Cisco 1300 configs; ROOT - NON ROOT
I'm using a AIR-BR1310-E-K9-R as ROOT and 5 NON ROOTS type (AIR-BR1310-E-K9).
Im looking for a default config to setup a wireless PTMP link between the ROOT and the NON ROOTS. To make this wireless connection i'm using an AIR-ANT2506
In a point-to-multipoint configuration, two or more non-root bridges associate to a root bridge. Up to 17 non-root bridges can associate to a root bridge, but the non-root bridges must share the available bandwidth See "Configuring the Access Point/Bridge for the First Time," for instructions on initial bridge setup.
http://www.cisco.com/en/US/docs/wireless/access_point/1300/12.2_15_JA/configuration/guide/o13frst.html#wpxref80859
Similar Messages
-
1250 802.11N series in root/non-root bridge mode
Using Yagi's, low loss cable, antenna outside, AP inside.
When operating autonomous 1250 series in root/non-root bridge mode, can I use 802.11N radios? Is it supported?
Or would it be better to use 1242's? This is for a customer, no time for testing, need rock solid design, in and out configuration...@leolaohoo -
I was just asking for a definitive answer, weather its affirmative or negative, is there a benefit to using the 1252 over the 1242 giving the cost of each, since as you said the 802.11N can not be used to bridge, than I would say a 1242 is better fit for the AP bridge of 350', clear line of site over the 1252. -
Cannot Associate 1532 Bridges in Non-Root role
Hello,
Can someone please tell me what I am missing and why I cannot bring up 2 bridges in "Root" and "Non-Root" roles?
I have similarly configured bridges in a Root / Non-Root role several times before with older AP's and never had any issues... although it was always just 1 SSID, 1 Vlan, and no subinterfaces...
The only way I was able to get these 2 bridges to associate was to put the Non-Root bridge into a Workgroup Bridge role and then *BANG* everything worked perfectly. I tried getting rid of the authentication and tried using the Parent command but neither helped. Prior to entering Station Role Workgroup Bridge, the only message I would receive was showing on the Non-Root side and all it said was:
*Mar 1 07:27:13.867 GMT: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response
*Mar 1 07:27:28.891 GMT: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Rcvd response from 544a.0005.8030 channel 3 2815
What am I missing or what have I incorrectly configured on my Non-Root config?
Bridges are both 1532i with the Autonomous Image 15.2(4)JB5
Attached are the configs prior to changing the Non-Root AP to a station role of Workgroup Bridge.
Thanks!Hi,
This should work with multiple sub-interfaces.
Few more suggestions
1. Remove this from your BRIDGE SSID & check
mobility network-id 1
This is only require when you configure L3 roaming & WDS in place.
http://www.cisco.com/c/en/us/support/docs/wireless/aironet-1200-series/8103-ap-faq.html
2. Try to set WPA version 2 & only AES encryption.
Also try to Associate your Bridges using Open Auth first (as shown in my blog post initial section) & then try to add security.
HTH
Rasika
**** Pls rate all useful responses **** -
Autonomous APs' non-root radio tracking Questions
Hi guys,
As you know, we can configure an autonomous AP that is using its .11a radio as "non-root bridge" and its .11b/g as root to track the .11a radio so that if it is down for any reason, then it will shut down the Root Radio. I've some questions about this if someone tested the below scenarios:
(1) If the .11b/g radio has been shut down, will it stay shutdown and never comeback unless an administrator do it manually? Is there an automated feature like the switches 'errdisable recover cause' method?
(2) Is there a command like 'show fallback bla bla ..' that will allow us to see that the current radio state has been shut down due to radio tracking?
B.Regards
MahmoudYes, these model you can configure as Root/Non-Root as long as you have an autonomous image loaded. Most of the time feature is depend on the software code.
Release notes available at below URL for details of the supported/unsupported features of each software version.
http://www.cisco.com/en/US/products/ps12555/prod_release_notes_list.html
Here is one basic config example of Root/Non-Root using different AP model, but it may help you to get basic config done for these AP model as well.
http://mrncciew.com/2013/11/09/wireless-bridge-with-eap-fast/
HTH
Rasika
**** Pls rate all useful responses **** -
Non-root bridge association problem
I have an installation using Cisco 1242 Access Points (IOS) as bridges
in 5Ghz band, and as AP in 2,4 GHz band. Sometimes I get problems
with the non-root bridges, after mains outage, they will not
associate to the root bridge. Command "dot11 do 1 carrier busy"
issued to the non-root bridge helps, but sometimes I have to use it
several times. Have anybody any idea about possible cause?
ThanksHi Frank,
I think I have found the reason of my troubles. It is the following configuration command:
(interface Dot11Radio1)
world-mode dot11d country CZ outdoor
which is not only not-needed on the non-root bridge AP, it prevents associating the non-root bridge to the root-bridge AP. It does not cause the troubles on each root non-root couple. The troubles are more frequent with IOS version 12.3(11)JA or 12.3(8)JEA than with 12.3(8)JA2.
Regards
Frantisek Opravil -
B1400 non-root does not display/monitor temperature
I have root and non-root B1410 bridges. The root bridges will show temperatures in the GUI. The non-root do not. They show a WARNING: No Reading temperature monitoring is at 'INITIALIZE' state. What does this mean? I have not been able to find any reference. Other than root/non-root parms, I see nothing that is different in these configurations. They are in remote locations and temperature reporting is needed.
Thanks for the response. After some digging I found this BUG.
It says fixed in 12.3(8)JA
BUT I CANNOT FIND 12.3(8)JA for the 1400....
BUG ID: CSCsb63034
Bug Details
Headline show env No Reading Temperature monitoring is at INITIALIZE non-root
Product br1410
Feature OTHERS Duplicate of
Severity 3 Severity help Status Verified Status help
First Found-in Version 12.3(4)JA First Fixed-in Version 12.3(8)JA Version help
Release Notes
Symptom:
Non-root bridge running 12.3.4.JA & greater 'show env' output sometimes shows:
Environmental Statistics
Environmental status as of 09:47:18 S Aug 8 2005
Data is 55 second(s) old, refresh in 5 second(s)
WARNING: No Reading temperature monitoring is at 'INITIALIZE' state.
No Reading temperature is at 0 (C)
Workaround:
None but this appears to be cosmetic.
-pat -
Cisco Aironet 1250 - How to bridge two AP's and get Non-root to talk to Root AP
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin-top:0in;
mso-para-margin-right:0in;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0in;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:Arial;
mso-bidi-theme-font:minor-bidi;}
I have two buidlings acroos the street from each other. I have two Cisco Aironet 1250 wireless AP's with the first one going in the main building with network backbone. The Second AP goes across the street with the other wired network segment. Both AP's have long range antenas 2.4 GHZ on top of each building. I have configured the 1st one as the Root Bridge. The one across the street is configured as non-root bridge. I have both AP's configured with the same WEP key and also with the same SSID name with both set to broadcast it. I am still unsure and confused as to how I get the non-root bridge to talk to and use the root bridge to get on the main network.
1- It’s main to use the Root parent Mac address.
2- Is there another config that I am missing to get the signal?
Note: I still not getting any signal from the root although distance between root and non-root is 330m
My root antenna is AIR-ANT24120 and non-root antenna is AIR-ANT1949 and attached files is my configuration files
Thank you.1. How are the AIR-ANT24120 and the AIR-ANT1949 installed?
the AIR-ANT24120 is connected virtically on tower far 11m from the earth and AIR-ANT1949 is connected horizontally on tower far 10m from the earth
2. What is the distance between both APs?
350 m
3. Do you have clear line-of-sight between the two?
there is one tanker in the middle between them but it's far 7m from the earth
4. Is the two APs properly aligned?
i think yes and changed the aligned many times without any news (I don't have any tools for alignment)
5. Which point are the antennas connected to? Primary, Secondary or middle?
I tried in the primary and secondary but never tried the middle antenna
Thanks -
Cannot associate between non-root to root on 1300 Bridge
I installed 4 1300 Bridges, point to multipoint configuration. One bridges is acting as root whereas the other 3 are non-root. The SSID are locked down manually. None of these non-root can associate to the root, I noticed that the wireless interface is (hardware/software) are down eventhough I enabledit. When I changed the non-root to become root, the wireless interface went up. This doesn't make sense. Pls help. Thanks.
I'm sure you have checked the required parameters needed to connect your non-root bridges, i.e. distance is set for the root, pwr settings, no encryption set for now. I've seen this issue as well on the 1310 with no solution from Cisco. It works well in a PP link. Try to establish the PP link between one bridge first. Leave the SSID as tsunami and broadcast it. Make sure you can associate with one of the non-root when you set it up for client association. I'm sure the radio is fine, but this can verify that.
-
1300 Root-Bridge and Non-Root Bridge setup
I have two 1300s that I am trying to set up as Root Bridge and Non-Root Bridge, however, everytime i specify one of them as a Non-Root bridge, the radio0 interface becomes disabled. The only option that i am able to pick that enables the radio0 interface is "Access Point", which is what am trying to avoid it being.
Can anybody help me figure out how to go about thisA non-root's radio will show as disabled if it cannot find the root AP to associate to. Make sure you have "infrastructure-ssid" configured under the SSID on both the root and non-root bridges. Also depending on code versions you may have to configure the distance command under the radio interface on the root.
-
Non-root is not associate with root
I am working to setup the non-root associate with root. I have checked every configuration from the root are the same as non-root. Accept it set to non-root.
- It is the same VLAN, SSID, authentication is open. I have encryption from both sides are the same.
It is still not associated. What else should I check from the non-root to get association? Please give me some helps
I am really appreciated that.
The root configuration:
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname Root_Bridge
no logging console
aaa new-model
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login default local
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
resource policy
clock timezone MST -7
clock save interval 24
ip subnet-zero
ip domain name Bridge
ip ssh time-out 60
ip ssh version 2
no dot11 igmp snooping-helper
dot11 vlan-name Management vlan 51
dot11 vlan-name User vlan 11
dot11 ssid LOCALBRIDGE
vlan 51
authentication open
infrastructure-ssid
dot11 network-map
crypto pki trustpoint TP-self-signed-4076113752
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-4076113752
revocation-check none
rsakeypair TP-self-signed-4076113752
crypto pki certificate chain TP-self-signed-4076113752
certificate self-signed 01
30820261 308201CA A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 34303736 31313337 3532301E 170D3032 30333031 30303030
33345A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D34 30373631
31333735 3230819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100B329 87F691CA 1107EC3A 9EF4676D 2F96A7E4 42DBB88F 426D78C1 0E9E09A0
8F5EA9A1 DF88C33A A0DF128A E13E6E59 E9232487 0F5C953C 274DF314 1F48544F
E213D232 85B1E45A 4D186A9E FF9581E6 3E471891 16B627B6 CB3D8F01 BCFF89E0
77E8EA44 0E255F75 BFF1299A B3198E9B 61B3056B 8F365D98 2A8D463E F3122C47
B80D0203 010001A3 81883081 85300F06 03551D13 0101FF04 05300301 01FF3032
0603551D 11042B30 29822737 3332385F 42726964 67652E64 61766973 2D6D6F6E
7468616E 2E616363 2E64732E 61662E6D 696C301F 0603551D 23041830 1680145F
9DB7F2A6 BD563ACB 429F6938 6AF9D336 69139F30 1D060355 1D0E0416 04145F9D
B7F2A6BD 563ACB42 9F69386A F9D33669 139F300D 06092A86 4886F70D 01010405
00038181 00372387 521D029A FAE2F579 73EDCF3B FDF262EE 5DF6154E 5469A5BD
6630E5FD C8A1311A A24493D4 D1856862 8979692B CDFE65D7 29E97B60 FCC37584
A27FA332 9CC5F175 2EDC871C D41BA4F5 A50634DE 75210305 47240D4F A30D0046
532F68ED 569CE374 98C5F53D A417CFBF 3A93C98A D399B06E A73E61AB D4889452
0B695B54 86
quit
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption key 1 size 128bit 7 E99521751C16125A7754722A6B72 transmit-key
encryption key 2 size 128bit 7 1857F02303182327EA1A9242A53B
encryption key 3 size 128bit 7 FE1CF103855EBB2763224F129556
encryption key 4 size 128bit 7 19A03A5D596B029A01C208EF1C0F
encryption mode ciphers wep128
encryption vlan 11 key 1 size 128bit 7 419258EC0B7E6C7413C571760B67 transmit-key
encryption vlan 11 key 2 size 128bit 7 AB3C5B091B37223F39306B1F7442
encryption vlan 11 key 3 size 128bit 7 3E1CF103855EBB2763224F129556
encryption vlan 11 key 4 size 128bit 7 E858C5382B5D5E372A6C0438604C
encryption vlan 11 mode wep mandatory
encryption vlan 51 key 1 size 128bit 7 90792B34ACD2C8D18A0B7AF3AC68 transmit-key
encryption vlan 51 key 2 size 128bit 7 72063EA2FEF03A39E5468E92A7C5
encryption vlan 51 key 3 size 128bit 7 8607AEADB49EE0B7E4529770D9AE
encryption vlan 51 key 4 size 128bit 7 F60210B48CB39887A59255187D6D
encryption vlan 51 mode wep mandatory
ssid LOCALBRIDGE
speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
packet retries 128
station-role root
rts threshold 4000
rts retries 128
cca 87
concatenation
distance 5
beacon period 20
infrastructure-client
interface Dot11Radio0.11
encapsulation dot1Q 11
no ip route-cache
no snmp trap link-status
bridge-group 11
interface Dot11Radio0.51
encapsulation dot1Q 51 native
no ip route-cache
no snmp trap link-status
bridge-group 1
interface FastEthernet0
no ip address
no ip route-cache
hold-queue 80 in
interface FastEthernet0.11
encapsulation dot1Q 11
no ip route-cache
no snmp trap link-status
bridge-group 11
interface FastEthernet0.51
encapsulation dot1Q 51 native
no ip route-cache
no snmp trap link-status
bridge-group 1
interface BVI1
ip address 192.168.0.5 255.255.255.0
no ip route-cache
no ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
logging history informational
snmp-server view dot11view ieee802dot11 included
snmp-server community PUBLICSTRING RW
snmp-server chassis-id Bridge
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps entity
snmp-server enable traps disassociate
snmp-server enable traps deauthenticate
snmp-server enable traps authenticate-fail
snmp-server enable traps dot11-qos
snmp-server enable traps wlan-wep
snmp-server enable traps config
snmp-server enable traps syslog
snmp-server enable traps cpu threshold
snmp-server enable traps aaa_server
snmp-server enable traps envmon
snmp-server host 192.168.9.10 PUBLICSTRING
tacacs-server host 192.168.6.100
tacacs-server host 192.168.4.100
tacacs-server directed-request
radius-server attribute 32 include-in-access-req format %h
radius-server vsa send accounting
bridge 1 protocol ieee
bridge 1 route ip
line con 0
access-class 111 in
line vty 0 4
access-class 111 in
line vty 5 15
access-class 111 in
end
The non-root configuration:
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname Bridge
logging console informational
logging monitor informational
aaa new-model
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login default local
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa cache profile admin_cache
all
aaa session-id common
resource policy
clock timezone MST -7
clock save interval 24
ip subnet-zero
ip domain name Bridge
no dot11 igmp snooping-helper
dot11 activity-timeout bridge default 3600
dot11 vlan-name Management vlan 51
dot11 vlan-name User vlan 11
dot11 ssid LOCALBRIDGE
vlan 51
authentication open
infrastructure-ssid
dot11 network-map
no crypto provisioning petitioner
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption key 1 size 128bit 7 E99521751C16125A7754722A6B72 transmit-key
encryption key 2 size 128bit 7 1857F02303182327EA1A9242A53B
encryption key 3 size 128bit 7 FE1CF103855EBB2763224F129556
encryption key 4 size 128bit 7 19A03A5D596B029A01C208EF1C0F
encryption mode ciphers wep128
encryption vlan 11 key 1 size 128bit 7 419258EC0B7E6C7413C571760B67 transmit-key
encryption vlan 11 key 2 size 128bit 7 AB3C5B091B37223F39306B1F7442
encryption vlan 11 key 3 size 128bit 7 3E1CF103855EBB2763224F129556
encryption vlan 11 key 4 size 128bit 7 E858C5382B5D5E372A6C0438604C
encryption vlan 11 mode wep mandatory
encryption vlan 51 key 1 size 128bit 7 90792B34ACD2C8D18A0B7AF3AC68 transmit-key
encryption vlan 51 key 2 size 128bit 7 72063EA2FEF03A39E5468E92A7C5
encryption vlan 51 key 3 size 128bit 7 8607AEADB49EE0B7E4529770D9AE
encryption vlan 51 key 4 size 128bit 7 F60210B48CB39887A59255187D6D
encryption vlan 51 mode wep mandatory
ssid LOCALBRIDGE
speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
packet retries 128
station-role non-root bridge
rts threshold 4000
rts retries 128
cca 87
concatenation
beacon period 20
infrastructure-client
interface Dot11Radio0.11
encapsulation dot1Q 11
no ip route-cache
no snmp trap link-status
bridge-group 11
interface Dot11Radio0.51
encapsulation dot1Q 51 native
no ip route-cache
no snmp trap link-status
bridge-group 1
interface FastEthernet0
no ip address
no ip route-cache
hold-queue 80 in
interface FastEthernet0.11
encapsulation dot1Q 11
no ip route-cache
no snmp trap link-status
bridge-group 11
interface FastEthernet0.51
encapsulation dot1Q 51 native
no ip route-cache
no snmp trap link-status
bridge-group 1
interface BVI1
ip address 192.168.0.10 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
snmp-server community PUBLICSTRING RW
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps entity
snmp-server enable traps disassociate
snmp-server enable traps deauthenticate
snmp-server enable traps authenticate-fail
snmp-server enable traps dot11-qos
snmp-server enable traps wlan-wep
snmp-server enable traps config
snmp-server enable traps syslog
snmp-server enable traps cpu threshold
snmp-server enable traps aaa_server
snmp-server enable traps envmon
snmp-server host 192.168.9.10 PUBLICSTRING
tacacs-server host 192.168.6.100
tacacs-server host 192.168.4.100
tacacs-server directed-request
radius-server attribute 32 include-in-access-req format %h
radius-server vsa send accounting
bridge 1 protocol ieee
bridge 1 route ip
bridge 11 protocol ieee
line con 0
line vty 0 4
endwhat happens if you go completely open, no WEP?
and I wouldn't use WEP, it's very breakable.
Steve -
NON-ROOT TO NON-ROOT ASSOCIATION??
Hi,
I have one AIR-AP1242AG-A-K9, and two AIR-AP1242AG-N-K9. I have already configure them to work as bridge.
Root Bridge with wireless-clients -----------> 1 AIR-AP1242AG-N-K9
Non-Root Bridge1 with wireless-clients ---> 1 AIR-AP1242AG-N-K9
Non-Root Bridge2 with wireless-clients ----> 1 AIR-AP1242AG-A-K9
I notice after reseting the root bridge or one of the non-root bridges that when I type the command "sh DOt11 associations" the results shows that there is an associatiation between the 2 Non-Root bridge. When this happend the connection of the clients associated to this APs is very unstable.
as far as I know the association is just between Root and Non-Root bridges.
I don´t know why this happend.
In order to avoid this I disable in one of the non-root bridge (AIR-AP1242AG-A-K9) the option "Force Infrastructure Device to associate only...."
Cisco's Docs show an example of config when there is one root bridge and one non-root bridge but in my scenario I have 2 non-root bridge and one root bridge.
I would like to know if the config for my scenario must be different from the simple scenario (1 root and 1 non-root).
I hope any of you can help me.
RegardsHi Scott,
Thanks for your recommendations.
The mac-address authentication option you recommend is the option shown as "Root Parent MAC 1" ,"Root Parent MAC 2 ....." on Setting---> Network interface???
For root bridge , I should write down the MAC addres of the non-root bridge1 on Root Parent MAC 1 field and on the field of Root Parent MAC 2, the MAC of the non-root bridge2 ?? , am I right?
and for the non-root bridges I should just set on Root Parent MAC 1 just the MAC address of the root bridge???
Regards, -
Wireless Root Bridge - Non Root Bridge
I've been reading a lot about bridge configuration for wireless AP but i cannot make it work the following scenario:
PC -- ethernet port --> Non-Root-Bridge -----------> Root Bridge ---------> Switch
vlan111 native 18 - vlan111 native 18 - vlan111 vlan native 18,111
Its pinging fine between switch and Non-Root. But when i put vlan111 on Non-Root the two AP's stop responding to the network.
What am i doing wrong? Plz i need some help!! I have two 1242.
------------------------ Root Config ----------------------
dot11 syslog
dot11 vlan-name JGS111 vlan 111
dot11 vlan-name JGS18 vlan 18
dot11 ssid WGB
vlan 18
authentication open
guest-mode
infrastructure-ssid
username Cisco password 7 047802150C2E
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid WGB
station-role root bridge
infrastructure-client
interface Dot11Radio0.18
encapsulation dot1Q 18 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface Dot11Radio0.111
encapsulation dot1Q 111
no ip route-cache
bridge-group 111
bridge-group 111 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface FastEthernet0.18
encapsulation dot1Q 18 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0.111
encapsulation dot1Q 111
no ip route-cache
bridge-group 111
bridge-group 111 spanning-disabled
interface BVI1
ip address 10.1.8.50 255.255.255.0
no ip route-cache
ip default-gateway 10.1.8.254
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
------------- Non-Root-Bridge -------------
ot11 syslog
dot11 vlan-name JGS111 vlan 111
dot11 vlan-name JGS18 vlan 18
dot11 ssid WGB
vlan 18
authentication open
guest-mode
infrastructure-ssid
username Cisco password 7 14341B180F0B
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid WGB
station-role non-root bridge
infrastructure-client
interface Dot11Radio0.18
encapsulation dot1Q 18 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface Dot11Radio0.111
encapsulation dot1Q 111
no ip route-cache
bridge-group 111
bridge-group 111 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface FastEthernet0.18
encapsulation dot1Q 18 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0.111
encapsulation dot1Q 111
no ip route-cache
bridge-group 111
bridge-group 111 spanning-disabled
interface BVI1
ip address 10.1.8.51 255.255.255.0
no ip route-cache
ip default-gateway 10.1.8.254
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ipTry this:
interface Dot11Radio0.18
encapsulation dot1Q 18 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.111
encapsulation dot1Q 111
no ip route-cache
bridge-group 111
bridge-group 111 subscriber-loop-control
bridge-group 111 block-unknown-source
no bridge-group 111 source-learning
no bridge-group 111 unicast-flooding
bridge-group 111 spanning-disabled
interface FastEthernet0.18
encapsulation dot1Q 10 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.111
encapsulation dot1Q 111
no ip route-cache
bridge-group 111
no bridge-group 111 source-learning
bridge-group 111 spanning-disabled
Make sure your switchort is setup similar
interface GigabitEthernet0/7
description 1242 AP Bridge
switchport trunk encapsulation dot1q
switchport trunk native vlan 18
switchport trunk allowed vlans 18,111
switchport mode trunk
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
Changing native VLAN on non-root bridges
I have quite a few 1310 Bridges setup in point to multipoint configuration with a root bridge with a sector antenna at the campus network and remote sites connecting in. I have multiple VLANs trunked onto one SSID, this allows for having multiple vlans in use at the remote site. The problem is I want to configure some remote site bridges with a different native vlan than the standard allowing me to plug the client directly into the injector and eliminate the need for a vlan aware switch. I have tried to configure the the "encapsulation dot1q VLAN# native" but this swaps the bridge group on the subinterface to a bridge-group 1 .
! Last configuration change at 01:23:08 UTC Tue Sep 15 2009 by Cisco
! NVRAM config last updated at 01:23:09 UTC Tue Sep 15 2009 by Cisco
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
no aaa new-model
dot11 ssid Cisco-24
vlan 1
authentication open
authentication key-management wpa
guest-mode
infrastructure-ssid optional
wpa-psk ascii test
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm tkip
encryption vlan 1 mode ciphers aes-ccm tkip
encryption vlan 901 mode ciphers aes-ccm tkip
encryption vlan 902 mode ciphers aes-ccm tkip
encryption vlan 904 mode ciphers aes-ccm tkip
ssid Cisco-24
speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0
station-role non-root bridge
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface Dot11Radio0.901
encapsulation dot1Q 901
no ip route-cache
bridge-group 255
bridge-group 255 spanning-disabled
interface Dot11Radio0.902
encapsulation dot1Q 902
no ip route-cache
bridge-group 254
bridge-group 254 spanning-disabled
interface Dot11Radio0.904
encapsulation dot1Q 904
no ip route-cache
bridge-group 253
bridge-group 253 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
hold-queue 80 in
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
interface FastEthernet0.901
encapsulation dot1Q 901
no ip route-cache
bridge-group 255
bridge-group 255 spanning-disabled
interface FastEthernet0.902
encapsulation dot1Q 902
no ip route-cache
bridge-group 254
bridge-group 254 spanning-disabled
interface FastEthernet0.904
encapsulation dot1Q 904
no ip route-cache
bridge-group 253
bridge-group 253 spanning-disabled
interface BVI1
ip address 10.0.0.100 255.255.255.0
no ip route-cache
ip default-gateway 10.0.0.1
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
snmp-server community misdept RO
bridge 1 route ip
line con 0
line vty 0 4
login local
endCorrect. As soon as you change it to 100, you will lose access to the devices since vlan 1 is used for management. To shorten the down time, you can create vlan 100 and all the SVIs on all switches ahead of time and than change it form 1 to 100 in a maintenance window.
HTH -
[SOLVED] Xorg not starting on non-root user [My First Linux]
Hello, I recently turned back to linux after digging up my old ASUS EEE 900a, which I messed up with partitioning fun after trying to cram Windows XP on it and etc. Anyways, I managed to fix it, and after Ubuntu being too big, I was turned on to Arch as a good distro, and I've been having a very good time setting everything up so far.
Anyways: My issue arises after needing to use a different user in order to use Chrome. I created a new account and tried to run startx like I usually do. It spat out the usual few lines, but failed and gave me this log:
[ 4616.974]
X.Org X Server 1.14.1
Release Date: 2013-04-17
[ 4616.974] X Protocol Version 11, Revision 0
[ 4616.974] Build Operating System: Linux 3.8.7-1-ARCH i686
[ 4616.974] Current Operating System: Linux archieee 3.9.4-1-ARCH #1 SMP PREEMPT Sun May 26 11:56:48 CEST 2013 i686
[ 4616.975] Kernel command line: root=/dev/sda1 ro initrd=../initramfs-linux.img BOOT_IMAGE=../vmlinuz-linux
[ 4616.975] Build Date: 17 April 2013 02:43:06PM
[ 4616.975]
[ 4616.975] Current version of pixman: 0.30.0
[ 4616.975] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 4616.975] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 4616.977] (==) Log file: "/var/log/Xorg.0.log", Time: Tue Jun 4 21:56:02 2013
[ 4616.977] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 4616.978] (==) No Layout section. Using the first Screen section.
[ 4616.978] (==) No screen section available. Using defaults.
[ 4616.978] (**) |-->Screen "Default Screen Section" (0)
[ 4616.978] (**) | |-->Monitor "<default monitor>"
[ 4616.978] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 4616.978] (==) Automatically adding devices
[ 4616.978] (==) Automatically enabling devices
[ 4616.978] (==) Automatically adding GPU devices
[ 4616.978] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 4616.978] Entry deleted from font path.
[ 4616.978] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 4616.978] Entry deleted from font path.
[ 4616.978] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 4616.978] Entry deleted from font path.
[ 4616.978] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 4616.979] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 4616.979] Entry deleted from font path.
[ 4616.979] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 4616.979] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/
[ 4616.979] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 4616.979] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 4616.979] (II) Loader magic: 0x8258620
[ 4616.979] (II) Module ABI versions:
[ 4616.979] X.Org ANSI C Emulation: 0.4
[ 4616.979] X.Org Video Driver: 14.1
[ 4616.979] X.Org XInput driver : 19.1
[ 4616.979] X.Org Server Extension : 7.0
[ 4616.980] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 4616.983] (--) PCI:*(0:0:2:0) 8086:27ae:1043:8340 rev 3, Mem @ 0xf3e00000/524288, 0xd0000000/268435456, 0xf3dc0000/262144, I/O @ 0x0000cc00/8
[ 4616.983] (--) PCI: (0:0:2:1) 8086:27a6:1043:8340 rev 3, Mem @ 0xf3e80000/524288
[ 4616.983] Initializing built-in extension Generic Event Extension
[ 4616.983] Initializing built-in extension SHAPE
[ 4616.984] Initializing built-in extension MIT-SHM
[ 4616.984] Initializing built-in extension XInputExtension
[ 4616.984] Initializing built-in extension XTEST
[ 4616.984] Initializing built-in extension BIG-REQUESTS
[ 4616.984] Initializing built-in extension SYNC
[ 4616.984] Initializing built-in extension XKEYBOARD
[ 4616.984] Initializing built-in extension XC-MISC
[ 4616.985] Initializing built-in extension SECURITY
[ 4616.985] Initializing built-in extension XINERAMA
[ 4616.987] Initializing built-in extension XFIXES
[ 4616.990] Initializing built-in extension RENDER
[ 4616.993] Initializing built-in extension RANDR
[ 4616.995] Initializing built-in extension COMPOSITE
[ 4616.998] Initializing built-in extension DAMAGE
[ 4617.000] Initializing built-in extension MIT-SCREEN-SAVER
[ 4617.003] Initializing built-in extension DOUBLE-BUFFER
[ 4617.005] Initializing built-in extension RECORD
[ 4617.007] Initializing built-in extension DPMS
[ 4617.010] Initializing built-in extension X-Resource
[ 4617.012] Initializing built-in extension XVideo
[ 4617.015] Initializing built-in extension XVideo-MotionCompensation
[ 4617.017] Initializing built-in extension XFree86-VidModeExtension
[ 4617.019] Initializing built-in extension XFree86-DGA
[ 4617.021] Initializing built-in extension XFree86-DRI
[ 4617.023] Initializing built-in extension DRI2
[ 4617.023] (II) LoadModule: "glx"
[ 4617.024] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 4617.024] (II) Module glx: vendor="X.Org Foundation"
[ 4617.024] compiled for 1.14.1, module version = 1.0.0
[ 4617.024] ABI class: X.Org Server Extension, version 7.0
[ 4617.024] (==) AIGLX enabled
[ 4617.026] Loading extension GLX
[ 4617.026] (==) Matched intel as autoconfigured driver 0
[ 4617.026] (==) Matched intel as autoconfigured driver 1
[ 4617.026] (==) Matched vesa as autoconfigured driver 2
[ 4617.026] (==) Matched modesetting as autoconfigured driver 3
[ 4617.026] (==) Matched fbdev as autoconfigured driver 4
[ 4617.026] (==) Assigned the driver to the xf86ConfigLayout
[ 4617.026] (II) LoadModule: "intel"
[ 4617.026] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 4617.027] (II) Module intel: vendor="X.Org Foundation"
[ 4617.027] compiled for 1.14.1, module version = 2.21.8
[ 4617.027] Module class: X.Org Video Driver
[ 4617.027] ABI class: X.Org Video Driver, version 14.1
[ 4617.027] (II) LoadModule: "vesa"
[ 4617.027] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
[ 4617.028] (II) Module vesa: vendor="X.Org Foundation"
[ 4617.028] compiled for 1.14.0, module version = 2.3.2
[ 4617.028] Module class: X.Org Video Driver
[ 4617.028] ABI class: X.Org Video Driver, version 14.1
[ 4617.028] (II) LoadModule: "modesetting"
[ 4617.029] (WW) Warning, couldn't open module modesetting
[ 4617.029] (II) UnloadModule: "modesetting"
[ 4617.029] (II) Unloading modesetting
[ 4617.029] (EE) Failed to load module "modesetting" (module does not exist, 0)
[ 4617.029] (II) LoadModule: "fbdev"
[ 4617.029] (WW) Warning, couldn't open module fbdev
[ 4617.029] (II) UnloadModule: "fbdev"
[ 4617.030] (II) Unloading fbdev
[ 4617.030] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 4617.030] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),
Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),
Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),
Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),
Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server,
Ivybridge Server (GT2), Haswell Desktop (GT1), Haswell Desktop (GT2),
Haswell Desktop (GT3), Haswell Mobile (GT1), Haswell Mobile (GT2),
Haswell Mobile (GT3), Haswell Server (GT1), Haswell Server (GT2),
Haswell Server (GT3), Haswell (GT1), Haswell (GT2), Haswell (GT3),
Haswell (GT1), Haswell (GT2), Haswell (GT3),
Haswell SDV Desktop (GT1), Haswell SDV Desktop (GT2),
Haswell SDV Desktop (GT3), Haswell SDV Mobile (GT1),
Haswell SDV Mobile (GT2), Haswell SDV Mobile (GT3),
Haswell SDV Server (GT1), Haswell SDV Server (GT2),
Haswell SDV Server (GT3), Haswell SDV (GT1), Haswell SDV (GT2),
Haswell SDV (GT3), Haswell SDV (GT1), Haswell SDV (GT2),
Haswell SDV (GT3), Haswell ULT Desktop (GT1),
Haswell ULT Desktop (GT2), Haswell ULT Desktop (GT3),
Haswell ULT Mobile (GT1), Haswell ULT Mobile (GT2),
Haswell ULT Mobile (GT3), Haswell ULT Server (GT1),
Haswell ULT Server (GT2), Haswell ULT Server (GT3),
Haswell ULT (GT1), Haswell ULT (GT2), Haswell ULT (GT3),
Haswell ULT (GT1), Haswell ULT (GT2), Haswell ULT (GT3),
Haswell CRW Desktop (GT1), Haswell CRW Desktop (GT2),
Haswell CRW Desktop (GT3), Haswell CRW Mobile (GT1),
Haswell CRW Mobile (GT2), Haswell CRW Mobile (GT3),
Haswell CRW Server (GT1), Haswell CRW Server (GT2),
Haswell CRW Server (GT3), Haswell CRW (GT1), Haswell CRW (GT2),
Haswell CRW (GT3), Haswell CRW (GT1), Haswell CRW (GT2),
Haswell CRW (GT3), ValleyView PO board
[ 4617.032] (II) VESA: driver for VESA chipsets: vesa
[ 4617.032] (++) using VT number 1
[ 4617.033] (WW) Falling back to old probe method for vesa
[ 4617.033] (II) intel(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 4617.034] (==) intel(0): Depth 24, (--) framebuffer bpp 32
[ 4617.034] (==) intel(0): RGB weight 888
[ 4617.034] (==) intel(0): Default visual is TrueColor
[ 4617.034] (--) intel(0): Integrated Graphics Chipset: Intel(R) 945GME
[ 4617.034] (**) intel(0): Relaxed fencing disabled
[ 4617.034] (**) intel(0): Wait on SwapBuffers? enabled
[ 4617.034] (**) intel(0): Triple buffering? enabled
[ 4617.034] (**) intel(0): Framebuffer tiled
[ 4617.034] (**) intel(0): Pixmaps tiled
[ 4617.034] (**) intel(0): 3D buffers tiled
[ 4617.034] (**) intel(0): SwapBuffers wait enabled
[ 4617.034] (==) intel(0): video overlay key set to 0x101fe
[ 4617.034] (II) intel(0): Output LVDS1 has no monitor section
[ 4617.035] (--) intel(0): found backlight control interface /sys/class/backlight/eeepc
[ 4617.066] (II) intel(0): Output VGA1 has no monitor section
[ 4617.067] (II) intel(0): EDID for output LVDS1
[ 4617.067] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 4617.067] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 4617.067] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 4617.068] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 4617.068] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 4617.068] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 4617.068] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 4617.068] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 4617.068] (II) intel(0): Printing probed modes for output LVDS1
[ 4617.068] (II) intel(0): Modeline "1024x600"x60.0 45.00 1024 1077 1112 1200 600 604 609 625 -hsync -vsync (37.5 kHz P)
[ 4617.068] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz d)
[ 4617.068] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz d)
[ 4617.068] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz d)
[ 4617.100] (II) intel(0): EDID for output VGA1
[ 4617.100] (II) intel(0): Output LVDS1 connected
[ 4617.100] (II) intel(0): Output VGA1 disconnected
[ 4617.100] (II) intel(0): Using exact sizes for initial modes
[ 4617.100] (II) intel(0): Output LVDS1 using initial mode 1024x600
[ 4617.100] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 4617.100] (II) intel(0): Kernel page flipping support detected, enabling
[ 4617.100] (==) intel(0): DPI set to (96, 96)
[ 4617.100] (II) Loading sub module "fb"
[ 4617.100] (II) LoadModule: "fb"
[ 4617.101] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 4617.102] (II) Module fb: vendor="X.Org Foundation"
[ 4617.103] compiled for 1.14.1, module version = 1.0.0
[ 4617.103] ABI class: X.Org ANSI C Emulation, version 0.4
[ 4617.103] (II) Loading sub module "dri2"
[ 4617.103] (II) LoadModule: "dri2"
[ 4617.103] (II) Module "dri2" already built-in
[ 4617.103] (II) UnloadModule: "vesa"
[ 4617.103] (II) Unloading vesa
[ 4617.103] (==) Depth 24 pixmap format is 32 bpp
[ 4617.104] (II) intel(0): [DRI2] Setup complete
[ 4617.104] (II) intel(0): [DRI2] DRI driver: i915
[ 4617.104] (II) intel(0): Allocated new frame buffer 1024x600 stride 4096, tiled
[ 4617.104] (II) UXA(0): Driver registered support for the following operations:
[ 4617.104] (II) solid
[ 4617.104] (II) copy
[ 4617.104] (II) composite (RENDER acceleration)
[ 4617.104] (II) put_image
[ 4617.105] (II) get_image
[ 4617.105] (==) intel(0): Backing store disabled
[ 4617.105] (==) intel(0): Silken mouse enabled
[ 4617.105] (II) intel(0): Initializing HW Cursor
[ 4617.105] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 4617.113] (==) intel(0): DPMS enabled
[ 4617.113] (==) intel(0): Intel XvMC decoder disabled
[ 4617.113] (II) intel(0): Set up textured video
[ 4617.113] (II) intel(0): Set up overlay video
[ 4617.113] (II) intel(0): direct rendering: DRI2 Enabled
[ 4617.113] (==) intel(0): hotplug detection: "enabled"
[ 4617.123] (--) RandR disabled
[ 4617.160] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 4617.160] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 4617.160] (II) AIGLX: enabled GLX_ARB_create_context
[ 4617.160] (II) AIGLX: enabled GLX_ARB_create_context_profile
[ 4617.160] (II) AIGLX: enabled GLX_EXT_create_context_es2_profile
[ 4617.160] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 4617.160] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 4617.160] (II) AIGLX: Loaded and initialized i915
[ 4617.160] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 4617.162] (II) intel(0): Setting screen physical size to 270 x 158
[ 4617.278] (II) config/udev: Adding input device Power Button (/dev/input/event4)
[ 4617.278] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 4617.278] (II) LoadModule: "evdev"
[ 4617.278] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 4617.279] (II) Module evdev: vendor="X.Org Foundation"
[ 4617.279] compiled for 1.14.0, module version = 2.8.0
[ 4617.279] Module class: X.Org XInput Driver
[ 4617.279] ABI class: X.Org XInput driver, version 19.1
[ 4617.279] (II) Using input driver 'evdev' for 'Power Button'
[ 4617.279] (**) Power Button: always reports core events
[ 4617.279] (**) evdev: Power Button: Device: "/dev/input/event4"
[ 4617.279] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 4617.279] (--) evdev: Power Button: Found keys
[ 4617.279] (II) evdev: Power Button: Configuring as keyboard
[ 4617.279] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4/event4"
[ 4617.279] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 4617.279] (**) Option "xkb_rules" "evdev"
[ 4617.280] (**) Option "xkb_model" "evdev"
[ 4617.280] (**) Option "xkb_layout" "us"
[ 4617.363] (II) config/udev: Adding input device Video Bus (/dev/input/event7)
[ 4617.363] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 4617.363] (II) Using input driver 'evdev' for 'Video Bus'
[ 4617.363] (**) Video Bus: always reports core events
[ 4617.363] (**) evdev: Video Bus: Device: "/dev/input/event7"
[ 4617.363] (--) evdev: Video Bus: Vendor 0 Product 0x6
[ 4617.364] (--) evdev: Video Bus: Found keys
[ 4617.364] (II) evdev: Video Bus: Configuring as keyboard
[ 4617.364] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7/event7"
[ 4617.364] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 4617.364] (**) Option "xkb_rules" "evdev"
[ 4617.364] (**) Option "xkb_model" "evdev"
[ 4617.364] (**) Option "xkb_layout" "us"
[ 4617.365] (II) config/udev: Adding input device Power Button (/dev/input/event3)
[ 4617.365] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 4617.365] (II) Using input driver 'evdev' for 'Power Button'
[ 4617.366] (**) Power Button: always reports core events
[ 4617.366] (**) evdev: Power Button: Device: "/dev/input/event3"
[ 4617.366] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 4617.366] (--) evdev: Power Button: Found keys
[ 4617.366] (II) evdev: Power Button: Configuring as keyboard
[ 4617.366] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3/event3"
[ 4617.366] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[ 4617.366] (**) Option "xkb_rules" "evdev"
[ 4617.366] (**) Option "xkb_model" "evdev"
[ 4617.366] (**) Option "xkb_layout" "us"
[ 4617.368] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)
[ 4617.368] (II) No input driver specified, ignoring this device.
[ 4617.368] (II) This device may have been added with another device file.
[ 4617.369] (II) config/udev: Adding input device Sleep Button (/dev/input/event2)
[ 4617.369] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[ 4617.369] (II) Using input driver 'evdev' for 'Sleep Button'
[ 4617.369] (**) Sleep Button: always reports core events
[ 4617.369] (**) evdev: Sleep Button: Device: "/dev/input/event2"
[ 4617.369] (--) evdev: Sleep Button: Vendor 0 Product 0x3
[ 4617.369] (--) evdev: Sleep Button: Found keys
[ 4617.369] (II) evdev: Sleep Button: Configuring as keyboard
[ 4617.369] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2/event2"
[ 4617.369] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[ 4617.369] (**) Option "xkb_rules" "evdev"
[ 4617.369] (**) Option "xkb_model" "evdev"
[ 4617.369] (**) Option "xkb_layout" "us"
[ 4617.370] (II) config/udev: Adding drm device (/dev/dri/card0)
[ 4617.371] (II) config/udev: Adding input device HDA Intel Mic (/dev/input/event8)
[ 4617.372] (II) No input driver specified, ignoring this device.
[ 4617.372] (II) This device may have been added with another device file.
[ 4617.372] (II) config/udev: Adding input device HDA Intel Headphone (/dev/input/event9)
[ 4617.372] (II) No input driver specified, ignoring this device.
[ 4617.372] (II) This device may have been added with another device file.
[ 4617.373] (II) config/udev: Adding input device Asus EeePC extra buttons (/dev/input/event5)
[ 4617.373] (**) Asus EeePC extra buttons: Applying InputClass "evdev keyboard catchall"
[ 4617.373] (II) Using input driver 'evdev' for 'Asus EeePC extra buttons'
[ 4617.373] (**) Asus EeePC extra buttons: always reports core events
[ 4617.373] (**) evdev: Asus EeePC extra buttons: Device: "/dev/input/event5"
[ 4617.374] (--) evdev: Asus EeePC extra buttons: Vendor 0 Product 0
[ 4617.374] (--) evdev: Asus EeePC extra buttons: Found keys
[ 4617.374] (II) evdev: Asus EeePC extra buttons: Configuring as keyboard
[ 4617.374] (**) Option "config_info" "udev:/sys/devices/platform/eeepc/input/input5/event5"
[ 4617.374] (II) XINPUT: Adding extended input device "Asus EeePC extra buttons" (type: KEYBOARD, id 10)
[ 4617.374] (**) Option "xkb_rules" "evdev"
[ 4617.374] (**) Option "xkb_model" "evdev"
[ 4617.374] (**) Option "xkb_layout" "us"
[ 4617.375] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 4617.375] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 4617.376] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 4617.376] (**) AT Translated Set 2 keyboard: always reports core events
[ 4617.376] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 4617.376] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 4617.376] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 4617.376] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 4617.376] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 4617.376] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 11)
[ 4617.376] (**) Option "xkb_rules" "evdev"
[ 4617.376] (**) Option "xkb_model" "evdev"
[ 4617.376] (**) Option "xkb_layout" "us"
[ 4617.378] (II) config/udev: Adding input device ETPS/2 Elantech Touchpad (/dev/input/event10)
[ 4617.378] (**) ETPS/2 Elantech Touchpad: Applying InputClass "evdev touchpad catchall"
[ 4617.378] (**) ETPS/2 Elantech Touchpad: Applying InputClass "touchpad catchall"
[ 4617.378] (**) ETPS/2 Elantech Touchpad: Applying InputClass "Default clickpad buttons"
[ 4617.378] (II) LoadModule: "synaptics"
[ 4617.378] (II) Loading /usr/lib/xorg/modules/input/synaptics_drv.so
[ 4617.379] (II) Module synaptics: vendor="X.Org Foundation"
[ 4617.379] compiled for 1.14.1, module version = 1.7.1
[ 4617.379] Module class: X.Org XInput Driver
[ 4617.379] ABI class: X.Org XInput driver, version 19.1
[ 4617.379] (II) Using input driver 'synaptics' for 'ETPS/2 Elantech Touchpad'
[ 4617.379] (**) ETPS/2 Elantech Touchpad: always reports core events
[ 4617.379] (**) Option "Device" "/dev/input/event10"
[ 4617.380] (--) synaptics: ETPS/2 Elantech Touchpad: x-axis range 32 - 544 (res 0)
[ 4617.380] (--) synaptics: ETPS/2 Elantech Touchpad: y-axis range 32 - 352 (res 0)
[ 4617.380] (II) synaptics: ETPS/2 Elantech Touchpad: device does not report pressure, will use touch data.
[ 4617.380] (II) synaptics: ETPS/2 Elantech Touchpad: device does not report finger width.
[ 4617.380] (--) synaptics: ETPS/2 Elantech Touchpad: buttons: left right double triple
[ 4617.380] (--) synaptics: ETPS/2 Elantech Touchpad: Vendor 0x2 Product 0xe
[ 4617.380] (--) synaptics: ETPS/2 Elantech Touchpad: invalid pressure range. defaulting to 0 - 255
[ 4617.380] (--) synaptics: ETPS/2 Elantech Touchpad: invalid finger width range. defaulting to 0 - 15
[ 4617.380] (**) Option "TapButton1" "1"
[ 4617.380] (**) Option "TapButton2" "2"
[ 4617.380] (**) Option "TapButton3" "3"
[ 4617.381] (--) synaptics: ETPS/2 Elantech Touchpad: touchpad found
[ 4617.381] (**) ETPS/2 Elantech Touchpad: always reports core events
[ 4617.383] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input10/event10"
[ 4617.383] (II) XINPUT: Adding extended input device "ETPS/2 Elantech Touchpad" (type: TOUCHPAD, id 12)
[ 4617.383] (**) synaptics: ETPS/2 Elantech Touchpad: (accel) MinSpeed is now constant deceleration 2.5
[ 4617.383] (**) synaptics: ETPS/2 Elantech Touchpad: (accel) MaxSpeed is now 1.75
[ 4617.383] (**) synaptics: ETPS/2 Elantech Touchpad: (accel) AccelFactor is now 0.332
[ 4617.384] (**) ETPS/2 Elantech Touchpad: (accel) keeping acceleration scheme 1
[ 4617.384] (**) ETPS/2 Elantech Touchpad: (accel) acceleration profile 1
[ 4617.384] (**) ETPS/2 Elantech Touchpad: (accel) acceleration factor: 2.000
[ 4617.384] (**) ETPS/2 Elantech Touchpad: (accel) acceleration threshold: 4
[ 4617.384] (--) synaptics: ETPS/2 Elantech Touchpad: touchpad found
[ 4617.385] (II) config/udev: Adding input device ETPS/2 Elantech Touchpad (/dev/input/mouse0)
[ 4617.385] (**) ETPS/2 Elantech Touchpad: Ignoring device from InputClass "touchpad ignore duplicates"
[ 4617.386] (II) config/udev: Adding input device PC Speaker (/dev/input/event6)
[ 4617.386] (II) No input driver specified, ignoring this device.
[ 4617.386] (II) This device may have been added with another device file.
I've tried looking for this problem elsewhere as it feels like such a newbie problem to have, but I have had difficulty. There are two errors in this log, I think, but they didn't mean much to me... Any help for a linux newbie? Thanks!
EDIT: Solved; as pointed out below, I needed a window manager for a non-root user to use.
Last edited by DJMankiewicz (2013-06-05 07:30:06)Well, soon you'll have to try out one of the more minimal options, in which you don't use any desktop environment but instead you install your own window manager (openbox, dwm, i3, etc) and use small, dedicated programs. Given your extreme space restrictions, I recommend going that route! But, take your time because that requires a bit of learning: you need to figure out which parts of a desktop environment you really need, then you need to learn the proper names for them so that you can search for information, then you need to start fiddling with configurations, etc. Better first to make sure your first Arch Linux installation is up and running properly and to learn a bit about the system before entering that downward spiral.
-
7920 associates to root bridge but not to non-root bridge
I have 7920s using open authentication with WEP128 cipher. I have two 1300 root AP's (with client support) and three non-root AP's (also client support) in the same lab area. The root AP's and non-Root AP's associate and link to each other no problem. However, the 7920's will only associate with the Root APs. If I power down the root APs, the 7920s show "no AP found". I've verified SSID and WEP128 keys. I've also noted that the root AP does have a channel specified under dot11radio0 but the non-roots do not. Do the 7920's just scan for any channel until it finds an association or do I need to specify a channel in the non-root bridges?
Thanks,
Mike.With static WEP, the authentication is happening at the AP level. Will want to ensure non-root is associated to a root though otherwise the interface may be in "reset" state.
The 7920 will look at these 2 as individual APs regardless of channel. Non-roots should have the same channel as the root, otherwise will not be able to communicate.
Maybe you are looking for
-
I have two Creative Cloud accounts, occurred by accident, I wish to merge them and have all my details and licenses under one account, how do I do that? This is due to the different changes Adobe has gone through and unfortunately I used different em
-
Aperture: After changed the file name in Finder Aperture can't load the referenced file anymore
After I've changed the file name/format in Finder Aperture can't load/relink to the referenced file anymore. For some reasons I don't like to reimport the file.
-
Auto Import CD then Eject unreliable (works half the time)
I'm trying to re-rip my large collection of CDs, so I set my iTunes General Preferences to: When you insert a CD: [Import CD and Eject] Unfortunately, it doesn't work half the time. When it does work, it works as you might expect. I insert the CD, it
-
I am experiencing the following error after migrating code from v.4.5 to MX7. ***This code: <cfif isDefined("URL.Add")> <cfinsert DATASOURCE="eval" TABLENAME="tblGeneralEval" FORMFIELDS="SCHD_ID,date,class,instructor,rotrain_id,stuname,GQ1,GQ2,GQ3,GQ
-
ok so my camara is frozen. I restarted it and also rest the phone. it will show me the photos that i have taken but when i want to take a photo the screen is black and won't take one sometimes it will show me the camara on the front that face u but n