Cisco-1131 AG Mesh AP converts to LWAPP

hi,
is there a chance that Mesh APs will not associate with LWAPP imaged Controllers ? is it necessary that both AP and Controller shoud be mesh imaged ?
can we convert them Mesh APs to normal LWAPP mode ?
thanks,
Anvar

Translating "CISCO-LWAPP-CONTROLLER"...domain server (86.51.34.17) (86.51.35.18)
*Nov 22 19:38:05.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.10.11 peer_port: 5246
*Nov 22 19:38:06.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Nov 22 19:38:07.681: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.0.10.11 peer_port: 5246
*Nov 22 19:38:07.682: %CAPWAP-5-SENDJOIN: sending Join Request to 10.0.10.11
*Nov 22 19:38:07.682: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Nov 22 19:38:07.828: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Nov 22 19:38:07.830: %DTLS-5-ALERT: Received WARNING : Close notify alert from 10.0.10.11
*Nov 22 19:38:07.830: %DTLS-5-PEER_DISCONNECT: Peer 10.0.10.11 has closed connection.
*Nov 22 19:38:07.831: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.0.10.11:5246
*Nov 22 19:38:07.876: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Nov 22 19:38:07.876: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Nov 22 19:38:13.957: status of voice_diag_test from WLC is false
AP44d3.cae5.7a20#
AP44d3.cae5.7a20#
*Nov 22 19:38:24.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.0.10.11 peer_port: 5246
*Nov 22 19:38:24.001: %CAPWAP-5-CHANGED: CAPWAP changed state to

Similar Messages

What AP models can be converted to LWAPP ?

I have several 1220's with radiomodules MP21G, and also 1231AG with the MP21G radio. Can anyone confirm that they can be converted to LWAPP ?
Johann Folkestad

Hi Johann
Migration from autonomous access point mode to lightweight mode is possible on these Cisco Aironet access point platforms:
- All 1130AG access points
- All 1240 AG access points
- For all IOS-based 1200 series modular access point (1200/1220 Cisco IOS Software Upgrade, 1210 and 1230 AP) platforms, it depends on the radio:
- if 802.11G, MP21G and MP31G are supported
- if 802.11A, RM21A and RM22A are supported
The 1200 series access points can be upgraded with any combination of supported radios: G only, A only, or both G and A.
- All 1310 AG access points
Access points must be running Cisco IOS Release 12.3(7)JA or later before you can perform the upgrade.
So, for your APs you can do the upgrade if you have the minimum IOS version
Hope this helps

Air-lap-1131-ag-e-k9 convert to autonomous not working

Hi,
i have a air-lap01131-ag-e-k9 that was originally in lightweight mode and configured with a controller, but i am in the process of wanting to convert to autonomous mode, i am having issues with connectivity to the AP from my laptop.
i have followed numerous guides on this forum, i have successfully
downloaded correct firmware
renamed the firmware to .default
placed this in root of tftp server folder
connected laptop via console to view output
connected laptop via Ethernet to Ethernet port of AP
changed static ip on laptop to 10.0.0.2 set subnet mask to 255.255.255.0, default gateway to 10.0.0.1
held reset button on AP when applying power and waiting for radio light to flash red
AP gets a IP address then of 10.0.0.1
But even though both laptop and AP are in the same subnet, i am unable to ping the AP from my laptop and it doesn't start the tftp process
I have disabled firewall etc, and tried with both crossover and straight through cable, it seems there is something missing at this last stage, i even tried on a second laptop but that would not ping either, am i missing something.
i acquired the AP for training purposes to help with studies and so far i have learnt a lot of troubleshooting but i would really love to get past this, any help would be really appreciated.
Kind regards
Sam

Xmodem file system is available.
flashfs[0]: 29 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 7215616
flashfs[0]: Bytes available: 8783360
flashfs[0]: flashfs fsck took 31 seconds.
Base ethernet MAC Address: 00:1e:f7:ed:b5:46
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
button pressed for 20 seconds
process_config_recovery: set IP address and config to default 10.0.0.1
process_config_recovery: image recovery
image_recovery: Download default IOS tar image tftp://255.255.255.255/c1130-k9w7-tar.default
examining image...
%Error opening (no such file or directory)Loading "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"...#########################################################################################################################################################################
File "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:38 by alnguyen
Image text-base: 0x00003000, data-base: 0x0035E440
Initializing flashfs...
flashfs[1]: 29 files, 9 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 7215616
flashfs[1]: Bytes available: 8783360
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
cisco AIR-LAP1131AG-E-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCZ1222Q27A
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:1E:F7:ED:B5:46
Part Number                          : 73-8962-12
PCA Assembly Number                  : 800-24818-11
PCA Revision Number                  : B0
PCB Serial Number                    : FOC122106TU
Top Assembly Part Number             : 800-29144-02
Top Assembly Serial Number           : FCZ1222Q27A
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1131AG-E-K9
Press RETURN to get started!
*Mar 1 00:00:06.280: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Mar 1 00:00:06.289: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:38 by alnguyen
*Mar 1 00:00:07.238: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:08.238: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:09.642: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
*Mar 1 00:00:25.297: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:36.237: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up

Converting to LWAPP (Aironet 1231)

I currently manage 115 Aironet AP1231-G-A-K9 WAP's via WLSE. We had a site assessment done, and they are recommending two wireless controllers for management with Cisco 3500 WAP's with clean air technology. I agree with recommendations, but I do not want to replace 115 access points. Has anyone ever successfully converted the 1231's to LWAPP?
I see there are utilites to accomplish this, but I also see alot of incompatibility post. Any comments/advice is greatly appreciated.
Kind Regards,
John

I am really appreciated for your helps Scott
Here is the output from AP.
*Mar 1 00:00:04.781: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1200 Software (C1200-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:41 by alnguyen
*Mar 1 00:00:05.716: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:06.716: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:23.804: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:23.818: LWAPP_CLIENT_ERROR_DEBUG: lwapp_crypto_init_ssc_keys_and_certs no certs in the SSC Private File
*Mar 1 00:00:23.818: LWAPP_CLIENT_ERROR_DEBUG:
*Mar 1 00:00:23.818: lwapp_crypto_init: PKI_StartSession failed
*Mar 1 00:00:23.990: %SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: FAILED CRYPTO INIT.
*Mar 1 00:00:23.990: %LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.
flashfs[0]: 5 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 1864192
flashfs[0]: Bytes available: 5877248
flashfs[0]: flashfs fsck took 11 seconds.
Reading cookie from flash parameter block...done.
Base ethernet MAC Address: 00:11:bb:f4:2a:f5
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbs, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1200-rcvk9w8-mx/c1200-rcvk9w8-mx"...#########################################################################################################################################################################
File "flash:/c1200-rcvk9w8-mx/c1200-rcvk9w8-mx" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
I currently have 42 APs online now.

Cisco 1131 Cannot Associate to WLC Following WCS Install

Greetings, i have had a small wireless deployment up and running for several months consisting of 3 1131 and a 1242 lightweight ap's registered with a 2106 WLC.
Ive had no problems up until i installed WCS on a separate server for testing, ive added the controller successfully and can see all access points up until a day ago.
Following a re-boot of one of our PoE switches two of the 1132 access points failed to re-register with the controller whilst the other two ap's reconnect without issue.
On the Ap themselves lwapp comes with then goes into cfg mode but fails to pull down the config of the controller and then resets.
The controller is giving the message for one of the Ap's
Aug 06 18:03:34.861 spam_lrad.c:2286 LWAPP-3-RD_ERR4: Invalid regulatory domain 802.11bg:-E 802.11a:-E for AP 00:1d:e5:55:df:1a
Previous message occurred 3 times.
Aug 06 18:03:34.861 spam_lrad.c:8055 LWAPP-3-RD_ERR7: Invalid country code () for AP 00:1d:e5:55:df:1a
I have tried resetting both ap's using the mode button at power on but cant figure out what is causing the issue.
Any help would be appreciated!
Regards

This is the response im getting when i add a DNS entry for the lwapp controller into DNS.
cisco AIR-LAP1131AG-E-K9 (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FCZ1213Q1Z8
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from reload
LWAPP image version 5.1.151.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:1E:7A:BE:63:60
Part Number : 73-8962-12
PCA Assembly Number : 800-24818-11
PCA Revision Number : B0
PCB Serial Number : FOC12112BWJ
Top Assembly Part Number : 800-29144-02
Top Assembly Serial Number : FCZ1213Q1Z8
Top Revision Number : A0
Product/Model Number : AIR-LAP1131AG-E-K9
The name for the keys will be: AP001e.7abe.6360.cisco.com
% The key modulus size is 1024 bits
% Generating 1024 bit RSA keys, keys will be non-exportable...[OK]
Press RETURN to get started!
*Mar 1 00:00:05.344: soap_prepare_new_image_crash: mini ios flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx
*Mar 1 00:00:05.345: set boothlpr to mini ios
*Mar 1 00:00:05.697: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:05.904: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 53 messages)
*Mar 1 00:00:07.990: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:08.992: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:11.955: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(16b)JA, RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Mon 07-Jul-08 18:08 by prod_rel_team
*Mar 1 00:00:11.956: %SNMP-5-COLDSTART: SNMP agent on host AP001e.7abe.6360 is undergoing a cold start
*Mar 1 00:00:12.001: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:27.743: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:27.745: bsnInitRcbSlot: slot 0 has NO radio
*Mar 1 00:00:27.745: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:00:27.763: bsnUnlockDevice: not bring radio up: radio 0 is in admin disable state
*Mar 1 00:00:27.764: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
*Mar 1 00:00:28.272: Logging LWAPP message to 255.255.255.255.
%DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 172.29.255.51, mask 255.255.255.0, hostname AP001e.7abe.6360
Translating "CISCO-LWAPP-CONTROLLER..********************..local"...domain server (172.29.255.25) [OK]
%LWAPP-3-CLIENTEVENTLOG: Did not get vendor specific options from DHCP.
%LWAPP-3-CLIENTEVENTLOG: Did not get log server settings from DHCP.
%SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 started - CLI initiated
%LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER..********************..local
%LWAPP-3-CLIENTEVENTLOG: Controller address 172.29.255.5 obtained through DNS
%CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
%LWAPP-5-CHANGED: LWAPP changed state to JOINEncoding the APType as 0
Encoding the RSSI threshhold as 0
Encoding the APType as 0
Encoding the RSSI threshhold as 0
%LWAPP-5-CHANGED: LWAPP changed state to CFG
Writing out the event log to nvram...
%LWAPP-3-CLIENTERRORLOG: Config Request Timer: did not recieve config response (controller - it-wlc-2106)
%SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: DID NOT GET CONFIG RESPONSE.

Convert APs LWAPP to Autonomous without WLC

How can I convert an Access Point with lightweight version to autonomous without a Controller??
Regards,

Hi Juan Carlos,
No worries my friend, this should work :)
Here is a conversion method;
Reverting the Access Point Back to Autonomous Mode
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps!
Rob

Cisco Prime Infrastructure MESH LINK ISSUE

Hi,
a Customer of us has a trouble with cisco Prime Infrastructure 1.2.0.12 and AP mesh link.
There is an huge database ( i suppose the issue can be here ) and when we display some map ( each floor has about 6 RAP and 24 MAP ) we cannot see the MESH information and link draw.
The only way to dipley them is to disable "refresh from network": this way I'm able to show these link..... until a click before.
What i noticied when all was working fine, after i click to some floor:
1) the software started to show the map with normal color and no mesh info displayed ( just ap and coverage cloud )
2) after few time ( less than 1 second ) the map was becoming a little bit lighter and the mesh info was merged to the map
We are missini the second step
Anyone had the same issue ?
best regards
Luigi
PS: I opened a case with WCS version 6.0 ( same issue ) but, after some months, no risult. The last version working fine was WCS 5.2

Just to add some more informations:
- disabling "refreshj from network" ( building properties ) the link and mesh info are showed
- while I'm on a floor, after some refresh, i loose the mesh link draw and, if i click on an AP, i loose also mesh info in the popup. It' s like, after some refresh, the AP are no more recognized as Mesh ( !?!? )
regards
Luigi

How do I configure a cisco 1131 AP to use WPA2 enterprise and authenticate to Active Directory

I have a Win2008 server set up as a radius server (192.168.32.71) and a stand alone AP (192.168.201.9) The AP is config is below:
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
enable secret 5 $1$IdUV$UvE2IJTNzHX6mW6Mmh3At0
ip subnet-zero
ip domain name TKGCORP.local
ip name-server 192.168.32.71
aaa new-model
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa group server radius rad_eap1
server 192.168.201.9 auth-port 1812 acct-port 1813
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authentication login eap_methods1 group rad_eap1
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
dot11 ssid ka_test
   vlan 201
   authentication open eap eap_methods1
   authentication network-eap eap_methods1
   guest-mode
power inline negotiation prestandard source
username Cisco password 7 112A1016141D
username tkgadmin privilege 15 password 7 022D167B06551D60
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 201 mode ciphers aes-ccm tkip
encryption key 1 size 128bit 7 673B0AA56FCB4E630D8E4856427E transmit-key
encryption mode wep mandatory
broadcast-key change 150
ssid ka_test
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
bridge-group 1
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.201
encapsulation dot1Q 201
no ip route-cache
bridge-group 201
bridge-group 201 subscriber-loop-control
bridge-group 201 block-unknown-source
no bridge-group 201 source-learning
no bridge-group 201 unicast-flooding
bridge-group 201 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption key 1 size 128bit 7 B711059074E30B1E1D4E3EC038BB transmit-key
encryption mode wep mandatory
broadcast-key change 150
speed basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
hold-queue 160 in
interface FastEthernet0.201
encapsulation dot1Q 201
no ip route-cache
bridge-group 201
no bridge-group 201 source-learning
bridge-group 201 spanning-disabled
interface BVI1
ip address 192.168.201.9 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
radius-server local
no authentication eapfast
no authentication mac
nas 192.168.201.9 key 7 010703174F
radius-server attribute 32 include-in-access-req format %h
radius-server host 192.168.32.71 auth-port 1645 acct-port 1646 key 7 0835495D1D
radius-server host 192.168.201.9 auth-port 1812 acct-port 1813 key 7 0010161510
radius-server vsa send accounting
control-plane
bridge 1 route ip
line con 0
line vty 0 4
end

Sorry for the late reply Steve. The link you provided was extremely helpful here is what my config looks like now:
ersion 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
enable secret 5 $1$7vHS$YWCMbrlAgDUayKlOHhMlF1
ip subnet-zero
ip domain name TKGCORP.local
ip name-server 192.168.32.71
aaa new-model
aaa group server radius rad_eap
server 192.168.32.71 auth-port 1645 acct-port 1646
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
dot11 ssid wap_test
   authentication open eap eap_methods
   authentication network-eap eap_methods
   authentication key-management wpa
   guest-mode
   infrastructure-ssid optional
power inline negotiation prestandard source
username Cisco password 7 047802150C2E
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid wap_test
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
speed basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
hold-queue 160 in
interface BVI1
ip address 192.168.201.9 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
radius-server attribute 32 include-in-access-req format %h
radius-server host 192.168.32.71 auth-port 1645 acct-port 1646 key 7 071B245F5A
radius-server vsa send accounting
control-plane
bridge 1 route ip
line con 0
line vty 0 4
end
I get a login screen but it will not let me connect, on my radius server I have it set to allow a group that my username is in. Here are some debugs from when I try to connect to the AP:
ap#debug aaa authentication
AAA Authentication debugging is on
ap#
*Mar 2 01:11:53.284: AAA/BIND(00000006): Bind i/f
*Mar 2 01:11:53.355: AAA/AUTHEN/PPP (00000006): Pick method list 'eap_methods'
*Mar 2 01:11:54.556: %DOT11-7-AUTH_FAILED: Station c0cb.3835.a102 Authentication failed
*Mar 2 01:11:55.280: AAA/BIND(00000007): Bind i/f
*Mar 2 01:11:55.404: AAA/AUTHEN/PPP (00000007): Pick method list 'eap_methods'
*Mar 2 01:11:56.349: AAA/BIND(00000008): Bind i/f
*Mar 2 01:11:56.525: AAA/AUTHEN/PPP (00000008): Pick method list 'eap_methods'
*Mar 2 01:11:57.300: AAA/BIND(00000009): Bind i/f
*Mar 2 01:11:58.070: AAA/BIND(0000000A): Bind i/f
*Mar 2 01:11:58.812: AAA/BIND(0000000B): Bind i/f
*Mar 2 01:12:15.470: AAA/AUTHEN/PPP (0000000B): Pick method list 'eap_methods'
*Mar 2 01:12:15.492: %DOT11-7-AUTH_FAILED: Station c0cb.3835.a102 Authentication failed
ap#undebug all
All possible debugging has been turned off

Cisco 1131 access point status led

Hi
Any one experienced a white light on the status led, its the "ring light" infront of the AP. ive checked on http://www.cisco.com/en/US/docs/wireless/access_point/1130/installation/guide/113h_c4.html where all colours are listed and none point done to white.
ANy ideas?
Thanks

Here's an update on this issue. I have had about a 2% failure rate on my 3502i's due to blue, green, and white light freezing. We sent several unit to Cisco's wireless engineer team in Richfield. They have found the issue and have written a fix and are currently doing testing this weekend. They are sending a senior wireless engineer to my office on Monday morning to apply the fix on the 200 units that we have yet to deploy. This is the bad part: the fix can only be applied through the console port and they won't have this integrated into a controller code until May/June. The good news is they have a fix or will just RMA with no questions. I have a webex with their wireless team to explain exactly what the issue is, but from what I gathered is something to do with the boot loader image and the IBM chip in the unit. I will follow up with you guys on Mon/Tues.
Sent from Cisco Technical Support iPhone App

Guest complaining of dropping signal Cisco 1131

I manage a hotels wireless internet and i get constant complaints from guest saying they are getting kicked off wireless. On for 5 to 10 minutes and then they get " page can't be displayed" then after a few minutes they connect again. Do you see any issues with my config ?
here is my template config...channelization is good andmy site survey shows excellent coverage
! AP1131-1
no service pad
clock timezone GMT -6
clock summer-time GMT recurring
ip domain-name xyz
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname AP1of10
ip subnet-zero
logging on
logging buffered 4096 informational
dot11 vlan-name Management vlan 7
dot11 ssid hooters
vlan 319
authentication open
guest-mode
power inline negotiation prestandard source
no username Cisco
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
no shutdown
ssid hooters
speed 1.0 2.0 5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
no preamble-short
channel 1
station-role root fallback shutdown
rts threshold 2312
rts retries 10
interface Dot11Radio0.319
encapsulation dot1Q 319
no ip route-cache
bridge-group 254
bridge-group 254 subscriber-loop-control
bridge-group 254 port-protected
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
bridge-group 254 spanning-disabled
interface Dot11Radio0.7
encapsulation dot1Q 7 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
shutdown
interface FastEthernet0
no ip address
no ip route-cache
duplex full
speed 100
hold-queue 160 in
interface FastEthernet0.319
encapsulation dot1Q 319
no ip route-cache
bridge-group 254
no bridge-group 254 source-learning
bridge-group 254 spanning-disabled
interface FastEthernet0.7
encapsulation dot1Q 7 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 10.1.1.2 255.255.255.192
no ip route-cache
ip default-gateway 10.1.1.1
ip http server
no ip http secure-server
ip http authentication local
control-plane
bridge 1 route ip
line con 0
login local
transport preferred all
transport output all
line vty 0 4
login local
transport preferred all
transport input all
transport output all
line vty 5 15
login local
transport preferred all
transport input all
transport output all
crypto key generate rsa
1024
end

I don't have any experience with the autonomous APs, but I know on the controllers that I have problemd with my Guest SSIDs that have web authentication only. There is a Session Timeout setting on the controllers that sets the interval for re-authentication.
And when doing web-based authentication, then the user must go through the web-authentication page again for the wireless to work once the session timeout is reached. In my scenario, the web authentication page wouldn't come up unless the user manually disconnected and reconnected (or potentially closed IE and started it again). This gave the appearence that they were disconnected with the page cannot be displayed messages.
But this may not be relevent in your case since it isn't controller based and I'm not sure if you use web authentication.
However, a good test would be to see if the WIRELESS disconnects or if it is just merely that data is no longer passing on the active connection.

Cisco 1252 upgrade from standalone autonomous to LWAPP

Hi All,
Can somebody please guide me through the process of upgrading Cisco 1252 access point from Autonomous to Light Weight
iam attaching show version log which gives information about current IOS
on the access point & its in standalone mode now.
Any help would be greatly appreciated.
Cheers,
Satish

Hi Satish,
These two great threads discuss the methods to make this conversion;
From Steve, Leo and Charles;
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=General&topicID=.ee6e8b8&fromOutline=true&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc2c5c3/0
From Scott and Steve;
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=Getting%20Started%20with%20Wireless&topicID=.ee7c7c3&fromOutline=true&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc2fd83/0
Hope this helps!
Rob

Lwapp 1242ag doesnt show mesh

Hi
I'm using a wlan controller with 1242ag converted to lwapp, i'm trying to enable 5.8 but when i change the from local to bridge the lwapp disapear from controler. Someone told me that the firmware does not support mesh !
I'm folowing the 4402 wlan manual at page 641
Sent from Cisco Technical Support iPhone

Yes it was registered when i change it to bridge
Eduardo
By IPhone
Em 11/10/2011, às 09:22, gstefanick escreveu:
Cisco Support Community
Re: lwapp 1242ag doesnt show mesh
created by George Stefanick in Other Wireless - Mobility Subjects - View the full discussion
Did you add the MAC to mac address filter on the WLC?
Reply to this message by going to Cisco Support Community
Start a new discussion in Other Wireless - Mobility Subjects at Cisco Support Community

Cisco AIR-LAP 1131 reboot in loop

Hi Everyone
I recently had to deploy about 4 cisco 1131 AP's to one of our branch location. When configuring them on the controller, i needed to put them in HREAP mode. As soon as i do that and the AP needs to reboot, it will continue to reboot in a loop and indicate the following:
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
Exception (1100)! Data TLB Miss
SRR0 = 0x005A9048 SRR1 = 0x00029230 SRR2 = 0x0028007C SRR3 = 0x00021230
ESR = 0x00000000 DEAR = 0x025BFB94 TSR = 0x84000000 DBSR = 0x00000000
CPU Register Context:
Vector = 0x00001100 PC = 0x005A9048 MSR = 0x00029230 CR = 0x53000035
LR = 0x0048A8A0 CTR = 0x00000072 XER = 0xA0000040
R0 = 0x00000072 R1 = 0x00CD9790 R2 = 0x00000000 R3 = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7 = 0x000000C3
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11 = 0x00000000
R12 = 0x00CDB580 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000
R16 = 0x0184C8AA R17 = 0x0184C71B R18 = 0x00CDB760 R19 = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23 = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27 = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31 = 0x00003D80
Stack trace:
PC = 0x005A9048, SP = 0x00CD9790
Frame 00: SP = 0x00CD97D0    PC = 0x0048A6A8
Frame 01: SP = 0x00CDB728    PC = 0x004361FC
Frame 02: SP = 0x00CDB740    PC = 0x0042E078
Frame 03: SP = 0x00CDB758    PC = 0x0044880C
Frame 04: SP = 0x00CDB798    PC = 0x0042A280
Frame 05: SP = 0x00CDB7C0    PC = 0x0042AA68
Frame 06: SP = 0x00000000    PC = 0x0018A990
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
St-John-AP1 uptime is 1 minute,
cisco AIR-LAP1131G-A-K9    (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
And this is all it does, and keep loading the image. I already know the recovery procedure to reset it, but i wanted to know how i can put these AP in HREAP without having these issues. In the setup we need, we cannot have those AP be in local mode.
Thanks for any help and consideration .
Regards

Hi Scott
Thanks for replying
here is the full output between loops :
Press RETURN to get started!
*Mar 1 00:00:06.552: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.962: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:09.281: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
*Mar 1 00:00:09.281: %SNMP-5-COLDSTART: SNMP agent on host St-John-AP1 is undergoing a cold start
*Mar 1 00:00:09.303: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:10.027: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:10.303: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:11.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:28.301: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:28.301: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:00:28.323: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
*Mar 1 00:00:29.049: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:29.087: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:29.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:37.564: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.1.3.48, mask 255.255.0.0, hostname St-John-AP1
Translating "CISCO-LWAPP-CONTROLLER.aimfire.net"...domain server (10.1.10.100) [OK]
*Mar 1 00:00:50.821: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Mar 1 00:00:50.822: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 15:49:20.913: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 15:49:21.306: %LWAPP-5-CHANGED: LWAPP changed state to CFG
*Mar 1 15:49:21.351: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Mar 1 15:52:11.000: %LWAPP-5-CHANGED: LWAPP changed sta
15:52:12 UTC Fri Mar 1 2013: Unexpected exception to CPUvector 1100, PC = 0x5A9048 , LR = 0x48A8A0
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
CPU Register Context:
MSR = 0x00029230 CR = 0x53000035 CTR = 0x00000072 XER   = 0xA0000040
R0 = 0x00000072 R1 = 0x00D1EC18 R2 = 0x00000000 R3    = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7    = 0x000000CA
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11   = 0x00000000
R12 = 0x00D20A08 R13 = 0x00000000 R14 = 0x00000000 R15   = 0x00000000
R16 = 0x01851A6A R17 = 0x018518DB R18 = 0x00D20BE8 R19   = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23   = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27   = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31   = 0x00003D80
Writing crashinfo to flash:/crashinfo_20130301-155213
=== Flushing messages (15:52:20 UTC Fri Mar 1 2013) ===
Buffered messages:
*Mar 1 00:00:06.552: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.962: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:09.281: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
*Mar 1 00:00:09.281: %SNMP-5-COLDSTART: SNMP agent on host St-John-AP1 is undergoing a cold start
*Mar 1 00:00:09.303: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:10.027: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:10.303: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:11.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
*Mar 1 00:00:28.301: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:28.301: bsnInitRcbSlot: slot 1 has NO radio
*Mar 1 00:00:28.323: bsnUnlockDevice: not bring radio up: radio 1 is in admin disable state
*Mar 1 00:00:29.049: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:29.087: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:29.442: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:37.564: %DHCP-6-ADDRESS_ASSIGN: Interface FastEthernet0 assigned DHCP address 10.1.3.48, mask 255.255.0.0, hostname St-John-AP1
*Mar 1 00:00:50.821: %LWAPP-5-CHANGED: LWAPP changed state to JOIN
*Mar 1 00:00:50.822: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Mar 1 15:49:20.913: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 15:49:21.306: %LWAPP-5-CHANGED: LWAPP changed state to CFG
*Mar 1 15:49:21.351: %LWAPP-5-CHANGED: LWAPP changed state to DOWN
*Mar 1 15:52:11.000: %LWAPP-5-CHANGED: LWAPP changed state to UP
*Mar 1 15:52:11.055: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
Queued messages:
*Mar 1 15:52:23.534: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging output.
*Mar 1 15:52:11.414: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
Nested exception_rom_monitor call (2 times)
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
Exception (1100)! Data TLB Miss
SRR0 = 0x005A9048 SRR1 = 0x00029230 SRR2 = 0x0028007C SRR3 = 0x00021230
ESR = 0x00000000 DEAR = 0x025BFB94 TSR = 0x84000000 DBSR = 0x00000000
CPU Register Context:
Vector = 0x00001100 PC = 0x005A9048 MSR = 0x00029230 CR = 0x53000035
LR = 0x0048A8A0 CTR = 0x00000072 XER = 0xA0000040
R0 = 0x00000072 R1 = 0x00D1EC18 R2 = 0x00000000 R3 = 0x025CBFF8
R4 = 0x025BFB94 R5 = 0x00000000 R6 = 0x00000001 R7 = 0x000000CA
R8 = 0x000001C8 R9 = 0x00000000 R10 = 0x025CBFF8 R11 = 0x00000000
R12 = 0x00D20A08 R13 = 0x00000000 R14 = 0x00000000 R15 = 0x00000000
R16 = 0x01851A6A R17 = 0x018518DB R18 = 0x00D20BE8 R19 = 0x00000007
R20 = 0x00000001 R21 = 0x00000000 R22 = 0x00000007 R23 = 0x00000001
R24 = 0x0093BA68 R25 = 0x00000000 R26 = 0x00000001 R27 = 0x00000001
R28 = 0x00001FA8 R29 = 0x0094A200 R30 = 0x01C7FE38 R31 = 0x00003D80
Stack trace:
PC = 0x005A9048, SP = 0x00D1EC18
Frame 00: SP = 0x00D1EC58    PC = 0x0048A6A8
Frame 01: SP = 0x00D20BB0    PC = 0x004361FC
Frame 02: SP = 0x00D20BC8    PC = 0x0042E078
Frame 03: SP = 0x00D20BE0    PC = 0x0044880C
Frame 04: SP = 0x00D20C20    PC = 0x0042A280
Frame 05: SP = 0x00D20C48    PC = 0x0042AA68
Frame 06: SP = 0x00000000    PC = 0x0018A990
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
St-John-AP1 uptime is 1 minute, 7 seconds
cisco AIR-LAP1131G-A-K9    (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
flashfs[0]: 40 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 15129600
flashfs[0]: Bytes available: 869376
flashfs[0]: flashfs fsck took 41 seconds.
Base ethernet MAC Address: d8:67:d9:ba:9f:2e
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up
Loading "flash:/c1130-k9w8-mx.124-3g.JA2/c1130-k9w8-mx.124-3g.JA2"...###############################################
File "flash:/c1130-k9w8-mx.124-3g.JA2/c1130-k9w8-mx.124-3g.JA2" uncompressed and installed, entry point: 0x3000
executing...
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1130 Software (C1130-K9W8-M), Version 12.4(3g)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 10-Aug-07 20:44 by kehsiao
Image text-base: 0x00003000, data-base: 0x005AEE20
Initializing flashfs...
flashfs[1]: 40 files, 3 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 15998976
flashfs[1]: Bytes used: 15129600
flashfs[1]: Bytes available: 869376
flashfs[1]: flashfs fsck took 5 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Radio 1 A506 7100 E8000000 A0000000 80000000 3
Radio 0 0 0 0 0 0 2
cisco AIR-LAP1131G-A-K9    (PowerPCElvis) processor (revision B0) with 24566K/8192K bytes of memory.
Processor board ID FTX1632N00D
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from unknown reload cause - reason ptr 0xF, PC 0x5A9048, address 0x0
LWAPP image version 4.1.192.35
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: D8:67:D9:BA:9F:2E
Part Number                          : 73-13304-02
PCA Assembly Number                  : 800-36409-01
PCA Revision Number                  : B0
PCB Serial Number                    : FOC16304BZJ
Top Assembly Part Number             : 800-29582-03
Top Assembly Serial Number           : FTX1632N00D
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1131G-A-K9
Press RETURN to get started!
Also , the switchport is a trunk port, i can definitely try it an access port .

WLC 5508 and Cisco Aironet 1242 LWAPP AIR-LAP1242AG-A-K9

i have deployed wlc 5508 ( image 7.0.98.0 ) with 1262N AP and all 45 AP's are working fine,
at the same site i had AP1242 which i have converted to LWAPP (8 of them), these accesspoint are registerd perfectly with 5508 but non of the radio's are up. i have selected different countries according to the part numbers but unfortunaly non of the radio's are coming up, pleaes help
Sathees

Available:370.0(w) Used:32.4(w) Remaining:337.6(w)
Interface Admin    Oper     Power        Device           Class
                            (Watts)
Fa0/1      auto off           0.0 n/a                  n/a
Fa0/2      auto off           0.0 n/a                  n/a
Fa0/3      auto off           0.0 n/a                  n/a
Fa0/4      auto off           0.0 n/a                  n/a
Fa0/5      auto off           0.0 n/a                  n/a
Fa0/6      auto off           0.0 n/a                  n/a
Fa0/7      auto off           0.0 n/a                  n/a
Fa0/8      auto off           0.0 n/a                  n/a
Fa0/9      auto off           0.0 n/a                  n/a
Fa0/10     auto off           0.0 n/a                  n/a
Fa0/11     auto off           0.0 n/a                  n/a
Fa0/12     auto off           0.0 n/a                  n/a
Fa0/13     auto off           0.0 n/a                  n/a
Fa0/14     auto off           0.0 n/a                  n/a
Fa0/15     auto off           0.0 n/a                  n/a
Fa0/16     auto off           0.0 n/a                  n/a
Fa0/17     auto off           0.0 n/a                  n/a
Fa0/18     auto off           0.0 n/a                  n/a
--More--
Interface Admin    Oper     Power        Device           Class
                            (Watts)
Fa0/19     auto off           0.0 n/a                  n/a
Fa0/20     auto off           0.0 n/a                  n/a
Fa0/21     auto off           0.0 n/a                  n/a
Fa0/22     auto off           0.0 n/a                  n/a
Fa0/23     auto off           0.0 n/a                  n/a
Fa0/24     auto off           0.0 n/a                  n/a
Fa0/25     auto off           0.0 n/a                  n/a
Fa0/26     auto off           0.0 n/a                  n/a
Fa0/27     auto off           0.0 n/a                  n/a
Fa0/28     auto off           0.0 n/a                  n/a
Fa0/29     auto off           0.0 n/a                  n/a
Fa0/30     auto off           0.0 n/a                  n/a
Fa0/31     auto off           0.0 n/a                  n/a
Fa0/32     auto off           0.0 n/a                  n/a
Fa0/33     auto off           0.0 n/a                  n/a
Fa0/34     auto off           0.0 n/a                  n/a
Fa0/35     auto off           0.0 n/a                  n/a
Fa0/36     auto off           0.0 n/a                  n/a
Fa0/37     auto off           0.0 n/a                  n/a
Fa0/38     auto off           0.0 n/a                  n/a
Fa0/39     auto off           0.0 n/a                  n/a
Fa0/40     auto off           0.0 n/a                  n/a
Fa0/41     auto on           15.0 cisco AIR-LAP1242AG Class 3
--More--
Interface Admin    Oper     Power        Device           Class
                            (Watts)
Fa0/42     auto off           0.0 n/a                  n/a
Fa0/43     auto on            5.8 cisco AIR-LAP1242AG Class 3
Fa0/44     auto off           0.0 n/a                  n/a
Fa0/45     auto on            5.8 cisco AIR-LAP1242AG Class 3
Fa0/46     auto off           0.0 n/a                  n/a
Fa0/47     auto on            5.8 cisco AIR-LAP1242AG Class 3
Fa0/48     auto off           0.0 n/a                  n/a

Wlc 2106 problem ( cant connect to 2 lwapp ( 1242 & 1131 ) need advice

Dear All,
could you give me some advice to configure wlc with 2 lwapp,
i did try to used 1 lwapp ( 1242 ag ) and it's work, but when i try to connect with 2 lwapp ( 1242 & 1131 ), i can't associated with lwapp 1131 ag, i did used same configuration for both,
need youd advice and reference guide for this issue.
thanks and regards

Hi Heru,
If both are lwapp aps then they should be able to join 2106 controller. Can you confirm if 1130 is also connected to same subnet where 1242 is connected? Is management subnet/vlan different from the vlan you are connecting your LWAPP APs.
Hope this link should help
http://www.cisco.com/en/US/docs/wireless/controller/4.2/configuration/guide/c42lwap.html#wp1104685
HTH
Ankur
*Pls rate all helpfull post

Cisco-1131 AG Mesh AP converts to LWAPP

Similar Messages

Maybe you are looking for