a couple of weeks I decided to shut down my computer and when i tried to turn it on.. it doesn't turn on, but the fan spins but it stops and spin and stop and keeps on going on like that. I shutted down the computer again and clear my CMOS. I turn it back on it turns back on. Then it load to windows correctly. Then I decided to shut down the computer again. It gave me that error. Also I tried clearing cmos but nothing happen the light and fan keep blinking and spinning. Do you know what the error is? Can anyone help?

the bios disk rescue go only work if the board is working
and send some basic command to check fdd for the bios on it
here nothings append won't boot at all that's the problem of this board
only when removing 4pin 12v then push power on then have nb fan/led on; cpu fan on; led of lan; and 4green led directly on d-led bracket
but no other activity on the board
and also check for componant no burn
also psu,cpu,memory or else working fine (yes have got new one 875p)
i don't want that append to my new board
i just worried now that some other people have the same problem
and maybe other also and we don't know yet
is it the hardware or the software (bios 1.8 on my board) ??
that's what we or msi must find

K7T266 PRO2 (MS6380 Ver 3.0) FDD Controler Problems

I just purchased a new boxed OEM MSI K7T266 PRO2 (MS6380 - Ver 3.0) motherboard from JUST DEALS on E-bay which seems to have very sparce (or none) documentation for download on this site. This is a non-raid board which has the AGP Pro video card socket (with the white lock and release lever at the end of the AGP female connector). The board can also be identified with the following rather unique component/connector layout at the bottom end of the board:
1. In place of where RAID connectors attach to most of these model boards, this board has three aux USB connectors above the connector where the case front panel connectors usually plug in.
2. There are 3 CDROM audio connectors at the lower left below the last PCI slot.
3. To the left of the case front panel connector, there are two rows of connectors and jumpers which appear to be for use with a case which has front panel audio connectors. I believe the jumpers are for the purpose of selecting which audio output to use (front or the standard rear sound output jacks.
4. The area between the last PCI slot and the USB and front panel audio connectors described above, the motherboard is rather blank with no components or even places where optional components have not been installed.
5. This motherboard has a Phoenix bios whereas most other K7T motherboards made by MSI seem to be AMI bios.
6. Finally, when doing a search for MS6380 Ver3.0 on Google, all the hits seem to be in Russian, German or French. I suspect that this MB may have been manufactured for the European market. BIOS display is in English, however.
PROBLEM
I have installed an AMD Athlon TBird 1.2 ghz cpu with 40mb WD hard drive which already had Windows Me and lots of other SW installed. The system boots just fine from the hard drive and all works well except for the Floppy drive. When I try to access the FDD with a know good disk installed with valid data, it comes on and spins up, the front light blinks and after about 30 seconds of continuous running, a message comes up "floppy disk not formated, format now: (Y/N)" If I try to format the disk, it will not format and the system will ask to check to see if a disk is installed. Changing floppy disks does not help, whether this is a disk which has verified data installed or just a formated blank disk. I have tried two different FDD cables and 3 different Floppy drives and always get the same result. I have checked for bent or broken pins in the connectors and found they are all good. The FDD is a 1.44 MB and is connected to the end of the two-drive cable. No other FDD is installed. When I go into the BIOS setup, I verify that Drive A is installed as a 1.44BM 3.5" Floppy and None is selected for Drive B.
I am currently at a loss to know how to proceed here. I am wondering if this could be a BIOS problem but I am not sure if I can find BIOS update on the MSI Web site when they do not even list a MS6380 Ver 3.0 motherboard at all.
I am considering installing a PCI FDD controller card but not sure that these are even manufactured.
Please help.

To Toenne:
Thanks for the reply. This has to be a BIOS problem since the FDD has to be accessed by the BIOS before any software or installed chipset drivers on the HD are ever used. With my problem, I cannot even boot the system from the FDD.
I tried resetting CMOS and that did not help. I wonder if there is some kind of multi-mode floppy disk drive which this BIOS expects to see other that you standard old fashion IBM 3.5" 1.44gb drive. The solution is likely to reflash the BIOS except with this odd MB serial number, I am not sure if I can find the latest BIOS software for this Phoenix chip.
Does anyone know if there are any PCI FDD controller cards on the market where I could disable the on-board controller and use a plug-in card?
Thanks

I get no wireless signal in my home, so need a network extender for the Lumia 2520. Specs indicate LTE FDD network:Band 20 (800MHz), Band 3 (1800 MHz), Band 7 (2600 MHz). Does Verizon offer a network extender that will work with the Lumia?

I get no wireless signal inside my home, only outside, so I need a network extender that will work for the Lumia 2520, Specs indicate it uses LTE FDD netork Band 20 (800MHz), Band 3 (1800MHz), Band 7 (2600 MHz). Does Verizon offer a network extender that will work with the Lumia 2520?

We want to make sure you get service in your home Astromandata! I can check your area to see if you qualify for the network extender. What's your zip code? If it does qualify than you will be able to use it for your Lumia to support your voice services. Find out more information here: http://spr.ly/6585fNlt Is anyone else having this issue?
AmberF_VZW
Follow us on Twitter @VZWSupport
If my response answered your question please click the �Correct Answer� button under my response. This ensures others can benefit from our conversation. Thanks in advance for your help with this!!

FDD unknown protector state

I'm hoping someone has seen this before and can help me out here. For some reason our laptops we're encrypting with Bitlocker all show up as non-compliant if they have an FDD. They drive is encrypted, but MBAM sees the protector as unknown, even
though they're password protected.   I'm not sure if it's a bug in bitlocker or if I missed something. The GPO is set to require a password, but allow auto-unlock.
Volume F: [Label Unknown]
[Data Volume]
    Size:                 Unknown GB
    BitLocker Version:    Windows 7
    Conversion Status:    Unknown
    Percentage Encrypted: Unknown%
    Encryption Method:    AES 256 with Diffuser
    Protection Status:    Unknown
    Lock Status:          Locked
    Identification Field: Unknown
    Automatic Unlock:     Disabled
    Key Protectors:
        Numerical Password
        Password
The Protector state shows up as "unknown", and the compliance status details shows that "An unknown error has occurred.

Hi J.Runyon,
Would you please share more details of the issue ?
When did the issue start to occur ?Did the MBAM work correctly before ?Have you checked the status from the client ?
Will only this specific machine come across this issue or all the machines?
Have you made any modifications to the machine ?
If this is the first time to use the MBAM,we can refer to the following link to configure the MBAM
Planning for MBAM 2.5 Group Policy Requirements
https://technet.microsoft.com/en-us/library/dn645338.aspx
Best regards
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

FDD Doesn't Work

Hi
I have a KT3 Ultra2-R Mobo on which everything is working OK except the FDD. I have checked the BIOS settings (AMI Ver. 3.31a) and all seem to be correct to me - the board usually picks up anything automatically like another HDD for example.
I have tried another FDD and Ribon cable but this didn't solve the problem. I am being to think that it maybe a problem with power as no lights come on the FDD on boot up.
Anybody got any thoughts ??
Thank you in advance
PLOPPY

If the light of the floppy drive continuously burns after start up, most likely the flatcable is inserted upside down. Check the pin 1 position of both Motherboard and drive and make sure the coloured lead of the flatcable is connecting the no.1 pins. I've had cables with notches on them that could fit only one way on the board and into the drive and it was wrong! I had to file off the notch to make the connector go in the right way.
In modern slick looking cases there is a special slot for the floppy which requires the front part (with the flap) to be taken off. No problem. If the drive won't work and reports even a failure it may be that the drive is too closely mounted to the front end and that the eject button is slightly pushed inwards. You only need a fraction of push on the eject button for it not to work. Ease back the drive a millimeter and that should do the trick.

Satellite Pro L10: PXE-E61 - Media test failure check cable error message

I recently bought an L10 laptop without the hard drive and everytime i try to boot it with a newly installed hard drive i get this message .
PXE-E61 :MEDIA TEST FAILURE CHECK CABLE
PXE-MOF: EXITING PXE ROM
OPERATING SYSTEM NOT FOUND.
CAN SOMEONE MAKE SENSE OUT OF THIS AND EXPLAIN IT TO ME AND ALSO HOW CAN I GET RECOVERY SOFTWARE AS I DO NOT HAVE THE TOSHIBA RECOVERY CD BUT I DO HAVE THE CoA STICKER ON LAPTOP.
IM DESPERATE PLESE HELP

Hi Nash,
Your problem is quite straightforward and can be summarised as follows.
1. You bought a notebook without a hard drive and presumably installed a new hard drive.
2. You then tried to boot the system from the new hard drive.
The problem here is that there is not yet an operating system installed on the hard drive and as a result the BIOS will try to find an operating system in other places, such as your CD drive, your floppy drive (if you have one), and finally a network connection to a local LAN. If none of these are successful you will receive the error message that you reported.
The obvious solution here would be to install an operating system on your hard drive and you can choose either an original Toshiba recovery disc (obtainable from your local Authorised Service Partner) or you can opt to buy an original Microsoft XP disc in which case you will need to download and install the Toshiba utilities and drivers from the Toshiba web site. My preference would be to get a recovery CD from Toshiba since this will install a guaranteed system with all the necessary utilities and drivers.
Your BIOS will normally be set to search for an operating system on your FDD/CD-ROM, then your HDD and finally on a network lan connection. Once you obtain a recovery CD just load it into your CD-ROM and power on your notebook. The system should find it and then start the installation process. Just follow the on-screen instructions and you should have a valid operating system on your hard drive in about 20-30 minutes.
best of luck,

Internal USB connections for Mitsumi FDD

Hi everyone.
I'm 57, retired, trying to impress my children, grandchildren, and even maybe myself with this new hobby project of mine.
This is my first question post. I may have a few (??) others as this project goes on.
My old, current, PC is a DELL Dimension XPS R450 running Win98 I upgraded with a P3 1Ghz with 640MB RAM, 1 WD120GB & 1WD 40GB HD's, Yamaha CDRW and a new ASUS CD ROM with Comcast High Speed internet. I use mostly Netscape 7.02. PC runs great!
I am building my first PC with the components listed below. It has not been plugged in yet and no OS or drivers of anything loaded. I have several printouts from "building your PC" sites to follow.
I still have to decide where I want what connected to. I have, as of now, 1 WD 160GB SATA and 1 Seagate 160GB ATA HD's. I'd like to connected them to SATA 3 (Win XP loaded here) and IDE 3 in a Raid 1 format for mirroring thus freeing up IDE 1 & 2 for individual channels for the CDRW and future DVD RW drive. That's why I got the ATA133 Controller card for extra hookups (DVD Rom drive). My monitor arrives later this week.
I have 2 front USB ports on the case with 2 internal wires with 2 female clips going to JUSB1 pins. One clip goes to the #1-8 pins & the other to the #2-10 pins.
There are no JUSB2 pins on this board. It would have made this too simple.
I do not have the D-Bracket connected because that goes to all the JUSB1 pins and the JDB1 connection pins.
My question:
I have a Mitsumi FA 402 in Black 7-1 internal FDD (reads all the camera card types also) that has an internal USB wire and 4 pin (Female) clip that I don't know where to connect. I thought of connecting it to the 4 pins of the JDB1 but then figured that was not the same because the D-Bracket had its own USB connection that went to the JUSB1 connection and the JDB1 was strictly for that other wire on the D-Bracket. The rear of the Mitsumi has the standard Floppy cable pins, the 4 pin white power clip and the black wire for the USB clip. It states on the website "# USB Powered: No extra power supply required". I thought that if a device connects to a USB connection that the connection also supplies the power for that device. Why would I have to connect the white four pin power connection to the main PS, or am I wrong (confused)?
I have no manual and the website does not display a download manual for this model.
If I disconnect the one front 4 pin USB wire from the JUSB1 connection and connect the 4 pin clip from the Mitsumi in it's place will that work and will I still have one working front USB port? I think it would work.
Can I ever connect the D-Bracket? I have read in the past pages of someone wanting to connect a "Y" splitter for his fans to the pins on the MB and I learned that is a "no no". I am assuming this also goes for trying to put a splitter on the USB pins (if they even make this type of splitter)?
I have already read back pages and "Guides" posted by others of this forum for a similar problem with negative results.
I can say that the 3 days I have read this forum, it is the "BEST".
I'm sure someone has solved this problem with having front USB ports and an internal device needing USB connection. Any help or suggestions?

All,
I think I found a card that may be of use for future info to others if this problem arises again. This is the first site I checked using a Google search for USB2.0 CONTROLLER CARD PCI EXT / INT
http://www.outpost.com/product/3744226
8 Port Firewire 1394 / USB2.0 PCI Card ( USB 2.0 - 4 Ext + 1 Int) ( 1394 - 2 Ext + 1 Int)
It also has pins connections on the internal of the card.
# Supports Windows 98SE, ME, 2000, and XP
# 4 External Type A USB 2.0 Ports
# 1 Internal Type A USB 2.0 Port
# 2 External 1394 Ports
# 1 Internal 1394 Port
# 1 additional port (pins) coming out from J3 For USB 2.0
# 1 additional port (pins) coming out from JP3 For FIREWIRE
# J3 & JP3 is for those people have USB and Firewire port in the front of their computer case.
* Pin header of Single port for cabling to front panel (Cable not included)
USB2.0 CONTROLLER CARD PCI EXT / INT
Guess I'll check the rest of the links from Google but this seems to fill the bill.
Thanks to all.

I am using Windows 8.1 i have an External Hard Disk and one drive is now inaccessible due to sudden power failure few days ago. Now it shows "Data error (Cyclic redundancy check)". I want all my important files and Pics. How ?

Hi,
I am using Windows 8.1
I have an External Hard Disk i have partitioned it to 4 parts.
One drive is now inaccessible due to sudden power failure while listening Music from that drive few days ago.
Now it shows "Data error (Cyclic redundancy check)".
I tried all the procedures provided here like
chkdsk /f, diskpart, rescan etc
but no result :( (i mean all processes failed. They could not detect the drive).
Please help me to get those data, pictures and project files.
thank you

Then why aren't you posting this in the Windows 8 forums found @
http://social.technet.microsoft.com/Forums/windows/en-US/home?category=w8itpro
This is a Windows 7 forum for discussion about Windows 7.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. ”

IF-statement in Personas that is checking if control is inactive?

Hi,
I have this simple script in screen personas that is clicking the option: "Attachment list". Everything is working great if there is attachments.
If there are no attachments the option is "inactive" or "greyed out". This will result in a script error.
I thought this was going to be an easy fix by adding IF statement to the the script. But howerver I specify the critera for the IF statement the script will always try to click the Attachment list. The condition will simply always be TRUE.
Am I missing something here or is it not possible at this time to script an IF statement that is checking if the control is inactive or similar?
Best Regards,
Oskar Söderlund

There is another way, but it will get a little tricky.
Outside of the transaction IE03 you can check for the existence of attachments for a piece of equipment by looking in table SRGBTBREL. Field TYPEID_A will be "EQUI" and field INSTID_A will be the equipment number, zero-padded on the left to 18 characters long. Use SE16 to look in the table and you'll get the idea.
You could wrap this test in an RFC-enabled ABAP function and call that from your Personas script button. Use the return value from that RFC to decide if attachments exist or not and how the script should respond. Details for how to write such an RFC and call it from a Personas script are in this blog: Calling RFCs from a Personas script.
Like I said, this isn't straightforward and perhaps Personas scripting should include an active/inactive test in addition to the exists/doesn't exist test. Until then, however, there is a way if you don't mind a bit of ABAP programming.

Checking null and not null values

Hi!
We have a job schedule table that has a column for each day.
JOB_ID, TIME_ID, MO, TU, WE, TH, FR, SA, SU
1 1 X
1 2 XSince the same job can be on different days and times, we need to check all the instances of
that job.
Sorry for the formatting - the X is an indicator; i.e. Wednesday and Saturday.
How can we solve this?
Thanks!

Your requirements are not really clear.
Perhaps this query could help:
-- Your Data:
with yourtable as
select 1 job_id, 1 time_id, null mo, null tu, 'X' we, null th, null fr, null sa, null su from dual union all
select 1 job_id, 2 time_id, null mo, null tu, null we, null th, null fr, null sa, 'X' su from dual
-- Query:
select job_id, time_id, 'mo' day from yourtable where to_char(mo)='X' union all
select job_id, time_id, 'tu' day from yourtable where to_char(tu)='X' union all
select job_id, time_id, 'we' day from yourtable where to_char(we)='X' union all
select job_id, time_id, 'th' day from yourtable where to_char(th)='X' union all
select job_id, time_id, 'fr' day from yourtable where to_char(fr)='X' union all
select job_id, time_id, 'sa' day from yourtable where to_char(sa)='X' union all
select job_id, time_id, 'su' day from yourtable where to_char(su)='X'Edited by: hm on 29.07.2011 01:40
Edited by: hm on 29.07.2011 01:41

Check for null and empty - Arraylist

Hello all,
Can anyone tell me the best procedure to check for null and empty for an arraylist in a jsp using JSTL. I'm trying something like this;
<c:if test="${!empty sampleList}">
</c:if>
Help is greatly appreciated.
Thanks,
Greeshma...

A null check might not be you best option. If your requirement is you must have both the date and time component supplied in order to populate EventDate, then I would use a Script Functoid that takes data and time as parameters.
In the C# method, first check if either is an empty string, if so return an empty string.
If not, TryParse the data, if successful, return a valid data string for EventDate. If not, error or return empty string, whichever satsifies the requirement.

Contact form check boxes will not work on a Tablet

Hi there,
I created a website (Desktop) and a mobile version (Phone). I did not create one for a tablet but have relied on the Desktop version if someone views it on a Tablet.
Here's the thing, I created a contact form with checkboxes. It works great on a desktop (because people check the boxes with their mouse), however, it doesn't work on a Tablet, when you try and check the boxes with your finger.
Help!

Please share the site URL.

My ipad wont let me download certain apps because it needs ios 7 but when i check update it says there is none?

my ipad has IOS 5.1.1 version and i know there is newer update for them as when i go to download certain apps it wont let me because it needs IOS 7 but when i have plugged it into itunes it says no update needed?

Hello courtneys100,
Thanks for using Apple Support Communities.
From your post it appears that you are using an earlier iPad, which can only update to iOS 5. Some developers do offer compatible versions of their apps for people running older iOS versions, but ultimately it is up to that developer to make an older version. Check out the article for more information about installing the latest compatible version of an app on your iPad.
Install the latest compatible version of an app on an earlier version of iOS or OS X
Cheers,
Alex H.

Checkbox item: How to get all values checked?

See http://htmldb.oracle.com/pls/otn/f?p=24317:46
The report query is simply
select
'One' one,
'Two' two,
'Three' three,
'Four' four
from dualThe checkbox item is a named static LOV with STATIC2:ONE,TWO,THREE,FOUR and a Source value of ONE:TWO:THREE:FOUR so that all boxes appear checked when the page is first rendered.
All the 4 columns have a column condition like
instr(':'||:P46_COLS||':',':ONE:') > 0to ensure that column is rendered only if the corresponding checkbox is checked.
The report has Dynamic column headings with the following PL/SQL function body
return 'ONE:TWO:THREE:FOUR';To my (pleasant) surprise, this works very nicely. When column TWO is conditionally not rendered, its corresponding column heading is also skipped with no effort on my part. Nice.
Question:
Instead of "hard-coding" that string ONE:TWO:THREE:FOUR in the 2 places I mentioned above (checkbox item source and report heading), is there a way to access the "all values checked" version of that LOV item so that it will dynamically pick up the latest LOV changes? The way I have done it currently, if I change the named LOV, I need to also change those 2 places where I have hardcoded the values.
Any ideas? Thanks

Scott:
I thought about that but the LOV has dozens of values, each with a verbose display value and a return value of the column name (upto 30 characters) and the display values are still being "worked on" by the users.
So, the "all columns" string would be a big, unweildy string that would be hard to edit.
It is much easier to edit, resequence and generally work with a Shared Component LOV defined as a Static LOV because you get that nice page (4000:4111) where you can read everything nicely formatted instead of a STATIC2:<big long string>!
Can I have my cake and eat it too?!
Thanks

Checking FDD

Similar Messages

Maybe you are looking for