Cisco 1200 Access Points

Hi,
Is it possible to setup an Aironet 1200 in Root AP mode, where it does DHCP for the Wifi clients and NAT. Where the wired interface is equipped with a public IP?

If your 1200 has two radios, yes.  Otherwise it's either a root or an AP but can't be both (per radio).

Similar Messages

  • Cisco 1200 Access Points as Bridges - Won't work

    I could use some help. I have a pair of Cisco 1200 AP's that I'm trying to use as bridges.
    I have selected one as a Root Bridge, the other as Non-Root. The non-root shows the wireless interface down and the log reveals 'no association'.
    I have verified NO security, identical SSID's, broadcast SSID, no encryption, no WEP, they are sitting 10 feet apart, same channels, etc. etc.
    Can a 1200 access point serve as a bridge?

    I went to Security > SSID Manager and selected the only SSID as the infrastructure SSID and it did nothing. If there is another place to toggle 'Infrastructure SSID' on and off other than by assigning one, I'm unaware of it.
    Any other ideas?
    Thanks.

  • Problem with Cisco 1240AG Access Points

    I have a Cisco 1240AG Access point (P/N ? AIR-LAP1242AG-A-K9).
    It has come in the lightweight mode.
    I just want to know whether I can put it to the autonomous mode.

    Hi Indika,
    Here is a conversion method (look most of the way down the attached doc);
    Reverting the Access Point Back to Autonomous Mode
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
    You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
    Using a TFTP Server to Return to a Previous Release
    Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
    Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
    Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
    Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
    Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
    Step 5 Disconnect power from the access point.
    Step 6 Press and hold MODE while you reconnect power to the access point.
    Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
    Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
    Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
    From this doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
    Hope this helps!
    Rob

  • Cisco 1230 access point a radio lightweight mode

    Will the cisco 1230 access point work in lighweight mode if it is using a radio?

    The 1230 can be upgraded to LWAPP with the A Radio model listed below;
    Solution Requirements
    Migration from autonomous access point mode to lightweight mode is possible on these Cisco Aironet access point platforms:
    All 1130AG access points
    All 1240 AG access points
    For all IOS-based 1200 series modular access point (1200/1220 Cisco IOS Software Upgrade, 1210 and **1230 AP**) platforms, it depends on the radio:
    if 802.11G, MP21G and MP31G are supported
    if 802.11A, RM21A and RM22A are supported
    The 1200 series access points can be upgraded with any combination of supported radios: G only, A only, or both G and A.
    All 1310 AG access points
    From this good doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html
    Hope this helps!
    Rob

  • Any new firmware for the Cisco AP541N access points.

    Do you know if Cisco has come out with any new firmware for the Cisco AP541N access points.

    Latest release is 1.8.0 from Jan 25, 2010:
    http://tools.cisco.com/support/downloads/go/ImageList.x?relVer=1.8.0&mdfid=282790482&sftType=Small+Business+Pro+Wireless+Software&optPlat=&nodecount=2&edesignator=null&modelName=Cisco+AP+541N+Wireless+Access+Point&treeMdfId=278875243&treeName=Wireless&modifmdfid=null&imname=&hybrid=null&imst=null&lr=Y

  • Cisco 1310 Access Point Rommon Mode

    Hello,
    So I have a Cisco 1310 Access Point that is in Rommon mode. I have the image on the Access point but I did not use the archive download command to extract it. When I use the
    tar -xtract flash://c1310-k9w7-tar[1].124-25d.JA2.tar flash:
    command It gets close to the end but doesnt finish saying there isnt enough space. When I try to delete the file using delete flash://
    c1310-k9w7-tar[1].124-25d.JA2 it wont allow me saying I do not have permission. I tried the rmdir command as well but had no luck. It wont allow me to use the tags /f /r for forceful and recursive, it doesnt recognize them. Anyone know how to delete a directory in rommon mode on an the 1310 access point?
    Thanks

    The delete /recursive /force flash:/ is what I use.  You might try to delete these files also:
    ap:delete flash:private-configap:delete flash:private-multiple-fs
    Thanks,
    Scott
    *****Help out other by using the rating system and marking answered questions as "Answered"*****

  • Newbie help with Aironet 1200 access point

    Hello everybody,
    We "inherited" an Aironet 1200 access point with antenna's throughout our building. This was installed by a company that thought they would make money selling Wi-Fi access but now they have gone bankrupt.
    We eliminated their router and installed one of our own, and we have it handing out IP addresses. When I plug it into the Aironet 1200 it works just fine. Users are able to connect wirelessly and access the internet.
    I would like to change the SSID however so that it no longer reflects the now defunct companies name.
    I cannot determine what IP address is assigned to the access point so I can't figure out how to access the management page.
    I tried connecting to the ethernet port via a DB9 to RJ45 cable and hyper terminal. After connecting the cable and powering up the access point I am still unable to connect.
    I realize once I get connected I will probably run into password issues, but I'd like to figure out how to get at least that far.
    Any ideas?

    since ur gonna change the ssid and there is a password...
    1. reset the ap. before plugging power to ap, press hold the mode button for 3 sec or until the led becomes orange or amber, then release.
    2. the ap is reset to default setting with ip address 10.0.0.1
    3. either console or gui the ap and change the bvi to ur preferred ip address.
    4. configure everything else as you want.

  • Configuring N channel on cisco 1252 Access Point

    Hi,
    Can someone help me for configuring N-Series band on Cisco 1252 Access Point in IOS Mode.
    Thanks
    Tabrez

    Firstly you need to use WPA2/AES or OPEN authentication.
    Cisco 802.11n Design and Deployment Guidelines
    http://www.cisco.com/en/US/solutions/collateral/ns340/ns394/ns348/ns767/white_paper_80211n_design_and_deployment_guidelines.html

  • Cisco Wap300 access point

    I own a Cisco Wap300 access point . there are a pc, a netbook and a smartphone in my house. I want to connect to these devices my line of fiber internet with Cisco Wap300 access point. My modem brand and model is "ZTE - Zxhn H168N". This modem has 300 Mbps wireless connection speed. Which settings of access point should I use to work my all devices .
    I'am using Air 2310 wireless adaptor for Pc
    I have a netbook and HTC wildfire S smartphone

    Are you referring to this?:
    http://www.cisco.com/cisco/web/solutions/small_business/products/wireless/300_series_wireless_access...
    or this?:
    http://support.linksys.com/en-apac/support/accesspoints/WAP300N
    It's good if we identify the device first before we get the ball rolling.

  • CISCO Aironet access point - not able to connect by user.

    Hi,
    I have CISCO Aironet access point C1130 in my network , but not able to connect by users, I can see below logs from access point. please help on this.
    Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
    Jun 13 17:50:10.686: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
    Jun 13 17:50:15.678: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:20.544: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
    Jun 13 17:50:20.544: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:24.832: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
    Jun 13 17:50:24.832: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:29.741: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
    Jun 13 17:50:29.741: RADIUS: Fail-over denied to  (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:29.741: RADIUS: No response from (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:29.741: RADIUS/DECODE: No response from radius-server; parse response; FAIL         
    Jun 13 17:50:29.741: RADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL         
    Jun 13 17:50:29.741: dot11_auth_dot1x_parse_aaa_resp: Received server response: FAILOVER_RETRY         
    Jun 13 17:50:29.742: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server response         
    Jun 13 17:50:29.742: Client 5864.6c67.3718 failed: EAP reason 0         
    Jun 13 17:50:29.742: dot11_auth_dot1x_parse_aaa_resp: Failed client 5894.6b37.3518 with aaa_req_status_detail 0         
    Jun 13 17:50:29.742: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,SERVER_FAIL) for 5894.6b37.3518         
    Jun 13 17:50:29.742: dot11_auth_dot1x_send_response_to_client: Forwarding server message to client 5894.6b37.3518         
    Jun 13 17:50:29.742: dot11_auth_dot1x_send_response_to_client: Started timer client_timeout 30 seconds         
    Jun 13 17:50:29.743: dot11_auth_dot1x_send_client_fail: Authentication failed for 5894.6b37.3518         
    Jun 13 17:50:29.743: %DOT11-7-AUTH_FAILED: Station 5894.6b37.3518 Authentication failed
    Regards,       

    Hi Niham,
    You can try few things to troubleshoot this -
    1. check the reachability of Radius server from your wlc (ping).
    2. verify the IP address of Raduis server configured on wlc.
    3. wlc in the Radius server ?
    4. Shared Secret must be same on wlc and in raduis server.
    Plz do not forget to rate useful post.
    Thanks

  • Bootup order on Cisco Aironet Access Points

    Hello folks 
    Could you please help me in clarifying the bootup order on Cisco Aironet Access Points 
    Does the SNMP Agent on the device start before the Startup config is copied to Running Config ?
    Because everytime the Cisco Aironet Access Point restart , SNMP trap  is generated from Admin down WLAN interfaces (Dot11Radio1/Dot11Radio0) mentioning "Administratively down " . 
    So my best assumption is that 
    Access point Restarts - > SNMP Engine starts -> Startup Config is copied to Running config -> Interface is made admin down -> SNMP Trap is sent 
    Is that correct?
    Please help !
    Anup

    The Clean Access Manager (CAM) manages out-of-band Clean Access Servers (CASs) and switches through the admin network. The trusted interface of the CAS connects to the admin/management network, and the untrusted interface of the CAS connects to the managed client network.
    When a client connects to a managed port on a managed switch, the port is set to the authentication VLAN and the traffic to/from the client goes through the Clean Access Server. After the client is authenticated and certified through the Clean Access Server, the port connected to the client is changed to the access VLAN. Once on the access VLAN, traffic to and from certified clients bypasses the Clean Access Server.
    In most OOB deployments (except L2 OOB Virtual Gateway where the Default Access VLAN is the Access VLAN in the Port profile), the client needs to acquire a different IP address from the Access VLAN after posture assessment.
    For Real-IP/NAT-Gateway setup, the client port is bounced to prompt the client to acquire a new IP address from the admin/access VLAN.
    The below URL describe the configuration steps needed to set up your OOB deployment:
    •Configure Your Switches
    •Configure OOB Switch Management in the CAM
    •Configure Access to Authentication VLAN Change Detection
    http://www.cisco.com/en/US/docs/security/nac/appliance/configuration_guide/416/CAM/m_oob.html#wp1175744

  • Cisco 2602 Access Point - Support

    Dear Team,
    Could you please advise, if Cisco 2602 Access Point supports IPS and CleanAir along with Access Point feature or does it need to work as standalone to have these functions enabled ?
    Regards,
    SID 

    Might as well add my 2¢
    In order to have CleanAir, you need a WLC.  In order to do IPS, wireless its called wIPS, you need an MSE and NCS or Prime Infrastructure.
    A standalone access point (autonomous) is just a dumb AP and can't perform any of those functions:)
    Thanks,
    Scott
    Help out other by using the rating system and marking answered questions as "Answered"

  • Mac mini not keeping connection with Cisco wireless access point

    I am trying to get my wife's Mac Mini to keep it's connection with the wireless network at her school. They are using a Cisco access point (not sure of the model) which works fine with my G4 Powerbook and the numerous Macbooks being used there, but for some reason her Mac Mini drops the connection after 4 or 5 minutes, at which point she needs to log right off for it to reconnect (as opposed to just turning the card off and on again). I have already gone through the deletion of the Networkinterfaces.plist file, and recreation of the Airport card profile process, but this only kept the interface active for about 36 hours, then it was back to the same old problem. At this point I am thinking "flakey card"...before I ship it off to Apple, can anyone offer any other possible solutions?

    After spending time on the phone with a Apple support technician, he indicated that the Iphone has a compatibility problem with the wep key encryption that the Cisco appliance uses. I find this disturbing being that Cisco is the biggest in network gear. What's UP Apple? We need SP1 for the IPHONE!!!

  • IPhone will not sync with Cisco Wireless Access Point

    This is unbelievable, i just bought a $1000 phone and it wont sync with a Cisco AP. I can sync it with a DLINK? I there a specific list of Access Points it will connect to. If so thats complete bullsh*(. Also, is there going to be a firmware update soon to fix these problems. Can you tell that im a little upset. I just saying that if someone spends $1000 dollars on a phone it should be working pretty dam good. Anyway can someone offer any suggestions?
    Upset Iphone user.

    After spending time on the phone with a Apple support technician, he indicated that the Iphone has a compatibility problem with the wep key encryption that the Cisco appliance uses. I find this disturbing being that Cisco is the biggest in network gear. What's UP Apple? We need SP1 for the IPHONE!!!

  • Cisco wIPS access point query

    Dear All,
    I am planning to install Cisco wIPS in our network, kindly advise if I need to install access point with wireless security module to make my wIPS work or one normal cisco 3602 will be enough. I have gone through the below documents, but one says about wireless module where the other one not says about the module. Kindly suggest.
    http://www.cisco.com/c/en/us/products/collateral/wireless/adaptive-wireless-ips-software/data_sheet_c78-501388.html - Says about module
    http://www.cisco.com/c/en/us/products/collateral/wireless/adaptive-wireless-ips-software/qa_67-503875.html - Not says about module.
    Kindly advise that whether the security module is mandatory to go with Cisco wIPS.
    Regards,
    Jubair.S

    If you want to operate AP normally where client can connect & do wIPS then you require the module.
    Otherwise you can configure AP into monitor mode where it will not associate any clients, but do the wIPS function.
    If you require limited wIPS (Enhanced Local mode) then you can have same AP to do everything. 
    Below summarize the options available & read the given link for more details
    http://www.cisco.com/c/en/us/td/docs/wireless/technology/wips/deployment/guide/WiPS_deployment_guide.html
    HTH
    Rasika
    **** Pls rate all useful responses ****

Maybe you are looking for

  • Edit a single row in af:table

    I am using af:table. In the af:columns I am using a h.Inputtext. Also I have placed one Edit af:command link in starting of every row. At first all the input fields are not editable.( ie I have set the readonly property to true). After click the Edit

  • Trouble with I-Trigue 5600

    Hi, I have bought an I-Trigue 5600 sound system 3 days ago to connect to my onboard CMI 8738 6CH sound card, but i have notested since i installed it that the Center Speaker doesnt work well and only produces noise. Verifyed cables/connections and it

  • Query to find the user is having access to sql server DB

    Hi, Please help me in this. Query to find the whether the user is having access to sql server DB. Cheers, sajith

  • Motion 5.1 will not open nor will the templates created for FCPX

    Every time I try to open Motion I get the beachball, I was able to right click through before on the dock instead because the splash window crashes it. Now it won't open at all. Also, none of the graphics created in motion can be edited in FCPX. Coul

  • PackageMaker (Simple problem I'm sure)

    Hi everyone - Getting my feet wet playing around with PackageMaker, and there's one thing that doesn't make sense to me. How do you install to the "Users" directory without knowing the user's name? I can select a content piece in the left column, and