Cisco 1252 upgrade from standalone autonomous to LWAPP

Hi All,
Can somebody please guide me through the process of upgrading Cisco 1252 access point from Autonomous to Light Weight
iam attaching show version log which gives information about current IOS
on the access point & its in standalone mode now.
Any help would be greatly appreciated.
Cheers,
Satish

Hi Satish,
These two great threads discuss the methods to make this conversion;
From Steve, Leo and Charles;
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=General&topicID=.ee6e8b8&fromOutline=true&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc2c5c3/0
From Scott and Steve;
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=Getting%20Started%20with%20Wireless&topicID=.ee7c7c3&fromOutline=true&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.2cc2fd83/0
Hope this helps!
Rob

Similar Messages

Cisco ASA Upgrade from 7.0(8) to 8.2(1)

Hi, i need to upgrade my 5510 ASA from 7.0(8) to 8.2(1) ( Please note its different query from my last thread)
what i found online is i will have to do this upgrade in sequence, that is
7.0.x -> 7.2.x --> 8.0.x --> 8.2.1
is that correct?
or i will go to 7.1.x first? like this
7.0.x--> 7.1.x -> 7.2.x --> 8.0.x --> 8.1.x--> 8.2.1
Please guide, Also i am assuming, reboot required after every upgrade right?

ok, i found something on another Cisco document. that is what i thought
To ensure that your configuration updates correctly, you must upgrade to each major release in turn. Therefore, to upgrade from Version 7.0 to Version 8.2, first upgrade from 7.0 to 7.1, then from 7.1 to 7.2, and finally from Version 7.2 to Version 8.2 (8.1 was only available on the ASA 5580). "

Cisco Ucs upgrade from 1.4(3m) to 2.1(1a)

hi!!
I need to do an upgrade from 1.4(3m) to 2.1(1a)!
i've 3 chassis 5108 ( 6 fex 2104xp ) with server B200 M2 and B440 M2. i've two Fi 6120Xp in cluster mode.
i've check the prerequisite to upgrade but i've a question about default zoning;
iv'e brocade switch 5300 ( fw v6.4.1 ) attached to Fi 6120xp
i've SAN configured :
i've no other configuration under San Tab.
The documentation says:
"Default Zoning is Not Supported in Cisco UCS, Release 2.1(1a) Onwards.Default zoning has been deprecated from Cisco UCS, Release 2.1(1a) onwards. Cisco has not supported default zoning in Cisco UCS since Cisco UCS, Release 1.4 in April 2011. All storage connectivity that relies on default zoning in your current configuration will be lost when you upgrade to Cisco UCS, Release 2.1(1a) or a later release. We recommend that you review the Fibre Channel zoning configuration documentation carefully to prepare your migration before you upgrade to Cisco
UCS, Release 2.1(1a) or later."
Can i upgrade to 2.1 (

hi!!
I need to do an upgrade from 1.4(3m) to 2.1(1a)!
i've 3 chassis 5108 ( 6 fex 2104xp ) with server B200 M2 and B440 M2. i've two Fi 6120Xp in cluster mode.
i've check the prerequisite to upgrade but i've a question about default zoning;
iv'e brocade switch 5300 ( fw v6.4.1 ) attached to Fi 6120xp
i've SAN configured :
i've no other configuration under San Tab.
The documentation says:
"Default Zoning is Not Supported in Cisco UCS, Release 2.1(1a) Onwards.Default zoning has been deprecated from Cisco UCS, Release 2.1(1a) onwards. Cisco has not supported default zoning in Cisco UCS since Cisco UCS, Release 1.4 in April 2011. All storage connectivity that relies on default zoning in your current configuration will be lost when you upgrade to Cisco UCS, Release 2.1(1a) or a later release. We recommend that you review the Fibre Channel zoning configuration documentation carefully to prepare your migration before you upgrade to Cisco
UCS, Release 2.1(1a) or later."
Can i upgrade to 2.1 (

Problems upgrading from standalone to CC Lightroom

Hi all.
I had a standalone license for Lightroom 5 but subscribed to the Photographer's Bundle to get Photoshop & LR5. When I first installed it I had a couple of issues but since then it has all been fine. However, today my CC Desktop was telling me LR was not installed, even though it obviously was. I removed LR and reinstalled via CC. That's where the problems began. Trying to open the CC version I was just getting "the catalog could not be opened due to an unexpected error". I could not create a new blank catalog at this point to try alternatives, nor open my current catalog. I have now removed the CC version and put back the other version and my current catalog loads just fine. Now CC says LR is Up to Date even though it's on 5.6 not 5.7 and there's no other way to update it.
Anyone any idea what the problem might be?
OS X Yosemite
LR 5.6

All your settings and data is save and will carry over.
If you update to LR 6 (CC 2015) the installer is the same for both versions and you can decide later if you want to license as stand-alone or subscribe to a CC plan.

Where to upgrade to standalone lightroom 6

Where does one go to do the upgrade from standalone lightroom 5 to version 6? I cannot find an upgrade l ink anywhere. Thanks for your help. Gary

Make sure you're not logged into adobe.com.
Go to the Lightroom page.
All the way on the bottom right is a buy link for the standalone version.
Add it to your cart like you're going to buy the full version.
In your cart select modify and change the purchase to an upgrade.

Upgrading 1252s from autonomous to LWAPP

I need to upgrade several 1252s from autonomous to LWAPP.
I have not been able to find the upgrade tool for 1250s or instructions for CLI upgrade.
I wil be using NCS to do final configuration once the APs come online.
Can someone assist?
Thanks,
Kristin

So long as you pull the rcv file for the AP you should be able ti use NCS to do the conversion.
Other than that a standard AP upgrade should work, with the rcv file as well.
Steve
Sent from Cisco Technical Support iPhone App

Upgraded outdoor 1310G bridge from Autonomous to LWAPP

I recently got a pair of outdoor 1310G bridge radios to create a bridge. I upgraded one of the APs from Autonomous to LWAPP so that it could connect to our 4402 controller so that it could be monitored and controlled by it.
Everything looks like it upgraded fine with the upgrade tool never got any errors however the file: Config_18June2009_95613.csv that is suppose to have a hash key so that I can load that into the WCS or directly into the WLC is blank nothing is in that document. So at the moment the AP is not joining up with the WLC. Anybody have any advice?
Thanks,
Ryan

Hi Ryan,
You can run 'debug pm pki enable' when the AP is trying to join to find out the hash key.
-Matt

1252 autonomous to LWAPP

Hi
I can't seem to find the image for upgrading a 1252 from autonomous to LWAPP. Please can someone point me in the right direction?
Many thanks.

Copy this whole link and try it out (pasting isn't exactly making the whole thing one link): http://tools.cisco.com/support/downloads/go/IPCheck.x?defAdv=N&sftAdv=N&image=c1250-rcvk9w8-tar.124-10b.JA3&filepath=/swc/esd/02/crypto/3DES/281235915/guest&filename=c1250-rcvk9w8-tar.124-10b.JA3&advUrl=null&isk=Y&defInd=N&mdfid=281235915&sftType=Autonomous%20To%20Lightweight%20Mode%20Upgrade%20Image&optPlat=&relVer=12.4(10b)JA3&fileId=271159&treeMdfId=278875243&treeName=Wireless
Or search cisco.com for c1250-rcvk9w8-tar.124-10b.JA3
I think this is what you are looking for.

Converting air-sap2602i-s-k9 from autonomous to LWAPP

Hi guys,
    I need your expertise regarding how to convert from autonomous to LWAPP using AIR-SAP2602i-s-k9 with IOS version of ap3g2-k9w7-xx.152.-2.JA.
    I'm following these commands but it is not available
    debug capwap console cli or debug lwapp console cli
I cannot proceed to convert it Did I miss something or the 2600 series doesn't support LWAPP convertion ?
thank you
Erik

Hi Erik,
Those commands aren;t going to work, they're debug commands for a lightweight AP.
Here is the guide to upgrading:
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html
It's pretty simple though, get the lightweight software follow the upgrade tool instructions to load new software.
Though, you have a newer AP so you'd be ok just to load the new software on, if it's only for a small amount this is fine.
Thanks
Chris

Upgrade 1120G from an autonomous to a lightweight accesspoint

Hi!
I have a network consisting of 22 autonomous Aironet 1120G accesspoints. Is it possible to upgarde these to lightweight accesspoints for using with a Cisco WLAN Controller?

Hi Zach,
These AP's can be converted to LWAPP. We did this exact conversion last summer on about 30 1121G's with the LWAPP upgrade tool. Support for the 1121 was added in WLC version 4.0.155.0 Have a look at these related docs;
Software release 4.0.155.0 New Features
LWAPP for Cisco Aironet 1100 Series Access Points (802.11g radio only) Allows the Cisco Aironet 1100 Series Access Point to be upgraded from autonomous access point mode to lightweight mode using the autonomous to lightweight mode upgrade tool.
Note You must install software release 4.0.155.0 on the controller before connecting 1100 series access points to the controller.
http://www.cisco.com/en/US/products/ps6366/prod_release_note09186a00806e8989.html#wp147320
LWAPP Upgrade Tool Troubleshoot Tips
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a008072d9a1.shtml
Access points must run Cisco IOS Release 12.3(7)JA or later before you use the upgrade tool.
System Requirements
You can use the Autonomous to Lightweight Mode upgrade tool to install Cisco IOS Release 12.3(11)JX on these access points:
**All 1100 series access points containing MP21G (802.11g) radios
All 1130, 1230, and 1240 series access points
All modular 1200 series access points running Cisco IOS software and containing these supported radios:
802.11g: MP21G, MP31G
802.11a: AIR-RM21A-x-K9, AIR-RM22A-x-K9
All 1300 series access points in access point mode
http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/b311jx1.html
Cisco has released a free tool called the "Autonomous to Lightweight Mode Upgrade Tool" that allows selected Cisco Aironet autonomous access point models to be configured for lightweight mode operation.
The Autonomous to Lightweight Mode Upgrade Tool supports the following models:
Cisco Aironet 1240AG Series access points
Cisco Aironet 1230AG Series access points
Cisco Aironet 1200 Series access points that contain 802.11g (AIR-MP21G-x-K9) and/or second-generation 802.11a radios (AIR-RM21A-x-K9 or AIR-RM22A-x-K9)
Cisco Aironet 1130AG Series access points
**Cisco Aironet 1100 Series Access Points that contain 802.11g radios (AIR-AP1121G-x-K9)
Cisco Aironet 1300 Series Access Points/Bridges (AIR-BR1310G-x-K9 or AIR-BR1310G-x-K9-R). A Cisco Aironet 1300 Series operating in Lightweight Access Point Protocol (LWAPP) mode only operates as an access point. This series does not support LWAPP bridging mode.
The Autonomous to Lightweight Mode Upgrade Tool supports a process to migrate an autonomous access point from autonomous mode to lightweight mode. Unlike a VxWorks to Cisco IOS Software upgrade, this process is a Cisco IOS Software upgrade to the existing Cisco IOS Software image-not an operating system "swapout". In converted access points operating in lightweight mode, Cisco IOS Software continues to run on the access point, while LWAPP is used to communicate with a wireless LAN controller. Since LWAPP supports automatic access point configuration, there is no need to retain or convert the original autonomous Cisco IOS Software access point configuration.
http://www.cisco.com/en/US/netsol/ns340/ns394/ns348/ns337/networking_solutions_white_paper0900aecd804f1a23.shtml
Cisco Aironet Access Point Support for Lightweight Access Point Protocol
http://www.cisco.com/en/US/products/ps6521/prod_bulletin0900aecd80321a2c.html
Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp157147
Hope this helps!
Rob

Upgrade 1121 autonomous to LWAPP

I have some access-points AIR-AP-1121G-TO-K9 and it would like to use them with a WLAN Controller. Is possible to change IOS for the software LWAPP to use with the WLAN Controller?
I know that that is possible in another models of access-points, but I don't know if the 1121 support that upgrade.
Regards.

Hi Andre,
Just to add a note to the good tips from Ankur. These AP's can be converted to LWAPP. We did this exact conversion last summer on about 30 1121G's with the **LWAPP upgrade tool**.
Support for the 1121 was added in WLC version 4.0.155.0 Have a look at these related docs;
Software release 4.0.155.0 New Features
LWAPP for Cisco Aironet 1100 Series Access Points (802.11g radio only) Allows the Cisco Aironet 1100 Series Access Point to be upgraded from autonomous access point mode to lightweight mode using the autonomous to lightweight mode upgrade tool.
Note You must install software release 4.0.155.0 on the controller before connecting 1100 series access points to the controller.
http://www.cisco.com/en/US/products/ps6366/prod_release_note09186a00806e8989.html#wp147320
LWAPP Upgrade Tool Troubleshoot Tips
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a008072d9a1.shtml
Access points must run Cisco IOS Release 12.3(7)JA or later before you use the upgrade tool.
System Requirements
You can use the Autonomous to Lightweight Mode upgrade tool to install Cisco IOS Release 12.3(11)JX on these access points:
**All 1100 series access points containing MP21G (802.11g) radios
All 1130, 1230, and 1240 series access points
All modular 1200 series access points running Cisco IOS software and containing these supported radios:
802.11g: MP21G, MP31G
802.11a: AIR-RM21A-x-K9, AIR-RM22A-x-K9
All 1300 series access points in access point mode
http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/b311jx1.html
Cisco has released a free tool called the "Autonomous to Lightweight Mode Upgrade Tool" that allows selected Cisco Aironet autonomous access point models to be configured for lightweight mode operation.
The Autonomous to Lightweight Mode Upgrade Tool supports the following models:
Cisco Aironet 1240AG Series access points
Cisco Aironet 1230AG Series access points
Cisco Aironet 1200 Series access points that contain 802.11g (AIR-MP21G-x-K9) and/or second-generation 802.11a radios (AIR-RM21A-x-K9 or AIR-RM22A-x-K9)
Cisco Aironet 1130AG Series access points
**Cisco Aironet 1100 Series Access Points that contain 802.11g radios (AIR-AP1121G-x-K9)
Cisco Aironet 1300 Series Access Points/Bridges (AIR-BR1310G-x-K9 or AIR-BR1310G-x-K9-R). A Cisco Aironet 1300 Series operating in Lightweight Access Point Protocol (LWAPP) mode only operates as an access point. This series does not support LWAPP bridging mode.
The Autonomous to Lightweight Mode Upgrade Tool supports a process to migrate an autonomous access point from autonomous mode to lightweight mode. Unlike a VxWorks to Cisco IOS Software upgrade, this process is a Cisco IOS Software upgrade to the existing Cisco IOS Software image-not an operating system "swapout". In converted access points operating in lightweight mode, Cisco IOS Software continues to run on the access point, while LWAPP is used to communicate with a wireless LAN controller. Since LWAPP supports automatic access point configuration, there is no need to retain or convert the original autonomous Cisco IOS Software access point configuration.
http://www.cisco.com/en/US/netsol/ns340/ns394/ns348/ns337/networking_solutions_white_paper0900aecd804f1a23.shtml
Cisco Aironet Access Point Support for Lightweight Access Point Protocol
http://www.cisco.com/en/US/products/ps6521/prod_bulletin0900aecd80321a2c.html
Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp157147
Hope this helps!
Rob

Autonomous to LWAPP with Cisco Prime 2.2

Hello, I need to know if exist any procedure to convert Autonomous to LWAPP access point with Cisco Prime 2.2.

Here are the Steps Cristian.
To create an autonomous AP migration template, follow these steps:
Step 1 Choose Design > Configuration > Wireless Configuration > Autonomous AP Migration Templates .
Step 2 From the Select a command drop-down list, choose Add Template, then click Go . If you are updating an already existing template, click the applicable template in the Template Name column.
Step 3 Complete the required fields. For information about the field descriptions, see: http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/infrastructure/2-0/reference/guide/prime_infr_ref.html
Step 4 To view the migration analysis summary, choose Operate > Wireless > Migration Analysis .
Note: After an access point has been converted to lightweight, the previous status or configuration of the access point is not retained.
Hope this will resolve your issue ;)

I have just upgraded from Lightroom 5 standalone to Lightroom 6 standalone. I ppear to have been automatically enrolled for a 30 day free trial of Lightroom mobile and Creative Cloud. Reading the FAQ, it appears that after the expiry of the free trial I w

I have just upgraded from Lightroom 5 standalone to Lightroom 6 standalone. I appear to have been automatically enrolled for a 30 day free trial of Lightroom Mobile and Creative Cloud. Reading the FAQ, it appears that after the expiry of the free trial, if I do not sign up and pay, I will only be able to view my pictures on the desktop but not edit them - surely this cannot be true. How do I un-enroll for the 30 day free trial of Lightroom Mobile and CC?

When I was signed into Adobe (which was a requirement for installing the upgrade), Lightroom 6 told my at the top right corner that I had 30 days left of my free trial of Lightroom Mobile and Creative Cloud. In parallel with this forum posting, I am chatting with Adobe support. he is away to find out how to prevent any synching with Creative Cloud during the 30 day free trial. I do not think that Creative Cloud is an application that gets installed on your PC. I think Lightroom 6 has it built in, and can use it if if you are signed up to the Creative Cloud and Lightroom Mobile (which I am for 30 days)

Issues with Clients moving from Autonomous to LWAPP

I have a fairly large wireless rollout of access points at my hospital's main campus and then I have 41 remote sites that have approximately 3 to 10 access points at each location.
My problem is this, I just converted one site from 9 autonomous access point over to LWAPP. The site has a 10 meg metro Ethernet connection so I know its not the link back to me. We have 26 Motion Tablets with Atheros wireless clients at that location that utilize a Citrix application called Logician. We have been having some issues with the Motion tablets holding the Citrix connection, but once we converted this site, those clients have really been having issues.
There is a high density of access points so coverage is not an issue, but I didn't know if anyone else out there may have a similar scenario and could lend some advise as to why the LWAPP causes so many issues.
Thanks in advance.

Hi. LWAPP itself should not cause service to be worse; because of the dynamic nature of its settings, it should actually improve connectivity.
Do these wireless clients have access to any services (e.g. internet) that do not require use of Citrix? If so, how is the performance there? If you're getting consistent, reasonably quick internet access, but your Citrix session keeps failing; it may not be a WLAN issue per se.
I have done several implementations of Citrix over WLAN for hospitals. Most of the time if there are connection interruptions, it boils down to one of two problems.
1.) Interference: Hospitals are very hostile environments for RF. Various building materials, large machinery, and irregular shapes in the floorplan make it difficult for RF to travel consistently.
2.) Citrix settings: Citrix is a highly configurable application. There are session timeout settings which can be tweaked which may make the system more tolerant to momentary lapses in connectivity.
My suggestion would be to see if the issue is limited to Citrix traffic only; and if it is, look at how Citrix is configured. If you're finding sub-par performance with all wireless traffic, then maybe it's an interference issue that keeps knocking you off the WLAN. If that is the case, I would suggest a professional wireless consultant should come in and decide on the best methods for giving you more consistent service.
Hope this helps! If so, please rate.

Upgrading from cisco LMS 3.0 to a latest version

Hello,
Upgrading from cisco LMS 3.0 to a higher version.
Whatdoes it require?.
What is the current version?
What do we need for upgrading?
Are there specific codes or new need to buy new products?
In case of buying new products, which are the configurations?

H Malik,
You are correct! Latest version is Cisco prime LMS 4.2. There is no direct upgrade from LMS 3.x to LMS 4.x.
The procedure is simple:
Take backup orf old LMS --> Un-install (if same machine)--> Install new LMS --> Restore backup to get old data.
You would need to purchase new license for it.Cisco Prime LMS is now part of the Cisco Prime Infrastructure bundle and is not orderable separately. Cisco Prime Infrastructure bundle follows a size-based incremental licensing model. Device licenses can be combined and added when applied to a single server installation instance. Customers have the option of adding incremental licenses for additional devices as their network grows.Refer to the Cisco Prime Infrastructure Ordering Guide located at http://www.cisco.com/go/primeinfrastructure for the exact part number that matches your requirement and placing the order.
Currently even SmartNet or SAS contracts does not cover major upgrades from LMS 2.x and 3.x; an upgrade part number will need to be purchased to move to Cisco Prime LMS 4.2. These upgrade part numbers reflect a significant discount to protect customers' investment in the Cisco Prime product line.
The data migration process will vary depending on the LMS version from which the data need to be migrated. Migrating data to LMS 4.2:
• LMS 4.2 supports local upgrade or direct inline upgrade only from LMS 4.0.1 and LMS 4.1.
• LMS 4.0 customers are encouraged to install LMS 4.0.1 before doing inline upgrade to LMS 4.2.
• LMS 3.2 and LMS 3.2 Service Pack 1 customers can do a remote upgrade through the LMS backup and restore mechanism.
• LMS 3.1, LMS 3.0, LMS 3.0 December 2007 Update, LMS 2.6, and LMS 2.6 Service Pack 1 customers need to do a remote upgrade to LMS 4.0.1 and then upgrade to LMS 4.2.
-Thanks
Vinod

Cisco 1252 upgrade from standalone autonomous to LWAPP

Similar Messages

Maybe you are looking for