Cisco 1130 status light flashing orange

hello,
I have a question, I have an ap (cisco 1130) that began to get the status light flashing orange and light Ethernet and radio are off.
I did a factory reset and it was ok ... past 3 days the problem has happened again ...
I changed the ap with a new but the situation remained ...
I tested the wiring and everything is ok.
the switch port is set up correctly
may be what??
problem switch??or problem ap??

hello,
I connect the console in to the WAP and then reboot the result of the bootup is as follows:
Xmodem file system is available.
flashfs[0]: 26 files, 8 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 6858240
flashfs[0]: Bytes available: 9140736
flashfs[0]: flashfs fsck took 31 seconds.
Base ethernet MAC Address: 00:24:97:6e:2c:e2
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
link auto-negotiating....
auto-negotiation takes 10000 milli-seconds to complete
ERROR: timeout waiting for auto-negotiation to complete
ERROR: fail to bring ethernet link up
The system has been encountered an error initializing
ethernet port. You may need to check hardware
The system is ignoring the error and continuing boot.
If you interrupt the system boot process, the following
commands will reinitialize ethernet, tftp, and finish
loading the operating system software:
    ether_init
    tftp_init
    boot
Loading "flash:/c1130-k9w8-mx.124-23c.JZ/c1130-k9w8-mx.124-23c.JZ"...########################################################################################################################################################################################################################################################################################################################################################################################################################################################
File "flash:/c1130-k9w8-mx.124-23c.JZ/c1130-k9w8-mx.124-23c.JZ" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(23c)JZ, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 06-Apr-11 15:01 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
flashfs[1]: 26 files, 8 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15740928
flashfs[1]: Bytes used: 6858240
flashfs[1]: Bytes available: 8882688
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Radio0 present A506 7100 E8000000 A0000000 80000000 3
Radio1 present A506 6700 E8000100 A0040000 80010000 2
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1131AG-E-K9   (PowerPCElvis) processor (revision B0) with 25590K/7168K bytes of memory.
Processor board ID FCZ1317Q102
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 7.0.98.218
1 FastEthernet interface
2 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:24:97:6E:2C:E2
Part Number                          : 73-8962-14
PCA Assembly Number                  : 800-24818-13
PCA Revision Number                  : A0
PCB Serial Number                    : FOC13142PXW
Top Assembly Part Number             : 800-29144-03
Top Assembly Serial Number           : FCZ1317Q102
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1131AG-E-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:05.864: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.480: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:09.066: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:09.154: %LWAPP-3-CLIENTEVENTLOG: Unable to open event log file flash:/event.log
*Mar 1 00:00:09.155: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 0 messages)
*Mar 1 00:00:09.184: status of voice_diag_test from WLC is false
*Mar 1 00:00:11.294: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:11.358: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(23c)JZ, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 06-Apr-11 15:01 by prod_rel_team
*Mar 1 00:00:11.358: %SNMP-5-COLDSTART: SNMP agent on host CC-P2-AP4 is undergoing a cold start
*Mar 1 00:00:11.437: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:00:11.615: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:11.615: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:11.615: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:11.877: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:11.877: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:12.297: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
*Mar 1 00:00:12.615: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:12.615: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:30.265: status of voice_diag_test from WLC is false
*Mar 1 00:00:30.308: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:00:40.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:00:41.348: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
*Mar 1 00:00:50.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:00.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:10.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:14.626: %CDP_PD-4-POWER_OK: Full power - NON_CISCO-NO_CDP_RECEIVED inline power source
*Mar 1 00:01:14.665: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:01:14.703: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:01:15.627: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:01:15.665: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:01:20.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:30.348: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:30.348: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:01:40.356: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:01:50.356: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:00.356: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:10.356: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:20.356: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:20.356: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:02:30.359: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:40.359: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:02:50.359: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:00.359: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:10.359: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:10.359: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 00:03:20.362: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
*Mar 1 00:03:30.362: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
I was checking another thing, usually the switches we use here in my work supports a maximum of 14W per port or 15.4w, this wap is consuming 15.2w
Is this the problem??
the strange to me is that,in this same sw I have several WAP and they all use 12.2w
The device type in sw for WAP usually appears as LAP1131AG-AIR-E-K9 ... but this WAP appears as Ieee PD ...
What problems do you think is it?

Similar Messages

ITunes wont open and status light flashs orange. PLEASE HELP!!

I turned on my computer and plugged it in after loging into Windows XP. iTunes wouldnt open and when I tryed to click it open it wouldnt work. I then safely took out my Shuffle and restarted my computer. Then repented the above process and no luck. Can someone please help me?

Try the new shuffle reset tool.
http://docs.info.apple.com/article.html?artnum=303979

My airport time capsule did not set up successfully, and then status light flash amber

Hi, Guys
I am the first time user of the time capsule, please help how to proceed?
I have set up the first time and my airport time capsule does not set successfully, then I try to reset to factory setting. After this, although I use the ethenet cable to connect the router to the airport, the status light flash amber, always, even after the reset.
Also, I can see that airport time capsule base station from the wireless network when airport is plugged in. However, when I want to access to it.

Thanks for your guidance, but the product is really anoying. First, I am sure that the airpor utilities is 6.3.
and I also follow your instruction that to set the IPv6 as local link mode. But still get the same error as mentioned in my first post.
Therefore, I have tried to use the bridge mode but could not find it, and therefore still can not set it up successfully, even though I reset the factory again(press the reset button 5 secconds at least).

Apple TV loses picture output and status light flashes rapidly after 5 minutes hooked up via HDMI - DVI cable

Apple TV connected to a 2005 50" plasma monitor with DVI input via belekin HDMI to DVI cable. Unit worked perfectly long enough to get it connected to the wireless network and begin the itunes registration process when there was a loss of signal message on the screen from the monitor and the Apple TV status light flashed rapidly and continuously. Reset and reboot yeilded flashing rapid status light and no output detected from the monitor. I contacted support online and was told to return the unit to the apple store. I returned home with another brand new apple tv and connected it in the same manner with exactly the same results. Is there something with the HDMI - DVI interface that is causing this? Are there known issues with the HDMI - DVI connection to Apple TV with older plasma monitors?

The Apple TV doesn't actually support DVI. Some have managed to get it to work others have had varying issues with it.

Status light flashes. Apple on TV.

Been using Apple TV more frequently lately. All of a sudden status light flashing continuously and an apple on the screen. I have unplugged everything for an hour and still no luck. held down menu button and other buttons...no luck. Please help so we can watch Apple TV again! Do I need to "reboot"? If so, how!

Hello Kardsy,
The links below detail how to restore both the 1st generation Apple TV and the 2nd and 3rd generation Apple TVs.
Apple TV (1st generation): How to perform a factory restore
http://support.apple.com/kb/HT3199
Apple TV (2nd and 3rd generation): Restoring your Apple TV
http://support.apple.com/kb/HT4367
Cheers,
Allen

3 status lights flash rapidly only after unplugging it stop

Whenever I use Airport setup assistant to make changes to my existing setting, and when the base station should be restarted it stops sending a signal and then all three status lights flash rapidly and also simultaneously. This is a replacement base station as the previous had its wan port fried. When it was first plugged in it gave this same problem. Only after plugging out the power chord and waiting for say 1 minute, then plugging it back in did the flashing stop and the base station started sending a signal again. This also occurred during the first set up using airport admin utility. It hasnt happened since (when using admin utility)but continues to happen when I use airport setup assistant. Is it sumthing I should be worried about?

Sounds like your Airport Base Station is operating just fine - I wouldn't worry about it.

AP Express status light flashing amber for no apparent reason, network works fine

AP Express status light flashing amber for no apparent reason, network works fine, any ideas?

It flashes amber when there is some kind of conflict. If the internet is working but the amber light bothers you, airport utility ahould tell you why your airport is reporting a problem.
If airport utility thinks your airport is normal and the amber light bothers you, do a hard reset on the device

HT204492 If you're using the paired remote and the Apple TV status light flashes white, the problem isn't with the remote.

If you’re using the paired remote and the Apple TV status light flashes white, the problem isn’t with the remote.
Then what is the problem since I have troubleshoot my remote, it is working but cannot do anything on apple TV?

If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
Connect the micro USB cable to the Apple TV and to your computer.
Reconnect the power cable (only for Apple TV 3)
Open iTunes.
Select your Apple TV in the Devices list, and then click Restore.
(You may already have a micro USB cable if you have a camera or other digital device)

Magsafe light flashes orange/green

I've just bought a used MBP 2.2 MHZ which operates fine except for switching back and forth between charging modes when the battery is around 85% full. The magsafe light stays orange a few seconds, then shows green for a second, then back to orange; the charging indicator on the screen switches at the same time. I swapped to a known working magsafe charger - same result. Operating on battery power is also a bit strange, with the available percentage of battery jerking around. Looking around, I see some 2007 and 2008 threads about this issue, but no final resolution at that time. Is there now a "bottom line" to this problem? Thanks!

No, it's not a battery calibration issue - but it could be a bad battery. The flashing MagSafe is a hardware issue. Since the SMC is the controller for power systems, resetting it is about all you can do for 'software' type of fix. If that doesn't correct it, the problem is either with the adapter itself (which you apparently ruled out), with the battery, or with an internal component (more likely the left I/O board, but possibly also the logic board itself).
The fact that your available percentage jumps around points to a deeper problem (time remaining can jump around depending on system load, but % charge should go in only one direction when running on battery).
Given your symptoms, I'd be inclined to try a replacement battery first, before looking inside the case for a problem.
If there's an Apple Store near you, make a Genius Bar appointment and let them have a look - they will be able to test the battery as well.
If you like, post your Full Charge Capacity and Cycle Count (from Apple menu > About this Mac . More Info > Power) for a preliminary diagnosis...

Home hub 3 broadband light flashing orange & purpl...

Hi,
Broadband has stopped working with a flashing orange & purple broadband light (7 days and counting)
Have phoned bt but they failed to resolve the issue over phone - resetting, power off/on etc. Tried 4 different branded adsl filters, alternative router but still no connection. Only 1 main socket, no extensions connected, doesn't have a test facility(older style socket). Tried 17070 quiet line test - sounds clear. Phone line test reports zero faults.
Details from home hub 3 Broadband > connection tab
Line state: Connected
Data Transmitted/Received (GB): 0.0 / 0.0
Downstream: 7.938 Mbps
Upstream: 448 Kbps
ADSL Settings VPI/VCI: 0/38
Type: PPPoA Modulation: G.992.1 Annex A
Latency type: Interleaved
Noise margin (Down/Up): 16.7 dB / 26.0 dB
Line attenuation (Down/Up): 10.8 dB / 5.0 dB
Output power (Down/Up): 17.9 dBm / 12.4 dBm
FEC Events (Down/Up): 10905 / 0
CRC Events (Down/Up): 11 / 0
Loss of Framing (Local/Remote): 0 / 0
Loss of Signal (Local/Remote): 0 / 0
Loss of Power (Local/Remote): 0 / 0
HEC Events (Down/Up): 31 / 0
Error Seconds (Local/Remote): 121 / 3
Broadband > Internet tab
Connection time: Connecting
I suspect the issue is at the exchange, has bt disconnected me and plugged someone else in? Any thoughts welcome.

you appear to have tried everything suggested by BT for purple/orange flashing constantly and not solved the problem. the help pages then say if that has failed then contact technical support but I would contact the forum mods instead for help
contact mods
can take up to 3 working days for mods to contact you
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Status light flashing

My Apple TV was set up and working fine. I attempted to move it to another TV and now I have a fast flashing status light and no picture. Imoved the device back to the original TV and still have the same problem.

Welcome to the Apple Community.
If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
Connect the micro USB cable to the Apple TV and to your computer.
Open iTunes.
Select your Apple TV in the Source list, and then click Restore.

Broadband light flashing orange. A "copper line fa...

Hi all
on Friday 20/01/12 i was using the internet as normal, no weather problems or anything abnormal happening and then as i woke on Saturday 21/01/12 i noticed my broadband (hub 3) had a blue power light, a blue wireless light but a flashing orange light, i followed the steps on the website and restarted my homehub but the still had the same problem. i then changed the adsl filters still had the same problem even tried changing the adsl lead from the socket to the hub but still had the same problem i tried in 3 extension sockets and then also the main bt openzone socket but the problem was still the same.
i then called the bt help line where they made me re iterate the same proccesses twice of what i had already done to then finally test my line and tell me there was a "copper line fault" and the problem would be reapired by 26/01/12. i recieved the email letting me know i would be able to track the fault however when i tried the "track a fault" link it gave me the error message of that the "Sorry we cant complete your request at the moment due to technical error. Please try again" and since the 21/01/12 i have still not recieved a fault update and after many attempts at "trying again" still unable to track the progress.
The internet is crucial to my work and i need it to be running as soon as possible. i live in an apartment and have asked my neighbours if their phone line isnt working but theirs is still working and mine is the only one that isnt, i can't seem to understand how this has happened and why mine is the only one not working, and now with the phone line and broadband not working, my work will be suffering and the implications of not having the internet will be a big impact.
Is anyone else having a problem with tracking their fault or had this fault before and could offer some guidance?
really need this fault to raised as urgent and not being repaired until 26/01/12 could cripple my work.
Also for the days you are without bt vision, broadband and calls is there a way to gain compensation?
Any help or advice would be brilliant.
Thanks Bradley Kent

Keith_Beddoe wrote:
If you live in an area with good 3G mobile coverage, you could buy a pay as you go broadband dongle.
If the Internet is vital to your work, you should have a backup plan, as some major faults can take weeks to fix.
Good advice for a lot of people.
For me the Internet/email is a hobby/pastime. If it went down for a few days it would be an annoyance/inconvenience to me but thats all, but even i have a Three 3G MiFi wireless modem standing by. Just connect up, top up and go.
toekneem
http://www.no2nuisancecalls.net
(EASBF)

N96 V30.033 Status Light flash

Hi there, I wonder if someone could help me, since the V30 upgrade of the firmware to the N96, the "breathing light" has been renamed to "status light" but it doesn't "double flash" when there is a new notification like a text message or missed call. Is there any way of reinabling this? also I've noticed that the options seem to be inverted. If i click on the status option to toggle on and off that's fine, but if it's set to off, and I choose menu then change, in bring a little table up where you can choose on or off, but when it's set to on, the radio button is in the off selection and vista versa, could this be another bug?
hope someone can help!
dave

hmm it could be possilbe that it is in two parts now and you could also have the notification light option and events that you want your phone to notify you of. i am not sure tho as i do not have this particular phone
You know what I love about you the most, the fact that you are not me ! In love with technology and all that it can offer. Join me in discovery....

Power adaptor light flashing orange to green

starting this morning my power adaptor seems to have an issue. the light keeps flashing back and forth bewteen orange and green. and therefore the computer wont really charge. it will operate plugged in this way though.
last week part of my cord did get damaged. the little bumpy part right next to the plug that goes into the computer. the first little bump of the three somehow came off. there does not seem to be a hole or tear in the cord under where it was though.
what purpose does that section serve? is that what is causing my problem?
any ideas?
my computer is one year and one month old, grrrr no longer under waranty...
~ michelle

Hi Michelle,
Given the sloppy design of the iBook, including its power adapter, I would suggest you bite the bullet and buy a new adapter. Otherwise your iBook's DC board may be damaged.
Resetting the PMU helps, as does unplugging both ends of the pwr adapter, waiting for at least 1 minute and plugging it back in. BUT, since you're sure the cable is broken, GET A NEW ONE!
I had a similar problem with my power adapter for my 3-month old iBook, except that the light would suddenly not turn green at all. The cord and the rest of the adapter were intact. I was lucky I still had 7 months of warranty left and got a new adapter from Apple. So far everything is ok.
Good luck, Michelle!
-Andi, a discontented iBook owner.

Help my AE 5th gen needs hard reset daily. Every am status light blinking orange, I unplug modem and AE and replug and light goes green. Network ok for few hours then needs reset. Any suggestions?

Setup - TWC MODEM w/latest docsis set in ethernet only mode - AE 5th gen create a network mode - cat 6 connection to 2nd gen AE in extend wireless network mode. This setup work great for several months, now 5th gen AE needs to be reset several times a day.

I realized I only used the abbreviation AEB vs. Airport Extreme. Caught this after the 15 minute edit restriction. Added in case folks are searching by Airport Extreme. In addition, the solution I setup is a Roaming Network solution vs. "one network". Enjoy!

Cisco 1130 status light flashing orange

Similar Messages

Maybe you are looking for