Cintiq 24 HD and dual display turning files black?

I have a brand new Cintiq 24 HD and a secondary monitor, a 24 inch Gateway. Any files I open in Photoshop show up fine on my Cintiq, but as soon as I try and drag them onto the other monitor, they mysteriously turn black. If I drag it back to the Cintiq, I can see it again. Does anybody know why this is happening?

We purchased two new 24" Apple Cinema Displays a few weeks ago along with a new MacBook Pro 15" 2.66GHz. We are using the Cinema Display's built-in mini display port to connect it to the MacBook Pro. Within a few days of setting up the computer, we've encountered the following intermittent faults:
1. Cinema Display flashes black (completely) for a couple of milliseconds;
2. horizontal white lines (1 pixel to 100ish pixels high) flash across Cinema Display.
The MacBook Pro can go for hours with no problem at all and then start a fit of flickering. The MacBook Pro's internal monitor is not affected by any of this. The problem occurs with the MacBook Pro attached to either of the two new Cinema Displays.
We reported the fault and Apple who provided a replacement MacBook Pro. The new computer is doing the exact same thing. We raised it again with Applecare yesterday and installed a Cinema Display firmware update (OS X 10.6.2). The flickering stopped for the rest of the day, but today it's started flickering again!
We also have a one year old MacBook Pro 15" 2.4GHz running OSX 10.5.8 which works perfectly (no flickering or cutouts) with both Cinema Displays.
Apple have now assigned an Engineer to our case and asked us to install some monitoring software (Capture Data / TimingSnoop). I'll update this post if/when Apple resolve the problem.

Similar Messages

My iPhone is flashing the apple logo, and then it turn into black.. And after that, it repeats.. HELP ME

My iPhone is flashing the apple logo, and then it turn into black.. And after that, it repeats.. HELP ME

Hello LaugesenDK
Follow the steps in the article below to put your iPhone into recovery mode and then you should be able to restore your iPhone. If you have a back up you can put your back up to get your data back after it completes it restore process.
If you can't update or restore your iOS device
http://support.apple.com/kb/HT1808
Regards,
-Norm G.

N8 Display turns totally black when incoming call ...

My N8's display always turns totally black when there is an incoming call, or even when the
alarm rings. Before can see the caller's name and answer the call, I have to disable the screen's "keylock".
I tried to find a point in the phone settings wher I can avoid this, but didn't find any. Is anybody out there to give me a hint ?
Thanx in advance

When I am inside, the screen acts normally: it goes black when held close to face. It returns to normal as soon as taken from my face. However, the screen also goes black if I am outside in daytime when I have an incoming call, and when I make calls also, as soon as I press the green call button. It "thinks" it is near my face. If I slide the button on the right side of the phone down twice, the screen lights back up normally but the touch screen will not function. At that point I cannot answer the phone, or if I'm already making a call I cannot hang up nor press the speaker phone button.
There is nothing over the face of the phone. I removed the protective plastic cover but that did not help.
This seems to occur only when I am outside in the sunlight, so it has something to do with a sensor, either light or heat.
I am aware that this problem has occurred on other N8s. I have not found any solutions for it. Perhaps it is not a problem on every N8. I updated the software last week to 111.040.1511 Symbian Belle. That software date is from 2012-07-28.

Bridge and dual displays

I have been searching the web for a while now to find a way to show the usual Bridge window on one display and a preview - just a preview... no menu bar or other embellishments - on the other display in a dual display setup.
Apple's Aperture does it but I can't find a way to do it with Bridge, nor does it appear that Lightroom will do it.
I think this is a significant setback... being able to do this would be great for editing so you could see the image preview with no distractions and as big as possible. More to the point it would be good for presentations so the presenter can see all the folder structure, favourites, thumbnails etc but the audience only sees the intended image on a clean black (yes black... not the image backdrop colour) background.
I have found a way to cheat this, by extending the Bridge window over both displays and positioning all the favourites, folders, thumbnails panels etc on the extreme right side but you still see the menu bar and other bits and bobs at the window edges and the background colour is grey, not black (unless you set the image backdrop to black, which I think is a bit harsh for viewing thumbnails).
If you want to see what I mean, go to http://www.2020graphics.com.au/dual_displays.html
If anyone has any ideas on how to do this, or any Adobe engineers are reading this... help!!!

>Select an image in Bridge. Then hit the space bar on your keyboard.
 
 This is what you get:

Full Screen Preview Space
 nothing but your image on the main monitor, your secondary monitor totally blacked out.
 
 You can use the arrow keys to navigate through the images in the folder. Use the escape key to go back to regular view.
 
 c
<a href="http://www.pixentral.com/show.php?picture=1beW1F4e8DW4i8WW1Y8o1fXztpW" /></a>
<img alt="Picture hosted by Pixentral" src="http://www.pixentral.com/hosted/1beW1F4e8DW4i8WW1Y8o1fXztpW_thumb.jpg" border="0" />
 c Click on thumbnail for original size, then scroll horizontally.
 
 No distractions whatsoever beats Aperture!

10.5.1 and dual display bug

I have been using my MacBook Core Duo (graphics card GMA 950) connected to a projector in dual display mode for over a year. After upgrading from 10.5 to 10.5.1, the macbook can function in mirror mode, but the projector does not receive a signal for dual display unless I restart the computer. The problem is consistent even though the projector has not changed.
Normally I plug in and the laptop screen changes to blue, then changes to dual display mode and sends a signal to the projector. Now, when I connect to the projector, the projector signal is black. I can switch to mirror mode using either F7 or via the Display preferences but there is no way to obtain dual display mode. Once I reboot, the problem is solved. This has been going on daily, each time with the same solution.

I get dozens of the "ACL found but not expected ..." messages, all on the contents of System/Library/User Templates/. When I go to System/Library/ in Finder, only the User Templates folder has a red icon on it, indicating that I do not have access to it (when logged in as an admin). The icon does not appear on any of the other folders in System/Library. Does anyone have any idea on what's going on?
Message was edited by: Rob J.

T410/T510 and Dual Displays

I'm looking at the T410 or T510 for my wife for her business. I wanted to try and set her up with dual displays (either the laptop LCD itself plus one display or two physical displays. Is there anything I need to be aware of in regards to a dock solution or a discrete graphics card if I'm thinking of dual displays?
Solved!
Go to Solution.

1) the integrated only option supports a max of 2 display by itself, so either 2 external LCD and no internal LCD. Or 1 external and 1 internal.
2) the optimus nvidia gpu supports up to 4 LCD.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Mavericks and Dual Display not working as documented

Hi all. Ok..something a little wierder here for my dual display scenario. I have two Samsung Syncmaster 2443 monitors. 15" MBP Retina purchased this year. Running in Clamshell Mode.
I can get dual monitors happening (extended) but I cannot get the menu bar to come over as well. As mentioned in other posts, I need to tick the box in Mission Control "Displays have seperate spaces". The only problem is, that particular menu item is NOT there. All I have is the other 4 items. So how is it that this menu item does not exist on my installation?
In this current setup, each time I reboot the display's also get reveresed, which is really annoying. I have to reboot twice to get back to my original layout.
Any idea's?
Tks

you're faking out your machine to THINK it has 2 real displays and you expect Keynote to work? Keynote is THE most intense app I've ever seen for screen drawing. It basically takes over your entire machine to do its work. It doesn't surprise me that that trick doesn't work with it.
My guess is you're going to have to wait till you have the actual projector and adapter to test your dual screen setup.

Macbook pro 15" and 17" display turns off whilst working then.......

I have 2 macbook pros. One 17" and the other 15" both are the non unibody ones. The 15" had this problem a while ago but my 17" never did it until today and then it did about 5 mins ago.
Whilst I am working (never seems to happen when I am not using it) the display turns off whilst working. The power light remains constant (ie:- not fading in and out when asleep). But here is the strangest thing. The mac repetitively makes the same noise as if it was ejecting a disk. Has anybody else had this? Know a cure? I recently upgraded to snow leopard but don't think this is a software issue.

I got the same problem with mine, 15". I bought it refurbished from apple store. I had this problem when i bought it then nothing happened for 4 months. But now my MBP has started doing it again. And i don't think it's a software issue. My display switch on after few sec, or 1-2 mins it's depends, and it's pretty random. i'm a bit of worry

My Ipad has locked with Itunes logo and cable displayed on a black screen. Cant do anything

My Ipad has locked on a black screen with only the Itunes music logo together with an arrow and a cable white photo display. Turning it on and off achieves nothing, only the Itunes circle and cable appear each time. What can I do to rectify?

I uploaded iOS 7 and the ipad came up with a black screen with pictures of iTunes logo and power cord. It wouldn't turn off or respond to any actions. A terrifying moment. I followed some suggestions from these discussions, connected iPad to Macbook with iTunes open and prayed. It took 3 separate times to completely reset the iPad, because of several "errors" that would occur throughout the lengthy process. This necessity to completely reset my iPad (and it is very shakily alive now, I fear) was a direct result of uploading the new OS. I am furious. What is going on with Apple? I see this has happened to people for quite a while now. Good Lord.
Message was edited by: Liz with the computer genius brother Fred

Port replicator and dual displays

Stupid question alert - if the machine stands straight up in the replicator, how do you use the display in a dual configuration? Also, you still need toplug a USB cable in?

Sorry can you explain what you mean if the machine stands straight up in the replicator? Also, which machine are we talking about here and the model of the port replicator?
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Screen sharing and dual displays

Hi, i added a second display on an iMac and often screen share using my MacBook but since adding the second screen i've had issues screen sharing. It will briefly show both the iMac's displays on my MacBook but then cut out with "connection lost", then find the connection again, then lose it etc etc. Sometimes i can select just the first display and it'll be fine but usually the connection keeps dropping and firing up so quickly that i can't get it to just show the one screen.
I unplugged the second display and everything worked fine as it always has done. Is this a known issue to be resolved in 10.5.3? If not is there a way i can change the default in screen sharing so that it'll just show me the first display? I don't need to see the second display particularly so that doesn't bother me.
Thanks, Simon

It may or may not be a common problem, since I screen share a 2-screen Mac Pro from a MacBook Pro and have not seen this problem. I always get both screens.

T61 and dual displays

Hi there
I have a T61 which a dock and two external monitors connected. HP L2035 (1600x1200) on the DVI and Dell 1907FP on the VGA.
Everything used to work just fine, until some windows update was installed few days ago. Now I can't get the HP display to work.
When I try to change to that monitor via the directorI get the erro:
The following settings you have selected cannot be applied properly. Change the settings and try again. Notebook LCD Resolution Color Quality.
But when I try to change to the HP display via the nview control pana, nothing happens.
I someone else experiencing this?
I have tried to install the latest Precentation Director for the lenovo/ibm site and also the latest NVIDIA drivers for the Quadro NVS 140M.

Yes i had same error but updating presentation director fixed that error. yes i see that you already tested this but i just wanted to tell if this helps someone else.
or maybe you could try this:
-uninstall presentation director
-reboot
-install presentation director
-Remake display profiles to presentation director.
Message Edited by outouser on 06-03-2009 12:09 PM

Nowadays my iMac likes to slow down and its display suddenly goes black. why do these things happen?

I don't know why but a couple of days before, I opened a website and suddenly it became slow. Then the next day when I was opening something which I forgot what it was, and then it went black and I tried every button and suddenly the front row appeared. Today, after I logged in, I opened Safari and then it went black and when I pushed a random button, the log in box appeared. iMac is supposed to be immune to viruses right?

It sounds like you may have a failing hardware component. I would recommend you insert Disk 2 of your Original Installation disks that came with your iMac and boot from it by holding down the Option - D keys, and run the Extended Apple Hardware Test to diagnose what may be failing. It is unfortunately possible that you have an intermitent fault in your hardware that could be tough to find.
Hope this helps

RPT_MOPZ_COPY_STACK_XML shows SC version differs for JAVA and DUAL-Stack xml files

Hi All,
I am using the report/program RPT_MOPZ_COPY_STACK_XML to copy the stack xml file I used from a previous upgraded system. Systems are identical. However, report shows below..
"Software Component Version KRNL64UC7.20 [01200615320200013056] differs between <System1> and <System2>"
and
Software Component Version SAPJVM6.1 [01200615320200012982] differs between <System1> and <System2>"
However, this is not the case when checked, it's strange that this particular component has the same version between the two systems, but the report says they differs in version.
Please help check how to resolve the issue.
SAP notes mentioned in below KBA were already obsolete. Solution Manager system just upgraded to 7.1 SP11.
1711612 - RPT_MOPZ_COPY_STACK_XML Report Troubleshooting.
We would appreciate your response for us to resolve this issue. Thanks.
Regards,
Philip

Hi Jansi, Divyanshu,
Both system have the same patch levels.
Here the situation, SYS1 is where we generated the stack xml file. Afterwards, used that stack file to upgrade SYS1.
Now we built SYS2, ensuring it has the same components version with the un-upgraded version of SYS1, so yes they have same patch number for same components, for this issue, kernel and jvm.
Thus, instead of running MOPZ for SYS2, we used RPT_MOPZ_COPY_STACK_XML to convert the stack file of SYS1 to be used for SYS2.
This is where we encountered below messages, when performing the copy.
"Software Component Version KRNL64UC7.20 [01200615320200013056] differs between <System1> and <System2>"
and
Software Component Version SAPJVM6.1 [01200615320200012982] differs between <System1> and <System2>"
We previously used SOLMAN 7.0 SP23, and the report is working fine there. Then recently, solman was upgraded to 7.1 SP11, and now the report is not working with the above issue.
We would appreciate if you could share actions on how we can fix the issue.
Regards,
Philip

Problem with 10.8; MacPro and dual displays

I have a MacPro with 2 video cards each running a separate Cinema Display. It worked fine with 10.7.
Now with 10.8 the behaviour is very erratic. The displays get L-R reversed. Even when I reset them using System Preferences>Displays and close that (presumably saving the preference), sooner or later, if I do a restart it will reverse back pattern. No particular rhyme or reason to this that I can see. Even physically moving the monitors L<-> Rt doesnt help and sooner or later it changes again. This is a major irritant with 10.8
Any suggestions?

That's a question better suited for Microsoft, but certainly has nothing to do with this forum for the Mac App Store.

Cintiq 24 HD and dual display turning files black?

Similar Messages

Maybe you are looking for