Choppy video streaming after upgrading E4200 firmware to ver. 1.0.03

Video streaming was fine until I upgraded the firmware. Is it possible to downgrade the firmware?

You mentioned in your post that you upgraded the latest firmware. So after upgrading the firmware did you reset the router? It is recommended to reset the router after firmware upgrade. Steps to reset the router:
Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on. After this process reconfigure the router. Power light should blink when you perform the reset process.
After the process reconfigure the router as per the ISP setup.. Then try to do the following steps:
A] With the help of Cisco Connect Software (if at all you have installed the router with the help of this software)
          1] Open the software and go to the option which says "Router Settings"
          2] Then click on the option which says "Advanced Settings" which will take you to the router's configuration page.
         3] Lower the MTU (Maximum Transmission Unit) from 1500 to 1400 or less (usually found on your router's main/ basic setup page)
         4] Then go to the Wireless tab, keep network mode as mixed,
For Channel Settings of 2.4 GHz you can make Channel Width to 20 MHz only and Channel to 6, 9, 11..
For Channel Settings of 5 GHz you can make Channel Width to 20 MHz only and Channel to 40 or 161...
B] If you haven't installed Cisco Connect then you can log on to the router's user interface using it's default IP address in the browser which is 192.168.1.1 and type in 'admin' as the password leaving the username field blank. This will take you to the router's web interface and then follow steps as mentioned above to make the changes.

Similar Messages

Choppy video streaming...

I'm trying to watch a live video stream on MLB.com (major league baseball).
It's playing back one frame at a time. If it was just choppy, it wouldn't be as bad.
Anyway, it used to work fine.
Real Player, and Windows Media Player are both doing the same thing.
It's also doing it when I watch it from within the browser.
That's what makes me think that it's a computer problem rather than the connection.
Can someone help?
I use DSL, via my airport wireless.
All other internet related things work fine.
thanks.

You mentioned in your post that you upgraded the latest firmware. So after upgrading the firmware did you reset the router? It is recommended to reset the router after firmware upgrade. Steps to reset the router:
Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on. After this process reconfigure the router. Power light should blink when you perform the reset process.
After the process reconfigure the router as per the ISP setup.. Then try to do the following steps:
A] With the help of Cisco Connect Software (if at all you have installed the router with the help of this software)
          1] Open the software and go to the option which says "Router Settings"
          2] Then click on the option which says "Advanced Settings" which will take you to the router's configuration page.
         3] Lower the MTU (Maximum Transmission Unit) from 1500 to 1400 or less (usually found on your router's main/ basic setup page)
         4] Then go to the Wireless tab, keep network mode as mixed,
For Channel Settings of 2.4 GHz you can make Channel Width to 20 MHz only and Channel to 6, 9, 11..
For Channel Settings of 5 GHz you can make Channel Width to 20 MHz only and Channel to 40 or 161...
B] If you haven't installed Cisco Connect then you can log on to the router's user interface using it's default IP address in the browser which is 192.168.1.1 and type in 'admin' as the password leaving the username field blank. This will take you to the router's web interface and then follow steps as mentioned above to make the changes.

USB Share broken after upgrade to Firmware 1.05.36

Hi, Problem after upgrade to Firmware 1.05.36. When connecting USB disk there no share created for the newly connected disk. The result is: Broken functionality backup to USB diskBroken functionality restore from USB disk It worked OK before thefirmware upgrade (I have been using this a lot). I have checked through ssh login: the disk mounts ok. Please fix!!

Yes, that's exactly what I mean - the shares that are automatically created when you insert the drive (ie the functionality you seem to have lost). There's no setting to enable/disable that, at least that I know of. It should just always automatically do it. The shares themselves are just links in the /shares folder, to the relevant mount folder if what I can see on my MCM via SSH is what I think it is. You may be able to manually make the links yourself via the command prompt as a work-around. Please note that I haven't tried this myself, as my one works. But what I would do is try and install the firmware image again over the top of your current one. You can download it manually from this page and then install it via the dashboard using Settings > Firmware Update > Manual Update. There should be a button there that you press and point it to the firmware image file you downloaded and stored on your local machine. If the button isn't there, try a different browser (I find on my Windows machine it doesn't appear under Chrome, I have to use IE for that job).

Problem after upgrading New Firmware 14.1.G.1.534. Asking for Password when i click settings menu

Problem after upgrading New Firmware 14.1.G.1.534. Asking for Password when i click settings menu, for which i never kept any password.
Any DEFAULT Password so that i can unlock the settings menu.

That's quite odd, just repeat the update process
Update Service (SUS)
http://www.sonymobile.com/gb/tools/update-service/
http://www-support-downloads.sonymobile.com/Software%20Downloads/Update_Service_Setup-2.11.12.5.exe
PC Companion (PCC)
Bridge (for Mac)
Alternatives on How to backup Xperias
http://talk.sonymobile.com/thread/36355
"I'd rather be hated for who I am, than loved for who I am not." Kurt Cobain (1967-1994)

Dashboard widget with streaming video breaks after upgrade to Mountain Lion

Hi. I recently upgraded from Snow Leopard to Mountain Lion. Under SL, I had an OS X widget that was a web clipping of a streaming mpeg image being produced by a Linksys/Cisco WVC54GCA web camera. When I brought up the dashboard, the OS would start streaming the data from the mpeg filename, which looks like "hostname.com/img/video.mjpeg".
After upgrading to Mountain Lion, I noted that the widget never fully loads, indefinitely displaying a "Loading Clip..." mesasge. After deleting and re-adding, I can still get as far as adding the web clipping to the dashboard at the right dimensions, but there's no content.
Unfortunately the camera unit doesn't provide for the display of HTTP access logs, so I can't see if there's an issue there, but my understanding is that if I can display the image in a Safari browser, it should work just fine in Dashboard too. (I did make sure that, where needed, the username/password for accessing the video are included in the URL.)
I did sniff the network traffic between my system and the camera host, and show that video traffic starts flowing between the two as soon as the widget is brought up. So, it's almost like the widget doesn't know when to stop "loading" and start "displaying," perhaps because the HTTP request is never truly "done."
Can anyone speculate if something may have changed in Mountain Lion affecting the ability of web clipping widgets to display streaming video?
Thanks,
Chris

Hi James
I have exactly the same problem with the same "Loading clip" then blank. I have been trying a lot of stuff to get this working, but haven't had the chance of sniffing the network traffic as you have done. By reading what you said about the traffic seems to be flowing without the picure being displayed makes me even more puzzled by this. I never had a streaming video while I were using Snow Leopard, but I had a still-image, as I also do now in Mountain Lion. I recently began to research for a way to display the video.cgi MIME image that my camera produces, and I've also concluded that this should be an easy task for the dashboard web clip function; the video does display in safari after all.
I suspect that our cameras uses the same built in webserver solution written by a "Steven Wu". Cheap webcameras frequently uses his script with MJPEG (stream of JPEG pictures) to avoid the expensive licenses of using other video codecs.
I read this a bit down at this site: http://channel9.msdn.com/coding4fun/articles/Everyone-Loves-Babies-Webcams-and-M otion-Detection
Have you come any closer in your research?
I have started to think that maybe I have to write a dashboard widget on my own to accomplish this.
trelements

EA6500 Choppy Video Stream to Xbox360

I've been viewing some videos streamed through the EA6500 from a Qnap 419p II NAS, and several video files are playing back extremely choppy.
I can confirm that the video files play fine on the Xbox360 using a USB key and have also previously streamed these videos without any problems using a Belkin Wireless Pre-N router (that I upgraded from) streamed from the same NAS.
I've attempted to configure the Media Prioritization feature, but haven't noticed any different results. I have also adjusted other various settings that haven't affected the playback in any way.
My only guess is that some of the files are encoded in a format that the router is struggling with - the video files are not HD videos, and their bitrates are generally quite low - if my old Belkin router can do it, the EA6500 shouldn't have any problems either.
Any help would be greatly appreciated!
Here's my router's configuration:
- Software version: 1.0.0.145954/1.0.0.159292
- EA6500 firmware version: 1.1.28.146072
Thanks for reading my post!

Hey jamay,
Below you'll be able to find the information about the video file I'm trying to stream from my Qnap NAS to my Xbox360.
Note that I'm not actually using the routers USB attached storage / Media Server DLNA features to stream the file, but simply streaming the file from one network device to another. The codec that the video was encoded with won't necessarily apply.
The video does stream okay to my Home PC, but not the Xbox360. My Home PC is using a static IP address, but the Xbox is currently configured to aquire an ip address from the routers DHCP server. I might try and see if using a static IP address will change anything.
Here's the Video File Information:
Format : AVI
Format/Info : Audio Video Interleave
File size : 236 MiB
Duration : 23mn 35s
Overall bit rate : 1 400 Kbps
Video
ID : 0
Format : MPEG-4 Visual
Format settings, BVOP : No
Format settings, QPel : No
Format settings, GMC : No warppoints
Format settings, Matrix : Default (H.263)
Codec ID : DX50
Codec ID/Hint : DivX 5
Duration : 23mn 35s
Bit rate : 1 198 Kbps
Width : 720 pixels
Height : 480 pixels
Display aspect ratio : 3:2
Frame rate : 23.976 fps
Standard : NTSC
Color space : YUV
Chroma subsampling : 4:2:0
Bit depth : 8 bits
Scan type : Progressive
Compression mode : Lossy
Bits/(Pixel*Frame) : 0.145
Stream size : 202 MiB (86%)
Title : Video
Writing library : DivX 5.2.1 Alpha (UTC 2004-09-08)
Audio
ID : 1
Format : MPEG Audio
Format version : Version 1
Format profile : Layer 3
Codec ID : 55
Codec ID/Hint : MP3
Duration : 23mn 34s
Bit rate mode : Constant
Bit rate : 192 Kbps
Channel(s) : 2 channels
Sampling rate : 44.1 KHz
Compression mode : Lossy
Stream size : 32.4 MiB (14%)
Alignment : Split accross interleaves
Interleave, duration : 42 ms (1.00 video frame)
Interleave, preload duration : 500 ms
Title : Audio
Writing library : LAME3.92

Low signals after upgrading TV firmware

I have a UA40D6600WR with an internal WIFI connectivity, after upgrading the company provided firmware last week i see only one bar of Wi-Fi signal strength in Skype app when calling my contacts, due to this I think the contacts video is not clear, wireless router was placed behind the TV. Do we have any workaround for increasing the signal strength in my TV?. Before upgarding the firmware it was working perfectly allright. If we dont have a solution for this please dont upgrade your TV firmware.

nothing??

Choppy video streaming from samba on wireless network

Hey all,
I have a macbook pro with leopard 10.5.7 installed. The server setup is a Linux server running samba which is wired to a wireless router. I connect my macbook pro wirelessly to the router. Everything is all set up; my computer can connect to the server and browse the files without a problem. However, when I try to watch videos stored on my server through samba, the video is extremely choppy and practically unwatchable. I know this is a wireless problem with my macbook pro because my windows desktop has no problems at all watching videos over the wireless connection and when I wire the laptop directly to the router, the video streams just fine i.e, no choppiness. I have browsed the fourms and the internet but no solution has come up yet. I was hoping someone here might have a solution.
Thanks,
schne1derman

Thank God! I thought I was the only one having this problem.
I also have a Ubuntu box with all my movies and I stream videos wirelessly from it to my macbook using XBMC (ubuntu) and Plex (mac). At first I thought the problem was the wireless G speeds from my previous router so I bought an Airport Extreme Base Station and connected it via ethernet to my existing ADSL/Wireless router on a bridge configuration. Both ubuntu and macbook are now connected at 300Mbps but I'm still experiencing occasional choppy video. The wireless connection stays up at all times so it's not a wireless connectivity issue.
I tried NFS but the problem persisted. I also installed Windows 7 RC on my bootcamp partition and had the exact same problem. Which means it can be an issue with the Airport on the macbook. I don't have another computer with Windows so I cannot say if it would work better on a PC.
At first I suspected the problem was with ubuntu so I posted this on the ubuntu forums: http://ubuntuforums.org/showthread.php?p=7324538
As you can see on the description I was getting those messages on the mac logs:
26/05/09 6:02:19 PM KernelEventAgent[198] tid 00000000 type 'smbfs', mounted on '/Volumes/MediaCenter', from '//ed@ed-linux/MediaCenter', not responding
26/05/09 6:02:19 PM KernelEventAgent[198] tid 00000000 found 1 filesystem(s) with problem(s)
26/05/09 6:02:19 PM loginwindow[197] 1 server now unresponsive
At first I thought it was a problem with the arp tables on the mac. I created a static entry for my ubuntu box. Now the connection is better and the samba volume doesn't disconnect as often and when it does, it reconnects after a while. Before the arp table static entry I had to reconnect manually:
26/05/09 6:02:32 PM kernel smbiodreconnect: Reconnected to ed-linux
One other thing to add. Before installing 10.5.7 (i.e running 10.5.6), I had this problem and the video used to get frozen (samba share disconnection) once or twice on a 1 hour video and reconnected 15 to 20 seconds right after it. Not a big deal. Now it happens several times (5 or 6 times on a 30 minute video) and it takes around 30 to 40 seconds to reconnect.
Message was edited by: edvar

WIFI Quit after upgrade to firmware 3.1.

My WIFI quit after upgrading from 2.1.1 to 3.1. It worked twice since the upgrade for a period of an hour or so. I have tried to reset the network, All settings, serveral reinstallation of the firmware. I also Tried to manually enter in my WIFI information, with no success. I tried everything. I can see wifi information when I go into the general settings>About> Wi-Fi Adress 00:1c:b3:48:ce..... My warrenty is no longer valid. Any suggestions???

I've now posted these changes at two other WiFi threads. Try these Settings changes:
The Setting changes are:
Fetch New Data > Push: Off
Fetch settings are set to Manual & in Advanced all is set to Manual.
My iPhone also lost WiFi but with the changes above it now connects though it takes a bit longer to find the signal. No longer have Push but WiFi is more important, to me anyway. Another iPhone user had success with the above changes.
Good luck.

Problem mounting network drive after upgrading router firmware

Hi guys,
It's been a while since I last posted a question of my own here, but I'm at my wits end. As I may have mentioned, I live in France, and my ISP is Free (no, not free, Free...). I've got what they call a "box" here, i.e. a sort of super-modem that will let you connect to the Internet via xDSL (and soon VDSL2), receive hundreds of TV channels, read BluRay discs, store files (videos, music, photos, what have you) on a integrated NAS, place and receive phone calls, whether via a landline (DECT) or, since recently, through a femtocell.
All in all, the package is impressive and works flawlessly. But...
(Of course, there had to be a "but)
... Yesterday, I let my "box" (it's called a Freebox Revolution, or Freebox V6--for Version 6--by the way) upgrade its firmware, reboot as it always does in such circumstances, and since that, the NAS won't mount in the Finder the way it used to under the Shared left pane.
Now, every time I reboot my Mac, I have to open a browser windows and type "smb://mafreebox.freebox.fr" in order mount the NAS in the Finder. I've saved the credentials (login, no password) in the keychain, hoping it would help, but it doesn't. I've got a PC running Windows 8.1 Preview at the moment, and created a shortcut to the NAS on the Desktop. Guess what? I double-click on the shortcut, and sure enough, I can access the content of the NAS from Windows, but not from the Mac.
I must add that I haven't changed anything on the Mac since, or before, upgrading the "box" firmware.
Any ideas?

OK, you must think I'm going bananas, but my issue is gone... For now...
Seriously, what do you guys think about this problem with network drives mounting or not, depending on, I don't know, the weather, maybe?

Problem using Yahoo Video Playlists after upgrading Firefox

I have Created Yahoo playlists in the past and after upgrading my Firefox they no longer work. meaning when i click on a playlist everything loads properly except the video itself and I can't play any of the other videos in the playlist either. Also i can't add new songs to those playlists or rate those videos either.

This is not a Firefox issue, you could try downgrading to version 18 or 17 but Yahoo needs to update their toolbar and they haven't been doing anything to solve issues regarding them except by laying the blame on us.

Web Search fails on E52 after upgrading to firmwar...

After upgrading my E52 to firmware version v31.012, I'm not able to do web search, always fails. When I go back and resend query it works. I still waiting new incoming updates will correct this, but even the v34 didn't resolve this problem. I was able to do search directly when I bought the phone and before v31.012. Did anybody face this problem?

If that message is on your home page and the home page is similar to www.google.com/firefox, then change your home page. The old Firefox/Google home page is no longer being maintained by Google and will give you that erroneous message.
Change your home page to '''''about:home''''', the new built-in, updated Firefox/Google home page
*See --> https://support.mozilla.org/en-US/kb/How%20to%20set%20the%20home%20page
Information submitted with your question indicates that you are using the latest released version, Firefox 10.0.2.
*See --> https://support.mozilla.org/en-US/kb/Finding%20your%20Firefox%20version
'''If this reply solves your problem, please click "Solved It" next to this reply when <u>signed-in</u> to the forum.'''

Has anyone had buffering problems while streaming after upgrading to 7.1?

I have had no problems with streaming content until the iOS 7 upgrade and I had to totally redo my ipad. Now I am having the same problem after upgrading to 7.1. Thanks for any help.

I have Parallels 6, purchased about 10 months ago. It does not work on ML. No support from Parallels. I find this outrageous

Itunes won't detect ipod touch after upgrade to firmware 1.1.4

I am in desperate need of help. My 16GB Ipod is no longer being detected by iTunes.
I decided to upgrade the firmware to 1.1.4. through iTunes. The update wasn't interrupted and i can see no issues during the procedure. when the update was completed, my iPod had no content in it and it wasn't showing up in iTunes.
Here's what i've tried so far to correct this:
- Uninstalled iTunes and all other apple related software and then re-installed
- tried different USB ports on my laptop
- Reset all setting within the ipod
- Run the iTunes diagnostic. It error's out during the sync test.
I've tried to find any other similar example on other sites but haven't been successful.
Please help.

These are other hints http://www.copytrans.net/helpcopytrans.php#22
That might help.

N73 - Another Problem after upgrade the firmware t...

Except the slow contact search problem (solved by Unplug the battery), I still suffered from some application install problems.
1. Whenever I restart the phone, a message 'Installing' always poped up, and the phone not responding for around 2-3 minutes. And then an error message 'Unable to complete ....' prompted.
2. The K-Mobile Client application losted after upgrade, and I tried to reinstall it , but resulted error by 'File corrupted'

Usually that annoying installation process in the beginning can be removed by deleting that installation file in MMC>\Private\10202dce . Most of them does not have the real title of the application. To delete the right one, you need to go to the application manager first and look at the title of the application that cannot be installed nor removed. Ones you know the titles, plug in ur phone to ur computer and browse MMC>\Private\10202dce , some title of the applications from the application manager should be listed there. Delete whatever you find is listed "not installed" in application manager (app cannot be installed or removed), but first make sure to make a backup of it somehow just in case you make an error. After you delete the file/files restart ur phone. The annoying installation process should not appear anymore. Note that by just removing that file may not fully remove the files it created. For advice, if you install applications in ur phone make sure you have backup of them stored in ur computer so that if the installed applications in ur phone stops working properly all you need to do is to reinstall using the original/backup sis files.
- Is this a Signature? -

Choppy video streaming after upgrading E4200 firmware to ver. 1.0.03

Similar Messages

Maybe you are looking for