Cisco 1230 access point a radio lightweight mode
Will the cisco 1230 access point work in lighweight mode if it is using a radio?
The 1230 can be upgraded to LWAPP with the A Radio model listed below;
Solution Requirements
Migration from autonomous access point mode to lightweight mode is possible on these Cisco Aironet access point platforms:
All 1130AG access points
All 1240 AG access points
For all IOS-based 1200 series modular access point (1200/1220 Cisco IOS Software Upgrade, 1210 and **1230 AP**) platforms, it depends on the radio:
if 802.11G, MP21G and MP31G are supported
if 802.11A, RM21A and RM22A are supported
The 1200 series access points can be upgraded with any combination of supported radios: G only, A only, or both G and A.
All 1310 AG access points
From this good doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html
Hope this helps!
Rob
Similar Messages
-
Cisco 1310 Access Point Rommon Mode
Hello,
So I have a Cisco 1310 Access Point that is in Rommon mode. I have the image on the Access point but I did not use the archive download command to extract it. When I use the
tar -xtract flash://c1310-k9w7-tar[1].124-25d.JA2.tar flash:
command It gets close to the end but doesnt finish saying there isnt enough space. When I try to delete the file using delete flash://
c1310-k9w7-tar[1].124-25d.JA2 it wont allow me saying I do not have permission. I tried the rmdir command as well but had no luck. It wont allow me to use the tags /f /r for forceful and recursive, it doesnt recognize them. Anyone know how to delete a directory in rommon mode on an the 1310 access point?
ThanksThe delete /recursive /force flash:/ is what I use. You might try to delete these files also:
ap:delete flash:private-configap:delete flash:private-multiple-fs
Thanks,
Scott
*****Help out other by using the rating system and marking answered questions as "Answered"***** -
Problem with Cisco 1240AG Access Points
I have a Cisco 1240AG Access point (P/N ? AIR-LAP1242AG-A-K9).
It has come in the lightweight mode.
I just want to know whether I can put it to the autonomous mode.Hi Indika,
Here is a conversion method (look most of the way down the attached doc);
Reverting the Access Point Back to Autonomous Mode
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold MODE while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
From this doc;
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
Hope this helps!
Rob -
Configuring N channel on cisco 1252 Access Point
Hi,
Can someone help me for configuring N-Series band on Cisco 1252 Access Point in IOS Mode.
Thanks
TabrezFirstly you need to use WPA2/AES or OPEN authentication.
Cisco 802.11n Design and Deployment Guidelines
http://www.cisco.com/en/US/solutions/collateral/ns340/ns394/ns348/ns767/white_paper_80211n_design_and_deployment_guidelines.html -
Dose access point 1200 aironet lightweight work stand alone
hi
i have question about access point 1200 aironet lightweight
my question is
dose access point 1200 aironet lightweight work stand alone or must connect to controler if its work stand alone how i can disable controller and how i can setup it
thanksYou will need a controller to configured an AP running the LWAPP image. If you need it to run standalone you can convert it to IOS with the process in this document.
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272 -
Any new firmware for the Cisco AP541N access points.
Do you know if Cisco has come out with any new firmware for the Cisco AP541N access points.
Latest release is 1.8.0 from Jan 25, 2010:
http://tools.cisco.com/support/downloads/go/ImageList.x?relVer=1.8.0&mdfid=282790482&sftType=Small+Business+Pro+Wireless+Software&optPlat=&nodecount=2&edesignator=null&modelName=Cisco+AP+541N+Wireless+Access+Point&treeMdfId=278875243&treeName=Wireless&modifmdfid=null&imname=&hybrid=null&imst=null&lr=Y -
I own a Cisco Wap300 access point . there are a pc, a netbook and a smartphone in my house. I want to connect to these devices my line of fiber internet with Cisco Wap300 access point. My modem brand and model is "ZTE - Zxhn H168N". This modem has 300 Mbps wireless connection speed. Which settings of access point should I use to work my all devices .
I'am using Air 2310 wireless adaptor for Pc
I have a netbook and HTC wildfire S smartphoneAre you referring to this?:
http://www.cisco.com/cisco/web/solutions/small_business/products/wireless/300_series_wireless_access...
or this?:
http://support.linksys.com/en-apac/support/accesspoints/WAP300N
It's good if we identify the device first before we get the ball rolling. -
CISCO Aironet access point - not able to connect by user.
Hi,
I have CISCO Aironet access point C1130 in my network , but not able to connect by users, I can see below logs from access point. please help on this.
Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:10.686: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:15.678: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:20.544: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:20.544: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:24.832: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:24.832: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:29.741: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000
Jun 13 17:50:29.741: RADIUS: Fail-over denied to (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:29.741: RADIUS: No response from (20.33.100.11:1645,1646) for id 1645/247
Jun 13 17:50:29.741: RADIUS/DECODE: No response from radius-server; parse response; FAIL
Jun 13 17:50:29.741: RADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL
Jun 13 17:50:29.741: dot11_auth_dot1x_parse_aaa_resp: Received server response: FAILOVER_RETRY
Jun 13 17:50:29.742: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server response
Jun 13 17:50:29.742: Client 5864.6c67.3718 failed: EAP reason 0
Jun 13 17:50:29.742: dot11_auth_dot1x_parse_aaa_resp: Failed client 5894.6b37.3518 with aaa_req_status_detail 0
Jun 13 17:50:29.742: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,SERVER_FAIL) for 5894.6b37.3518
Jun 13 17:50:29.742: dot11_auth_dot1x_send_response_to_client: Forwarding server message to client 5894.6b37.3518
Jun 13 17:50:29.742: dot11_auth_dot1x_send_response_to_client: Started timer client_timeout 30 seconds
Jun 13 17:50:29.743: dot11_auth_dot1x_send_client_fail: Authentication failed for 5894.6b37.3518
Jun 13 17:50:29.743: %DOT11-7-AUTH_FAILED: Station 5894.6b37.3518 Authentication failed
Regards,Hi Niham,
You can try few things to troubleshoot this -
1. check the reachability of Radius server from your wlc (ping).
2. verify the IP address of Raduis server configured on wlc.
3. wlc in the Radius server ?
4. Shared Secret must be same on wlc and in raduis server.
Plz do not forget to rate useful post.
Thanks -
Bootup order on Cisco Aironet Access Points
Hello folks
Could you please help me in clarifying the bootup order on Cisco Aironet Access Points
Does the SNMP Agent on the device start before the Startup config is copied to Running Config ?
Because everytime the Cisco Aironet Access Point restart , SNMP trap is generated from Admin down WLAN interfaces (Dot11Radio1/Dot11Radio0) mentioning "Administratively down " .
So my best assumption is that
Access point Restarts - > SNMP Engine starts -> Startup Config is copied to Running config -> Interface is made admin down -> SNMP Trap is sent
Is that correct?
Please help !
AnupThe Clean Access Manager (CAM) manages out-of-band Clean Access Servers (CASs) and switches through the admin network. The trusted interface of the CAS connects to the admin/management network, and the untrusted interface of the CAS connects to the managed client network.
When a client connects to a managed port on a managed switch, the port is set to the authentication VLAN and the traffic to/from the client goes through the Clean Access Server. After the client is authenticated and certified through the Clean Access Server, the port connected to the client is changed to the access VLAN. Once on the access VLAN, traffic to and from certified clients bypasses the Clean Access Server.
In most OOB deployments (except L2 OOB Virtual Gateway where the Default Access VLAN is the Access VLAN in the Port profile), the client needs to acquire a different IP address from the Access VLAN after posture assessment.
For Real-IP/NAT-Gateway setup, the client port is bounced to prompt the client to acquire a new IP address from the admin/access VLAN.
The below URL describe the configuration steps needed to set up your OOB deployment:
â¢Configure Your Switches
â¢Configure OOB Switch Management in the CAM
â¢Configure Access to Authentication VLAN Change Detection
http://www.cisco.com/en/US/docs/security/nac/appliance/configuration_guide/416/CAM/m_oob.html#wp1175744 -
Cisco 2602 Access Point - Support
Dear Team,
Could you please advise, if Cisco 2602 Access Point supports IPS and CleanAir along with Access Point feature or does it need to work as standalone to have these functions enabled ?
Regards,
SIDMight as well add my 2¢
In order to have CleanAir, you need a WLC. In order to do IPS, wireless its called wIPS, you need an MSE and NCS or Prime Infrastructure.
A standalone access point (autonomous) is just a dumb AP and can't perform any of those functions:)
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
Hi,
I was planning on deploying a couple of 1131AG access points in a standard multiple SSID, multiple VLAN configuration, however, I'm now looking at deploying a single 1142n access point instead.
In our environment we will have 11g, 11a/g and 11n clients. My questions is, in a mixed environmentlike this will the 11n clients be able to take full advantage of the speeds offered by 11n or will they be limited because the AP will have to run in mixed mode?
Thanks
AlyasHi Alyas,
What speed is your uplink? 10/100 or 1Gb? The 1140 has one (1) 1Gb ethernet link. To enable 802.11n, you need to configure WPA2/AES and channel bonding.
Other things to look at are the following:
1. Client saturation per AP - How many clients are concurrently associated to ONE AP? The higher the number the lower the wireless speed. Cisco recommends no more than 25 clients per AP is ideal.
2. Client WLAN NIC and drivers - Are the drivers up-to-date? Do they support 802.11n?
3. The distance of the client from the AP - The further the client(s) are from the AP the lower the speed. The signal strength should be no more than -65 dBm (lower the better) and the signal-to-noise-ratio (SNR) should be 25 dBm (higher the better).
4. What type of traffic? Unicast, multicast or broadcast?
5. Obstacles between the AP(s) and clients - Are there any concrete/cinder block/brick walls? Elevator shafts? Fire escape? Wooden or gyprocks are OK.
6. Radio interference - Other APs transmitting in the same channel as you.
I'd recommend a wireles site survey but with one or two APs it's not worth it.
Hope this helps. -
Can a single Access Point support both bridge mode and Access Point mode at the same time
Hi Guys
Does anyone know which access point can work in both bridge mode and AP mode ?
CheersWell what are you trying to cover. If its really a large outdoor area, then look at the mesh AP. Those require a WLC. Autonomous or stand alone ap can perform bridging on one radio and client access on another. You can also look at AP that support indoor mesh that also controlled by a wlc. If your putting APs outdoors, then look at the outdoor mesh.
Thanks,
Scott Fella
Sent from my iPhone -
Dear All,
I am planning to install Cisco wIPS in our network, kindly advise if I need to install access point with wireless security module to make my wIPS work or one normal cisco 3602 will be enough. I have gone through the below documents, but one says about wireless module where the other one not says about the module. Kindly suggest.
http://www.cisco.com/c/en/us/products/collateral/wireless/adaptive-wireless-ips-software/data_sheet_c78-501388.html - Says about module
http://www.cisco.com/c/en/us/products/collateral/wireless/adaptive-wireless-ips-software/qa_67-503875.html - Not says about module.
Kindly advise that whether the security module is mandatory to go with Cisco wIPS.
Regards,
Jubair.SIf you want to operate AP normally where client can connect & do wIPS then you require the module.
Otherwise you can configure AP into monitor mode where it will not associate any clients, but do the wIPS function.
If you require limited wIPS (Enhanced Local mode) then you can have same AP to do everything.
Below summarize the options available & read the given link for more details
http://www.cisco.com/c/en/us/td/docs/wireless/technology/wips/deployment/guide/WiPS_deployment_guide.html
HTH
Rasika
**** Pls rate all useful responses **** -
My access point version is
cisco AIR-AP1252G-E-K9
and is 802.11 g/n
i am sitting very close to the access point but then also i can reach upto 22 Mbps only. I check on my andriod phone the same result.
is there any configuration i have missed??
Thank You,
AzeemDepends on the wireless clients, the radio used (802.11a or 802.11b), data rates, distance from the AP, interference.
Too many factors to mention. -
PoE auto switchover with Cisco 1252 Access Point.
Dear All
I have a network for Managed Wireless using Cisco. This is a new network for me.
I am in problem with Cisco Access Point 1252. My AP's are connected to a PoE Switch. And Cisco AP's are also connected Powered with also Power Adapter with UPS backup.
But problem is if I disconnect power source of AP Power Adapter , AP is not getting up with PoE. PoE is up only when POWER PLUG of AP ADAPTER is physically pulled out from Socket.
Question is if it is possible to make automatic Failover by PoE when Power source of AP ADAPTER is down ?? I mean no need to PULL OUT POWER PLUG of AP ADAPTER.
Waiting for your rely.
It is very urgent .
Thanking You
Subrun.Hi Suburn,
1- yes it is possible to do failover without unlupping the cable of AC adapter. When power on ACS adapter is off, then the faiolver happens.
2- with regards to POE, if your switch supporting enhanced POE?
Powering the Aironet 1250 Series Access Point with Cisco Enhanced PoE
Cisco Enhanced PoE was designed for customers who want to install new PoE-enabled technologies that require greater than 15.4W per port to function at full capability, such as wireless technology based on the IEEE 802.11n standard. Cisco Enhanced PoE provides the full power requirements for dual-radio modules and eliminates the need to run an additional cabling drop or insert a separate power injector. Support for Enhanced PoE is currently available on a variety of Cisco Catalyst® switching platforms. For more information on Enhanced PoE, visit http://www.cisco.com/en/US/prod/switches/epoe.html.
Serge
Maybe you are looking for
-
in the older version of firefox, you were prompted when you were closing multiple tabs. but you were also given the option of saving the current setup so that when you reopened firefox, this current setup would reopen also. how do i make this happen
-
PCUI - open New Window via Button (to call custom URL / HTML viewer)
Hello group, I have followed the "Use CRM PCUI HTML viewer to call a custom URL" in order to create a custom URL to BW web template. However, instead of displaying the URL in a tab (this works fine), I want a Button in the Accounts view to open up a
-
Error while running MM17 Transaction
Hi Frnds, I am doing MM17 Mass transaction Field (MBEW-VPRSV ) , i am changing the price control of a material from V to S then i am getting an error saying that : ELF-WJ-35MM-CSM1 : Messages have been issued: number MASS000484000000. Regards Rakes
-
I had uploaded my IMAC address book to my new itouch. But because of some problems in the address book (lots of quotes around # and email), I had to fix that (using Excel's trim and clean functions. On the IMAC, I deleted all the contacts in the ad
-
E-mail configuration in C#
I am not able to find the general Mail option(gtalk, yahoo, official mail) in the main menu of C3. When Mail is opened , Nokia mail opens and when Start button is pressed, chekcin for updates....... Later communication error. try later error comes.