CIF Problem

Hi,
When I activate the my Integration Model in the R/3 system for transferring the PO and PR I'm getting a dump as <b>Screen output without connection to User</b>.
We have raised an OSS note for this.
Note : We don't get this error always. When we restart the program for the second or thrid time it works perfectly.
Thanks,
Siva.

Hi,
This is typical error you receive when system is trying to transfer Preq/PO from APO to R3
Check following in ERP (R3) system- SPRO--SD side
1.Check for settings mentioned for order types and shipping point determination data
2.If this is intercompany stock transfer PO then check for source/target plant combination with order type
3.If intercompany scenario again then Check if plant is maintained as customer (Plant assigned as customer)
Hope it helps.
Cheers!
Ravi

Similar Messages

Another 7110 CIF problem!

I'm exporting the same file system as a CIF and NFS share.
I have created a file on the CIF share, I can read, write, modify fine.
I get permission denied with trying to modify the same file on the NFS mount. I can see the file, but when I try and do anything with it I get permission denied.
I can't even ls -l on the file - still get permission denied.
We are on 2009.04.10.1.0,1-1.6.
Ta,

Hello,
Are oyu working with NFSv4?
You should have not problems with NFSv3, but with v4 you need to configure identity mapping and the nfsv4 domain.
Sun recommended me to give 777 permissions to the share root and administer the ACLs from the windows if i want to share resources over CIFS and NFS (Active Directory and LDAP authentication).
Regards
Pablo

WAAS / CIFS Problems

Hello all,
We recently deployed WAAS (4.1) system in our datacenter / remote office. The setup is fairly basic from what i'm being told. 2 application accelerators, and one central management device, nothing too tricky. We've opted to use WCCP redirection instead of inline mode.
All WAE's are registered to my CM, the problem i'm running into is at my remote site, after turning on WCCP redirection on my routers, all CIFS file shares stop working between sites. I have file servers at both locations, and after redirecting the traffic to my accelerator, I can no longer access file shares from my remote site to my central office, and vice versa.
The configs are very much default on the WAE's, everything is using automatic discovery, which I was assuming wouldn't cause any problems like this, and I admit that i'm not up to speed on the in's and out's of WAAS.
Any help is appreciated as always!
Thanks -
Jon

Sure:
The servers are Windows Server 2k3, no DFS here at all. These are dell SAN's that we use for storage.
I did see traffic hitting the WAE's, before I stopped redirecting traffic at my remote site, http / https, & domain services & exchange traffic were being optimzed. Basically what happens is after I start redirecting traffic to my remote site WAE's, file shares stop working, so I can't leave them running very long :).
I can post some of the config requests below, but since I'm no longer redirecting traffic to my WAE's, this is going to "skew" the results of the commands.
I did find a post in this forum that said I should upgrade my WAE's to 4.1.5(f), because an MS hotfix KB980232 possibly breaks CIFS accelerated connections. I'm working on downloading & upgrading my accelerators now & will let you know if this fixes my issue.
"We have seen the problems first hand and I would recommend against this patch if accelerating CIFS connections."
http://www.microsoft.com/technet/security/bulletin/MS10-020.mspx
Attached are the show commands you requested.
Thanks!
Jon

CIFS problems after upgrading to eDir 8.8SP5

Dear readers,
I used CIFS for a few months & working OK with WinXP and Win7 (yes I lowered the LM setting); I could connect to all CIFS servers.
I recently installed a new NetWare 6.5SP8 server with eDir 8.8 SP5 (and NMAS 3.3.2) in my companies tree.
I configured CIFS identical to the other servers, but here's the strange part:
When I use my own account I can't connect to the eDir 8.8 SP5 server, with an new (test) account all's working fine; this test -account is in the same context as my own account.
I've upgraded a Netware SP7 server to SP8 and eDir 8.8SP5, I also upgraded an Netware SP7 to eDir 8.8SP5; when running eDir 8.8SP5 it goes wrong.
I'm suspecting NMAS 3.3.2 to create the problem; Servers running NMAS 3.2.0.0 (NW65SP7 eDir 8.7SP3 or 8.8SP4) are well.
I've found in the DSMISC log an error while upgrading SAS:Service, however this would not explain the test account working fine.
Any Ideas?
Thanks in advance,
Erik

Some extra information from a dstrace (NMAS):
test-account:
20:35:01 B35AD420 NMAS: 36: Create NMAS Session
20:35:01 B35AD420 NMAS: 36: NMAS Client supplied user DN test-account.ICT.STAF.ROERMOND.TC
20:35:01 B35AD420 NMAS: ERROR: -1649 Failed to create context for test-account.ICT.STAF.ROERMOND.TC
20:35:01 B35AD420 NMAS: 36: ERROR: -1649 Creating local session for test-account.ICT.STAF.ROERMOND.TC, attempting remote session
20:35:01 B35AD420 NMAS: 36: Actual user DN CN=test-account.OU=ICT.OU=STAF.OU=ROERMOND.O=TC
20:35:01 B35AD420 NMAS: 36: Connected to .CN=IPZSRV38.OU=SRV.OU=ROERMOND.O=TC.T=TC. for remote login
20:35:01 B35AD420 NMAS: 36: .CN=IPZSRV38.OU=SRV.OU=ROERMOND.O=TC.T=TC. NMAS Protocol Version 3.0
20:35:01 B35AD420 NMAS: 36: Remote login will use .CN=IPZSRV38.OU=SRV.OU=ROERMOND.O=TC.T=TC. (NMAS 3.0)
20:35:02 B35AD420 NMAS: 36: Key exchange successful
20:35:02 B35AD420 NMAS: 36: Client address not available to send to remote server
20:35:02 B35AD420 NMAS: 36: Proxy client started remote server session
20:35:02 B35AD420 NMAS: 36: Begin Client Module 0x00000000
20:35:02 B35AD420 NMAS: 36: Client Module 0x00000000 Write
20:35:02 B35AD420 NMAS: 36: Client Module 0x00000000 Read
20:35:02 B35AD420 NMAS: 36: Client Module 0x00000000 Write
20:35:02 B35AD420 NMAS: 36: Client Module 0x00000000 Read
20:35:02 B35AD420 NMAS: 36: Client Module 0x00000000 Finished
20:35:02 B35AD420 NMAS: 36: Connection identity set successfully
20:35:02 B35AD420 NMAS: 36: Client Session Destroy Request
20:35:02 B35AD420 NMAS: 36: Remote Session Destroyed (NMAS_DestroyContext)
20:35:02 B35AD420 NMAS: 36: Destroy NMAS Session
20:35:02 B35AD420 NMAS: 36: Aborted Session Destroyed (with MAF)
own-account:
20:46:03 A6854100 NMAS: 37: Create NMAS Session
20:46:03 A6854100 NMAS: 37: NMAS Client supplied user DN own-account.ICT.STAF.ROERMOND.TC
20:46:03 A6854100 NMAS: ERROR: -1649 Failed to create context for own-account.ICT.STAF.ROERMOND.TC
20:46:03 A6854100 NMAS: 37: ERROR: -1649 Creating local session for own-account.ICT.STAF.ROERMOND.TC, attempting remote session
20:46:03 A6854100 NMAS: 37: Actual user DN CN=own-account.OU=ICT.OU=STAF.OU=ROERMOND.O=TC
20:46:03 A6854100 NMAS: 37: Connected to .CN=IPZSRV38.OU=SRV.OU=ROERMOND.O=TC.T=TC. for remote login
20:46:03 A6854100 NMAS: 37: .CN=IPZSRV38.OU=SRV.OU=ROERMOND.O=TC.T=TC. NMAS Protocol Version 3.0
20:46:03 A6854100 NMAS: 37: Remote login will use .CN=IPZSRV38.OU=SRV.OU=ROERMOND.O=TC.T=TC. (NMAS 3.0)
20:46:03 A6854100 NMAS: 37: ERROR: -1673 NMAS_CanDo: RemoteOpenLoginSession
20:46:03 A6854100 NMAS: 37: Client Session Destroy Request
20:46:03 A6854100 NMAS: 37: Remote Session Destroyed (NMAS_DestroyContext)
20:46:03 A6854100 NMAS: 37: Destroy NMAS Session
20:46:03 A6854100 NMAS: 37: Aborted Session Destroyed (with MAF)

For Purchase order CIF Problem

Hi APO experts
For PO, to change the INCO Terms Fields and this Field has added in User Exit of CIFPUR01 of structure custom Structure CIFPUORCUSe (No other Fields has changed) then CIF the PO INCO Terms Has not updated in APO System..
Suppose If iI change the QTy value then PO Data has updated in APO System ..
Please let me know what is best solutions..
Thanks
Kanth

Hi Vikas,
For INCO Terms fields in not in User exit EXIT_SAPLMEAP_001 (enchancement Name is CIFPUR01 we can add the custom fields in structure CIFPUORCUS I added Custom fields in both systems
My question is suppose if I change the INCO terms only Then CIF won't trigger and IF i change the QTy value then CIFis trigger ...
Please let me know how to do CIF Trigger if I change the INFO Terms no other field..
Thanks,
Kanth

APO GATP Backorder processing -- SO's in R/3 not updating -- CIF problem

Issue: After executing backorder processing in APO, the update is stuck in CIF .. error (*"Inbound APOCLNT800: No IModel active for cat. Sale"*)
Note: I am able to create SO's in R/3 and getting commit from APO.
After Saving the SO's the SO's are transferred to APO ( I am able to see the SO's in product view - APO).
I wonder where is the IM not active
Appreciate your inputs

Hi kitkat,
If this is a test of a new functionality, you might just have an old blocked queue. Try deleting the blocked queue and then re-try the BOP.
If this is a new error for a BOP scenario that had been working previously, then check your deltareport. You may have an order in SCM that for whatever reason is no longer being handled by SCM. In this case, you only need to delete the order in SCM.
If these two tries don't work, then you need to start examining your CIFs to see if the product/location/sales ord/stock/ATP/etc etc are consistant with your expectations. Don't forget, in the case of a GATP using location/product substitution, you need to ensure that all possible data that would be needed by BOP is being properly CIFd across.
Best Regards,
DB49

CIF problem for kmat material

Hello,
I am getting following error message ---
' NO configuration for CONFIGURABLE PPDS-PDS DESKTOP_01' while doing CFM2 transction.
I am working with KMAT ,material with PDS.
kmat material is DESKTOP_01.
We are constructing this scenario.
Please let me know the solution.
Regards,
Ravindra

Hello Uma Maheshwar,
Thank you for your answer.
I have not done the configuration specified by you.
I will do the same.
Please let me know ,
If I am using two classes,
class 300 for parent kmat material and class 001 for the child materials.
Please let me know how can we do the CIF ?
What care must be taken by the doing the cif for materials.
Waiting for your reply.
Regards,
Ravindra

OES2.3 cifs problem

Hi,
CIFS on OES2 SP3.
The user has full rights to this folder and can add or edit files and
folders, however, when trying to back with MS Retail Management System it
fails with:
Dec 21 08:59:45 surely CIFS[10768]: WARNING: CODIR: Error 0,err:168
Dec 21 08:59:45 surely CIFS[10768]: ERROR: CODIR: LockDirCacheEntry failed
Dec 21 08:59:45 surely CIFS[10768]: ERROR: SMB: SMB_ntcreateandx exit,
TID=29, error=1:5 nterror=12
I'm stuck and don't know what to do about it.
Help
Bob Crandell

On Wed, 04 Jan 2012 12:26:02 +0000, AKavitha wrote:
> Hi Bob,
> I managed to setup the RMS trial version and also connect to the Sample
> SQL Server DB that comes along with it.
>
> Could confirm my understanding from the below line in your reply thread:
> "The
> internal RMS backup goes to the server." --> here, does 'server' mean
> the OES Linux or CIFS Server..?
>
> I tried taking a backup by using the DataBase menu option called
> 'BackUp' on the MS-RMS Admin GUI/window.
>
> But this never leads/allows to browse or save the backup to the mapped
> network drive.
>
> Could you please elaborate on the steps on how you were trying to take
> the backup to CIFS server[I need confirmation on this], so this would
> help me in getting closer to the issue you are facing.
>
> Thanks,
> Kavitha A
Novell's CIFS requires OES so it's the same. I guess I don't know what
you are asking.
With our version the very next window that pops up is the browse to the
backup destination. Oh, and here is the exact wording of the error
message:
Cannot open backup device 'M:\MW-RMS\Backup\01042010.bck'. Device error
or device off-line. See the SQL-Server error log for more details.
BACKUP DATABASE is terminating abnormally.
From Event Viewer:
18204 :
BackupDiskFile::CreateMedia: Backup device 'M:\MS-RMS\Backup
\01042012.bck' failed to create. Operating system error = 5(Access is
denied.).
When exiting the RMS Administrator you should get prompted to do a
backup. This also pops up the window to browse to the backup location.
Thanks Kavitha

CIF Problem -- Purchase Orders - Missing in R/3 with External Key

Hi, I have search for OSS Notes on this issue and no luck. When I look in the Error Code (183) in /SAPAPO/CCR. The message specifies
"Schedule line does not exist in R/3
Message no. /SAPAPO/CIF183"
Your input is appreciated.

Hi,
This is typical error you receive when system is trying to transfer Preq/PO from APO to R3
Check following in ERP (R3) system- SPRO--SD side
1.Check for settings mentioned for order types and shipping point determination data
2.If this is intercompany stock transfer PO then check for source/target plant combination with order type
3.If intercompany scenario again then Check if plant is maintained as customer (Plant assigned as customer)
Hope it helps.
Cheers!
Ravi

7310 - Problem with CIFS and Roaming Profiles since upgrade to 2010.Q1.0.2

We have developed a strange problem with our environment which I'm pretty sure is down to the upgrade to 2010.Q1.0.2 from 2009.Q3.4.1 on our 7310 (all the previous 2009 releases had been fine) since nothing else has changed in our environment. I suspect some changes to the underlying CIFS server causing this?
We have virtual Windows servers hosted on a VMWare VSphere cluster which are stored on the 7310 via iSCSI LUNs and also CIFS shares on the 7310 for home directories and separate CIFS shares for roaming profiles - all paths are correct in AD for each user - we also use folder redirection for XP Pro clients to force things like "Application Data", "My Documents" etc. onto the Homedir share.
What we've been seeing recently (which only started happening after the upgrade) is a lot of failed logons to the domain for users. It looks like the usual corrupted profile problem that has plagued Windows forever ...the usual messages that it cannot log the user on with a copy of their roaming profile, and that it will use a temporary one. Some folder redirections (that are initiated via Group Policy) also don't get applied. Users don't see errors when logging off from a "good" profile, and NTUSER.DAT etc. seemingly gets written correctly - the next time they log on, around half the time the users will get these errors as described below:
Event viewer logs show "cannot find the file specified" errors for NTUSER.DAT, along with "directory name is invalid" errors for some of the folder redirections.
More worrying (and what I think might be the real reason for these failures) are the "offline caching is enabled on the roaming profile share" errors. I think that the client-side caching might not be working - possibly the profiles aren't getting flushed and written correctly upon logout?
Now, unfortunately the MMC snap-in for managing shares doesn't seem to support changing the behaviour for client-side caching on the CIFS shares (as confirmed in the latest 7000-series Admin Guide on page 198).
I've been thinking about unchecking the "Enable Oplocks" box which from the CIFS side would completely stop all client-side caching I presume?
Is this likely to be the culprit here, or is there any other known behaviour that could be causing these errors? Is it also worth disabling "Cache device usage" altogether for the Profiles share itself?
Can anyone help? It's a bit of a strange problem, and something I don't want to raise with Sun on our support contract just yet, since at first glance it looks like a Windows problem, but I suspect the storage could well be to blame...

Unfortunately, this is still not working correctly...
So, it looks like it's not related to the offline caching seeing as it all works on the Q2009 despite the warnings...
Some more errors coming out of userenv.log on the affected Windows machines:
USERENV(280.284) 10:07:33:230 ReconcileFile: GetFileAttributes on the source failed with error = 2
USERENV(280.284) 10:07:33:230 CopyProfileDirectoryEx: ReconcileFile failed with error = 2
and later:
USERENV(280.284) 10:07:33:245 GetShareName: WNetGetConnection initially returned error 2250
USERENV(280.284) 10:07:33:245 CopyProfileDirectoryEx: Leaving with a return value of 0
USERENV(280.284) 10:07:33:245 RestoreUserProfile: CopyProfileDirectory failed. Issuing default profile
...which then forces the TEMP profiles.
All other errors linked to this look like "file not found", "invalid path" etc. when the files are present and the paths are correct.
Manually mapping drives using CIFS with UNC paths sporadically fails too now. We have a bunch of GPOs that map shares to users depending on their group memberships - these too are sporadically failing.
It certainly looks to me like it could be a CIFS problem introduced in the Q2010 release.
I'm going to raise a ticket with Sun...

CIF of master data

Hi,
My question is related to the CIF of master data.
I built an integration model to transfer the materials from R/3 to APO, and then the delta modifications are CIF by a background process at night.
I would like to transfer all the delta master data, but having one excetption.
I do not need to transfer the safety stock delta changes in R/3 to APO, so that I maintain these values independently in APO. The issue is that the safety stock values in R/3 are also changed but with another purpose and the R/3 values are overwriting the values that I am uploading directly in APO after the delta CIF transfer.
Is there any way that I can CIF the delta master data changes in R/3, but restricting the delta safety stock changes?
Thanks a lot!

Yes it is possible. You have to add custom logic in the material CIF user exit to turn off the update of safety stock fields in APO. Actually there are a lot of threads in this forum that discuss this issue.
You can start by referring to the thread below
Re: CIF problem with Dynamic and Static Stock Method

I have problem with data transfer between Windows Server 2012RT and Windows7 (no more than 14kbps) while between Windows Sever 2012RT and Windows8.1 speed is ok.

I have problem with data transfer between Windows Server 2012RT and Windows7 (no more than 14kbps) while between Windows Sever 2012RT and Windows8.1 speed is ok.

Hi,
Regarding the issue here, please take a look at the below links to see if they could help:
Slow data transfer speed in Windows 7 or in Windows Server 2008 R2
And a blog here:
Windows Server 2012 slow network/SMB/CIFS problem
Hope this may help
Best regards
Michael
If you have any feedback on our support, please click
here.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

CIF -DeltaReport error 183 schedule line does not exist in R/3

Hi Expert,
In the delta report (/SAPAPO/CCR - CIF_DELTAREPORT), there are discrepancies that say error code 183, which is Schedule line does not exist in R/3..
But when we look in R3, they are actually there. So we don’t want these showing as a discrep in the delta report.
Example in ‘purchasing’, ‘confirmations’, ‘missing in R3 with external key’
If you run DELTAREPORT for purchasing, confirmation, unjustified error 183 are displayed despite of no inconsistency really exists.
Please help why these dscrepancies displayed.
we are running on SCM510.

Hello Maddy
Please go through below SAP notes -
1131469 - DELTAREPORT: unjustified error 181/183 for confirmation
794281 - Locked purchase orders missing from R/3
1022343 - Delta report displays too many errors (181)
817354 - No delete event when you delete orders in APO
Some Old SCN threads -
CCR Error 154 - Planned Order Missing in R3 wit... | SCN
CIF Problem -- Purchase Orders - Missing in R/3 with External Key
This is good document on CCR error handling.
CIF-Comparison / Reconciliation of Transaction Data
Hope this will help.
Thank you
Satish Waghmare

Can't open office files located on a windows server fileshare

Hi TechNet / Office for Mac Community,
re: can't open MS Office files located on a windows server file share
Is anyone else experiencing this issue and/or have a fix?
Details:
Clients: Mac OS X 10.6 / 10.7 / 10.8 / 10.9
File share: Windows Server 2008 R2
Connecting via SMB or CIFS
Problem:
When mounting the Windows Server file share, Mac clients are unable to open MS Office 2011 files (not just powerpoint) from that location.
Error message: "there was an error accessing /Volumes/data/folder/presentation.pptx"
There is no issue creating or deleting MS Office files from that location.
The Mac 'Preview' application is able to open the same MS Office file without issues.
The file is not corrupted and can be opened when copied to the desktop.
Windows clients have no problem opening the file.
Only this particular file share is having an issue.
Are there any known issues or requirements for Windows Server file shares and MS Office 2011 that would apply to this problem?
Your assistance is greatly appreciated.

WebPhoenix, recommend you post this question here instead:
http://answers.microsoft.com/en-us/mac
Thanks,
Mike
Unfortunately your post is off topic here, in the TechNet Site Feedback forum, because it is not Feedback about the TechNet Website or Subscription. This is a standard response I’ve written up in advance to help many people (thousands, really.)
who post their question in this forum in error, but please don’t ignore it. The links I share below I’ve collected to help you get right where you need to go with your issue.
For technical issues with Microsoft products that you would run into as an
end user of those products, one great source of info and help is
http://answers.microsoft.com, which has sections for Windows, Hotmail, Office, IE, and other products. Office related forums are also here:
http://office.microsoft.com/en-us/support/contact-us-FX103894077.aspx
For Technical issues with Microsoft products that you might have as an
IT professional (like technical installation issues, or other IT issues), you should head to the TechNet Discussion forums at
http://social.technet.microsoft.com/forums/en-us, and search for your product name.
For issues with products you might have as a Developer (like how to talk to APIs, what version of software do what, or other developer issues), you should head to the MSDN discussion forums at
http://social.msdn.microsoft.com/forums/en-us, and search for your product or issue.
If you’re asking a question particularly about one of the Microsoft Dynamics products, a great place to start is here:
http://community.dynamics.com/
If you really think your issue is related to the subscription or the TechNet Website, and I screwed up, I apologize! Please repost your question to the discussion forum and include much more detail about your problem, that could include screenshots
of the issue (do not include subscription information or product keys in your screenshots!), and/or links to the problem you’re seeing.
If you really had no idea where to post this question but you still posted it here, you still shouldn’t have because we have a forum just for you! It’s called the Where is the forum for…? forum and it’s here:
http://social.msdn.microsoft.com/forums/en-us/whatforum/
Moving to off topic.
Thanks, Mike
MSDN and TechNet Subscriptions Support

Replaced 2008 DC, now remote systems are slow to browse network

I just replaced our DC that also served as one of several DNS servers. All FSMO roles were transferred to the new DC before demoting.
After doing so, the majority of our remote sites (connected via site-to-site VPN), can no longer access the UNC path of the file server also located in each remote site, and if they can, it is extremely slow. However, this isn't happening to every
remote site. Affected sites are also unable to access UNC path via IP address, although nslookup/pings resolve normally. The temporary workaround is to remove all affected systems from the domain. As soon as those machines are removed from
the domain and rebooted, accessibility to these paths returns instantly.

What did you replace your 2008 DCs with?
Are you using WINS?
Transferring FSMOs wouldn't have anything to do with this. FSMOs are operational role holders that perform tasks for the domain and forest, and do not have anything to do with speed or authentication. However, I've seen slowness occur due to authentication
issues, especially with older operating systems and apps.
I've also seen issues with the TCP Chimney that can cause slowness.
TCP Chimney and RSS Feature May Cause Slow File Transfers or Cause Connectivity Problems
Published by Ace Fekay, MCT, MVP DS on Aug 20, 2009 at 12:44 AM, Updated 10/26/2014
http://blogs.msmvps.com/acefekay/2009/08/19/tcp-chimney-and-rss-features-may-cause-slow-file-transfers-or-cause-connectivity-problems/
And if you replaced the DCs with 2012 or newer, you will also want to inventory your applications to make sure that nothing is using NTLM v1 or LANMAN, which no longer be supported in Windows 2012 R2. So if you have any older apps that are using the
older authentication methods, they may no longer work.
More info:
Understanding Active Directory Domain Services (AD DS) Functional Levels
http://technet.microsoft.com/en-us/library/understanding-active-directory-functional-levels(v=ws.10).aspx
Windows Server 2012 slow network/SMB/CIFS problem
http://jrs-s.net/2013/04/15/windows-server-2012-slow-networksmbcifs-problem/
Ace Fekay
MVP, MCT, MCSE 2012, MCITP EA & MCTS Windows 2008/R2, Exchange 2013, 2010 EA & 2007, MCSE & MCSA 2003/2000, MCSA Messaging 2003
Microsoft Certified Trainer
Microsoft MVP - Directory Services
Complete List of Technical Blogs: http://www.delawarecountycomputerconsulting.com/technicalblogs.php
This posting is provided AS-IS with no warranties or guarantees and confers no rights.

CIF Problem

Similar Messages

Maybe you are looking for